Cisco Routers :: RV120 Bridged With DSL Modem / Router?
Oct 15, 2012
I am working overseas for a small company, trying to get an RV120 VPN router to connect to our network back home. Part of the problem is that I have to use a DSL modem here which is also a router, and so the WAN IP given to the modem is not the same one used by the VPN router.
Do we need to create a bridge between the two routers so that the VPN router can use the WAN IP from the ISP instead of a DHCP address on the local network? Or is this the wrong approach?
View 3 Replies
ADVERTISEMENT
Mar 8, 2012
I'm having trouble getting my RV220W router to work with a DSL modem. I pre-configured the device and shipped it to one of our store locations. I came to find out that the site had an "Advanced" modem (according to the carrier) and I had to have them "bridge" the modem. Prior to having the modem "bridged" I was able to have the user plug the RV220W into the modem, and the computer that was hard-wired to the router was pulling the correct set of IP addresses, however, my VPN tunnel was not working because the WAN address that the RV220W was receiving was 192.168.2.12 instead of the staticly assigned IP address from the ISP After bridging the modem, the user is able to access the RV220W but he does not have internet connectivity. According to the carrier, this is because we need to enter their PPOE username and password into the RV220W. My only problem is that my on-site person is not very technical, and although I have access to one of our other sites with a working RV220W I'm not able to find where I enter this PPPOE information into the device. get this thing setup so that the customer is able to get connected to the internet, and that my RV220W is pulling the correct staticly assigned IP address from the ISP?
View 5 Replies
View Related
Aug 5, 2012
i've just purchased cisco rv042. i want to connect to my ISP using modem (bridged). i tried to config pppoE on the router with my isp acount and connecting it to the modem. the issue is my router doesnt get any ip from the modem(aztech tnn 600e).
* the dhcp on the modem is working properly. i checked by connecting a computer to it, the ip was assigned. and another test i did, i connected the rv042 on "assign ip automatically and it got ip from the modem (worked well when the modem is bridged ot bridged).
View 15 Replies
View Related
Aug 19, 2011
I have a Speedstream 4300 modem in bridge mode and a linksys WRT54G2 router set to PPPoE like I was instructed. On the status page of my router underneath the PPPoE setting it has IP, Subnet Mask, and Gateway all set to 0. The only advice I was able to obrain from my ISP was to powercycle the router and modem, which I did and no change.
View 1 Replies
View Related
Apr 10, 2012
Port forwarding on rv120 does not work. I have followed the workaround instructions: so i have created a firewall access rule on incoming port 21 to an internal ip address on the same port. The router has created the forwarding port rule. But port forwarding does not work. I have tried to use a custom service but nothing!
The router is reachable from wan, I can access via DNS the configuration page and I can ping the router on wan port.
View 10 Replies
View Related
Jul 11, 2011
I want to build a "hub and spoke" topology for one of my clients. For the "HUB" , I'm planning to use an SA540, with a static public IP provided by a 4Mb SDSL. For the "spokes" (21 at the moment), I'm planning to use RV120. They will be behind a NAT, provided by a "SAGEM LIVEBOX", and a static public IP. The boss will connect to the HUB using Cisco VPN client, or quickVPN, and get access to all the spokes. Some spokes will have to connect to each other, via the HUB. I searched a long time on this forum and reading documentation, but I didn't find at the moment the answer to my question : is this topology suitable with the choosen hardwares ?
View 7 Replies
View Related
Feb 19, 2012
We got a 1921 router that works fine. We ordered Verizon Businss One Static IP ADSL. It came with a Westell Modem that we configured in bridge mode. When we do a test by assigning a static IP to our laptop then hook it up to the Westell it works fine. We can browse the web. Then when we assign a static IP to the Ethernet on our 1921 then connect it to the Westell it doesn't work. We can't ping out from the router to for example 4.2.2.2. From the router we can't even ping the default gateway (on Verizon's side).
View 2 Replies
View Related
Jul 25, 2011
I'm having a problem forwarding port 1723. What i'm trying to do is to use VPN to access my server pc and I don't want to use the VPN software that is in the router. When I telnet the port it goes through but when i try to access it outside of the office I can't get through. I've been using [URL] to check port 1723 and I get this:
Error: I could not see your service on XX.XX.XX.XX on port (1723)
Reason: Connection refused
View 4 Replies
View Related
Nov 8, 2012
Using Cisco 1811W with IOS 15.1(4)M5. FE0 and FE1 are connected to the internet via Billion ADSL2+ modems operating in bridged mode. Both lines are similar so I'll only discuss FE0 from this point on.Local subnet is 192.168.128.0/24 with router on 192.168.128.1 as default gateway. Modem on FE0 has static LAN IP of 192.168.128.2 and when plugged into the switch on the LAN side, the web interface can be accessed at that IP address. Unplug the modem from the switch and plug it into FE0 and it now works as desired providing access from the router to the internet but the web interface is no longer accessable at 192.168.128.2
I tried adding a static route "ip route 192.168.128.2 255.255.255.255 FastEthernet 0" and also "ip route 192.168.128.2 255.255.255.255 Dialer 1" Neither worked and presumably it isn't that straight forward. Possibly NAT or other routing configuration required.Although there isn't much to configure when in bridged mode, I mostly want this setup so I can look at the ADSL connection status and for the modem to write messages to syslog (works when plugged into switch on LAN side), or SNMP access.
