Tp-link 300mbps Wireless :: Tl-wr1043nd No Vlan / Wifi Connection After Installing

Dec 9, 2012

Region : Netherlands
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version : V1_120405
ISP : UPC

After buying and installing i get no wlan/wifi connection.I do have internet by ethernet, the laptops and ipad sees the wlan/wifi but get no connection? Resetting re-installing manualy or with the wizard doesn't work.

View 2 Replies


ADVERTISEMENT

Tp-link 300mbps Wireless :: Tl-wr1043nd / Very Slow Connection (wired 57mbits / Wifi 4mbps)

Mar 27, 2013

Region : Belgium
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
ISP : Telenet

I've just bought a TP-Link TL_WR1043ND and when I was configuring the wireless settings first I had a +- 40Mbps connection,a little later the connection dropped to 4Mbps and was constantly dropping the speed.Sometimes it went to 15Mbps and then it drops back to 4Mbps.Right now its only 1Mbps.

Configuration:

Wireless channel: 11
Mode: 11bgn mixed
Channel width: Auto
Max tx rate: 300Mbps
Wireless router radio and SSID broadcasting enabled

[code].....

View 1 Replies View Related

Tp-link 300mbps Wireless :: Tl-wr1043nd Possible To Connect Two Routers Through Wifi

Mar 1, 2013

Region : Canada
Model : TL-WR1043ND
Hardware Version : V1

I was wondering if it is possible to connect two routers through wireless and make them talk to each other. Here is why I need it, I currently Have 6 wireless IP Cameras going too 8. 2 are wired on one router in my house and the other 4 are wireless(with wired capabilities) Im going to wire the other 4 too a 2nd router so the cameras are always running and don't suffer any down time due to signal loss (happening a lot at the moment). How can I get Router B to talk to Router A, so I can look at all of the cameras from Laptop in my house which is closer to Router A.

My Router A is TL-WR1043ND, I'm also going to probably buy another one. How to configure it properly. So I can login to the cameras from my laptop.

View 1 Replies View Related

TP-Link 300Mbps Wireless :: TL-WR1043ND WAN Connection Seems To Be Dropping

Dec 5, 2012

Region : Argentina
Model : TL-WR1043ND
Hardware Version : v1
Region : Canada

I have a T L-WR1043ND v1.9 with the latest factory firmware that I recently purchased. Ran fine for a couple of weeks. Now my WAN connection seems to be dropping. I get an IP and DNS from the ISP but I cannot ping anything (google etc...) past the router. I have to hit the detect button or release and renew the IP in order to gain access. Then after a few hours or a day the issue reoccurs.

View 1 Replies View Related

Tp-link 300mbps Wireless :: Tl-wr1043nd Password Protection Of Wifi Doesn't Work

Apr 11, 2013

Region : Netherlands
Model : TL-WR1043ND
Hardware Version : Not Clear
Firmware Version :

I installed my brand new TP-Link router and both wired and wireless internet connection work perfectly fine. But when I tried to secure the wifi with a password (I followed the instructions on last page of installation guide) I can not connect to the internet any more. After entering the correct password, both iphone and mac-book simply say "unable to join the network". I selected WPA2-PSK-personal as recommended. For now I switched off the security settings, but I live in a building with many neighbours and they are now consuming most of my bandwidth (apparentlyI am surrounded by illegal downloaders

View 2 Replies View Related

Tp-link 300mbps Wireless :: Tl-wr1043nd / Wifi Shows Good Signal But No Internet?

Apr 18, 2013

Region : UnitedStates
Model : TL-WR1043ND
Hardware Version : Not Clear
Firmware Version :
ISP : HughesNet

I received this router today, I have a MacBook Pro and a iPhone. The router came with a very small cd, I was very disappointed because , when I purchased this router from amazon , the discription read that this router is Mac compatiable. But that is not true if the cd is not compatiable! My problem is I get a good signal for wifi, but I can not open any websites with my Mac or my iphone.

