I need a wireless router to transmit internet in my home, it's on two floors, my only concern is that the floor is really thick and I'm gonna be working in the basement. I need to choose between the following, can you tell me which is best?
View 1 RepliesRegion : Brazil
Model : TL-WR841ND
Hardware Version : V7
Firmware Version : 3.13.9 (Last)
ISP : NET Virtua
I've bought a TL-WD841ND and was using it normally.
After I arrived from a trip, the internet speed by wireless and by cable is only 0,5~0,7 Mbps...
My internet connection is 10 Mbps, and if I plug direct on the modem, there comes the real speed (9,7 Mbps), but connecting by the router, the speed is 1/20 of what should be. Before my travel i was using it normal, and no one has changed any configuration.
So i've updated to the last firmware avaliable on the website. So i've rebooted it and the "configuration" LED keeps flashing...
I would like to know if this led flashing is normal: (here is a video that i've done: [URL] and what could be happening. ps: connecting by cable, the internet speed is also the same (even after the factory settings reset)...
Region : Germany
Model : TL-WR841ND
Hardware Version : V8
Firmware Version : 8.1
ISP : M-Net
I set up my router and it does not get a WAN IP.The PPPoE user/pw ist 100% correct but in the "status field" it always says: "connecting" and i can't get an IP.The router is connected with the modem via RJ45 cabel that was in the box.My PC has no problem getting to the internet with direct modem communication (pppoe).
Region : United Kingdom
Model : TL-WR841ND
Hardware Version : Not Clear
Firmware Version : 7.1
ISP :
failed to verify router settings
What's wrong with my router?
the Xbox part was a windows thing. The router, modem, computer, and monitor, are all on one powerbar. I have used the used-to-be-wired computer (I needed the ethernet cord for something else, haven't gotten around to plugging it back in.) and the wireless laptop loses connection periodically. ALWAYS lose connection on bootup. and also when doing power consuming things. SO, I believe it is a lack of power being sent to the router. wired connections would use less, thats why they are still active, but I assume the wireless transmitter needs more energy in order to function properly. I haven't used the old computer in a awhile now, but I assume if I plug the router into another outlet/curcuit I the problem wouldnt occur. Might need someone wiht more knowledge to confirm this, but I'm fairly certain this was the cause.
View 3 Replies View RelatedRegion : Others
Model : TL-WR841ND
Hardware Version : V7
Firmware Version :
ISP :
my ip address is not static i use no-ip sevice to get dns how to set my tp link for wake on lan
I managed to update ddns in my tp link How do I go from here?
Model : TL-WR841ND
Hardware Version : V8
Firmware Version : 3.13.18
I recently bought a wireless N router (TL-WR841ND). I could connect my laptop to internet using the router but the problem is whenever I try to connect my phone to the wireless network, it goes on and off. It'll be on for a few minutes and then it is off and so on. By the way, the phone says you're still connected to the router but actually there is no real internet connection. But anyway, my laptop is connected to internet anyways!
I am living in a dormitory. And the website of the ISP is url... which provides dynamic IP. I have already tried different LAN IP adresses.I have already tried MAC Clone for WAN but nothing changes.I'm in a dormitory, there is also other routers here, could it because of conflicts with the other routers? [code]
Region : Germany
Model : TL-WR841ND
Hardware Version : V3
Firmware Version : 3.13.18
ISP : [url]...
I recently bought a wireless N router (TL-WR841ND). I could connect my laptop to internet using the router but the problem is whenever I try to connect my phone to the wireless network, it goes on and off. It'll be on for a few minutes and then it is off and so on. By the way, the phone says you're still connected to the router but actually there is no real internet connection. But anyway, my laptop is connected to internet anyways! I have already tried MAC Clone for WAN but nothing changes.[code]....
Region : Italy
Model : TL-WR841ND
Hardware Version : V8
Firmware Version : TL-WR841ND_V8_120802I
Setup the WR841ND in wds and easily connect to d-link.with the ping utility of the WR841ND I can reach the d-link or any of the PCs attached to the d-link and receive an answer.but any PC 'attached via LAN or WIFI to WR841ND can ping only WR841ND and not the d-link or any other PC attached to the d-link (clearly not even go on the Internet
Region : Mexico
Model : TL-WR841ND
Hardware Version : V8
Firmware Version :
ISP : Telmex fiber
I use this router to replace the FO rooter that my ISP provides with the service as it's too limited (no NAT name translation, closes NAT, no uPnP etc...)
So the WR841ND acts as my main router, DHCP server, WiFi AP for all my network. My problem is that once in a while ( every 1 or 2 days) the wireless loses functionality, I still can see it from my devices, but can't connect, even fixing the IP (apparently not a DHCP issue then). The only way to fix this is to shut down the router 10 sec and restart it.
This brings another issue, I have another router (WR741) in WDS dispatching the signal to another part of the house to wired devices (Xbox , wd tv live hub) and it loses the WDS link, again the only way for this router to recover it is to restart it which is annoying.