View 3 Replies
View Related
Feb 6, 2012
I'm trying to connect my Xbox 360 to Live by bridging my computer's wireless connection. I've done this before for a friend in a different city and it worked fine, and I felt very proud of myself for doing so. However when I try to connect here, the modem won't assign my Xbox an IP address. I've been into ipconfig/all and tried to manually assign the same IP address to the Xbox but to no avail. Same deal with the alternate MAC address option.
To speed things along here's the readout from my ipconfig/all:
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersSamsung>ipconfig/all
[Code].....
View 2 Replies
View Related
Feb 26, 2012
I'm trying to connect my WAG160N as a ADSL modem (disable the router function) and connect a real router (RVS4000)So, i put my WAG160N on birdged mode only, disable the DHCP on my RVS4000, i did configure my PPPOE access (user and password), change the IP adress 192.168.0.2.configure the DHCP and try to connect. i tryed to connect the RVS4000 and the WAG160N either with cross cable or a direct cable. I can get access to the RVS4000 192.168.0.2 and get access to the configuration menu but cannot get access to my WAG160N 192.168.0.1 even a simple ping.when i try to test the connection on my RVS4000 (status) it seems that my connection is up but i cannot get access to internet.
View 6 Replies
View Related
Jun 5, 2012
I've a Cisco SRP527W, it have a LAN in 192.168.1.0 range, now I need to put in bridge mode, to be transparent with my firewall, how can I do this?
View 3 Replies
View Related
Aug 23, 2011
My Motorola SBG901 Modem/Router combo has stopped connecting to the internet. I have done all the troubleshooting with Comcast and with Motorola and it is out of warranty, so I will have to purchase a new one.In the mean time, I wanted to use it only as a wireless router connected to my Scientific Atlanta DPC2100R2 modem. Is there anyway to do this? Is there a way to disable the modem in the SBG901? Simply connecting with the ethernet cords has not worked. I connected the DPC2100 to the SBG901 via ethernet cord. My computer was able to pick up a wireless connection but there is no cable connection.
View 1 Replies
View Related
May 23, 2011
I usually connect to another network with a VPN client, e.g. the Cisco VPN client. Is it possible to have the router to establish a tunnel to the destination thus omitting the need for a software client on the computer?
View 1 Replies
View Related
Jul 10, 2011
I would like to convert my cable modem Cisco epc3825 (bridge only), and thus can not function as a router. Before if I could, but my Internet Service provider has updated the firmware epc3825 and I can not pass it on to cable modem (bridge only).
View 2 Replies
View Related
Aug 9, 2011
I have a wireless N router (DIR-655) in bridge mode connected to a TWC combo modem/wireless G router. I have Tversity media server running on a computer connected to the TWC, but my PS3 which is connected wirelessly to the TWC combo can't see Tversity. What am I missing? Do I need to forward some port from somewhere? FYI, I'm set-up this way so my N router can deliver full N speed, and my G devices connect to the slower TWC router. Everything sees the internet with no problem. Also, to note that devices connected to the D-link can see Tversity, but devices connected to the TWC cannot see Tversity
View 4 Replies
View Related
Dec 10, 2011
I have 2 E4200's . One is connected to my ADSL Modem as DHCP and the other one is Bridged to the DHCP. I'm trying to connect to my E4200 that is set as Bridged. I am able to connect to my E4200 that is set as DHCP, but I cannot connect to the E4200 that is connected to that DHCP as Bridged.
How can I connect to that bridged E4200 because I want to upgrade the Firmware of the Bridged E4200?.
View 1 Replies
View Related
Jul 22, 2009
I cannot find any explicit instructions on this. Maybe they're calling it other things or implying it in other settings.
How do I configured a BEFSR41 to operate in bridged mode?
View 4 Replies
View Related
Nov 10, 2012
had a EA4200 about a year now, no probs, very stable, i'm thinking about getting a EA6500, for better coverage, iPhone apps, etc, would like to use my EA4200 in bridge mode from a EA6500, I'm a fairly new to networking etc, i'm assuming when the EA4200 is bridged, it will act like a repeater connected by cable, with same SSID ?
View 7 Replies
View Related
Feb 20, 2013
I put the ea4500 on Bridged mode, and now I cant connect!I know I have to put the new ip address, and when I do I choose direct conect, it ask me for a password, I put the password, I click to connect, and then it just sits there in waiting....
