TP-Link 300Mbps Wireless :: TL-WR841ND - LAN Freezes With High Bandwidth Usage
Jan 13, 2013
Region : Romania
Model : TL-WR841ND
Hardware Version :
Firmware Version : 3.13.27 Build 121101 Rel.38183n
ISP : cosmote
hardware version is WR841N v8.wireless works just fine. i use it for my smartphone and an old laptop. i use ethernet cable to connect to main computer where all is ok until i start using my bit torrent client. as soon as i build up traffic above 1MB the ethernet portion of the router freezes and needs a reboot. when frozen, wireless is still working and i still have access on the lan to the router via my browser. i got this router so i could have wifi for my phone. my old router (asus rx3041) worked just fine and i accessed my isp at the maximum speeds it would allow on a 60 gigabit connection.
Region : Germany Model : TL-WR841ND Hardware Version : V8 Firmware Version : 8.1 ISP : M-Net
I set up my router and it does not get a WAN IP.The PPPoE user/pw ist 100% correct but in the "status field" it always says: "connecting" and i can't get an IP.The router is connected with the modem via RJ45 cabel that was in the box.My PC has no problem getting to the internet with direct modem communication (pppoe).
Model : TL-WR841ND Hardware Version : V8 Firmware Version : 3.13.18
I recently bought a wireless N router (TL-WR841ND). I could connect my laptop to internet using the router but the problem is whenever I try to connect my phone to the wireless network, it goes on and off. It'll be on for a few minutes and then it is off and so on. By the way, the phone says you're still connected to the router but actually there is no real internet connection. But anyway, my laptop is connected to internet anyways!
I am living in a dormitory. And the website of the ISP is url... which provides dynamic IP. I have already tried different LAN IP adresses.I have already tried MAC Clone for WAN but nothing changes.I'm in a dormitory, there is also other routers here, could it because of conflicts with the other routers? [code]
Region : Germany Model : TL-WR841ND Hardware Version : V3 Firmware Version : 3.13.18 ISP : [url]...
I recently bought a wireless N router (TL-WR841ND). I could connect my laptop to internet using the router but the problem is whenever I try to connect my phone to the wireless network, it goes on and off. It'll be on for a few minutes and then it is off and so on. By the way, the phone says you're still connected to the router but actually there is no real internet connection. But anyway, my laptop is connected to internet anyways! I have already tried MAC Clone for WAN but nothing changes.[code]....
Region : Italy Model : TL-WR841ND Hardware Version : V8 Firmware Version : TL-WR841ND_V8_120802I
Setup the WR841ND in wds and easily connect to d-link.with the ping utility of the WR841ND I can reach the d-link or any of the PCs attached to the d-link and receive an answer.but any PC 'attached via LAN or WIFI to WR841ND can ping only WR841ND and not the d-link or any other PC attached to the d-link (clearly not even go on the Internet
Region : Mexico Model : TL-WR841ND Hardware Version : V8 Firmware Version : ISP : Telmex fiber
I use this router to replace the FO rooter that my ISP provides with the service as it's too limited (no NAT name translation, closes NAT, no uPnP etc...)
So the WR841ND acts as my main router, DHCP server, WiFi AP for all my network. My problem is that once in a while ( every 1 or 2 days) the wireless loses functionality, I still can see it from my devices, but can't connect, even fixing the IP (apparently not a DHCP issue then). The only way to fix this is to shut down the router 10 sec and restart it.
This brings another issue, I have another router (WR741) in WDS dispatching the signal to another part of the house to wired devices (Xbox , wd tv live hub) and it loses the WDS link, again the only way for this router to recover it is to restart it which is annoying.
Region : UnitedStates Model : TL-WR841ND Hardware Version : V5 Firmware Version : ISP : charter cable
I am trying to install a HP officejet 6700 all-in-one wireless printer on my home network. I can see the MAC and static IP addresses in the ARP list but fail to connect to it via my laptop. I have disabled the Norton Internet Security smart firewall and the windows firewall and still fail to connect. I have spent 2 four hour chat sessions with HP and they tell me it is my router. They had me change the channel to 6 from 5 and 11g-only from the 11gb-mixed and it still does not connect. They also had me do a firmware upgrade but the Printer was up to date.
Region : Malaysia Model : TL-WR841ND Hardware Version : V8 Firmware Version : 3.12.9 Build 120221 Rel.31475n ISP : UNIFI Telekoms
I am doing port forwarding for 2 webservers i have IP Address is 192.168.0.2 and 192.168.0.4 Both have web apps running find within LAN, both run on port 80.Error code: 14004.