Region : UnitedStates
Model : TL-WR841ND
Hardware Version : V5
Firmware Version :
ISP : charter cable
I am trying to install a HP officejet 6700 all-in-one wireless printer on my home network. I can see the MAC and static IP addresses in the ARP list but fail to connect to it via my laptop. I have disabled the Norton Internet Security smart firewall and the windows firewall and still fail to connect. I have spent 2 four hour chat sessions with HP and they tell me it is my router. They had me change the channel to 6 from 5 and 11g-only from the 11gb-mixed and it still does not connect. They also had me do a firmware upgrade but the Printer was up to date.
Region : Malaysia
Model : TL-WR841ND
Hardware Version : V8
Firmware Version : 3.12.9 Build 120221 Rel.31475n
ISP : UNIFI Telekoms
I am doing port forwarding for 2 webservers i have IP Address is 192.168.0.2 and 192.168.0.4 Both have web apps running find within LAN, both run on port 80.Error code: 14004.
Region : Portugal
Model : TL-WR841ND
Hardware Version : V8
Firmware Version :
ISP :
Yesterday I bought this router to extend my wifi signar from my cable router. Now I know that it is possible using the WR841ND as an wifi extender using third-party firmwares but what I like to know is if there is any way to make the router work like that but using the original firmware. I followed a guide that explained how to do it but the only thing I can do is extend the wireless signal without the internet acess.
Region : Others
Model : TL-WR841ND
Hardware Version : V8
Firmware Version : wr841nv8_en_3_13_27_up_boot(121101)
ISP :
I followed TP-Link's guide to set up a WDS connection between my two brand new WR841ND router. It theoreticaly "works", but the network is extremly slow. Copying a ~100 Mb sized file to another computer on the other side takes more than 10 minutes or more, I don't know exactly, because I shut down the process after 10 min. I pinged the "slave" router with 200 packets, and I realized that every third, fourth and fifth packet has more than 500 ms time. The minimum is 4 ms, the longest was 566 ms.
Router A (Master)
Connects to the internet/ADSL
DHCP enabled
[Code].....
I bought the two router from the same dealer, at the same time. Both have the same firmware. I checked all the chanels, and 5 is the only free one, but the situation is the same on every chanel.
What can couse this very slow transfer speed?
Region : Romania
Model : TL-WR841ND
Hardware Version :
Firmware Version : 3.13.27 Build 121101 Rel.38183n
ISP : cosmote
hardware version is WR841N v8.wireless works just fine. i use it for my smartphone and an old laptop. i use ethernet cable to connect to main computer where all is ok until i start using my bit torrent client. as soon as i build up traffic above 1MB the ethernet portion of the router freezes and needs a reboot. when frozen, wireless is still working and i still have access on the lan to the router via my browser. i got this router so i could have wifi for my phone. my old router (asus rx3041) worked just fine and i accessed my isp at the maximum speeds it would allow on a 60 gigabit connection.
Region : UnitedStates
Model : TL-WR841ND
Hardware Version : V8
Firmware Version :
ISP : optimum online
I have two wireless routers:
TP Link TL-WR841ND
and
TP Link TL-WR541G
I would like to:
use the TL-WR541G for my children wireless laptop, wireless ipad and wireless iphones.
I can turn this unit off at a specific time each evening as I wish.
The WR841ND is used for my wireless laptop, wired iMac, wired Roku stream player and wired Voip adapter.
I tried a few things but really do not know what I am doing and I cannot get both wireless routers to access the internet.
What I tried so far:
Cable modem ethernet out to the input on the WR841ND router. took one of the four hardwire outputs from the WR841ND and ran into the input on the WR541G I powered on the cable modem....it booted... i then powered each router up and waited for each to boot. I launched web browser and navigated to : http://192.168.0.1/ this allowed me to setup the WR841ND router.
it's current settings:
Firmware Version: 3.13.27 Build 121101 Rel.38183n
Hardware Version: WR841N v8 00000000
WAN type: dynamic IP
LAN IP address: 192.168.0.1
subnet mask: 255.255.255.0
DHCP Server: enabled
Start IP: 192.168.0.100
End IP: 192.168.0.199
How do I set up the second router? I tried to disable the DHCP server on router 2 (WR541g) and change the IP but don't know what to change it to.
With firmware 2.06 my DIR-600 had transmit power choices 100%, 50%, 25% and 12,5%.(even 12,5% gave me excellent strength on all my devices, what is really the difference)But after updating to firmware 2.11 (via 2.10, othervise my DIR-600 refused to use 2.11)the choices for transmit power is now only "High", "Medium" and "Low". know the percentage values for those three settings?
View 2 Replies View RelatedI have a TV tuner card and Wifi router. Can I transmit the TV signal through Wifi router to my Laptop. How?
View 1 Replies View RelatedRecently I had changed my ISP and I get a brand new modem and a D-Link DIR-615 wireless router, but the problem is the wireless signal is not strong enough to reach second floor, so I decided to get a new TP-Link TL-WA901ND access point and after configure the AP to repeaters mode, I saw it has traffic coming throughout to the AP but my PC cannot get any internet connection not even an IP address. When I was facing this problem, I thinking of is that possible using my old wireless router which is TP-Link TL-WR841ND to have a internet connection working with D-Link wireless router, I had tried plug my TP-Link router LAN port to D-Link router LAN port with a network cable and setting into same IP range (192.169.0.xx) but cannot get any traffic getting through.