View 1 Replies View Related

Tp-link 300mbps Wireless :: Tl-wr1043nd - Wifi Connected Tp Wds Bridge Loses Its Settings

Dec 17, 2012

Region : Others
Model : TL-WR1043ND
Hardware Version : Not Clear
Firmware Version :
ISP :

I have 2 TP-Link # 941NDs at my home. ( version 3.6 )In the new ( second ) TP link, i activate WDS - Wireless Bridge. And configure it to through Wi-Fi connect with earlier TP-Link, and also to act as router to cater to PCs within its range. IPs are set as per of same family as that of primary TP-Link, and further, DHCP been de-activated as well. Have sent WEP security as well.It performs correctly for the time, its stays ON, but when its switched Off, and then On again, it is not able to connect to the primary TP-Link and thus not able to serve its client PCs.

View 4 Replies View Related

TP-Link 300Mbps Wireless :: Slow Connection With TL-WR1043ND Router

Apr 24, 2013

Region : Malaysia
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.13 Build 120605 Rel.38634n

The connection is slow when I connect my notebook to the TP-Link TL-WR1043ND wireless router. If I connect my notebook directly to to the ISP modem, the connection speed back to normal.

View 1 Replies View Related

TP-Link 300Mbps Wireless :: TL-WR1043ND / Connection Drops Out Randomly

Jan 19, 2013

Region : Austria
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.4 Build 110429 Rel.36959n
ISP : TPG

I've got a problem with the wireless dropping out randomly. It may take a week before it stops or a couple of hours. I originally thought my microwave oven was swamping the signal when we used it so I relocated the router much further away but this hasn't changed anything. I can still log in to the router from a computer on the wired ports and reboot the router. It also thinks the wireless is working but everything looses connection to it. We have 3 laptops and 4 phones that use the wireless and they all cannot connect when it goes down. This is only a new device - less than 6 months?

View 5 Replies View Related

TP-Link 300Mbps Wireless :: TL-WR1043ND - Router Looses Connection To WAN?

Mar 1, 2013

Region : UnitedStates
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
ISP : AT&T

Every 5 to 7 days my router loses connection with WAN (ISP modem) but connection over LAN is fine. It seems that 1043ND tries to connect to DSL modem from AT&T by username and password (that does not exists) instead of doing Dynamic IP. I understand that AT&T modem is of type of PPPoE but there is not a password or user id and connection must be dynamic. Page 192.168.0.1/logininfo of modem complains that I was trying to login with incorrect user id password. Every time I have to

1- connect the modem directly to my computer so the modem resets.

2- I have to reset 1043ND to factory default, reboot, and connect cables back how they were, Then go to WAN page do a release and renew to get connected to WAN again.

View 2 Replies View Related

TP-Link 300Mbps Wireless :: TL-WR1043ND Printer Connection Via TCP / IP Port

Feb 7, 2013

Region : Germany
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 121127

is it possible to use the Print Server on the TL-WR1043ND without installing the "Printer Controller Utility"? I have a HP LaserJet 1022 (in compatiblity list) connected which is recognized by the TL-WR1043ND. I want to connect the printer manually to my Windows PC using standard tcp/ip port, but I can't get it working. I tried RAW with Port 9100 and LPR with lp1. What are the right settings??

View 1 Replies View Related

Tp-link 300mbps Wireless :: Tl-wr1043nd - Usb Printer Controller Utility (Wifi Disconnects With On / Off Sound)

Feb 17, 2013

Region : Romania
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : latest
ISP : RDS

I am experiencing an issue since I bought my new laptop.I connect to the Internet with Windows 8 and TL-WR1043ND.My issue is that ever since I installed the printer utility from the site I hear an ON/OFF sound in my speaker randomly and I can not figure out what`s wrong.I think it`s trying to search for my printer but it it off.Also wi-fi disconnects randomly ever since this application was installed.What can I do to fix this issue.Computer works fine without the application.There is no report about this issue in the Event Viewer.

View 4 Replies View Related

TP-Link 300Mbps Wireless :: Can't Get SKY Digital To Connect To TL-WR1043ND Via Ethernet Connection

Nov 18, 2012

I've recently bought a TL-WR1043ND & i'm trying to connect my Sky+ box to the Internet. When I connect the box directly to my broadband router all works OK. When I connect via an Ethernet connection on my TP-Link router - it get's an IP address from the router but it will not connect to the internet.