Region : Portugal Model : TL-WR841ND Hardware Version : V8 Firmware Version : ISP :
Yesterday I bought this router to extend my wifi signar from my cable router. Now I know that it is possible using the WR841ND as an wifi extender using third-party firmwares but what I like to know is if there is any way to make the router work like that but using the original firmware. I followed a guide that explained how to do it but the only thing I can do is extend the wireless signal without the internet acess.
Region : Others Model : TL-WR841ND Hardware Version : V8 Firmware Version : wr841nv8_en_3_13_27_up_boot(121101) ISP :
I followed TP-Link's guide to set up a WDS connection between my two brand new WR841ND router. It theoreticaly "works", but the network is extremly slow. Copying a ~100 Mb sized file to another computer on the other side takes more than 10 minutes or more, I don't know exactly, because I shut down the process after 10 min. I pinged the "slave" router with 200 packets, and I realized that every third, fourth and fifth packet has more than 500 ms time. The minimum is 4 ms, the longest was 566 ms.
Router A (Master) Connects to the internet/ADSL DHCP enabled
[Code].....
I bought the two router from the same dealer, at the same time. Both have the same firmware. I checked all the chanels, and 5 is the only free one, but the situation is the same on every chanel.
Region : Brazil Model : TL-WR841ND Hardware Version : V7 Firmware Version : 3.13.9 (Last) ISP : NET Virtua
I've bought a TL-WD841ND and was using it normally.
After I arrived from a trip, the internet speed by wireless and by cable is only 0,5~0,7 Mbps...
My internet connection is 10 Mbps, and if I plug direct on the modem, there comes the real speed (9,7 Mbps), but connecting by the router, the speed is 1/20 of what should be. Before my travel i was using it normal, and no one has changed any configuration.
So i've updated to the last firmware avaliable on the website. So i've rebooted it and the "configuration" LED keeps flashing...
I would like to know if this led flashing is normal: (here is a video that i've done: [URL] and what could be happening. ps: connecting by cable, the internet speed is also the same (even after the factory settings reset)...
Region : UnitedStates Model : TL-WR841ND Hardware Version : V8 Firmware Version : ISP : optimum online I have two wireless routers: TP Link TL-WR841ND and TP Link TL-WR541G
I would like to:
use the TL-WR541G for my children wireless laptop, wireless ipad and wireless iphones. I can turn this unit off at a specific time each evening as I wish.
The WR841ND is used for my wireless laptop, wired iMac, wired Roku stream player and wired Voip adapter.
I tried a few things but really do not know what I am doing and I cannot get both wireless routers to access the internet.
What I tried so far:
Cable modem ethernet out to the input on the WR841ND router. took one of the four hardwire outputs from the WR841ND and ran into the input on the WR541G I powered on the cable modem....it booted... i then powered each router up and waited for each to boot. I launched web browser and navigated to : http://192.168.0.1/ this allowed me to setup the WR841ND router.
it's current settings: Firmware Version: 3.13.27 Build 121101 Rel.38183n Hardware Version: WR841N v8 00000000 WAN type: dynamic IP LAN IP address: 192.168.0.1 subnet mask: 255.255.255.0 DHCP Server: enabled Start IP: 192.168.0.100 End IP: 192.168.0.199
How do I set up the second router? I tried to disable the DHCP server on router 2 (WR541g) and change the IP but don't know what to change it to.
Region : UnitedStates Model : TL-WR1043ND Hardware Version : Not Clear Firmware Version : ? ISP : Guadalupe Valley Telephone Company (TX)
I am a bit of a noobie and am considering buying a TL-WR1043ND router/access point, but I have read that this router will not connect directly to my ISP over DSL.I have fiber optic to my home from a local telephone company. Whether it will or will not act as the gateway to the Internet. If not, does it connect to another router that acts as a gateway to the Internet? Or what?Secondly, do you recommend this model which, considering features, appears to be good value at arount $50, but would like to know what others think about it.
Region : UnitedKingdom Model : TD-W8951ND Hardware Version : V5 Firmware Version : 22.05.2012 ISP :
I have a TD-W8951ND v5 on the latest firmware.
I recently broke my broadband data cap which surprised me as I had not been using the internet much.
I only have tablet which I switched off having first checked the router to make sure there were no other wireless connections and adding MAC address filtering to be sure no one else was stealing my bandwidth. With just my router connected to the ISP, my ISP has recorded 170MB of downloaded data in 3.5 hours. Switching off the router stops the traffic being recorded (as you would expect), but when switched back on the large data transfers start up again.
I have plugged in an older router (not wireless) and no traffic is generated, so it seems to be the TP-Link router rather than my ISP or ADSL circuit that is at fault.