View 2 Replies View RelatedI recently bought a Nintendo 3DS but unfortunately my University's wireless security (WPA2 Enterprise) is incompatible with the system. As such, I was looking for a way to transmit a wireless signal from my computer, and place an alternative form of security onto it (such as WEP), so that the 3DS can connect to it.
At the moment, my desktop is connected via ethernet cable, which plugs directly into a wall socket. I'm pretty unsure as to what to use, I've heard of things such as 'wireless bridges', but I'm not sure how they work. Also, I'm looking for the device to transmit a signal even if my desktop isn't turned on. Is a router my only option?
i have ipod but i dont have wireless modem i need software thats work from my pc as wireless modem
View 2 Replies View RelatedWRV200 does not transmit packets in Router mode. This issue has been describes already here:
[url]....
So is there a solution to forcing this router function properly according to manufacturer's declaration (router mode)?
I need to transfer live video and if possible video from station A to station B over wireless network. So what are the hardware requirements and setup cost...
Secondly how should i connect my CCTv cameras atleast 5 to computer's webcam so that i can transfer video over internet.
How do I - from my stereo amplifier wireless transmit to two stereo speakers?
View 1 Replies View RelatedI will be doing a site survey using the client's Cisco 1262 with only 1 radio (g/n), 3 antennas. What is the maximum transmit power, 20dBm or 23dBm? I need to set the transmit power in the Airmagnet to 50% or 3dBm down as recommended by Cisco.
View 4 Replies View Relatedmaximum size I can set the Transmit/Recieve Buffers to for the WMP600N wireless adapter.
View 4 Replies View RelatedI have an AP1242 near a couple of conference rooms. I get complaints when we have a large contingent in there and some try to download documents. The bandwidth consumption is meage - less than 2Mbps. But there could be say 50 people in those training rooms. I see no errors at the FE interface on the AP but I do see a good number of Transmit Discards.
Are 50 users connected to an AP1242 simply more than should be expected of the device? 802.11g is the radio.
Are transmit discards indicative of some kind of configuration problem? The users in these cases are generally very close to the access point - within a few feet even.
If it is indicative of a configuration problem would that be an issue of the configuration of the laptop wifi cards or a problem at the AP?
I bought this router to extend my wifi signar from my cable router. Now I know that it is possible using the WR841ND as an wifi extender using third-party firmwares but what I like to know is if there is any way to make the router work like that but using the original firmware. I followed a guide that explained how to do it but the only thing I can do is extend the wireless signal without the internet acess.
View 1 Replies View RelatedI'm trying to configure mine as a wireless repeater, but to no avail. Here's what I've done so far: disabled WPS changed my router's IP to 192.168.0.2 (because the source router's IP is 192.168.0.1) rebooted the router enabled WDS, found the network I want to repeat using the Survey feature, then filled in the WPA2 password. enabled WPA2 security on my own repeated network, using the same authentication type and password as the original rebooted the router.
My router complains that "WAN port is unplugged", and it doesn't get a WAN IP or incoming packets, which probably means it's expecting the internet signal to come from the WAN port rather than the wireless network I set up, right? How can I force the router to connect to the network? Also, should both routers be in the same subnet? I've tried with different subnets but nothing changes. The source router is a D-Link DIR-600.
I've got an ASUS G50V that I normally connect to the net through a wireless router but I recently bought a router so I can make a physical connection and increase speed. However I cant get it to connect to the router no matter what I do (i had it working for a few hours at one point but it dropped off again).I confirmed it wasnt the router but running a crossover cable from the laptop to my desktop, setting static ips on both. Now I can ping the laptop from my desktop but for some reason I cannot ping the desktop from the lappy. I've tried everything I can think of but no dice.
View 4 Replies View RelatedI have a AIR-AP1121G-A-K9 running c1100-k9w7-tar.123-7.JA2 (Autonomous)We have monitoring setup with Orion NPM and we consistently see output errors, Transmit discards and big buffer errors The users at the site have not reporting any issues but was wondering how to prevent these or are these normal?What causes the output errors on Wireless Radio ? How to troubleshoot further ?
Radio0-802.11G
Total Output Errors 0 47749
Small Buffer Misses
4 misses
139 misses
[code]....
I have a client(C) and a server(S) nodes plus an intermediate node(I). Each node has a public IP. What I want to do is to transmit some data(whatever) from C to S but this data to go through I. So C ---> S will become C ----> I ----> S. I read something to create a tunnel(ip add tunnel) between C and I and add a route between them ? I tried different examples but did not work at all.
View 2 Replies View RelatedI am unable to transmit e-mails to a friend , using "docomo.ne.jp" as her provider, and get no assistance from mailer-daemon at this end.
View 3 Replies View Related