I'm having trouble with my Linksys X2000 modem/router to stay connected to internet. I have tried upgrading the firmware & changing my ip address, but still with no success.The router part is staying connected, but the dsl will drop off. I have to unplug to get it up and working again.
View 9 Replies
I recently installed a Cisco X2000. Several PCs running Windows XP Pro connect wirelessly. Also, we have an Android device and iPhone connected to the wireless network. We have a network printer and network drive connected via wires to the router. Most of the time the router and cable modem features work well. However, every so often all devices lose wireless signal simultaneously. It is not possible to reconnect to the X2000 unless I unplug the X2000 and plug it back in. After this reboot, we can connect again. Obviously, this is quite frustrating. By the way, we get acceptable signal strength after the X2000 locks out however none of the devices (computers or phones) are able to connect.
View 1 Replies View RelatedI installed my new X2000 a couple of days ago and my ADSL connection drops several times a day. Sometimes it will stay connected for a few minutes and other times it will stay connected for several hours. The only way to get it connected again is to reboot.I have used 2 other routers (D-Link DIR-300 and BT Home Hub 3.0) on the same line and haven't had any disconnection issues with them, so the problem must be a hardware/software fault on this router or I have set it up incorrectly.Judging by a number of posts I found online, there seems to be a general problem with DSL connections dropping on the X2000, especially on earlier firmware versions. I have subsequently upgraded to the latest firmware (Ver.2.0.01 (Build 4)), reset and reconfigured twice, but nothing has worked so far.Unless I can get this working in the next few days I am going to have to return it, which is a shame because the performance of the router is great when it's working!Would someone be able check I have configured the DSL settings on the router correctly?
DSL SettingsEncapsulation: RFC 2364 PPPoAMultiplexing : VCAutodetect: DisableVPI: 0VCI: 38Modulation: MultimodeMTU: 1400
I recently purchased at Linksys X2000 Router/dsl modem, I ran the setup and everything works fine except for when I am trying to play games online with one device and surf the web on another device it keeps kicking one or both devices offline, but if only one of them is on it works fine.I have AT&T dsl and I have checked all my setting and the router was setup by linksys Cisco Connect program but it still gives me this issue.Is there anything I can do to fix this? My old WRT54G Router and AT&T dsl modem did not have this problem.
View 9 Replies View RelatedI try to connect my mac via WiFi I got connection timeout; with my android it keeps trying to connect without success (I didn't change passwords or anything these days).If I choose to connect via guest network everything goes fine.The only way to make it work as expected is to reboot the router.it's a X2000 with latest firmware (2.0.3)?
View 4 Replies View RelatedI just installed the X2000 and managed to get my Win7 Home Premium to connected to the Internet and also one wireless device. I previously had just a modem. Sometimes, when my PC is up and running, I want to disconnect it from the Internet and later connect again. There is an icon on the lower right of my toolbar which, with my old modem, allowed me to connect and disconnect but it seems to know only about the old modem. Basically it operated by starting the sequence: All Control Panel Items>Network Connections>Broadband Connection. Now this function does work; it tries to connect (through "WAN Miniport (PPPOE)") and gets "Error 651: The modem (or other connecting device) has reported an error". Can you tell me what where is the program that seems to start the Internet connection for the X2000 and if I can change parameters for the Win7 "Broadband Connection" to use the X2000? Perhaps the parameter "Connect on Demand" in the "Basic Setup" of the X2000 is involved?
View 9 Replies View RelatedLinksys x2000.Is it possible to use ADSL port as a main internet connection and to use WAN port as a backup internet connection?
View 1 Replies View RelatedHaving the issue for over a year now, I'm wondering why there isn't a fix for the mentioned connection drops of the WAG200G? I'm on the newest firmware now (1.01.08(3)) but still every so many minutes: bam, lost connection.
View 9 Replies View Relatedmy WAG160Nv2 drops the connection each day at the same hour (4:20pm to 4:40pm aprox.)I think that is because my ISP don't give me a static IP address and the connection must dropped once a day. in my old router I could put the time for the drop. I don't find something similar in the WAG160Nv2.
View 2 Replies View RelatedI have a WAG160N v2 and a UK Online broadbad account, windows xp. The connection intermittmently drops out, approx 15-30 times per day. I have spoken to my ISP and had the line checked (no packet loss issue), checked the settings on the router against my ISP and also updated the router firmware all with no improvement.
View 2 Replies View RelatedFrom time to time, when I wake up an specific station from sleep mode, the router loses its connection with Internet. It still has the line synced, but there is no Internet connection.I still can access the router through browser though. If I hit "connect" to establish a manual connection, it does not work. I have to switch the router off and on and wait for the whole process of syncing and connection, then I have Internet again.
I thought this could be something on that PC (old XP) sending some weird packet to router when I wake it up, but I tried with a newer PC (Win 7 64 bits) and the same problem persists. Also, this only happens when I wake up the PC. If it is off and I turn on, or if I restart, the problem does not happen.
The router (WAG120N) has an old firmware version (V1.00.12) because the latest available is buggy and had some problem with my ISP (limiting the bandwidth). However, I have this firmware for like 6 months and the problem only started 2 months ago.
This is a bit of a pain as the behaiviour is not consistent. whenever I connect to the Device webpage a number of things may happen
1. There is no connection - the page tries to load but never does. While this happens the router drops the ADSL connection and re-connects. I have to close the browser session and try again later. OR
2. The Browser session connects but at some point after the connection, say when I am trying to save changes or even just browsing through the config pages the session hangs, and again the router drops the ADSL connection and re-connects. I have to close the session and try again later.
I have noticed this happens when I use my OpenSuse 11.4 Linux Box using Firefox 5 or even using my Win 7 Box using IE9.
How can i add several vpi / vci to my Linksys x2000 ?
View 7 Replies View RelatedJust picked up a X2000 and Cisco connect configured my connection, and assigned an IP to my desktop pc.I configured my PC back to a Static IP which is outside the DHCP range in the X2000, and all seems to be working ok..now looking in the web-based X2000 setup screen my pc is no longer listed as a client...so should I manually add it as a client and assign the IP & MAC address in the Cisco setup or is this not necesary.?
View 5 Replies View RelatedI have the X2000. It has 3 ports. I need 4. I also have the WRT160N V3 router which has 4 ports. Is there a way to use this router with the X2000 to get the 4 ports I need ? If not, what are my other options to get 4 ports ?
View 2 Replies View RelatedI've tried everything to get this to produce an i.p address but to no avail.I check with my ISP (o2/BE) they told me all my settings are correct it syncs but just does not pick up an IP address.
View 6 Replies View Relatedlinksys x 2000 modem unfortunately, when I turned the modem on today, the power light which normally was white became red.I tried all the ways I knew, such as restarting in 5 or 30 seconds intervals but unfortunately it didn't work
View 3 Replies View RelatedTrying to replace old modem with the X2000 but it will not connect to the internet, my provider is ATT DSL.
View 2 Replies View RelatedI cannot get my X2000 to connect to my ISP in the UK. From what I've read elsewhere I'm not the only one but I need to determine whether this is a router support issue or ISP.
View 9 Replies View RelatedHow to change the frequency on X2000
View 1 Replies View RelatedI have been setting up my new Cisco X2000 wireless router recently and I have it working fine for my desktop/laptops and even the PS3, however for some reason when you try to use the wireless on some of the other computers in my house it doesn't work unless you are using a wireless guest account.
View 2 Replies View RelatedCan the 2 WAN ports be connected at the same time to provide failover and if so can this be configured for priority/ delay etc.A user has a very poor ADSL service so also has a bidirectional satellite link. Due to the latter's high latency I don't want it dropping that connection too quickly.
View 1 Replies View RelatedSo its the 3rd day of my nightmare to set up this cisco ADSL router...
Status:
Setup:
DSL connection:
So I live in Ireland and im on Smart telecom ISP, Basicly the internet is half going - like skype is going and i can chat with my contacts, cisco.com page is going but really SLOW, google.com page is going until search, speedtest.net page is going until the mesure thing facebook loads like in 10min.. a lot of pages dosent even go...From main telephone socket to the router is only 2.5m telephone cable(NO HOME PHONE) so no splitter or extension... (Changing the MTU dosent change anything...only if i set it on auto then w7 shows that internet is connected, skype works but no pages at all is loading and is dropping with timeout error.. if i set to manual then something loads on pages...) The cisco connect software does NOT do good because I can go until the username/pasword step, I input THE CORRECT details but he just sayes that he cant authenticate the username & pasw... and so i cant get past that step and the programm is no good.... only way is to set up with 192.168.1.1!
How can I get Max network LAN speed from the X2000.I am connecting with a Macbook and an iMac both with N speed aiport cards.When checking the network speed through mac 'Network Utility' it is only getting 130 Mbps.Should it be getting closer to 300 Mps?
View 3 Replies View RelatedI run a X2000 router for some weeks and it works properly basically - with one exception.WIFI attached devices (Win7, Vista, Android) can go to the internet without having any problem. But they cannot access my local servers (Media-Server, Storage server). I access with normal settings (not the guest) but the behavior is similar to what I expected from the guest-WIFI: protect resources in LAN.Anyway, for historical reason I have also another WIFI Hotspot in the LAN what is connected to the X2000 via cable. If the same devices connect to this hotspot, everything works fine. So the problem isn't caused by the servers.
View 9 Replies View RelatedI have been trying this for ours and need to get it to work for a small branch office so I can get their cisco device connected and phones working.
The device works fine if I assigned it an IP address but the minute I set bridge mode only and assign the static IP to my system then nothing works. I have the latest firmware.
I just bought a new wireless modem router Linksys X2000 And I couldn't find the line status like SN margin and line attenuation and so on [URL]
how to access my ADSL line status
I'd really like to be able to monitor DSL traffic on my X2000. SNMP is the logical way to do this; Looking at the source to the Management screen, it looks tantalizingly close, but the SNMP bits are commented out in the HTML.
View 4 Replies View RelatedI have a new X2000 v2 firmware 2.0.04. When I use it- itunes on my PC with seven don't work and give me error 8003.- the Apple Store on my iPad and on my iPhone don't download or upgrade the application.- itunes on my macbook air with mountain lions don't work and give me error 8003.- the download in ftp are very slowIf I use my old AG2241V2 all work fine.I have replicated the configution of old router on the new as far as possible but don't work.
View 3 Replies View RelatedI have linksys X2000 modem and linksys WAG 200G modem I can use them both if needed I want to share my internet with my brother on our house But I want each one of us to have equal bandwidth ( speed ) How can I do this using those devices.
View 4 Replies View RelatedHere my network.dsl provider-->d-link modem (dhcp server, 192.168.1.1)-->X2000 (dhcp replay, 192.168.2.1(LAN IP))--> My laptop - X2000 config: dhcp replay: 192.168.1.1, LAN1 from d-link to WAN x2000 (blue rj45), X2000 have ip address from d-link. but my laptop can not receive ip address. X2000 is not gateway modem because it stuck after 1 day work. Can access to Web config page and internet.
View 4 Replies View RelatedI lost the disc to my X2000 gateway. Is there a download site for the software?
View 1 Replies View RelatedI've just bought all-in-one router X2000.And I found that in the parental control [ADD] windows does not show every device's name.It shows only 3 of 20 devices (ex. My-nb, PCaccount, PChuman, but the others show "Network device").
View 1 Replies View Related