View 4 Replies View Related

TP-Link 300Mbps Wireless :: TL-WR1043ND - Slow Internet Connection Via Router

Apr 14, 2013

Region : Argentina
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version :
ISP :

Region : Netherlands
Model : TL-WR941ND
Hardware Version : V3
Firmware Version : 3.13.9 Build 120201 Rel.54965n
ISP : Ziggo

I currently have a issue with my TP-link WR941N.When I first connected the router I had a good internet speeds of about 70 mbps. My max provided by the ISP is 120Mbps but 70 was acceptable for me. Recently however the connection is terrible. I regularly have a speeds of 6Mbps via the router, When i directly to the modem via kabel I get a speed of 120Mbps. Therefore I ruled out that the connectivity problem is due to my ISP.

View 1 Replies View Related

TP-Link 300Mbps Wireless :: Create Firmware For Hard Drive 4 TB Connection To Router TL-WR1043ND Via USB

Jan 16, 2013

Region : Russia
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12 Build 120405 Rel.33996n

can You create firmware for Hardrive 4 TB connection to router TL-WR1043ND via USB.

View 2 Replies View Related

TP-Link 300Mbps Wireless :: WR1043ND V1.9 Not Seeing A WD 3TB USB NTFS HDD?

Dec 21, 2012

Region : Argentina
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version :
ISP :

Region : Argentina
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
ISP :

I have a WR1043ND

Firmware Version:
3.13.12 Build 120405 Rel.33996n
Hardware Version:
WR1043ND v1 00000000

I tried to connect a WD MyBook Essential 3tb hdd NTFS, but it never recognized it. Of course, I connected it with the external power supply.With a 15gb pendrive FAT32 it works OK.

View 14 Replies View Related

TP-Link 300Mbps Wireless :: WR1043ND Very Low Upstream?

Nov 26, 2012

Region : Russia
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version :
ISP :

Region : Russia
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version : wr1043nv1_ru_3_13_10_up(120614)
ISP : netbynet

Connection to a router on a cable speed of dowstream-50MBit/s, upstream-3Kbit(!) wifi-dowstream-50MBit/s, upstream-3KbitA cable directly in the personal computer to 70 Mbps there and back.Measured speedtest.net, and as [URL] The matter is that even elementary with an investment it is impossible to send mail - I am connected by different devices-2 of the laptop and 2 smartphones - the same. Technical support of provider already talk sense only in a router. Insertions updated, changed - the same( Firewalls are disconnected, any more don't know what to do and where proceeding speed and all digs-is killed. Russian forum TP-Link is idle.

View 3 Replies View Related

TP-Link 300Mbps Wireless :: TL-WR1043ND How To Get Device Pin

Dec 26, 2012

Region : Austria
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version :

unfortunately I've lost my device pin and I've reset my device.can I get the device pin on a other way? on my invoice there is no information about that.

View 1 Replies View Related

TP-Link 300Mbps Wireless :: VPN Usage On TL-WR1043ND Without DD-WRT?

Jan 22, 2013

Region : Netherlands
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
ISP :

Is it possible to use a VPN service such as hidemyass on the TL-WR1043ND without installing the DD-WRT firmware?

View 2 Replies View Related

TP-Link 300Mbps Wireless :: Why To Install CFW On Wr1043nd

Jan 25, 2013

Region : Argentina
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12

I just got one of these to replace my old wrt54g. Seems to me a lot of people are flashing theirs with dd-wrt or openwrt. I was wondering why exactly. Unlike the old wrt54g, the tp-link stock firmware supports a lot of features in my view, especially the so wanted QOS. Do the CFW give the wr1043nd more stability or maybe better performance? Or is it about features? What features a CFW would add to the stock fw?

View 2 Replies View Related

TP-Link 300Mbps Wireless :: Using TL-WR1043ND As A Switch?

