Cisco Routers :: RV042 Doesn't Get Ip From Bridged Modem Aztech 600e
Aug 5, 2012
i've just purchased cisco rv042. i want to connect to my ISP using modem (bridged). i tried to config pppoE on the router with my isp acount and connecting it to the modem. the issue is my router doesnt get any ip from the modem(aztech tnn 600e).
* the dhcp on the modem is working properly. i checked by connecting a computer to it, the ip was assigned. and another test i did, i connected the rv042 on "assign ip automatically and it got ip from the modem (worked well when the modem is bridged ot bridged).
View 15 Replies
ADVERTISEMENT
Mar 8, 2012
I'm having trouble getting my RV220W router to work with a DSL modem. I pre-configured the device and shipped it to one of our store locations. I came to find out that the site had an "Advanced" modem (according to the carrier) and I had to have them "bridge" the modem. Prior to having the modem "bridged" I was able to have the user plug the RV220W into the modem, and the computer that was hard-wired to the router was pulling the correct set of IP addresses, however, my VPN tunnel was not working because the WAN address that the RV220W was receiving was 192.168.2.12 instead of the staticly assigned IP address from the ISP After bridging the modem, the user is able to access the RV220W but he does not have internet connectivity. According to the carrier, this is because we need to enter their PPOE username and password into the RV220W. My only problem is that my on-site person is not very technical, and although I have access to one of our other sites with a working RV220W I'm not able to find where I enter this PPPOE information into the device. get this thing setup so that the customer is able to get connected to the internet, and that my RV220W is pulling the correct staticly assigned IP address from the ISP?
View 5 Replies
View Related
Oct 15, 2012
I am working overseas for a small company, trying to get an RV120 VPN router to connect to our network back home. Part of the problem is that I have to use a DSL modem here which is also a router, and so the WAN IP given to the modem is not the same one used by the VPN router.
Do we need to create a bridge between the two routers so that the VPN router can use the WAN IP from the ISP instead of a DHCP address on the local network? Or is this the wrong approach?
View 3 Replies
View Related
Mar 30, 2011
I need line settings for manual configuration.becouse seens i change my modem to aztech,i got a slow connection,not like before(good).
View 1 Replies
View Related
Sep 4, 2011
Basically, my internet's been fine until about a week ago. I'm currently using the Aztech DSL1000EW router/modem which has been working great up to now. My problem is this: after about 5-30 minutes (time fluctuates, annoying because after 15 minutes of continuous usage you think the problem's solved!) all webpages suddenly become 'unavailable'. I've disabled proxies under LAN settings, tried flushing DNS, resetting winsock with the netsh commands but to no avail. To get the internet to work again, I can just go to my router page, click disconnect and reconnect and it'll work for another 5-30 minutes.
View 8 Replies
View Related
Dec 5, 2012
Connecting the sip trunk provider modem and my network on the rv042 and connect my phone system on it so he can access both my sip trunk and internet connection.
I have 1 WAN modem from my sip trunk provider connected to the first WAN interface in the RV042.My network is connected to the second WAN interface programmed as a transparent bridge to link both lan segments together
however the link between the WAN2 interface and the network seems to go up and down and i cant ping my network gateway from a pc connected to the switchport of the RV042.
all i need is internet access to the phone system for email notification via a SMTP server.
View 1 Replies
View Related
Jan 23, 2012
I have a problem with my WAN ports. I can´t obtain a ip adress from my ISP. I´ve tried factory reset. Upgrade to lateset firmware. Clone MAC adress from my PC. Nothing is working.
But when I plug the WAN port into my Old router it receives an adress directly. When I plug the ISP connection directly into my pc or the old router it´s working as well.
I am using the latest firmware: RV0XX-v4.1.0.02-tm.bin
And My ISP has an interface with an ADSL modem SmartAX with DHCP.
View 2 Replies
View Related
Oct 23, 2012
Having some issues getting a site to site VPN connected between two RV042. Any experience getting this to work behind a Motorola SBG9000.Will I be able to get this working? Or will I have to organise a cable modem through my ISP instead
View 1 Replies
View Related
Aug 19, 2011
I have a Speedstream 4300 modem in bridge mode and a linksys WRT54G2 router set to PPPoE like I was instructed. On the status page of my router underneath the PPPoE setting it has IP, Subnet Mask, and Gateway all set to 0. The only advice I was able to obrain from my ISP was to powercycle the router and modem, which I did and no change.
View 1 Replies
View Related
Feb 19, 2012
We got a 1921 router that works fine. We ordered Verizon Businss One Static IP ADSL. It came with a Westell Modem that we configured in bridge mode. When we do a test by assigning a static IP to our laptop then hook it up to the Westell it works fine. We can browse the web. Then when we assign a static IP to the Ethernet on our 1921 then connect it to the Westell it doesn't work. We can't ping out from the router to for example 4.2.2.2. From the router we can't even ping the default gateway (on Verizon's side).
View 2 Replies
View Related
Nov 8, 2012
Using Cisco 1811W with IOS 15.1(4)M5. FE0 and FE1 are connected to the internet via Billion ADSL2+ modems operating in bridged mode. Both lines are similar so I'll only discuss FE0 from this point on.Local subnet is 192.168.128.0/24 with router on 192.168.128.1 as default gateway. Modem on FE0 has static LAN IP of 192.168.128.2 and when plugged into the switch on the LAN side, the web interface can be accessed at that IP address. Unplug the modem from the switch and plug it into FE0 and it now works as desired providing access from the router to the internet but the web interface is no longer accessable at 192.168.128.2
I tried adding a static route "ip route 192.168.128.2 255.255.255.255 FastEthernet 0" and also "ip route 192.168.128.2 255.255.255.255 Dialer 1" Neither worked and presumably it isn't that straight forward. Possibly NAT or other routing configuration required.Although there isn't much to configure when in bridged mode, I mostly want this setup so I can look at the ADSL connection status and for the modem to write messages to syslog (works when plugged into switch on LAN side), or SNMP access.
View 3 Replies
View Related
Feb 6, 2012
I'm trying to connect my Xbox 360 to Live by bridging my computer's wireless connection. I've done this before for a friend in a different city and it worked fine, and I felt very proud of myself for doing so. However when I try to connect here, the modem won't assign my Xbox an IP address. I've been into ipconfig/all and tried to manually assign the same IP address to the Xbox but to no avail. Same deal with the alternate MAC address option.
To speed things along here's the readout from my ipconfig/all:
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersSamsung>ipconfig/all
[Code].....
View 2 Replies
View Related
Feb 26, 2012
I'm trying to connect my WAG160N as a ADSL modem (disable the router function) and connect a real router (RVS4000)So, i put my WAG160N on birdged mode only, disable the DHCP on my RVS4000, i did configure my PPPOE access (user and password), change the IP adress 192.168.0.2.configure the DHCP and try to connect. i tryed to connect the RVS4000 and the WAG160N either with cross cable or a direct cable. I can get access to the RVS4000 192.168.0.2 and get access to the configuration menu but cannot get access to my WAG160N 192.168.0.1 even a simple ping.when i try to test the connection on my RVS4000 (status) it seems that my connection is up but i cannot get access to internet.
View 6 Replies
View Related
Jun 5, 2012
I've a Cisco SRP527W, it have a LAN in 192.168.1.0 range, now I need to put in bridge mode, to be transparent with my firewall, how can I do this?
View 3 Replies
View Related
Mar 7, 2013
I have a problem in my IPSec tunnel. One of the routers (Cisco 861) doesn't encrypt the packets but does decrypt the incoming ones from the remote peer (RV042). In the access-list for the wan interface I deny the traffic between the subnets and in the vpn access-list I permit the traffic.
View 4 Replies
View Related
Nov 21, 2012
Continued from [URL] which appears to have been closed by a moderator with a reference to Cisco small business website, but the registration there doesn't work, all buttons are inactive etc.
I just need to know what to do with this RV042. I have two modems, a cable and an ADSL. Both are configure correctly, in bridge mode. Both work fine when connected to WAN1, but when connected to WAN2 they never go online (dont' get IP address). The connect lights are on but they never go online.
Firmware Version: 1.3.13.02-tm
View 1 Replies
View Related
Feb 28, 2012
I was able to install the RV042 router to my ATT DSL line (WAN1 port-INTERNET) and it gets an external IP address automatically and the Internet works. When I connect my Comcast Internet to WAN2 port INTERNTE/DMZ) it doesn't get an IP address. and the Internet goes down and the WAN2 port ip address says 0.0.0.0.I've tried releasing/ renewing and it still says 0.0.0.0.Everything else is set as the default.
View 1 Replies
View Related
Oct 10, 2011
can't figure out what's killing my desktop's connection.I'm running Windows 6 Ultimate x64. I was using an Aztech Wireless-N WL522USB adaptor before, and it was working perfectly fine apart from the fact that it was a tad slow, which led me to buy a new Linksys AE1000 adaptor.I'm guessing I caused some kind of conflict, because after an hour or two of use (and after installation of the drivers), I started getting DRIVER_IRQL_NOT_LESS_OR_EQUAL BSODs, as well as my connection dying on me. I did not uninstall the drivers for the Aztech adaptor before installing the new one, and I have a feeling this might have something to do with it. Anyway, right now, I've switched back to the Aztech (intend to return the Linksys), and I'm still having connection problems. The tooltip of the wireless icon on the toolbar shows "No Network Access", while clicking on it shows "Limited Access". I have neither internet access nor local access to the router. The weird thing is that it works for a VERY short period of time after starting up, where I will have full internet access, and after which it will revert to the Limited Access state.
View 14 Replies
View Related
Oct 20, 2012
I'm using Aztech wl552usb and the gain/range is very bad.Recommend me some other USB Wireless Adapter?
View 2 Replies
View Related
Jan 24, 2013
I have RV042 and E4200 routers . I tried the manual UPnP port forwarding using Rv042 router and was succesful ( by typing 192.168.1.1 in the explorer and logged in using user name and password )
I am using a linux embedded system whose Internal IP ,Internal port are mapped .This system is connected to one of the LAN ports
I want to try auto UPnP port forwarding both for RV042 router and Linksys E4200 routers
After enabling the Upnp option only and logging out ,Can i add a port mapping entry in this router without logging in using a C++ program which runs on linux embedded system .
View 2 Replies
View Related
Aug 22, 2012
I was looking for a small business router that has VPN support and dual WAN support for load balancing. Upon reading reviews, I think RV042/RV042G is a good choice. Now am thinking if it supports intervlan/ router-on-a-stick configuration?
View 5 Replies
View Related
Dec 5, 2011
I am using router aztech-hw550-3g. i have Service pack 3 on my laptop. I was able to connect to my router fine but from the last 3 days i am unable to connect to my wireless network. Whenever i am trying to connect it is showing me a msg as unable to connect to you preferred network. It's Dhcp configured network.
View 1 Replies
View Related
Aug 16, 2011
I recently purchased an Aztech wireless-n repeater #WL556E to increase my signal strength on my patio. I followed the instructions step by step and it works for about an hour and then stops. This is on my Apple iPad first generation. If I restart my iPad it works for an hour or so and quits. I have the repeater about 7 feet up on a shelf.my wife has the identical iPad as mine and hers works fine on the repeater.
View 1 Replies
View Related
Sep 18, 2012
I just got E4200 and it seems my homeplug is not able to connect to router. I don't see it listed in DHCP Table under status. I could only see my Desktop was connected. Are these two not compatible? Homeplug works fine my old router which is Trendnet TEW-452BRP.
View 3 Replies
View Related
Aug 23, 2011
My Motorola SBG901 Modem/Router combo has stopped connecting to the internet. I have done all the troubleshooting with Comcast and with Motorola and it is out of warranty, so I will have to purchase a new one.In the mean time, I wanted to use it only as a wireless router connected to my Scientific Atlanta DPC2100R2 modem. Is there anyway to do this? Is there a way to disable the modem in the SBG901? Simply connecting with the ethernet cords has not worked. I connected the DPC2100 to the SBG901 via ethernet cord. My computer was able to pick up a wireless connection but there is no cable connection.
View 1 Replies
View Related
Jul 29, 2012
It has been 4 months since I upgraded my internet connection from 2 mbps to 4 mbps.I have called the ISP but they say the speed is okay.When I open 192.168.1.1 it says(datas shown below),but everytime i download something or measure my internet connection it never goes more than 2 mbps (max 230 kbs download[CODE]
View 3 Replies
View Related
Oct 29, 2012
I just got an used Pc from auction today.I installed it with Xp Pro. I am trying to connect it to my wire modem but it doesn't work.
View 4 Replies
View Related
Jun 20, 2011
My modem does not have a Ethernet plug in for my router. do I have to buy another modem for a 2nd computer?
View 1 Replies
View Related
Jan 15, 2012
I usually connect my PS3 to a switch which then goes to the BuT Home Hub and it works fine. However, I want to connect the PS3 directly to my Hub but when I plug it in to the Hub, it doesn't connect to the internet at all. Is there something I have to configure in order to get it to work?It is a PS3 160 GB Slim with Firmware 4.0.
View 2 Replies
View Related
Feb 26, 2011
I have a Netgear WRG614 and a Westell 610015 Modem. I need Port Forwarding. I have tried setting up a static IP then Port Forwarding but it doesn't work. I have tried port forwarding from the modem but it doesn't work. I wanna forward ports "80, 9958, and 5816". The reason is because I am gonna host a game server on my computer.
View 14 Replies
View Related
Apr 4, 2012
My Speedtouch 516v6 modem does'nt provide gateway adress to the TP-Link router. The modem can work in bridged mode or routed mode and I want to use routed mode. TP-Link has PPPoE mode but I would like to use a dynamicIP mode in which the router obtain network parameters from the modem and it does, but it does not obtain a gateway address.
View 2 Replies
View Related
Nov 7, 2012
I just received a new modem from my ISP acanac, the modem model is NetVito5300.When I connect the modem directly to my computer, I can access the internet, but if I connect through my wireless router, there's no wireless internet access. Wireless router model is CISCO Linksys E2000.I tried to download Cisco Connect Setup Software for PC and followed the step until one point it asked for my wireless username and password and I put them in correctly but it said my router was not successfully set up and failed. I should press the reset button and set the router to factory default mode, but I'm afraid I won't be able to set it up properly after doing so.What should I do to connect my new modem and wireless router properly so I have wireless internet access?
View 6 Replies
View Related
Oct 5, 2012
Ok this is the send router this has happened to but anyway after a power blink the router no longer recognizes that i have a modem connected to it no matter how many times I reboot both of them it can't recognize that i have a modem connected i know it is not the modem because i'm using it to type this right now directly connected to my desktop
I have windows 7
Linkysy E4200 V1
Century link DSL modem 660 series
View 9 Replies
View Related
