Cisco Routers :: Configuring RV220w With Bridged Modem?
Mar 8, 2012
I'm having trouble getting my RV220W router to work with a DSL modem. I pre-configured the device and shipped it to one of our store locations. I came to find out that the site had an "Advanced" modem (according to the carrier) and I had to have them "bridge" the modem. Prior to having the modem "bridged" I was able to have the user plug the RV220W into the modem, and the computer that was hard-wired to the router was pulling the correct set of IP addresses, however, my VPN tunnel was not working because the WAN address that the RV220W was receiving was 192.168.2.12 instead of the staticly assigned IP address from the ISP After bridging the modem, the user is able to access the RV220W but he does not have internet connectivity. According to the carrier, this is because we need to enter their PPOE username and password into the RV220W. My only problem is that my on-site person is not very technical, and although I have access to one of our other sites with a working RV220W I'm not able to find where I enter this PPPOE information into the device. get this thing setup so that the customer is able to get connected to the internet, and that my RV220W is pulling the correct staticly assigned IP address from the ISP?
View 5 Replies
ADVERTISEMENT
Oct 15, 2012
I am working overseas for a small company, trying to get an RV120 VPN router to connect to our network back home. Part of the problem is that I have to use a DSL modem here which is also a router, and so the WAN IP given to the modem is not the same one used by the VPN router.
Do we need to create a bridge between the two routers so that the VPN router can use the WAN IP from the ISP instead of a DHCP address on the local network? Or is this the wrong approach?
View 3 Replies
View Related
Aug 5, 2012
i've just purchased cisco rv042. i want to connect to my ISP using modem (bridged). i tried to config pppoE on the router with my isp acount and connecting it to the modem. the issue is my router doesnt get any ip from the modem(aztech tnn 600e).
* the dhcp on the modem is working properly. i checked by connecting a computer to it, the ip was assigned. and another test i did, i connected the rv042 on "assign ip automatically and it got ip from the modem (worked well when the modem is bridged ot bridged).
View 15 Replies
View Related
Mar 29, 2013
Region : UnitedStates
Model : TL-WR841ND
Hardware Version : V8
Firmware Version :
ISP : optimum online
I have two wireless routers:
TP Link TL-WR841ND
and
TP Link TL-WR541G
I would like to:
use the TL-WR541G for my children wireless laptop, wireless ipad and wireless iphones.
I can turn this unit off at a specific time each evening as I wish.
The WR841ND is used for my wireless laptop, wired iMac, wired Roku stream player and wired Voip adapter.
I tried a few things but really do not know what I am doing and I cannot get both wireless routers to access the internet.
What I tried so far:
Cable modem ethernet out to the input on the WR841ND router. took one of the four hardwire outputs from the WR841ND and ran into the input on the WR541G I powered on the cable modem....it booted... i then powered each router up and waited for each to boot. I launched web browser and navigated to : http://192.168.0.1/ this allowed me to setup the WR841ND router.
it's current settings:
Firmware Version: 3.13.27 Build 121101 Rel.38183n
Hardware Version: WR841N v8 00000000
WAN type: dynamic IP
LAN IP address: 192.168.0.1
subnet mask: 255.255.255.0
DHCP Server: enabled
Start IP: 192.168.0.100
End IP: 192.168.0.199
How do I set up the second router? I tried to disable the DHCP server on router 2 (WR541g) and change the IP but don't know what to change it to.
View 3 Replies
View Related
Aug 19, 2011
I have a Speedstream 4300 modem in bridge mode and a linksys WRT54G2 router set to PPPoE like I was instructed. On the status page of my router underneath the PPPoE setting it has IP, Subnet Mask, and Gateway all set to 0. The only advice I was able to obrain from my ISP was to powercycle the router and modem, which I did and no change.
View 1 Replies
View Related
Feb 19, 2012
We got a 1921 router that works fine. We ordered Verizon Businss One Static IP ADSL. It came with a Westell Modem that we configured in bridge mode. When we do a test by assigning a static IP to our laptop then hook it up to the Westell it works fine. We can browse the web. Then when we assign a static IP to the Ethernet on our 1921 then connect it to the Westell it doesn't work. We can't ping out from the router to for example 4.2.2.2. From the router we can't even ping the default gateway (on Verizon's side).
View 2 Replies
View Related
Nov 8, 2012
Using Cisco 1811W with IOS 15.1(4)M5. FE0 and FE1 are connected to the internet via Billion ADSL2+ modems operating in bridged mode. Both lines are similar so I'll only discuss FE0 from this point on.Local subnet is 192.168.128.0/24 with router on 192.168.128.1 as default gateway. Modem on FE0 has static LAN IP of 192.168.128.2 and when plugged into the switch on the LAN side, the web interface can be accessed at that IP address. Unplug the modem from the switch and plug it into FE0 and it now works as desired providing access from the router to the internet but the web interface is no longer accessable at 192.168.128.2
I tried adding a static route "ip route 192.168.128.2 255.255.255.255 FastEthernet 0" and also "ip route 192.168.128.2 255.255.255.255 Dialer 1" Neither worked and presumably it isn't that straight forward. Possibly NAT or other routing configuration required.Although there isn't much to configure when in bridged mode, I mostly want this setup so I can look at the ADSL connection status and for the modem to write messages to syslog (works when plugged into switch on LAN side), or SNMP access.