Dec 24, 2012

Region : UnitedKingdom
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version :
ISP :

My house has thick internal walls, so WiFi does not propagate easily. I am fortunate to have FTTP. Therefore I have the following setup: At one end of the house there is a Genexis HRG1000 Fibre Optic Modem / Router with WiFi and 4 ethernet ports. One of its ethernet ports links to a Devolo 200Mb homeplug and there is a matching homeplug at the other end of the house which is linked to a WR1043ND. We have tried two configurations each with various settings. If we link into the WAN port it creates a separate network which cannot be seen from the fibre modem end (since the 196.168.1.n addresses are non-routing) and although this works, we cannot stream / transfer files from the PC (connected to the fibre modem by ethernet) to the smart TV connected to the WR1043ND. The TV can "see" the internet and things like iPlayer work. Various other gadgets can connect either by ethernet or WiFi and get successful internet access. Alternatively If we link into one of the LAN ports, AND disable both the DNS service and the DHCP server in the WR1043ND it all appears as one network, but although it is disabled, all the gadgets and computers try to use the DNS in the WR1043ND rather than that in the fibre modem and consequently there is no internet connectivity. We have tried several combinations of fixed and dynamic IP addresses, rebooting the WR1043ND and the PC etc. but nothing seems to work. What does work is giving both WiFi routers the same SID and password so that moving from one part of the house to another with, say, a smart phone transfers what connectivity there is seamlessly.

View 3 Replies View Related

TP-Link 300Mbps Wireless :: TL-WR1043ND Disconnects Every Two Days?

Mar 19, 2013

TL-WR1043ND disconnects every two days

View 7 Replies View Related

TP-Link 300Mbps Wireless :: TL-WR1043ND - USB Hub With Multiple Printers?

Jan 9, 2013

Region : Others
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version :
ISP :

I got a TL-WR842ND to try and decide if i want to buy it. I want to connect a usb hub with 5 printers connected to that hub and use it as print server, would that work at all?

View 2 Replies View Related

TP-Link 300Mbps Wireless :: Use TL-WR1043ND USB Printer For IDevices?

Apr 9, 2013

Region : Germany
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version :
ISP :

my new TL-WR1043ND. I've just installed the usb print driver for my HP PSC 2355 and it works fine for the PCs.Currently i'm wondering if i have any chance to also print using my iDevices (iPhone & iPad) in an AirPrint like way? The devices are connected via WiFi.

View 2 Replies View Related

TP-Link 300Mbps Wireless :: TL-WR1043ND - Way To Forward Port For NAS

Apr 10, 2013

Region : UnitedKingdom
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 1.4.0 Build 111130 Rel.55990n
ISP : Titanadsl

My router is a TD W8960N v3 which isn't listed here.I've connected a Synology 110j to the router and need to sort out the port forwarding which I'm not much good at. I am finding the TP Link documentation. I did find the page on DMZ but I don't know what that is.

View 4 Replies View Related

TP-Link 300Mbps Wireless :: Connecting To Internet With TL-WR1043ND

Apr 26, 2013

Region : Argentina
Model : TL-WR1043ND
Hardware Version : V1

I own a TL-WR1043ND. Until recently it has been working like clock work but after a power cut it seems to have lost its settings. Currently there is a WiFi network: both my iMac and my MacBook Pro manage to create a network between them and i can access / transfer files from one to the other without any problems what so ever. My Gmail app on my iPhone also updates emails on this same network. But when i try to browse the web on both Safari or Firefox or check my email on Mail (OSX email client) I am not being allowed to do so. Its as though there is not internet connection. The same thing is happening to my wife when she is using her Nexus 7.

Unfortunately i have lost my DVD with the setup files and I am there for not managing to access the settings of the router. I have tried searching the web to find the downloadable software but it turns out the only ones that i found are for Windows only.The only way to access the web and update my emails etc is when i connect to the modem via Ethernet cable.

View 1 Replies View Related

TP-Link 300Mbps Wireless :: Comcast May Have Destroyed TL-WR1043ND

Mar 28, 2013

Region : UnitedStates
Model : TL-WR1043ND
Hardware Version : V1
ISP : Comcast

I'm sort of used to everything failing every 2 days when a new device shows up due to the DHCP timeout issue that I've posted a workaround to. However, after rebooting everything, NOTHING worked. At all.I could get to the Admin page too.The DHCP address to my Comcast modem was 0.0.0.0 etc.The TP-Link "Detect" feature started saying Comcast was issuing me a "Static IP" instead of "Dynamic".Now, I can get an address from the Modem to my PC.So I cloned the PC's MAC ID.If I reboot the TP-Link 5 or 6 times, it might pick up the Comcast IP once, but no routing happens to the internet.I did try putting the static IP address into the TP-Link to see if I could fake it into getting online temporarily, but no.

And... after hours of troubleshooting last night, the router will not hand out DHCP addressed to any LAN equipment any longer either.Even, if I plugged in my laptop (which worked on the Comcast modem), the IP address it received from the TP-Link was the Comcast Public IP!Not a NATed / DHCP IP address! so I Factory Reset the TP-Link via the Admin page AND via a paper clip at least 4x.There were also no thunderstorms. Both the router and the modem are on a UPS / surge protector.The house is not (usually) haunted.I did try the new Beta firmware but that didn't fix anything.I also "upgraded" to DD-WRT.

View 5 Replies View Related

TP-Link 300Mbps Wireless :: Update The Firmware WR1043ND?

Feb 14, 2013

Region : Argentina
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version :
ISP :

Do not we deserve, (their customers), at least bothered to tell us?

View 14 Replies View Related

TP-Link 300Mbps Wireless :: TL-WR1043ND Disconnects Every Two Days?

Mar 18, 2013

Region : UnitedStates
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12 Build 121210 Rel.73912n (Beta)
ISP :

I have tried to go through the tech support email but no dice. My router disconnects every two days. The sys light will stay solid and require a reboot and my computer connected to the router will be unaffected . I have a 30mb connection with only 2-3 wireless clients on at the same time as the wired. The response I got from tech support email after waiting almost a week without a response was :

Because there's not much we can do to fix the problem right now and TL-WR1042ND is more competent for your network, I suggest you to change for it.

If you still don't wanna change for TL-WR1042ND, change for a new TL-WR1043ND to have a try."

This is answer I get after already asking once why they want me to downgrade for a different router . What exactly the TL-WR1042ND is going to do for me that the one I have won't,but I cannot get a answer.I have no idea what they mean by "competent ", I don't believe my network is anything special and see no reason why the problem would be fixed by downgrading . This is the second router since December I have had and really dont feel like paying another 15$ shipping back to newegg for a refund.

View 1 Replies View Related

TP-Link 300Mbps Wireless :: Cannot Connect Via PPTP VPN On WR1043nd

Mar 23, 2013

Region : UnitedKingdom
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
ISP : Plusnet

I'm on a fibre connection from Plusnet and bought the TL-WR1043ND because of the advertised ability to use PPTP VPN to connect to my work server (the supplied Plusnet router doesn't allow it and is locked down).However, I cannot connect via PPTP VPN on this TL router either. I know my VPN settings are correct and I have had a brief search and found others have this problem, but short of installing third party firmware on the router, how to get this router running my PPTP VPN?

View 1 Replies View Related

TP-Link 300Mbps Wireless :: New Firmware TL-WR1043nd Not Working

Apr 12, 2013

Region : Argentina
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : TL-WR1043ND_V1_130325
ISP : Ip dinamics

It worked correctly 2 days and 16 hours.Now, does not surfing in internet.although I can go to web interfaceI turn the gargoyle.The developers of TP-Link me tired

View 9 Replies View Related

TP-Link 300Mbps Wireless :: WR1043ND Usage As Gateway

Dec 2, 2012

Region : UnitedStates
Model : TL-WR1043ND
Hardware Version : Not Clear
Firmware Version : ?
ISP : Guadalupe Valley Telephone Company (TX)

I am a bit of a noobie and am considering buying a TL-WR1043ND router/access point, but I have read that this router will not connect directly to my ISP over DSL.I have fiber optic to my home from a local telephone company. Whether it will or will not act as the gateway to the Internet. If not, does it connect to another router that acts as a gateway to the Internet? Or what?Secondly, do you recommend this model which, considering features, appears to be good value at arount $50, but would like to know what others think about it.

View 1 Replies View Related

TP-Link 300Mbps Wireless :: TL-WR1043ND Unable To Receive Dynamic IP

Nov 26, 2012

Region : Sweden
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version : TL-WR1043ND_V1_120405_
ISP : Tele2 (fiber)

I recently bought your router and I am trying to install it.The problem that I get is that when the router tries to get the dynamic IP from my provider, it gets nothing.I have typed in the DNS servers but no go. Without the router, my uplink works fine. The provider does not lock onto a specific MAC adress.

View 8 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved