Connecting the sip trunk provider modem and my network on the rv042 and connect my phone system on it so he can access both my sip trunk and internet connection.
I have 1 WAN modem from my sip trunk provider connected to the first WAN interface in the RV042.My network is connected to the second WAN interface programmed as a transparent bridge to link both lan segments together
however the link between the WAN2 interface and the network seems to go up and down and i cant ping my network gateway from a pc connected to the switchport of the RV042.
all i need is internet access to the phone system for email notification via a SMTP server.
i've just purchased cisco rv042. i want to connect to my ISP using modem (bridged). i tried to config pppoE on the router with my isp acount and connecting it to the modem. the issue is my router doesnt get any ip from the modem(aztech tnn 600e).
* the dhcp on the modem is working properly. i checked by connecting a computer to it, the ip was assigned. and another test i did, i connected the rv042 on "assign ip automatically and it got ip from the modem (worked well when the modem is bridged ot bridged).
We are experimenting with virtual machines running on some laptops here as part of a future deployment.Equipment in use:
-5508 WLC -1262 LWAP
The actual operating system has no issues connecting to the wireless. When you start the virtual machine on any client machine (OSX, Win 7, Win XP, anything) it is unable to get an IP through an external DHCP server when the VM is set up to use a bridged connection.This works fine with Autonomous access points and over cable all mapped to the same VLAN. Helper addresses are configured on the VLAN.Is this a limitation of the WLC where it cannot provide more than one IP address per MAC? Is it a limitation of CAPWAP? Or is there an option to turn of DHCP snooping (which I suspect to be the cause of the issue)?
Recently my xbox live connection, which is bridged through my desktop, has been disconnecting about every 10 minutes of online gameplay. Now i want to give as much information possible for the sake of everyone else. Previously when i was running the bridged connection, everything was fine. My old set up was as follows: The computer in my home office is a dell Inspiron 620. The high speed modem it's connected to is a motorola 2210- 02. Then I ran a Netgear Wireless G router (WGR614V10) which all the wireless electronics connect to. The computer in my room is a HP Compaq Presario PC (SR5807C) which connected to the wireless router using a Netgear WPN111V3 wireless USB adapter. From there I ran an ethernet cable from my Xbox 360 into the ethernet port in the back of my PC and bridged the connections. This setup was brutally effective for about 2 years. One day my wireless adapter, connected to the HP Compaq burnt out. This is when the problems began. I replaced it with a Netgear N300 Wireless USB adapter, and the HP Compaq Presario connects to the wireless router just fine and never loses connection. But when I bridged the connections between the computer and the Xbox 360, my xbox live began to go out.... ALL THE TIME.... All the of the above information remains the same except for the new wireless USB adapter (N300). I've tried everthing from restarting the computer, resetting all settings to default (both the 360 and the wireless settings on my computer), port forwarding and triggering by microsoft xbox live recommendations and anything in between. I would have figured with the newer USB adapter my live should be working better but every 10 minutes it disconnects me from xbox live. (When I get disconnected from live, the computer, from what I can tell, remains connected while the bridge encounters all the issues) At the same time apps like netflix and youtube work fine all day and I never get disconnected, only when I'm gaming (COD MW3, Halo Reach, etc.).
I've set up PPPoE on my EA4500 router with a Vigor 120 modem in bridged mode and it says an internet connection is established, but the connection is extremely slow on all my devices. When I run the speed test within the EA4500 firmware it appears fine, but I cannot load any web pages on my laptop or other decives because the connection is so slow. The connection is slow with both wired and wireless connections. I've tried changing the MTU settings with no success. I've also tried using a different router and connecting the modem directly to my laptop and using PPPoE within the laptop and these both work fine, so I think it's clear there is a problem with the EA4500 router itself.
I'm just using the Vigor 120 to authenticate and connect to the internet itself, with the router in DHCP automatic configuration mode. I think this is causing a double NAT.
I have successfully connected two RV042s to establish a VPN gateway to VPN gateway connection. I have the follow questions:
1. I would like to keep the VPN tunnel connection time indefinite. Is it sufficient by checking the "Keep-Alive" box on the VPN -> Gateway To Gateway -> Advance page? Or, I have to ping the RV042 periodically?
2. Do the "Phase 1/Phase 2 SA Life Time" (on VPN -> Gateway To Gateway page) settings have any impact on keeping the VPN connection time indefinite? What are the optimal values for them?
3. Is there an API, command, or script to replace a manual clicking on the "CONNECT" button to establish the VPN tunnel from the VPN -> Summary page? Or, is there a way to accomplish this at power up?
4. Is there a way to establish a VPN tunnel without going through login and clicking the "CONNECT" button? (Auto connect at power up?)
I have 2 WAN connection @ my office. One is the static IP from Reliance Network
The other connection of WAN is dynamic from AIR TEL...
When i logged into my router. I can see the dynamic IP from Reliance on WAN1 status. But on WAN2 is see everything as 0.0.0.0. The WAN2 configuration has been set to get the IP automatically...
I tried the other solution offered by one of the support guys, by turning on and off the modem, but that does not work...
Or do i need to change the WAN2 connection to be PPoE or something...
I have a RV042 VPN Router inside an ASA 5505 running version 7.2. I am attempting to connect from the outside to the RV042. I have read for 2 days now and tried everything I have found and had no success. I can connect from inside the network to the RV042 so I know that is setup correctly. I have found links on several posts to the official Cisco support documents but they make no sense to me. This is my first experience with a Cisco Firewall.
We also have a security camera network that we access externally and I have successfully set up the port forwarding for this. Here is my current running configuration. The inside ip address of the RV042 is 192.168.168.25. I had port 1723 forwarded, opened GRE, and have setup PPTP inspection. I have deleted the port forwarding at this point.
Result of the command: "show running-config" : Saved ASA Version 7.2(3) hostname suite domain-name hivermont.com enable password vwiH3D2KQdqR57As encrypted names interface Vlan1 name if inside security-level 100 ip address 192.168.168.1 255.255.255.0 ospf cost 10 [code].....
How can I configure VPN connection between Cisco RV042 and Fritz!box 7170?I can establish VPN channel with Linksys RV042 with firmware 1.3.12.6-tm. When I set the same setting to Cisco RV042 (firmware v4.0.2.08-tm) VPN channel is not established.
Office-RV042 with static IP ->SBS2003 (10.10.10.5/ 255.255.255.0) Remote: BEFSR41 with Dynamic -> XP sp3 VPN client (192.168.3.x/ 255.255.255.248)
Within the RV042 I have enabled the PPtP server and assigned a user. No port forwarding enabled. All VPN passthroughs and firewall is enabled. DHCP server is disabled.I can establish a connection to the rv042 and ping PCs including the sbs domain server on the office side but am unable to browse any folders. When I attempt to access a network folder located on the office server I am prompted for a username/ password. Upon entering my domain credentials I get an error stating: "the user name you typed is the same user name you logged in with. That user name has already been tried. A domain controller cannot be found to verify that user name"
I have an RV082 and a RV042. I have been able to successfully establish a gateway to gateway vpn connection between them both, but both Routers unable to ping each other and I can't remotely administer each router through the VPN connection.
So here is my issue. I have two sites, each with a Linksys RV042 on thier site.
Site 1: External: 142.142.142.142 Internal: 192.168.25.0/24
Site 2: External: 143.143.143.143 Internal: 192.168.26.0/24
We have setup a site-to-site VPN between these sites, and all traffic is running back and forth without isse.
At Site 1 we have configured the Client VPN for use with the QuickVPN software. Again, for site 1, this is not an issue. We are able to access all internal resources at Site 1 without issue (expect for some DNS related problems).
The problem that we have is attempting to access Site 2 resources via the QuickVPN connection at Site 1. Even though they are not suppose to exist, we are able to ping 192.168.26.1-6 (which are ghost addresses likely created by the RV042's) but no actual systems on at Site 2.
I have added the Client VPN connection at Site 2, but it has the same problem accessing resources at Site 1.
Im able to create a gateway tunnel with two rv042 routers in different locations ( i can see the tunnel connected in the router) but the quick vpn utility is not working , i also tried to use the pptp as server as an alternative( im able to connect using windows connection to the pptp server but whenever I browse any of the four ip's allowed for the pptp server \10.0.0.200-204 it takes me to the documents of the local computer....I attached the configuration for one of the routers it is the same as the other end , just the information is flipped.
I'm a Cisco newbie and I'm in the following situation:
1>The router (867) must connect to my ISP in 1483 bridged (2684 bridged) mode, LLC, VPI/VCI 0/35 2>WAN IP will be assigned by ISP (DHCP) 3>No username and password required to establish the connection 4>MAC-Cloning is advised, not required 5>Firewall behind 867, WAN IP should be assigned to WAN interface firewall, connection established by 867 6>867 router will be used as a switch, so no NAT required. NAT will be setup on the firewall 7>Connection type: Analog (annex A)
The required setup can be fixed by configuring the 867 in half-bridged mode, but I don't no how and I don't know exactly how to config the 867 in bridged mode.
First, it's even hard to setup a good bridged config.
version 15.1no service padservice tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryptionservice sequence-numbers!hostname router1!boot-start-markerboot-end-marker!logging buffered 51200logging console criticalenable secret 5 ****!no aaa new-modelmemory-size iomem 10clock timezone GMT 1clock summer-time GMT date Mar 30 2010 1:00 Oct 26 2035 1:59!!no ip source-route!ip cefno ip bootp serverno ip domain lookupip domain name domain.local!!!!username admin privilege 15 secret 5 ***!!ip tcp synwait-time 10ip ssh time-out 60ip ssh authentication-retries 2!!!!!!!interface ATM0 no ip address no atm ilmi-keepalive!interface ATM0.1 point-to-point pvc
Is it possible to build two separate bridged connections from one "base"?
I'd need to connect to two other buildings which luckily happen to be quite on the same direction (antennawise). how to configure this into the devices I call "base", "building1" and "building2". The first building is about 50 meters and the other about 120 meters away. 11Mbps would be adequate for both. A some kind of encryption would be needed.
I would like to convert my cable modem Cisco epc3825 (bridge only), and thus can not function as a router. Before if I could, but my Internet Service provider has updated the firmware epc3825 and I can not pass it on to cable modem (bridge only).
I am have a lot of difficulty getting my WET610N to connect to my WRVS4400N. I have tried almost everything. I have some older PC's, as well as my PS3, that we use to use on the network and they only connect B/G. I have tried auto DHCP and static IP on the bridge. It seems that the only way that the bridge works is by using the WPS function that the business class routers do not have.
I recently got the sbg6580 an want it to work in bridged mode with my linksys wrt54g router. The problem is everything that is connected wirelessly like my Xbox or iPhone are connected to the Internet but my desktop pc which is a wired connection won't connect to the Internet.When I directly connect the modem to my desktop it works fine.
I have a question concerning replacing a 352 bridged network with 1552 mesh access points. Theoretically, imagine a centralized 352 with an omnidirectional antenna that is linked to multiple 352's with yagi antennas in a hub-spoke fashion. If this central 352 is replaced with a 1552 access point, will the existing Yagi's be able to talk to the 1552? I understand that the Yagi's AP's should be replaced with 1552's as well (thus forming a mesh network as the 1552s are designed to do) but for the sake of theory please assume the 'spoke' 352s will not be replaced. I have the understanding that the 1552s communicate over the 802.11a for the backhaul so I'm thinking this would cause some issues with the 352's.
I'm having trouble getting my RV220W router to work with a DSL modem. I pre-configured the device and shipped it to one of our store locations. I came to find out that the site had an "Advanced" modem (according to the carrier) and I had to have them "bridge" the modem. Prior to having the modem "bridged" I was able to have the user plug the RV220W into the modem, and the computer that was hard-wired to the router was pulling the correct set of IP addresses, however, my VPN tunnel was not working because the WAN address that the RV220W was receiving was 192.168.2.12 instead of the staticly assigned IP address from the ISP After bridging the modem, the user is able to access the RV220W but he does not have internet connectivity. According to the carrier, this is because we need to enter their PPOE username and password into the RV220W. My only problem is that my on-site person is not very technical, and although I have access to one of our other sites with a working RV220W I'm not able to find where I enter this PPPOE information into the device. get this thing setup so that the customer is able to get connected to the internet, and that my RV220W is pulling the correct staticly assigned IP address from the ISP?
Whatever a NAT is supported for ACE-20 module? I do need to convert working CSM(SLB) config to ACE configuration and I am not quite sure if the configuration below is correct. ACE module should be configured in bridge mode with two vlans - vlan 36 (client) and vlan 436 (server) - bridged with interface bvi 36. NAT on ACE configurad as "nat dynamic 1025 vlan 436" into corresponding "policy-map type loadbalance". Check two parts of configs and if the ACE config is properly converted from CSM and will be working in the same way (especialy for NAT). [code]
I am working overseas for a small company, trying to get an RV120 VPN router to connect to our network back home. Part of the problem is that I have to use a DSL modem here which is also a router, and so the WAN IP given to the modem is not the same one used by the VPN router.
Do we need to create a bridge between the two routers so that the VPN router can use the WAN IP from the ISP instead of a DHCP address on the local network? Or is this the wrong approach?
I have been trying this for ours and need to get it to work for a small branch office so I can get their cisco device connected and phones working.
The device works fine if I assigned it an IP address but the minute I set bridge mode only and assign the static IP to my system then nothing works. I have the latest firmware.
I'm trying to connect my WAG160N as a ADSL modem (disable the router function) and connect a real router (RVS4000)So, i put my WAG160N on birdged mode only, disable the DHCP on my RVS4000, i did configure my PPPOE access (user and password), change the IP adress 192.168.0.2.configure the DHCP and try to connect. i tryed to connect the RVS4000 and the WAG160N either with cross cable or a direct cable. I can get access to the RVS4000 192.168.0.2 and get access to the configuration menu but cannot get access to my WAG160N 192.168.0.1 even a simple ping.when i try to test the connection on my RVS4000 (status) it seems that my connection is up but i cannot get access to internet.
I am desiging a topology with two Cat 6509 and Two ACE Module, one ACE per Catalyst. I am thinking to use bridge mode for the customer contexts, I would like to know if the Bridged mode is an Assymetric topology.
The server gateway is the ip address of the ACE or the Router?
I have a Speedstream 4300 modem in bridge mode and a linksys WRT54G2 router set to PPPoE like I was instructed. On the status page of my router underneath the PPPoE setting it has IP, Subnet Mask, and Gateway all set to 0. The only advice I was able to obrain from my ISP was to powercycle the router and modem, which I did and no change.
I have a wireless N router (DIR-655) in bridge mode connected to a TWC combo modem/wireless G router. I have Tversity media server running on a computer connected to the TWC, but my PS3 which is connected wirelessly to the TWC combo can't see Tversity. What am I missing? Do I need to forward some port from somewhere? FYI, I'm set-up this way so my N router can deliver full N speed, and my G devices connect to the slower TWC router. Everything sees the internet with no problem. Also, to note that devices connected to the D-link can see Tversity, but devices connected to the TWC cannot see Tversity
I have 2 E4200's . One is connected to my ADSL Modem as DHCP and the other one is Bridged to the DHCP. I'm trying to connect to my E4200 that is set as Bridged. I am able to connect to my E4200 that is set as DHCP, but I cannot connect to the E4200 that is connected to that DHCP as Bridged.
How can I connect to that bridged E4200 because I want to upgrade the Firmware of the Bridged E4200?.
had a EA4200 about a year now, no probs, very stable, i'm thinking about getting a EA6500, for better coverage, iPhone apps, etc, would like to use my EA4200 in bridge mode from a EA6500, I'm a fairly new to networking etc, i'm assuming when the EA4200 is bridged, it will act like a repeater connected by cable, with same SSID ?
