Linksys Cable / DSL :: X2000 Bridged Mode Only?

Dec 23, 2011

I have been trying this for ours and need to get it to work for a small branch office so I can get their cisco device connected and phones working.
 
The device works fine if I assigned it an IP address but the minute I set bridge mode only and assign the static IP to my system then nothing works. I have the latest firmware.

View 1 Replies


ADVERTISEMENT

Linksys Cable / DSL :: WAG54G2 Switch To Bridged Mode Only?

Oct 20, 2010

My Encapsulation router WAG54G2  switch RFC 2516 PPPoE to Bridged mode only everyday and all configuration that i made will reset and also Application & Gaming button error when i click.I'v reset to factory default and upgrade the firmwire to the latest one but it not work also  I replace the device but nothing changed.The problem will solve if I cut the powir off and restarted agein. 

View 3 Replies View Related

Linksys Cable / DSL :: X2000 Dual WAN Mode

Oct 8, 2012

Can the 2 WAN ports be  connected at the same time to provide failover and if so can this be configured for priority/ delay etc.A user has a very poor ADSL service so also has a bidirectional satellite link. Due to the latter's high latency I don't want it dropping that connection too quickly.

View 1 Replies View Related

Linksys Cable / DSL :: RVS 4000 Connected To WAG160N Bridged Mode Only

Feb 26, 2012

I'm trying to connect my WAG160N as a ADSL modem (disable the router function) and connect a real router (RVS4000) So, i put my WAG160N on birdged mode only, disable the DHCP on my RVS4000, i did configure my PPPOE access (user and password), change the IP adress 192.168.0.2 configure the DHCP ... and connect ... no way !
 
i tryed to connect either with cross cable or a direct cable ... same result. I can get access to the RVS4000 192.168.0.2 bit cannot get acess to my WAG160N 192.168.0.1 (strange ... don't have explanation for that) even a simple ping !
 
when i try to test the connection on my RVS4000 ... it seems that my connection is up .

View 7 Replies View Related

Linksys Cable / DSL :: WAG54G2 Switches To Bridged Mode Every Few Hours?

Jun 28, 2012

I have a WAG54G2 working fine for more than 2 years now. It has the initial firmware version 1.00.10
 
Recently I mode it from my home to my store, where I have a already working CCTV setup. Initially the router did not work, but once the service provider removed the mac-id binding (with my previous ADSL2+ router) the WAG54G2 was connecting on DSL. However it never got a DNS value. Currently I am using it with a fixed DNS.
 
After a few days of working I noticed that my remote viewing for the CCTV was not working. On checking the router settings I saw that the router had defaulted to no settings at all. Changing it back to PPPoE did not work since the page would not render completely. Resetting to Factory settings also did not work. However simply switching off the router and restarting it worked. I let it go then. The same thing happened again within a day or two. Each time restarted the router seemed to solve the problem, however temporarily. 
 
I have the SPI firewall enabled also I have application port forwarding set for HTML port 80 forwarding to say port 1234.

View 2 Replies View Related

Linksys Wired Router :: Use BEFSR41 In Bridged Mode?

Jul 22, 2009

I cannot find any explicit instructions on this.  Maybe they're calling it other things or implying it in other settings. 
 
How do I configured a BEFSR41 to operate in bridged mode?

View 4 Replies View Related

Linksys Wireless Router :: Using WAG120N In Bridged Mode With EA4500

Sep 30, 2012

I'm trying to use my WAG120N router as a modem only/Bridged Mode and I've managed to enter all my settings needed on the WAG120N which is the Encapsulation to Bridged Mode Only, QoS to UBR, Type Of Connection to LLC, VPI and VCI to 0 and 35, DSL Modulation to Multi mode.On the EA4500's end I've entered my Usrname and password in the Internet settings and configured for PPPoE.

View 8 Replies View Related

Linksys Wireless Router :: Can't Connect To Cisco EA4500 In Bridged Mode

Feb 20, 2013

I put the ea4500 on Bridged mode, and now I cant connect!I know I have to put the new ip address, and when I do I choose direct conect, it ask me for a password, I put the password, I click to connect, and then it just sits there in waiting....

View 9 Replies View Related

Linksys Wireless Router :: EA4500 In Bridged Mode - Nothing Appears On Screen

Nov 2, 2012

EA4500 in bridged mode and I can log in the the CCC account but nothing appears on the screen. I was able to see the settings, etc with the previious firmware. I reset the router and tried different browsers, PC, etc. Now running Ver.2.1.39.144146.

View 9 Replies View Related

Linksys Wireless Router :: Ea3500 Bridged Mode And Windows Network Drive?

Apr 5, 2013

I'm runing an ea3500 in bridged mode, classic configuration, firmware 1.0.30 build 126544. I got ftp working for my usb attached wv delements drive , but it is totally invisible in windows (except for ftp of course).I read in an older post that the usb drive in certain situations does not work (independent of disk manufacturer/type and such) and for certain configurations the ftp option might work but the windows mapped network drive doesn't , does that still apply? does it apply to bridged mode ?