View 9 Replies
View Related
Sep 30, 2012
I'm trying to use my WAG120N router as a modem only/Bridged Mode and I've managed to enter all my settings needed on the WAG120N which is the Encapsulation to Bridged Mode Only, QoS to UBR, Type Of Connection to LLC, VPI and VCI to 0 and 35, DSL Modulation to Multi mode.On the EA4500's end I've entered my Usrname and password in the Internet settings and configured for PPPoE.
View 8 Replies
View Related
Dec 28, 2012
I have just recently replaced my Netgear router with an EA3500 and have it bridged t an Airport Express. From there I have an ethernet cable attached to an AV receiver (Pioneer 1021k), but all to often now with this new router to use any of the features of the receiver ie Airplay, iOS app remote, I must restart the router EVERY time. This is frustrating because the these issues were never present with the netgear router.
View 9 Replies
View Related
Dec 20, 2012
I am trying to setup a remote PC over a wireless access Point/Bridge to our FIOS router. Pic of setup is shown below. Everything is connected, there are no errors or security warnings shown in the ActionTec MI424 router. The RemotePC IP shows up as an Active Ethernet client in the Router config app. Moreover, I can run the connectivity test from the router app to the RemotePC and it passes that, and I can PING from the RemotePC to the Router. Yet I cannot reach the Internet from a Browser on the RemotePC (192.168.1.75). I am using (2) DLINK DAP-1522 Access Point/Bridge units and they have worked as expected. I set the Router log to list any blocked IP traffic as well, and it does not show anything being blocked from the RemotePC (192.168.1.75). So why can't I reach the Internet from the RemotePC? Seems like a gateway problem or I need to make some config changes in the Router.
View 2 Replies
View Related
Nov 2, 2012
EA4500 in bridged mode and I can log in the the CCC account but nothing appears on the screen. I was able to see the settings, etc with the previious firmware. I reset the router and tried different browsers, PC, etc. Now running Ver.2.1.39.144146.
View 9 Replies
View Related
Apr 5, 2013
I'm runing an ea3500 in bridged mode, classic configuration, firmware 1.0.30 build 126544. I got ftp working for my usb attached wv delements drive , but it is totally invisible in windows (except for ftp of course).I read in an older post that the usb drive in certain situations does not work (independent of disk manufacturer/type and such) and for certain configurations the ftp option might work but the windows mapped network drive doesn't , does that still apply? does it apply to bridged mode ?
View 1 Replies
View Related
Feb 1, 2013
I've set up PPPoE on my EA4500 router with a Vigor 120 modem in bridged mode and it says an internet connection is established, but the connection is extremely slow on all my devices. When I run the speed test within the EA4500 firmware it appears fine, but I cannot load any web pages on my laptop or other decives because the connection is so slow. The connection is slow with both wired and wireless connections. I've tried changing the MTU settings with no success. I've also tried using a different router and connecting the modem directly to my laptop and using PPPoE within the laptop and these both work fine, so I think it's clear there is a problem with the EA4500 router itself.
I'm just using the Vigor 120 to authenticate and connect to the internet itself, with the router in DHCP automatic configuration mode. I think this is causing a double NAT.
View 9 Replies
View Related
Sep 17, 2012
I recently purchased a new laptop computer and since I already had a wireless router I thought that I could get on line easy but, it seems the password I had written down does not work. I called my cable co. Charter to see if they could correct it. Well Charter changed it to something only God knows. Now neither Charter nor myself can make my laptop access the web without directly plugging into the router. What good is a wireless router that no one knows the password too? How I go about changing a password that I do not know and neither does my ISP.
View 2 Replies
View Related
Apr 26, 2012
How to connect 2 cisco modem in 1 3com router.
View 6 Replies
View Related
Jan 7, 2012
I would like to know if the Linksys X2000 ADSL2+ modem router will work with my IPTV service.
View 3 Replies
View Related
Oct 17, 2012
I'm trying to connect my Alvarion BreezeMax Si modem to my Wrt54gs Router, how do I do that.
View 1 Replies
View Related
Nov 23, 2012
Trouble connecting to the internet wireless with Motorola SB6120 and Linksys WRT120N. The modem works directly with LAN but as soon as I try to use the router, I can connect to the network but no internet is available.
View 4 Replies
View Related
Oct 29, 2012
I just got a DSL Modem router (DSL 2750U) which has DSL input for internetconnectivity.My internet service provider provides RJ45 Cable which needs LAN input socket on a router for internet connectivity. How do I connect?
View 4 Replies
View Related
Feb 7, 2011
I am trying to connect a Netgear wirless router to my cable modem. I have followed the instructions on the set up wizard but it fails to get a connection with the IP and DNS info I provide.I got the IP address info by connecting intially direct from the modem to the PC and then went to Run CMD and type ipconfig /all. I then started the set up wizard and followed the instructions, turning things on in specific order etc. After input the IP and DNS info it reports an error and tells me to check the address information is correct.My internet is a static IP connection (so it tells me and the IP information doesn't change).
View 3 Replies
View Related