I need a wireless router to transmit internet in my home, it's on two floors, my only concern is that the floor is really thick and I'm gonna be working in the basement. I need to choose between the following, can you tell me which is best?
I'm thinking of purchasing a Cisco Linksys EA6500. I need a router that can one monitor bandwidth used by device. Keep exceeding our ISP's network bandwidth allocation, need to identify the devices that are causing this high usage and be able to do so from the router. Does the EA6500's standard software support this, is their router software one can obtain for the unit that does this or is there another home router option that can perform this function?
Received this notice from ISP. Does this make sense:We have noticed we are getting a huge number of queries from X.X.X.X and it is showing to be about 98% of the DNS traffic hitting our name servers. It appears that the data consists of reverse lookups to 10.1.0.0 network. It needs to be remediated as soon as possible because it could cause a service interruption.It almost seems as if my router is acting as a DNS server. The isp data consists of reverse lookups to 10.1.0.0 network which would be the internal.
On my home network I have 11 devices connected.Is there a way I can give each device a certain bandwidth limit so my Internet doesn't keep getting sucked up?
i keep getting messages from AVG saying they have detected a very high internet usage, first it was with google and then with firefox..they recommended to shut down and restart..anyone could explain what's going on? I'm not downloadin anything..just checking my mail!
When a physical switchport/routed port has high usage, you can move the link to a higher capacity port, upgrade the port, bond links, etc. What exactly do you do when an SVI has high usage? I guess you could remove some servers from the VLAN, but that doesn't seem like a reasonable solution. What dictates the capacity of an SVI? The backplane of the switch?
Recently got a mobile broadband dongle for my laptop, shows 7.2 Mbps speed in the status window and under activity the received bytes is shooting up, as I write this is has went from 25,000,000 to 35,000,000, that's about 10 mg for a few seconds, it does this even when I have no page open, I can't see anything in task manager, I don't know why it's downloading so fast when there's nothing there, also because of this it is slowing my browsing down,
I have a 1841 router plugged into a 100M Comcast ethernet connection. My router cpu is really high and users download speed isn't as high as before. Can a 1841 handle 100M circuit with 100 users on it? What would cause the router's cpu to be high? I don't think there are any viruses or malware on the lan.
#sh proc cpu his r2.leaguecity-toy-startoy 06:06:26 PM Wednesday May 30 2012 PST 111 1 1 1 111 24 1 1 1 1 400369232222544222330359645223283294332688334452308404382236
I have a lot of cisco 7206 vxr deviceses. I have a high cpu problem.I have a 7206 vxr g2. I used to use ebgp for three upstream carrier. I used to bgp full route table method. I have about 800 Mbps active traffics and behing the router about 1600 active customers.
How can I trouble shoot this high cpu problem?
#sh int gigabitEthernet 0/1 GigabitEthernet0/1 is up, line protocol is up Hardware is MV64460 Internal MAC, address is 000c.cf1d.d01b (bia 000c.cf1d.d01b) Description: ***** GW Interface ***** [Code]....
I have a Cisco 1921 router and it uses 99% of CPU and i cant seem to spot wich process that is taking up the cpu. I have an interface with several sub-interfaces and i am moving data between two of those subnets, i tried the "ip route-cache same-interface"-command on giga bit ethernet 0/1 with all the sub-interfaces like gigabitethernet 0/1.18 and so on. That did not work.
My home network has two routers. My setup is...modem to router 1, then router 1 to router 2. is there a way to track the bandwidth usage on the two routers. My ISP says that I'm going over my bandwidth allowance and that's because in my household, we are hardcore gamers, netflix, and internet users. Router 2 belongs to my sister-in-law, and router 1 is mine. But I want to know which and more importantly, "WHO" is using more of the bandwidth.
We run a small school and one of our campus sites is quite remote and our internet provider chares big dollars for internet downloads.One of our classes has just been upgraded to run over the internet and involves downloading 6Gig of video each time it is run. This will cost us approximatly $15 for each student and we have hunreds of student. We provide computers for this course work.
I've got a problem with a core 6509E and the multicast.A client has a system with cams for the physical security and they are connected to a vlan with this config:
interface VlanXip address 172.20.167.1 255.255.255.128ip helper-address 172.20.32.7ip pim version 1ip pim sparse-modeendThe thing is that we know that one server that shows the cams at the security office is flooding the network and the CPU CORE is over 95% always:
CPU utilization for five seconds: 99%/39%; one minute: 99%; five minutes: 99% 263 644650276 567873287 1135 51.99% 55.06% 55.35% 0 IP Input [Code] ....
