I bought this router to extend my wifi signar from my cable router. Now I know that it is possible using the WR841ND as an wifi extender using third-party firmwares but what I like to know is if there is any way to make the router work like that but using the original firmware. I followed a guide that explained how to do it but the only thing I can do is extend the wireless signal without the internet acess.
View 1 RepliesRegion : Portugal
Model : TL-WR841ND
Hardware Version : V8
Firmware Version :
ISP :
Yesterday I bought this router to extend my wifi signar from my cable router. Now I know that it is possible using the WR841ND as an wifi extender using third-party firmwares but what I like to know is if there is any way to make the router work like that but using the original firmware. I followed a guide that explained how to do it but the only thing I can do is extend the wireless signal without the internet acess.
Region : Italy
Model : TL-WR841ND
Hardware Version : V8
Firmware Version : TL-WR841ND_V8_120802I
Setup the WR841ND in wds and easily connect to d-link.with the ping utility of the WR841ND I can reach the d-link or any of the PCs attached to the d-link and receive an answer.but any PC 'attached via LAN or WIFI to WR841ND can ping only WR841ND and not the d-link or any other PC attached to the d-link (clearly not even go on the Internet
Region : Mexico
Model : TL-WR841ND
Hardware Version : V8
Firmware Version :
ISP : Telmex fiber
I use this router to replace the FO rooter that my ISP provides with the service as it's too limited (no NAT name translation, closes NAT, no uPnP etc...)
So the WR841ND acts as my main router, DHCP server, WiFi AP for all my network. My problem is that once in a while ( every 1 or 2 days) the wireless loses functionality, I still can see it from my devices, but can't connect, even fixing the IP (apparently not a DHCP issue then). The only way to fix this is to shut down the router 10 sec and restart it.
This brings another issue, I have another router (WR741) in WDS dispatching the signal to another part of the house to wired devices (Xbox , wd tv live hub) and it loses the WDS link, again the only way for this router to recover it is to restart it which is annoying.
I installed a tp link extender to boost wifi at home (2 storey) and since then I have noticed that upstairs where the router is installed the signal is weaker than downstairs where the extender is located.
View 2 Replies View RelatedAt the moment the Wireless Router is located in my bedroom which is 12 meters from the living room where the phone line is. I basically have one phone line extension from the telephone line to my bedroom where I've plugged in the ADSL filter. The modem part plugs into the actual router and the telephone line is then extended back to the living room with a second extension cable.This is because my PC is in my bedroom. Problem with this is the fact that there are extension cables get in the way when moving furniture around and also hang from the ceiling in the corridor.What I'd like to do is have a WiFi dongle for my PC and move the router to the living room. Now my second problem is that my phone gets a very weak WiFi signal once you go to the living room so I imagine if I moved the router to there then I would barely get a signal in my bedroom. I have two options to solve this:
(1) Use a WiFi extender in between my room and the router and then a dongle for my computer
(2) Upgrade my current G router to an N router. Problem is I'm not too sure the signal will reach my room. There's a 12 meter range from the living room to my bedroom btw.url...
ADSL Box in office ground floor - Range extender in 1st floor lounge - portable Win7 64 in dining room next to lounge (1st floor) Setup proceeds and completes as it should but the problem: The portable connects to the new link *_EXT but with "no access" (the extender is not connecting to the router). Having read several reviews about connection problems with this kit, none seem to have the problem I have.
View 10 Replies View RelatedThe router I'm connecting it with is a bright house RCA dwg855t. I go through the setup and the net gear device isn't receiving an IP address from the router.
View 1 Replies View Relatedbuying a wireless router to use as a wifi extender as the signal is weak upstairs. At the moment my pc upstairs is connected by ethernet cable, I'm thinking of connecting a router upstairs to this ethernet cable to have good wifi upstairs. And my pc does have wifi so I will use that.
View 1 Replies View RelatedWhat Wifi Extender will work with a 2Wire 707 380 1HGV?
View 2 Replies View RelatedI'm running Windows Vista on PC. Have a Netgear router. Just bought Netgear range extender WN3000RP. Have the extender plugged in and light is green. When I try my PC's wireless network manager, it does not recognize any wireless devices to add. How can I connect to the extender wireless network when it is not recognized on my wireless manager??
View 1 Replies View RelatedI just installed a Netgear WiFi extender. In order to set all the preferences, it wants a password and login and I have no idea what that is. I tried everything I could think of, but no go. how to reset the pw and figure out what my login is? Have had no response that addresses this problem. I am using Win 7 and I have an ARRIS cable modem. I've already gone thru the users guide with a fine tooth comb and have found nothing. I have been using WiFi on Netgear equipment for years, so it's not a new network. I also tried the login=admin and password=password and that didn't work.
View 3 Replies View RelatedWill a Wi-Fi range extender affect (i.e., reduce) the signal of the router? How does the throughput signal compare between where it originates and where it ends?
View 2 Replies View RelatedI have a wireless modem but its a sucky one. It was one of those free ones from verizon. Anyways, I don't get good signal in certain places in my house, so i am interested in knowing which would be better a wifi range extender or a good wireless modem.
View 1 Replies View RelatedCan N600 DB Wi-Fi Range Extender have the exact same name as my N600 DB Router or does the extender have to have the additional characters "_xt" at the end of the extender name, when the first part matches the router name?
View 1 Replies View RelatedI work at a Public Safety building in Pennsylvania and our employees here share a Wifi connection with a local hospital facility that is in a industrial park behind us. The room we work in is able to access the Public Wifi but only half of the room has a good connection. I went to the local computer store and purchased a Belkin Dual-band wireless Range Extender and got it all set up, now I have the Public Wifi Extention access and it will connect to it but it has no internet access. Now we have no access to the administor or the network from our facility. How do i get internet access thru this range extender? If i connect from the good half of the room to the Public wifi i have a good connection with internet access but as soon as you put it thru the extender no more internet access.
View 1 Replies View RelatedBought the Zyxel Wireless Range Extender to get wifi in farthest rooms in my house but set up is not working because BT have disabled WPS button on Home Hub 3 with my Infinity. Therefore they suggest I try manual set up. This requires browser wtih IP address 192.168.1.2 for Zyxel wireless extender WRE2205, This gives no result (page does not load in IE).
View 1 Replies View RelatedI need a wifi extender for wag 120n , and i want to connect it with WDSI use wag 120n as main and only modem and access pointWhat is the best and cheapest device for me?
View 1 Replies View RelatedMy objective is to use the USB port on the E1550 to share an external hard drive for my family's shared media files.I have moved into a rental home with little cat5 wiring. Internet service is Uverse.Given the wiring situation, I bought a netgear universal dual band range extender which connects wirelessly to the uverse router in another room. My home office equipment (computer, printer) are wired into the netgear. All of that works fine. The netgear is 192.168.1.66. The computer is 192.168.1.128. So, I wanted to add the E1550 into my network. I can see it as an attached device on the Netgear's admin page, but cisco connect and a direct ip http://192.168.1.68 does not resolve. I have the e1550 connected via a lan port on the netgear extender (there is no other option). I have gone from that lan port to the internet port on the e1550. I have done so with a staight Cat5 cable and with what I believe should be a cross-over. In both situations, I see the router via the netgear admin page but can not connect to it. I'd prefer not the hang my usb drive off of my computer because it if gets turned off or reboots due to a MS Windows auto update, it leaves the rest of the house with no shared media during that process.
View 1 Replies View Relatedtrying to setup universal wifi extender. Lights indicate system is on and connected to my computer. however wps and link rate lights are not on.
View 1 Replies View RelatedHow compatible is my WRT610N V2 with your Linksys PLWK400 Wireless-N Wi-Fi Extender Kit?
View 2 Replies View RelatedI have a WN3000RP WiFi Range Extender but I cannot seem to find out how to connect to it on my Windows 7 Desktop computer to configure it. My Router is a Netgear Wireless G RouterWGR614 v9
View 7 Replies View RelatedRegion : Singapore
Model : TL-WR700N
Hardware Version : V1
Firmware Version :
Since i know there's a "Repeater Operation Mode" in TL-WR700N Wireless Lan Mini Pocket Router, so what's the difference between TL-WA850RE WiFi Range Extender?I know the maxium speed support is different, but.... what else ?
I am having problem using the N300 dual-Ban Wi-Fi Range extender with my att 2wire 3800HGV-B router. Cannot use the extender to access the internet. The Att router works without it. Just want to use the extender to extend my att router signal but cannot.
View 3 Replies View RelatedCan I put more than one N300 Dual-Band Wi-Fi Range Extender on my home network?
View 4 Replies View RelatedI'm trying to configure mine as a wireless repeater, but to no avail. Here's what I've done so far: disabled WPS changed my router's IP to 192.168.0.2 (because the source router's IP is 192.168.0.1) rebooted the router enabled WDS, found the network I want to repeat using the Survey feature, then filled in the WPA2 password. enabled WPA2 security on my own repeated network, using the same authentication type and password as the original rebooted the router.
My router complains that "WAN port is unplugged", and it doesn't get a WAN IP or incoming packets, which probably means it's expecting the internet signal to come from the WAN port rather than the wireless network I set up, right? How can I force the router to connect to the network? Also, should both routers be in the same subnet? I've tried with different subnets but nothing changes. The source router is a D-Link DIR-600.
Recently I had changed my ISP and I get a brand new modem and a D-Link DIR-615 wireless router, but the problem is the wireless signal is not strong enough to reach second floor, so I decided to get a new TP-Link TL-WA901ND access point and after configure the AP to repeaters mode, I saw it has traffic coming throughout to the AP but my PC cannot get any internet connection not even an IP address. When I was facing this problem, I thinking of is that possible using my old wireless router which is TP-Link TL-WR841ND to have a internet connection working with D-Link wireless router, I had tried plug my TP-Link router LAN port to D-Link router LAN port with a network cable and setting into same IP range (192.169.0.xx) but cannot get any traffic getting through.
View 2 Replies View RelatedRegion : Germany
Model : TL-WR841ND
Hardware Version : V8
Firmware Version : 8.1
ISP : M-Net
I set up my router and it does not get a WAN IP.The PPPoE user/pw ist 100% correct but in the "status field" it always says: "connecting" and i can't get an IP.The router is connected with the modem via RJ45 cabel that was in the box.My PC has no problem getting to the internet with direct modem communication (pppoe).
Region : Others
Model : TL-WR841ND
Hardware Version : V7
Firmware Version :
ISP :
my ip address is not static i use no-ip sevice to get dns how to set my tp link for wake on lan
I managed to update ddns in my tp link How do I go from here?
Model : TL-WR841ND
Hardware Version : V8
Firmware Version : 3.13.18
I recently bought a wireless N router (TL-WR841ND). I could connect my laptop to internet using the router but the problem is whenever I try to connect my phone to the wireless network, it goes on and off. It'll be on for a few minutes and then it is off and so on. By the way, the phone says you're still connected to the router but actually there is no real internet connection. But anyway, my laptop is connected to internet anyways!
I am living in a dormitory. And the website of the ISP is url... which provides dynamic IP. I have already tried different LAN IP adresses.I have already tried MAC Clone for WAN but nothing changes.I'm in a dormitory, there is also other routers here, could it because of conflicts with the other routers? [code]
Region : Germany
Model : TL-WR841ND
Hardware Version : V3
Firmware Version : 3.13.18
ISP : [url]...
I recently bought a wireless N router (TL-WR841ND). I could connect my laptop to internet using the router but the problem is whenever I try to connect my phone to the wireless network, it goes on and off. It'll be on for a few minutes and then it is off and so on. By the way, the phone says you're still connected to the router but actually there is no real internet connection. But anyway, my laptop is connected to internet anyways! I have already tried MAC Clone for WAN but nothing changes.[code]....
I need a wireless router to transmit internet in my home, it's on two floors, my only concern is that the floor is really thick and I'm gonna be working in the basement. I need to choose between the following, can you tell me which is best?
View 1 Replies View RelatedRegion : UnitedStates
Model : TL-WR841ND
Hardware Version : V5
Firmware Version :
ISP : charter cable
I am trying to install a HP officejet 6700 all-in-one wireless printer on my home network. I can see the MAC and static IP addresses in the ARP list but fail to connect to it via my laptop. I have disabled the Norton Internet Security smart firewall and the windows firewall and still fail to connect. I have spent 2 four hour chat sessions with HP and they tell me it is my router. They had me change the channel to 6 from 5 and 11g-only from the 11gb-mixed and it still does not connect. They also had me do a firmware upgrade but the Printer was up to date.