Is it possible to build two separate bridged connections from one "base"?
I'd need to connect to two other buildings which luckily happen to be quite on the same direction (antennawise). how to configure this into the devices I call "base", "building1" and "building2". The first building is about 50 meters and the other about 120 meters away. 11Mbps would be adequate for both. A some kind of encryption would be needed.
i have AIR-BR1310G that came with its proper power injector AIR-PWRINJ-BLR2 can this power injector be feed using a POE switch or do i have to use the 48v power adapter
View 1 Replies View RelatedI purchased a used AIR BR1310G-A--K9-R from a local high school that was rebuilding their athletic field. The AP was used for communications for their pressbox staff. The AIR BR1310G was part of the schools campus wide WiFi network and was upgraded to an lwapp image c1310-k9w8-m 12.4 3c JA. Our home sits on a large lot and I would like to convert the BR1310G back to an autonomous AP.
In order convert it back to an automonous AP, I will need the original image. The school used a contractor for their WiFi network and they do not have a backup of the original image. I do not have a service account with Cisco so downloading the autonomous image from the Cisco website is out. What are my options for either obtaining an image file or using the current managed image without a WLC?
Does WLC 2504 works with AIR-AP1231G-E-K9 and with AIR-BR1310G-E-K9 after I upgraded form AP to LAP the AP ?
View 4 Replies View Relatedhowever recently when i check my internet usage log on my wireless company (Rogers) the usage is totally off from what my bandwidth tracker shows me. So i decide to turn off my wifi and see what happens, there has always been this weird wifi connection appearing whenever my wifi appears, then afterwards when i turn off my wifi the suspicious wifi connections disappear. is this possible that someone is using our wifi? i might just be overreacting but it has brought me to concern that if the usage continues my family will have to end up paying over $30 for extra internet use. it is very frustrating me because when i check my DHCP client table it only shows 3 connection, ethernet - my desktop which is not turned on, 2 wireless connection - my laptop and my sister's laptop.
View 6 Replies View RelatedI am have a lot of difficulty getting my WET610N to connect to my WRVS4400N. I have tried almost everything. I have some older PC's, as well as my PS3, that we use to use on the network and they only connect B/G. I have tried auto DHCP and static IP on the bridge. It seems that the only way that the bridge works is by using the WPS function that the business class routers do not have.
View 1 Replies View RelatedI have a question concerning replacing a 352 bridged network with 1552 mesh access points. Theoretically, imagine a centralized 352 with an omnidirectional antenna that is linked to multiple 352's with yagi antennas in a hub-spoke fashion. If this central 352 is replaced with a 1552 access point, will the existing Yagi's be able to talk to the 1552? I understand that the Yagi's AP's should be replaced with 1552's as well (thus forming a mesh network as the 1552s are designed to do) but for the sake of theory please assume the 'spoke' 352s will not be replaced. I have the understanding that the 1552s communicate over the 802.11a for the backhaul so I'm thinking this would cause some issues with the 352's.
View 2 Replies View RelatedI have a wireless N router (DIR-655) in bridge mode connected to a TWC combo modem/wireless G router. I have Tversity media server running on a computer connected to the TWC, but my PS3 which is connected wirelessly to the TWC combo can't see Tversity. What am I missing? Do I need to forward some port from somewhere? FYI, I'm set-up this way so my N router can deliver full N speed, and my G devices connect to the slower TWC router. Everything sees the internet with no problem. Also, to note that devices connected to the D-link can see Tversity, but devices connected to the TWC cannot see Tversity
View 4 Replies View RelatedI have 2 E4200's . One is connected to my ADSL Modem as DHCP and the other one is Bridged to the DHCP. I'm trying to connect to my E4200 that is set as Bridged. I am able to connect to my E4200 that is set as DHCP, but I cannot connect to the E4200 that is connected to that DHCP as Bridged.
How can I connect to that bridged E4200 because I want to upgrade the Firmware of the Bridged E4200?.
had a EA4200 about a year now, no probs, very stable, i'm thinking about getting a EA6500, for better coverage, iPhone apps, etc, would like to use my EA4200 in bridge mode from a EA6500, I'm a fairly new to networking etc, i'm assuming when the EA4200 is bridged, it will act like a repeater connected by cable, with same SSID ?
View 7 Replies View RelatedI put the ea4500 on Bridged mode, and now I cant connect!I know I have to put the new ip address, and when I do I choose direct conect, it ask me for a password, I put the password, I click to connect, and then it just sits there in waiting....
View 9 Replies View RelatedI have a WLC 5508 with LWAP 1242 with wireless bridges connected to the APs I cannot get DHCP to pass through the bridge to the PC connected to the bridge.
View 5 Replies View RelatedI'm trying to use my WAG120N router as a modem only/Bridged Mode and I've managed to enter all my settings needed on the WAG120N which is the Encapsulation to Bridged Mode Only, QoS to UBR, Type Of Connection to LLC, VPI and VCI to 0 and 35, DSL Modulation to Multi mode.On the EA4500's end I've entered my Usrname and password in the Internet settings and configured for PPPoE.
View 8 Replies View RelatedI have a WAG200G as my ADSL modem and wireless access point. I would like to build two small wired networks that are remote from the location of the wireless access point (i.e. where my telephone line comes in) so that I can connect several network cabled devices in each location (e.g. NAS drive, TV, games consoles etc). I cannot run network cables to these locaations but believe that I can bridge them via the wireless. At a pinch, I could have only one cabled sub-network but would prefer two.
View 4 Replies View RelatedI have just recently replaced my Netgear router with an EA3500 and have it bridged t an Airport Express. From there I have an ethernet cable attached to an AV receiver (Pioneer 1021k), but all to often now with this new router to use any of the features of the receiver ie Airplay, iOS app remote, I must restart the router EVERY time. This is frustrating because the these issues were never present with the netgear router.
View 9 Replies View RelatedI have an e4200v1 in bridge mode (LAN IP 192.168.1.2) connected via its WAN port to a LAN port on the primary router at 192.168.1.1.
Guest Wireless works perfectly in Ver. 1.0.04 build 11 but not in Ver. 1.0..05 Build 7.
I want to set up an E1200 as a wireless access point for guests, and ordinarily I'd be happy to connect it LAN-to-WAN and have it create its own subnet, but I need to connect one office PC to it also because connecting the E1200 to the main gateway displaces that office PC from the last Ethernet port on the main router.
So I disabled DHCP on the E1200 and connected it LAN-to-LAN. The modem is at a fixed, non-configurable address of 192.168.0.1/255.255.0.0 and the main router is at 10.0.0.1/255.255.255.0. I set the E1200 to a static IP of 10.0.0.12/255.255.255.0.The E1200's primary wireless connection works fine. The guest access connects, but it does not prompt for a password and web pages generate a "failed to load" sort of message.I temporarily connected the E1200 as the main router and re-enabled DHCP, though I kept the static IP of 10.0.0.12/255.255.255.0, and in this configuration the guest access worked. I observed that it connected via 192.168.33.1/guestaccess.cgi (or something very similar to that).
I'm trying to connect my Xbox 360 to Live by bridging my computer's wireless connection. I've done this before for a friend in a different city and it worked fine, and I felt very proud of myself for doing so. However when I try to connect here, the modem won't assign my Xbox an IP address. I've been into ipconfig/all and tried to manually assign the same IP address to the Xbox but to no avail. Same deal with the alternate MAC address option.
To speed things along here's the readout from my ipconfig/all:
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersSamsung>ipconfig/all
[Code].....
EA4500 in bridged mode and I can log in the the CCC account but nothing appears on the screen. I was able to see the settings, etc with the previious firmware. I reset the router and tried different browsers, PC, etc. Now running Ver.2.1.39.144146.
View 9 Replies View RelatedI'm runing an ea3500 in bridged mode, classic configuration, firmware 1.0.30 build 126544. I got ftp working for my usb attached wv delements drive , but it is totally invisible in windows (except for ftp of course).I read in an older post that the usb drive in certain situations does not work (independent of disk manufacturer/type and such) and for certain configurations the ftp option might work but the windows mapped network drive doesn't , does that still apply? does it apply to bridged mode ?
View 1 Replies View RelatedI've set up PPPoE on my EA4500 router with a Vigor 120 modem in bridged mode and it says an internet connection is established, but the connection is extremely slow on all my devices. When I run the speed test within the EA4500 firmware it appears fine, but I cannot load any web pages on my laptop or other decives because the connection is so slow. The connection is slow with both wired and wireless connections. I've tried changing the MTU settings with no success. I've also tried using a different router and connecting the modem directly to my laptop and using PPPoE within the laptop and these both work fine, so I think it's clear there is a problem with the EA4500 router itself.
I'm just using the Vigor 120 to authenticate and connect to the internet itself, with the router in DHCP automatic configuration mode. I think this is causing a double NAT.
I'm a Cisco newbie and I'm in the following situation:
1>The router (867) must connect to my ISP in 1483 bridged (2684 bridged) mode, LLC, VPI/VCI 0/35
2>WAN IP will be assigned by ISP (DHCP)
3>No username and password required to establish the connection
4>MAC-Cloning is advised, not required
5>Firewall behind 867, WAN IP should be assigned to WAN interface firewall, connection established by 867
6>867 router will be used as a switch, so no NAT required. NAT will be setup on the firewall
7>Connection type: Analog (annex A)
The required setup can be fixed by configuring the 867 in half-bridged mode, but I don't no how and I don't know exactly how to config the 867 in bridged mode.
First, it's even hard to setup a good bridged config.
version 15.1no service padservice tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryptionservice sequence-numbers!hostname router1!boot-start-markerboot-end-marker!logging buffered 51200logging console criticalenable secret 5 ****!no aaa new-modelmemory-size iomem 10clock timezone GMT 1clock summer-time GMT date Mar 30 2010 1:00 Oct 26 2035 1:59!!no ip source-route!ip cefno ip bootp serverno ip domain lookupip domain name domain.local!!!!username admin privilege 15 secret 5 ***!!ip tcp synwait-time 10ip ssh time-out 60ip ssh authentication-retries 2!!!!!!!interface ATM0 no ip address no atm ilmi-keepalive!interface ATM0.1 point-to-point pvc
[code].....
Connecting the sip trunk provider modem and my network on the rv042 and connect my phone system on it so he can access both my sip trunk and internet connection.
I have 1 WAN modem from my sip trunk provider connected to the first WAN interface in the RV042.My network is connected to the second WAN interface programmed as a transparent bridge to link both lan segments together
however the link between the WAN2 interface and the network seems to go up and down and i cant ping my network gateway from a pc connected to the switchport of the RV042.
all i need is internet access to the phone system for email notification via a SMTP server.
I would like to convert my cable modem Cisco epc3825 (bridge only), and thus can not function as a router. Before if I could, but my Internet Service provider has updated the firmware epc3825 and I can not pass it on to cable modem (bridge only).
View 2 Replies View RelatedI recently got the sbg6580 an want it to work in bridged mode with my linksys wrt54g router. The problem is everything that is connected wirelessly like my Xbox or iPhone are connected to the Internet but my desktop pc which is a wired connection won't connect to the Internet.When I directly connect the modem to my desktop it works fine.
View 1 Replies View RelatedI'm having trouble getting my RV220W router to work with a DSL modem. I pre-configured the device and shipped it to one of our store locations. I came to find out that the site had an "Advanced" modem (according to the carrier) and I had to have them "bridge" the modem. Prior to having the modem "bridged" I was able to have the user plug the RV220W into the modem, and the computer that was hard-wired to the router was pulling the correct set of IP addresses, however, my VPN tunnel was not working because the WAN address that the RV220W was receiving was 192.168.2.12 instead of the staticly assigned IP address from the ISP After bridging the modem, the user is able to access the RV220W but he does not have internet connectivity. According to the carrier, this is because we need to enter their PPOE username and password into the RV220W. My only problem is that my on-site person is not very technical, and although I have access to one of our other sites with a working RV220W I'm not able to find where I enter this PPPOE information into the device. get this thing setup so that the customer is able to get connected to the internet, and that my RV220W is pulling the correct staticly assigned IP address from the ISP?
View 5 Replies View RelatedWhatever a NAT is supported for ACE-20 module? I do need to convert working CSM(SLB) config to ACE configuration and I am not quite sure if the configuration below is correct. ACE module should be configured in bridge mode with two vlans - vlan 36 (client) and vlan 436 (server) - bridged with interface bvi 36. NAT on ACE configurad as "nat dynamic 1025 vlan 436" into corresponding "policy-map type loadbalance". Check two parts of configs and if the ACE config is properly converted from CSM and will be working in the same way (especialy for NAT). [code]
View 2 Replies View RelatedI am working overseas for a small company, trying to get an RV120 VPN router to connect to our network back home. Part of the problem is that I have to use a DSL modem here which is also a router, and so the WAN IP given to the modem is not the same one used by the VPN router.
Do we need to create a bridge between the two routers so that the VPN router can use the WAN IP from the ISP instead of a DHCP address on the local network? Or is this the wrong approach?
Just wondering of this model of WAP - AIR-CAP3502I-X-K9—802.11a/g/ is working standalone with out a controller , or is it only controller based ?
View 11 Replies View RelatedI have been trying this for ours and need to get it to work for a small branch office so I can get their cisco device connected and phones working.
The device works fine if I assigned it an IP address but the minute I set bridge mode only and assign the static IP to my system then nothing works. I have the latest firmware.
I'm trying to connect my WAG160N as a ADSL modem (disable the router function) and connect a real router (RVS4000)So, i put my WAG160N on birdged mode only, disable the DHCP on my RVS4000, i did configure my PPPOE access (user and password), change the IP adress 192.168.0.2.configure the DHCP and try to connect. i tryed to connect the RVS4000 and the WAG160N either with cross cable or a direct cable. I can get access to the RVS4000 192.168.0.2 and get access to the configuration menu but cannot get access to my WAG160N 192.168.0.1 even a simple ping.when i try to test the connection on my RVS4000 (status) it seems that my connection is up but i cannot get access to internet.
View 6 Replies View RelatedWe are experimenting with virtual machines running on some laptops here as part of a future deployment.Equipment in use:
-5508 WLC
-1262 LWAP
The actual operating system has no issues connecting to the wireless. When you start the virtual machine on any client machine (OSX, Win 7, Win XP, anything) it is unable to get an IP through an external DHCP server when the VM is set up to use a bridged connection.This works fine with Autonomous access points and over cable all mapped to the same VLAN. Helper addresses are configured on the VLAN.Is this a limitation of the WLC where it cannot provide more than one IP address per MAC? Is it a limitation of CAPWAP? Or is there an option to turn of DHCP snooping (which I suspect to be the cause of the issue)?
I've a Cisco SRP527W, it have a LAN in 192.168.1.0 range, now I need to put in bridge mode, to be transparent with my firewall, how can I do this?
View 3 Replies View Related