Tp-link 300mbps Wireless :: Pc Attached Via Lan Or Wifi To Wr841nd Can Ping Only
Nov 5, 2012
Region : Italy
Model : TL-WR841ND
Hardware Version : V8
Firmware Version : TL-WR841ND_V8_120802I
Setup the WR841ND in wds and easily connect to d-link.with the ping utility of the WR841ND I can reach the d-link or any of the PCs attached to the d-link and receive an answer.but any PC 'attached via LAN or WIFI to WR841ND can ping only WR841ND and not the d-link or any other PC attached to the d-link (clearly not even go on the Internet
Region : Mexico Model : TL-WR841ND Hardware Version : V8 Firmware Version : ISP : Telmex fiber
I use this router to replace the FO rooter that my ISP provides with the service as it's too limited (no NAT name translation, closes NAT, no uPnP etc...)
So the WR841ND acts as my main router, DHCP server, WiFi AP for all my network. My problem is that once in a while ( every 1 or 2 days) the wireless loses functionality, I still can see it from my devices, but can't connect, even fixing the IP (apparently not a DHCP issue then). The only way to fix this is to shut down the router 10 sec and restart it.
This brings another issue, I have another router (WR741) in WDS dispatching the signal to another part of the house to wired devices (Xbox , wd tv live hub) and it loses the WDS link, again the only way for this router to recover it is to restart it which is annoying.
Region : Portugal Model : TL-WR841ND Hardware Version : V8 Firmware Version : ISP :
Yesterday I bought this router to extend my wifi signar from my cable router. Now I know that it is possible using the WR841ND as an wifi extender using third-party firmwares but what I like to know is if there is any way to make the router work like that but using the original firmware. I followed a guide that explained how to do it but the only thing I can do is extend the wireless signal without the internet acess.
Region : Germany Model : TL-WR841ND Hardware Version : V8 Firmware Version : 8.1 ISP : M-Net
I set up my router and it does not get a WAN IP.The PPPoE user/pw ist 100% correct but in the "status field" it always says: "connecting" and i can't get an IP.The router is connected with the modem via RJ45 cabel that was in the box.My PC has no problem getting to the internet with direct modem communication (pppoe).
Model : TL-WR841ND Hardware Version : V8 Firmware Version : 3.13.18
I recently bought a wireless N router (TL-WR841ND). I could connect my laptop to internet using the router but the problem is whenever I try to connect my phone to the wireless network, it goes on and off. It'll be on for a few minutes and then it is off and so on. By the way, the phone says you're still connected to the router but actually there is no real internet connection. But anyway, my laptop is connected to internet anyways!
I am living in a dormitory. And the website of the ISP is url... which provides dynamic IP. I have already tried different LAN IP adresses.I have already tried MAC Clone for WAN but nothing changes.I'm in a dormitory, there is also other routers here, could it because of conflicts with the other routers? [code]
Region : Germany Model : TL-WR841ND Hardware Version : V3 Firmware Version : 3.13.18 ISP : [url]...
I recently bought a wireless N router (TL-WR841ND). I could connect my laptop to internet using the router but the problem is whenever I try to connect my phone to the wireless network, it goes on and off. It'll be on for a few minutes and then it is off and so on. By the way, the phone says you're still connected to the router but actually there is no real internet connection. But anyway, my laptop is connected to internet anyways! I have already tried MAC Clone for WAN but nothing changes.[code]....
Region : UnitedStates Model : TL-WR841ND Hardware Version : V5 Firmware Version : ISP : charter cable
I am trying to install a HP officejet 6700 all-in-one wireless printer on my home network. I can see the MAC and static IP addresses in the ARP list but fail to connect to it via my laptop. I have disabled the Norton Internet Security smart firewall and the windows firewall and still fail to connect. I have spent 2 four hour chat sessions with HP and they tell me it is my router. They had me change the channel to 6 from 5 and 11g-only from the 11gb-mixed and it still does not connect. They also had me do a firmware upgrade but the Printer was up to date.
Region : Malaysia Model : TL-WR841ND Hardware Version : V8 Firmware Version : 3.12.9 Build 120221 Rel.31475n ISP : UNIFI Telekoms
I am doing port forwarding for 2 webservers i have IP Address is 192.168.0.2 and 192.168.0.4 Both have web apps running find within LAN, both run on port 80.Error code: 14004.
Region : Others Model : TL-WR841ND Hardware Version : V8 Firmware Version : wr841nv8_en_3_13_27_up_boot(121101) ISP :
I followed TP-Link's guide to set up a WDS connection between my two brand new WR841ND router. It theoreticaly "works", but the network is extremly slow. Copying a ~100 Mb sized file to another computer on the other side takes more than 10 minutes or more, I don't know exactly, because I shut down the process after 10 min. I pinged the "slave" router with 200 packets, and I realized that every third, fourth and fifth packet has more than 500 ms time. The minimum is 4 ms, the longest was 566 ms.
Router A (Master) Connects to the internet/ADSL DHCP enabled
[Code].....
I bought the two router from the same dealer, at the same time. Both have the same firmware. I checked all the chanels, and 5 is the only free one, but the situation is the same on every chanel.
Region : Brazil Model : TL-WR841ND Hardware Version : V7 Firmware Version : 3.13.9 (Last) ISP : NET Virtua
I've bought a TL-WD841ND and was using it normally.
After I arrived from a trip, the internet speed by wireless and by cable is only 0,5~0,7 Mbps...
My internet connection is 10 Mbps, and if I plug direct on the modem, there comes the real speed (9,7 Mbps), but connecting by the router, the speed is 1/20 of what should be. Before my travel i was using it normal, and no one has changed any configuration.
So i've updated to the last firmware avaliable on the website. So i've rebooted it and the "configuration" LED keeps flashing...
I would like to know if this led flashing is normal: (here is a video that i've done: [URL] and what could be happening. ps: connecting by cable, the internet speed is also the same (even after the factory settings reset)...
Region : Romania Model : TL-WR841ND Hardware Version : Firmware Version : 3.13.27 Build 121101 Rel.38183n ISP : cosmote
hardware version is WR841N v8.wireless works just fine. i use it for my smartphone and an old laptop. i use ethernet cable to connect to main computer where all is ok until i start using my bit torrent client. as soon as i build up traffic above 1MB the ethernet portion of the router freezes and needs a reboot. when frozen, wireless is still working and i still have access on the lan to the router via my browser. i got this router so i could have wifi for my phone. my old router (asus rx3041) worked just fine and i accessed my isp at the maximum speeds it would allow on a 60 gigabit connection.
Region : UnitedStates Model : TL-WR841ND Hardware Version : V8 Firmware Version : ISP : optimum online I have two wireless routers: TP Link TL-WR841ND and TP Link TL-WR541G
I would like to:
use the TL-WR541G for my children wireless laptop, wireless ipad and wireless iphones. I can turn this unit off at a specific time each evening as I wish.
The WR841ND is used for my wireless laptop, wired iMac, wired Roku stream player and wired Voip adapter.
I tried a few things but really do not know what I am doing and I cannot get both wireless routers to access the internet.
What I tried so far:
Cable modem ethernet out to the input on the WR841ND router. took one of the four hardwire outputs from the WR841ND and ran into the input on the WR541G I powered on the cable modem....it booted... i then powered each router up and waited for each to boot. I launched web browser and navigated to : http://192.168.0.1/ this allowed me to setup the WR841ND router.
it's current settings: Firmware Version: 3.13.27 Build 121101 Rel.38183n Hardware Version: WR841N v8 00000000 WAN type: dynamic IP LAN IP address: 192.168.0.1 subnet mask: 255.255.255.0 DHCP Server: enabled Start IP: 192.168.0.100 End IP: 192.168.0.199
How do I set up the second router? I tried to disable the DHCP server on router 2 (WR541g) and change the IP but don't know what to change it to.
Region : UnitedStates Model : TL-WR1042ND Hardware Version : V1 Firmware Version : WR1042ND v1 00000000 ISP : comcast
I have a machine called 'survtest' on my lan with a permanent ip addr of 192.168.0.112. I can't ping that host by name from any other machine on the lan, although I can ping the ip address. Not only that but this machine appears in the DHCP client list within the router with its name 'survtest' and correct IP addr.
There is another machine on the lan called 'bsd' that also has a permanent IP addr of 192.168.0.110. It can be pinged by name from any other machine on the lan. However it does not show up in the DHCP client list at all.
Neither of these machines can be pinged by name from within the tplink admin diagnostic screen.
Region : Australia Model : TL-WR842ND Hardware Version : V1 Firmware Version : 3.12.24 Build 130110 Rel.58124n ISP :
The wireless drops out on my router every 1 or 2 days. I checked the LED on the router and it goes off when this occurs.I have attempted to turn WiFi back on using the 'on/off' button on the rear but it still won't work. The only remedy is to pull the power plug for a few moments and plug it back in.
Region : Canada Model : TL-WR1043ND Hardware Version : V1
I was wondering if it is possible to connect two routers through wireless and make them talk to each other. Here is why I need it, I currently Have 6 wireless IP Cameras going too 8. 2 are wired on one router in my house and the other 4 are wireless(with wired capabilities) Im going to wire the other 4 too a 2nd router so the cameras are always running and don't suffer any down time due to signal loss (happening a lot at the moment). How can I get Router B to talk to Router A, so I can look at all of the cameras from Laptop in my house which is closer to Router A.
My Router A is TL-WR1043ND, I'm also going to probably buy another one. How to configure it properly. So I can login to the cameras from my laptop.
-Region : UnitedKingdom -Model : TL-WR841N -Hardware Version : V8 -Firmware Version : 3.13.18 Build 120522 Rel.31564n -ISP : Virgin
I bought a TL-WR841N to use instead of our Virgin Super-hub which dropped the wifi regularly. It took me a while but I stumbled with the set up and got it working.Super-hub (in modem mode) - cable - TL-WR841N - 2 x cables running to 2 switches for (TV, Sky+, WII) and (PC, X-Box). Everything is spot on apart from the other half's Iphone and Ipad. Neither of them can get on the web in the bedroom. Both apples will join the network, but none will be able to get onto the web. The Wifi bars are on display on both products but they just keep spinning and searching to get on the web. I bought a Huawei repeater plug hoping that would work, but it just slows down everything else that can get on the network.Remembering that this happens only in one room, is there something that I can alter that would let these 2 apples access the web besides walking out on the landing every time she needs to update a web page ?
Region : India Model : TL-WR940N Hardware Version : Not Clear Firmware Version : 3.13.27 Build 121101 Rel.38183n
I have bought TP-Link TL-WR841N 300 mbps router. I have 20-25 wireless clients but only 15 wireless clients are able to connect to the router. Is there the limitation on numbers of wireless clients can connect to the router?
Region : Netherlands Model : TL-WR1043ND Hardware Version : v1 Firmware Version : V1_120405 ISP : UPC
After buying and installing i get no wlan/wifi connection.I do have internet by ethernet, the laptops and ipad sees the wlan/wifi but get no connection? Resetting re-installing manualy or with the wizard doesn't work.
Region : Netherlands Model : TL-WR1043ND Hardware Version : Not Clear Firmware Version :
I installed my brand new TP-Link router and both wired and wireless internet connection work perfectly fine. But when I tried to secure the wifi with a password (I followed the instructions on last page of installation guide) I can not connect to the internet any more. After entering the correct password, both iphone and mac-book simply say "unable to join the network". I selected WPA2-PSK-personal as recommended. For now I switched off the security settings, but I live in a building with many neighbours and they are now consuming most of my bandwidth (apparentlyI am surrounded by illegal downloaders
Region : UnitedStates Model : TL-WR1043ND Hardware Version : Not Clear Firmware Version : ISP : HughesNet
I received this router today, I have a MacBook Pro and a iPhone. The router came with a very small cd, I was very disappointed because , when I purchased this router from amazon , the discription read that this router is Mac compatiable. But that is not true if the cd is not compatiable! My problem is I get a good signal for wifi, but I can not open any websites with my Mac or my iphone.
Region : Others Model : TL-WR1043ND Hardware Version : Not Clear Firmware Version : ISP :
I have 2 TP-Link # 941NDs at my home. ( version 3.6 )In the new ( second ) TP link, i activate WDS - Wireless Bridge. And configure it to through Wi-Fi connect with earlier TP-Link, and also to act as router to cater to PCs within its range. IPs are set as per of same family as that of primary TP-Link, and further, DHCP been de-activated as well. Have sent WEP security as well.It performs correctly for the time, its stays ON, but when its switched Off, and then On again, it is not able to connect to the primary TP-Link and thus not able to serve its client PCs.
Region : Others Model : TL-WR941ND Hardware Version : V3 Firmware Version : 3.13.9 Build 120201 Rel.54965n
We are trying to use a TL-WR941ND purchased about a month ago, but it keeps hanging, usually within a day or so of operation.To be clear: by "hanging" I mean the device stops providing wireless services (its SSID is no longer visible in WiFi clients) and becomes nonresponsive to pings or control access attempts (via settings web page) from the internal network connections.The device is used in a very simple scenario, where it's being employed as a simple access point, not as a router. As such, the device's configuration is as follows:
* WAN interface is configured with a dummy static IP (10.10.10.10/24) with gateway and DNS set to the internal IP address of the actual routing device connected to the external world. * LAN interface is configured with an IP address inside the actual internal IP subnet (192.168.1.0/24). * DHCP is also disabled as this service is already provided. * Wireless settings: radio enabled, SSID broadcast enabled, WDS disabled, 11bgn mixed mode, auto channel width, max TX rate, channel 7 (manually set). Using WPA-PSK security.
Rest of the settings are unchanged from their default values, as the device isn't being used as an IP router by any client - just as a WiFi/Ethernet layer 2 bridge. We're using what appears to be TP-Link's latest stock firmware for the device.The settings described above appear to provide the connectivity required by the WiFi clients. However, the device continuously hangs within a day or so of operation, requiring someone to physically attend to the device and cold-restarting it (disconnecting it from power and reconnecting it) to regain an operational state.
After performing a cold restart, the system log shows nothing beyond the startup entries: "System started" entry followed by security info entries regarding enabled protocols. Then the device appears to work well for a while, until it hangs again, forcing again someone to attend to the device, etc.
Region : Poland Model : TL-WR941ND Hardware Version : V3 Firmware Version : ISP :
I have a problem with files sharing via wi-fi. I can not share files over the network using wi-fi connections. While the network is the cable connection sharing is available. The network also acts as one computer is connected by a cable to the router and the other via wifi. But if the two computers are working through wifi network does not work. Are there any settings in the router, which can cause blocking calls via wifi?
Region : Belgium Model : TL-WR1043ND Hardware Version : V1 Firmware Version : 3.13.12 Build 120405 Rel.33996n ISP : Telenet
I've just bought a TP-Link TL_WR1043ND and when I was configuring the wireless settings first I had a +- 40Mbps connection,a little later the connection dropped to 4Mbps and was constantly dropping the speed.Sometimes it went to 15Mbps and then it drops back to 4Mbps.Right now its only 1Mbps.
Configuration:
Wireless channel: 11 Mode: 11bgn mixed Channel width: Auto Max tx rate: 300Mbps Wireless router radio and SSID broadcasting enabled
Region : Romania Model : TL-WR1043ND Hardware Version : V1 Firmware Version : latest ISP : RDS
I am experiencing an issue since I bought my new laptop.I connect to the Internet with Windows 8 and TL-WR1043ND.My issue is that ever since I installed the printer utility from the site I hear an ON/OFF sound in my speaker randomly and I can not figure out what`s wrong.I think it`s trying to search for my printer but it it off.Also wi-fi disconnects randomly ever since this application was installed.What can I do to fix this issue.Computer works fine without the application.There is no report about this issue in the Event Viewer.
I need a wireless router to transmit internet in my home, it's on two floors, my only concern is that the floor is really thick and I'm gonna be working in the basement. I need to choose between the following, can you tell me which is best?
I have recently acquired a network connection of 100Mbps download and upload, and a dir 615 with dd-wrt.
I made all the connections and configurations , and everything seems to work fine it says it's connected at 300 mbps wifi, except it is not . I tested the internet speed and got this :
80 mbps Upload 35 mbps Download
I know that connecting via wifi will loose bandwith, the problem ins't that, I just cant seem to find the cause for the download rate to be less than upload and not equal... , when connected to the cable I get a stable 100/100.
I bought this router to extend my wifi signar from my cable router. Now I know that it is possible using the WR841ND as an wifi extender using third-party firmwares but what I like to know is if there is any way to make the router work like that but using the original firmware. I followed a guide that explained how to do it but the only thing I can do is extend the wireless signal without the internet acess.
Anyone using it to save videos from their cams? Are you using Synology NAS? Am interested and want to hear from people qualified to discuss NAS. Qualified means you are currently using NAS or have thoroughly researched it to the point you have made your purchase decision for the most part.
I recently purchased a NAS enclosure to use my WD IDE hard drive as a networked drive. I configured the hard drive's jumper setting as single (no jumper). I installed the hard drive in the enclosure and connected the Cat 5e cable to the back of the DIR-655 router. When I tried mapping to the drive, I receive the error:
\STORAGE-3B25 is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions. Network error (1208).
I suspect perhaps that I might need to change a setting on my router to allow me to access the NAS. The NAS ip address is visible on the router's admin page and I am able to see it when searching for network drives in my laptop. But I just somehow can't connect to it. I am running Windows 7 Professional 32-bit.
I am currently running a TL-WR851ND Wifi Router whith the latest build 3.13.27 Build 121101 Rel.38183n() published last November 2012. Now is there any new firmware?