View 3 Replies
View Related
Feb 6, 2012
I'm trying to connect my Xbox 360 to Live by bridging my computer's wireless connection. I've done this before for a friend in a different city and it worked fine, and I felt very proud of myself for doing so. However when I try to connect here, the modem won't assign my Xbox an IP address. I've been into ipconfig/all and tried to manually assign the same IP address to the Xbox but to no avail. Same deal with the alternate MAC address option.
To speed things along here's the readout from my ipconfig/all:
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersSamsung>ipconfig/all
[Code].....
View 2 Replies
View Related
Feb 26, 2012
I'm trying to connect my WAG160N as a ADSL modem (disable the router function) and connect a real router (RVS4000)So, i put my WAG160N on birdged mode only, disable the DHCP on my RVS4000, i did configure my PPPOE access (user and password), change the IP adress 192.168.0.2.configure the DHCP and try to connect. i tryed to connect the RVS4000 and the WAG160N either with cross cable or a direct cable. I can get access to the RVS4000 192.168.0.2 and get access to the configuration menu but cannot get access to my WAG160N 192.168.0.1 even a simple ping.when i try to test the connection on my RVS4000 (status) it seems that my connection is up but i cannot get access to internet.
View 6 Replies
View Related
Jun 5, 2012
I've a Cisco SRP527W, it have a LAN in 192.168.1.0 range, now I need to put in bridge mode, to be transparent with my firewall, how can I do this?
View 3 Replies
View Related
Aug 21, 2012
configuring 2620 cisco to cable modem for internet.I'm setting up a lab to practice and am having trouble getting this to work.Made several configs that don't work and starting over form scratch.
View 3 Replies
View Related
Jun 5, 2012
I have a Cisco 881G with PCEX-HSPA-3G card for which I have successfully configured for internet. As the above one has come to end of life, we got the replacement 881G with embedded 3G modem.
I can't get Cellular 0 to use ppp encapsulation:
Router(config-if)#encapsulation ppp
Cellular0: Only SLIP encapsulation supported
Router(config-if)#
[Code].....
View 9 Replies
View Related
Nov 20, 2012
I have a cisco 1941 ISR router and I am trying to configure a router to allow a modem for "Offband or Out of band" access.Below is the configuration on Aux port on Line (n):
line aux 0
login local
modem InOut
transport input all
speed 115200
flowcontrol hardware
I have US Robotics 56k Faxmodem which is connected to aux port of router and I am using USB dialup modem with my laptop to dailin to the router which is connected to a US Robotics Faxmodem. Then I have accessed my USB dialup modem throught HyperTerminal and I can issue all "at" commands and to dialin to the modem I have used the following command atdt914011111111 (atdt followed by country code, area code and landline number)Once I issue the above command it give me message "Connected" and after this I just get a flashing cursor. I cannot do anything nor will it display a username login prompt.
View 1 Replies
View Related
May 15, 2013
I've struggled now for a couple of days to setup a PPPoe connection on our cisco 887va box. I can setup straight away on a draytek box so i know the connection is good.I can't get the line protocol to come up? It's connected via ethernet port 0 to an external modem. One thing i can't figure out is if ethernet 0 and fast ethernet 0 is the same physical port?I've attached the running-config below.
Building configuration...
Current configuration : 3738 bytes!! Last configuration change at 16:16:56 UTC Thu May 16 2013version 15.2no service padservice timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname **!boot-start-markerboot-end-marker!!no logging bufferedno logging consoleenable secret *************
enable password ***********!no aaa new-modelmemory-size iomem 10!crypto pki trustpoint TP-self-signed-15463827enrollment selfsignedsubject-name cn=IOS-Self-Signed-Certificate-15463827revocation-check nonersakeypair TP-self-signed-15463827!!crypto pki certificate chain TP-self-signed-15463827certificate self-signed 01 **** quit!!!!!!ip cefno ipv6 cef!!license udi pid ***************!!username ************** privilege 15 password 0 *****************!!!!!controller VDSL 0operating mode vdsl2!csdb tcp synwait-time 30csdb tcp idle-time 3600csdb tcp finwait-time 5csdb tcp reassembly max-memory 1024csdb tcp reassembly max-queue-length 16csdb udp idle-time 30csdb icmp idle-time 10csdb session max-session 65535!!!!!!!!!interface Ethernet0description
[code]....
View 10 Replies
View Related
Feb 8, 2012
I am using a broadband internet of a provider named BSNL,through a simple modem. Recently I got a Beetel 450BX1 ADSL2 + Router and want to use the wireless capability of the laptop so that I don't have to be glued to my table. The OS I'm using is Windows 7 Ultimate (32 bit) on an HP Compaq 6515b.I configured the modem by following the instructions in the following link url...I believe that's a straightforward method for configuring a router, and that accomplishing this is very simple.I followed the steps, only changed the username and password to that given by BSNL.Then, finally I unplugged the LAN cable and clicked on Connect to <connection name>, punched in the serial key. But it does not connect and says "Windows was unable to connect". Even after using Windows Network Troubleshooter the problem is not solved.
View 4 Replies
View Related
Nov 20, 2012
I have a cisco 1941 ISR router and I am trying to configure a router to allow a modem for Offband or Out of band access.Below is the configuration on Aux port on Line (n): [code] I have US Robotics 56k Faxmodem which is connected to aux port of router and I am using USB dialup modem with my laptop to dailin to the router which is connected to a US Robotics Faxmodem. Then I have accessed my USB dialup modem throught HyperTerminal and I can issue all at commands and to dialin to the modem I have used the following commandatdt91401111 1111 (atdt followed by country code, area code and landline number)Once I issue the above command it give me message Connected and after this I just get a flashing cursor. I cannot do anything nor will it display a username login prompt.
View 1 Replies
View Related
Apr 2, 2012
what exactly is QuickVPN?Is it a IPSec VPN?Is it a PPTP?Is it a SSLVPN?can I resolve my local hostnames? That means, can I configure a lokal DNS Server?
View 3 Replies
View Related
Aug 24, 2012
I am trying to setup and configure a VPN on the RV220W that uses IPSEC so I can use the Cisco VPN Client I use at work, I have gone through the user manual 11 or 12 times now but still cannot work it out. I cannot find where on the Rv200W iset up the phase 1 authentication username and password which will then lead me onto the phase 2 stage of asking for a username password to allow me access.
View 8 Replies
View Related
Jul 3, 2012
Picked up a pair of RV220W's for a project I'm working on. I have several IP's available, 4 of which are assigned to/in use by a server behind the RV220W. All 4 of these IP's are static external IPs. How I can configure the RV220W so that requests to those 4 IP's get routed to the server.
Prior to purchasing this, I was under the impression what I was trying to do was called one-to-one NAT, but after reading the 'Help' document on the one-to-one NAT page, I don't think this is right. Emphasis added below: Cisco RV220W Wireless-N Network Security Firewall Help FirewallOne-to-One NATOne-to-one NAT is a way to make systems behind a firewall and configured with private IP addresses appear to have public IP addresses.One-to-One-NAT Rule TableThis table lists the list of available One-To-One NAT rules configured by the user. Private Range Begin: start ip address in private (LAN) ip addressPublic Range Begin: start ip address in the public ip address (WAN IP), Public IP Subnet Mask: The Subnet Mask of the public IPRange Length: Range length maps one to one private address to public address up to the given range.Service: This column shows service to be accepted by LAN Host.The actions that can be taken on One-to-One-NAT rules are:(Check Box At First Column Header): Selects all the entries in the table.Add: Opens the One-To-One NAT Configuration page, to add a new entry. Edit: Opens the One-To-One NAT Configuration page, to edit the selected entry.Delete: Deletes the selected entries.
So according to their documentation, the server in question would need to be configured with a private IP. Unfortunately, one of the applications I use is licensed via IP address and my understanding is that I cannot use the software with private/non-routable IP addresses.
Is the RV220W capable of not only securing the line (firewall, access rules, content filtering, port trigering & forwarding etc) but also doing what I was hoping to do (keeping the external IP's on the server, and routing appropriately)?
View 9 Replies
View Related
May 15, 2012
I'm using a RV220W router, and recently got shifted to a dynamic IP solution.Now, I've got a no-ip.org address, but the update service seems to be on no-ip.com. So, I try to enter mydomain.no-ip.org OR mydomain.no-ip.com in the dynamic dns settings, under Host and Domain Name, but when saving the settings it says
'The hostname specified does not exist in this user account' ,which seems to indicate that it manages to login to the update service but gets a negative reply.Is it possible to use the RV220W with no-ip.org/com?
View 5 Replies
View Related
Dec 12, 2012
We have 2 sites connected thru 2 RV220W routers via VPN and most things are working fine. I have noticed however, that any device that has a web interface, i.e. our Sharp Copier and our Freenas server, is inaccessible. The page tries to come up but then I get the Cisco "server is down" page generated by the RV220W.
I can pull up the web interface pages if I use a machine on the local LAN but not on any machine across the VPN. The only commonality I can think of is the RV220W blocking that traffic for some reason..
View 8 Replies
View Related
Sep 28, 2011
Cisco support write down manual (workaround), how to setup IPsec VPN connection on Mac OS 1.7?
View 5 Replies
View Related
Nov 27, 2011
Is there anyway to associate a name to an IP in the RV220W? I am coming from a WRVS4400N v2. Folks are complaining that they can't connect, for example via Real VNC, via the PC name any longer. They have to use the IP address. In the past I put the names of the PCs in the WRVS4400N when I reserved IPs via MAC addresses (some call this assigning static IPs). There isn't any place in the RV220W to put the name. Even when I look at the DHCP list a lot of them show up as "unknown". I am sure this is a NETBIOS thing but I'd rather fix this in the router as I have always done in the past.
View 4 Replies
View Related
Jul 22, 2011
i have a RV220W and absolutely nothings functional on this stupid Router, no NAT , no Port Forwarding and I cant access my Network from Outside. Any firmware link for downloading. This address works, its handling special webrequest.
View 1 Replies
View Related
Jul 19, 2012
I set up a PPTP VPN with an RV220W recently. It was working flawlessly until a recent power outage and now users are getting the 807 error when attempting to connect. I have PPTP passthrough enabled and TCP/UDP 1723 open. As far as I can tell GRE 47 is open as well. Why it was working and is not working after a power outage?
View 2 Replies
View Related
Jun 23, 2012
Having a strange problem that just started this week and got worse this evening. I have a RV220W that is feeding my network. The RV220W sits behind a broadband modem and acts as the DHCP for the network and those computers access the internet that way. Anyway, tonight started an issue where the the RV220W just disappears. Becomes unpingable. I recycle power, and within anywhere from 5 to 10 minutes, it's gone. No longer pingable. Even if I plug a latop directly into it.If I power cycle the RV220W it comes back and I can ping it and access it and its settings. 5 to 10 mins later, I again lose it. Nothing was done. Its been working fine for a few weeks. Had a similar outage last Tuesday, but a recycle of everything brought everything back into line. After I lose connection to it, the lights I expect to be lit remain lit.
View 1 Replies
View Related
Jan 26, 2012
I am unable to make UPnP to work on the RV220W. I am forced to use port forwarding.
View 10 Replies
View Related
Nov 20, 2012
Nothing happens when clicking the SAVE button after making changes on the VLAN Membership screen when using IE9, but it work fine with IE8. Any problems using IE9 during configuration?
View 4 Replies
View Related
Jan 31, 2013
When someone downloads a file, or similar, there seems to be no, or very little, room for other requests. I've even tried to be the only one on the network, start a download (from ex. Intel) and then tries to access a simple website, almost only text, and its extreemly slow. I hav ethe latest firmware, a windows domain network and the routers is not acting as dhcp server.
View 4 Replies
View Related
Sep 26, 2011
Where I can find the MIB files for RV220W router?
View 2 Replies
View Related
Aug 5, 2011
I'm an IT professional with more than 10 years experience. I have spent last 5 days trying to figure out why the wifi connection to this router is so slow, but still no luck. I'm getting only 13Mbps even if my laptop is next to the router! (wired connection worked ok)
I have tried all sort of setting combinations, 2.4GHz/5GHz; N only/ G,N Mixed; Auto/20MHz bandwidth; different channels; WPA2 encrypted vs open; disable firewall; wmm enabled/disabled; 1.0.0.26/1.0.1.0 firmware... no matter what I try, I always get only 10 - 15Mbps speed.
Once I replace this router with my old router, it worked perfectly --- getting 70 - 80Mbps with exactly the same testing environment and configuration.
I really expect this router to offer much faster wireless speed according to this review: [URL]
View 12 Replies
View Related
Apr 30, 2013
I'm using a RV220W in my home office. Before this router I was. using a Sitecom router which did not cause any problems. I have setup a home network. The RV220W connects to the provider modem. The client components connect to the RV220W. Which acts as DHCP gateway. The DHCP features of the modem are disabled. I have assigned all network client devices to the same workgroup. I have to windows 7 PC's. one of them acts as fileserver. when trying to acces it from the other fixed PC or via a laptop the fileserver is visible but not accessable. I can not open it and access the shared folders.It has worked for a brief moment, but without changing any settings it stop working. I have never had accessability problems with the sitecom router. I have installed the latest firmware and tried rebooting the router several times. I have also started again with the factory defaults.
View 3 Replies
View Related
Jan 8, 2012
I have a cisco RV220W router used in a home environment. Recently I purchased a Siemens Gigaset A 580 IP phone. It works OK so far but I would like to optimize the configuration for VoIP traffic and apply QoS for VoIP on this router. Any guide with the recommended configuration and preferred settings of the same? I have not used QoS previously
View 1 Replies
View Related