View 1 Replies View Related

Linksys Cable / DSL :: Add Several Vpi / Vci To X2000?

Nov 22, 2012

How can i add several vpi / vci to my Linksys x2000 ?

View 7 Replies View Related

Linksys Cable / DSL :: Set Up PC Static IP With X2000

Dec 1, 2012

Just picked up a X2000 and Cisco connect configured my connection, and assigned an IP to my desktop pc.I configured my PC back to a Static IP which is outside the DHCP range in the X2000, and all seems to be working ok..now looking in the web-based X2000 setup screen my pc is no longer listed as a client...so should I manually add it as a client and assign the IP & MAC address in the Cisco setup or is this not necesary.?

View 5 Replies View Related

Linksys Cable / DSL :: X2000 3 Ports Not Enough

Jul 4, 2012

I have the X2000. It has 3 ports. I need 4. I also have the WRT160N V3 router which has 4 ports. Is there a way to use this router with the X2000 to get the 4 ports I need ? If not, what are my other options to get 4 ports ?

View 2 Replies View Related

Linksys Cable / DSL :: X2000 Can't Get An Ip Address Via O2

Nov 3, 2011

I've tried everything to get this to produce an i.p address but to no avail.I check with my ISP (o2/BE) they told me all my settings are correct it syncs but just does not pick up an IP address.

View 6 Replies View Related

Linksys Cable / DSL :: X2000 Power Led Is Red

Jun 27, 2012

linksys x 2000 modem unfortunately, when I turned the modem on today, the power light which normally was white became red.I tried all the ways I knew, such as restarting in 5 or 30 seconds intervals but unfortunately it didn't work

View 3 Replies View Related

Linksys Cable / DSL :: X2000 Will Not Connect To ATT?

Jan 31, 2013

Trying to replace old modem with the X2000 but it will not connect to the internet, my provider is ATT DSL.

View 2 Replies View Related

Linksys Cable / DSL :: Cannot Get X2000 To Connect To ISP

Oct 14, 2011

I cannot get my X2000 to connect to my ISP in the UK. From what I've read elsewhere I'm not the only one but I need to determine whether this is a router support issue or ISP.

View 9 Replies View Related

Linksys Cable / DSL :: WAG200G - Create LAN Bridged To Internet By Wireless

May 7, 2012

I have a WAG200G as my ADSL modem and wireless access point.  I would like to build two small wired networks that are remote from the location of the wireless access point (i.e. where my telephone line comes in) so that I can connect several network cabled devices in each location (e.g. NAS drive, TV, games consoles etc).  I cannot run network cables to these locaations but believe that I can bridge them via the wireless.  At a pinch, I could have only one cabled sub-network but would prefer two.

View 4 Replies View Related

Linksys Cable / DSL :: How To Change The Frequency On X2000

Apr 12, 2012

 How to change the frequency on X2000

View 1 Replies View Related

Linksys Cable / DSL :: X2000 DSL Connection Keeps Dropping?

Feb 1, 2012

I installed my new X2000 a couple of days ago and my ADSL connection drops several times a day. Sometimes it will stay connected for a few minutes and other times it will stay connected for several hours. The only way to get it connected again is to reboot.I have used 2 other routers (D-Link DIR-300 and BT Home Hub 3.0) on the same line and haven't had any disconnection issues with them, so the problem must be a hardware/software fault on this router or I have set it up incorrectly.Judging by a number of posts I found online, there seems to be a general problem with DSL connections dropping on the X2000, especially on earlier firmware versions. I have subsequently upgraded to the latest firmware (Ver.2.0.01 (Build 4)), reset and reconfigured twice, but nothing has worked so far.Unless I can get this working in the next few days I am going to have to return it, which is a shame because the performance of the router is great when it's working!Would someone be able check I have configured the DSL settings on the router correctly?
 
DSL SettingsEncapsulation: RFC 2364 PPPoAMultiplexing : VCAutodetect: DisableVPI: 0VCI: 38Modulation: MultimodeMTU: 1400

View 6 Replies View Related

Linksys Cable / DSL :: Some Devices Can't Connect To X2000

May 25, 2012

I have been setting up my new Cisco X2000 wireless router recently and I have it working fine for my desktop/laptops and even the PS3, however for some reason when you try to use the wireless on some of the other computers in my house it doesn't work unless you are using a wireless guest account.

View 2 Replies View Related

Linksys Cable / DSL :: X2000 Internet Is Half Going

Aug 12, 2012

So its the 3rd day of my nightmare to set up this cisco ADSL router...
 
Status: 
Setup: 
DSL connection:

 So I live in Ireland and im on Smart telecom ISP,  Basicly the internet is half going - like skype is going and i can chat with my contacts, cisco.com page is going but really SLOW, google.com page is going until search, speedtest.net page is going until the mesure thing facebook loads like in 10min.. a lot of pages dosent even go...From main telephone socket to the router is only 2.5m telephone cable(NO HOME PHONE) so no splitter or extension... (Changing the MTU dosent change anything...only if i set it on auto then w7 shows that internet is connected, skype works but no pages at all is loading and is dropping with timeout error.. if i set to manual then something loads on pages...) The cisco connect software does NOT do good because I can go until the username/pasword step, I input THE CORRECT details but he just sayes that he cant authenticate the username & pasw... and so i cant get past that step and the programm is no good.... only way is to set up with 192.168.1.1!

View 4 Replies View Related

Linksys Cable / DSL :: Get Max Network LAN Speed From The X2000?

Apr 22, 2012

How can I get Max network LAN speed from the X2000.I am connecting with a Macbook and an iMac both with N speed aiport cards.When checking the network speed through mac 'Network Utility' it is only getting 130 Mbps.Should it be getting closer to 300 Mps?

View 3 Replies View Related

Linksys Cable / DSL :: Cannot Access Webservers In LAN With X2000

Sep 18, 2011

I run a X2000 router for some weeks and it works properly basically - with one exception.WIFI attached devices (Win7, Vista, Android) can go to the internet without having any problem. But they cannot access my local servers (Media-Server, Storage server). I access with normal settings (not the guest) but the behavior is similar to what I expected from the guest-WIFI: protect resources in LAN.Anyway, for historical reason I have also another WIFI Hotspot in the LAN what is connected to the X2000 via cable. If the same devices connect to this hotspot, everything works fine. So the problem isn't caused by the servers.

View 9 Replies View Related

Linksys Cable / DSL :: X2000 Drops Dsl Connection

Nov 30, 2011

I'm having trouble with my Linksys X2000 modem/router to stay connected to internet. I have tried upgrading the firmware & changing my ip address, but still with no success.The router part is staying connected, but the dsl will drop off. I have to unplug to get it up and working again.

View 9 Replies View Related

Linksys Cable / DSL :: Line Status On X2000?

Jun 30, 2012

I just bought a new wireless modem router Linksys X2000 And I couldn't find the line status like SN margin and line attenuation and so on [URL]
 
how to access my ADSL line status

View 2 Replies View Related

Linksys Cable / DSL :: Monitor DSL Traffic On X2000

Nov 29, 2012

I'd really like to be able to monitor DSL traffic on my X2000. SNMP is the logical way to do this; Looking at the source to the Management screen, it looks tantalizingly close, but the SNMP bits are commented out in the HTML.

View 4 Replies View Related

Linksys Cable / DSL :: X2000 Not Work With ITunes

Nov 1, 2012

I have a new X2000 v2 firmware 2.0.04. When I use it- itunes on my PC with seven don't work and give me error 8003.- the Apple Store on my iPad and on my iPhone don't download or upgrade the application.- itunes on my macbook air with mountain lions don't work and give me error 8003.- the download in ftp are very slowIf I use my old AG2241V2 all work fine.I have replicated the configution of old router on the new as far as possible but don't work.

View 3 Replies View Related

Linksys Cable / DSL :: X2000 Split Internet Bandwidth

Oct 29, 2012

I have linksys X2000 modem and linksys WAG 200G modem I can use them both if needed I want to share my internet with my brother on our house But I want each one of us to have equal bandwidth ( speed ) How can I do this using those devices.

View 4 Replies View Related

Linksys Cable / DSL :: DHCP Replay X2000 Not Work

Sep 15, 2012

Here my network.dsl provider-->d-link modem (dhcp server, 192.168.1.1)-->X2000 (dhcp replay, 192.168.2.1(LAN IP))--> My laptop - X2000 config: dhcp replay: 192.168.1.1, LAN1 from d-link to WAN x2000 (blue rj45), X2000 have ip address from d-link. but my laptop can not receive ip address. X2000 is not gateway modem because it stuck after 1 day work. Can access to Web config page and internet.

View 4 Replies View Related

Linksys Cable / DSL :: Lost Disc To X2000 Gateway

Jul 10, 2012

I lost the disc to my X2000 gateway. Is there a download site for the software?

View 1 Replies View Related

Linksys Cable / DSL :: X2000 Losing Internet Connection?

Nov 14, 2011

I recently purchased at Linksys X2000 Router/dsl modem, I ran the setup and everything works fine except for when I am trying to play games online with one device and  surf the web on another device it keeps kicking one or both devices offline, but if only one of them is on it works fine.I have AT&T dsl and I have checked all my setting and the router was setup by linksys Cisco Connect program but it still gives me this issue.Is there anything I can do to fix this? My old WRT54G Router and AT&T dsl modem did not have this problem.

View 9 Replies View Related

Linksys Cable / Dsl :: X2000 Connection To Protected Wifi?

Oct 22, 2012

I try to connect my mac via WiFi I got connection timeout; with my android it keeps trying to connect without success (I didn't change passwords or anything these days).If I choose to connect via guest network everything goes fine.The only way to make it work as expected is to reboot the router.it's a X2000 with latest firmware (2.0.3)?

View 4 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved