Cisco Wireless :: Replace 352 Bridged Network With 1552s?
Mar 20, 2012
I have a question concerning replacing a 352 bridged network with 1552 mesh access points. Theoretically, imagine a centralized 352 with an omnidirectional antenna that is linked to multiple 352's with yagi antennas in a hub-spoke fashion. If this central 352 is replaced with a 1552 access point, will the existing Yagi's be able to talk to the 1552? I understand that the Yagi's AP's should be replaced with 1552's as well (thus forming a mesh network as the 1552s are designed to do) but for the sake of theory please assume the 'spoke' 352s will not be replaced. I have the understanding that the 1552s communicate over the 802.11a for the backhaul so I'm thinking this would cause some issues with the 352's.
View 2 Replies
ADVERTISEMENT
Aug 9, 2011
I have a wireless N router (DIR-655) in bridge mode connected to a TWC combo modem/wireless G router. I have Tversity media server running on a computer connected to the TWC, but my PS3 which is connected wirelessly to the TWC combo can't see Tversity. What am I missing? Do I need to forward some port from somewhere? FYI, I'm set-up this way so my N router can deliver full N speed, and my G devices connect to the slower TWC router. Everything sees the internet with no problem. Also, to note that devices connected to the D-link can see Tversity, but devices connected to the TWC cannot see Tversity
View 4 Replies
View Related
Apr 5, 2013
I'm runing an ea3500 in bridged mode, classic configuration, firmware 1.0.30 build 126544. I got ftp working for my usb attached wv delements drive , but it is totally invisible in windows (except for ftp of course).I read in an older post that the usb drive in certain situations does not work (independent of disk manufacturer/type and such) and for certain configurations the ftp option might work but the windows mapped network drive doesn't , does that still apply? does it apply to bridged mode ?
View 1 Replies
View Related
Dec 20, 2012
I am trying to setup a remote PC over a wireless access Point/Bridge to our FIOS router. Pic of setup is shown below. Everything is connected, there are no errors or security warnings shown in the ActionTec MI424 router. The RemotePC IP shows up as an Active Ethernet client in the Router config app. Moreover, I can run the connectivity test from the router app to the RemotePC and it passes that, and I can PING from the RemotePC to the Router. Yet I cannot reach the Internet from a Browser on the RemotePC (192.168.1.75). I am using (2) DLINK DAP-1522 Access Point/Bridge units and they have worked as expected. I set the Router log to list any blocked IP traffic as well, and it does not show anything being blocked from the RemotePC (192.168.1.75). So why can't I reach the Internet from the RemotePC? Seems like a gateway problem or I need to make some config changes in the Router.
View 2 Replies
View Related
Mar 6, 2013
I am attempting to replace an existing printer on the network and keep running into trouble. I am sure at this point it is my frustration with it that is not allowing me to see what I am doing wrong. I attempt to just swap it out with exsiting printer and it grabs an IP address and then when I try to enter that IP address into my broswer to access the printer to give it the permanent one from printer I am replacing I cannot get to the printer.
View 6 Replies
View Related
Sep 29, 2012
I think that my ISP is throttling my bandwidth at the modem . how access full available bandwidth.When the technician installed the fibre optic line and then the modem, he showed me an amazing 77MB/s (about 600Mbps) before the modem!!But after the technician left these were the test results after the router:
1) SpeedTests.net:
averages, after router, show: UP between 56/60Mbps & DN 45/75Mbps
2)Local Server Speed Test:
average: UP 45Mpbs & DN 170Mbps
A Japanese Internet savvy guy explained that NTT East throttles the available bandwidth at the building by specific apartment/modem settings related to individual contract bundles. I signed up for the top bundle: TV, Phone and Internet connections.This is my Hardware/ software setup:
OS: Win7,
Line specs:
Line type: IEC60874-14
Connector type: SC
Core across: 9 micrometers
Clad across: 125 micrometers
ITU-TG-652
NTT East fibreoptic TV/Internet/Telephone bundle (100Mbps best effort) Hikari Next Family Type but 10Mbps is considered within parameters
Asahi ISP Internet contract
Modem:
GE-PON (WAN+Coaxial TV antenna)
"SCM-GE-PON-<H>A GV-ONU D<1>" model
Router:
RT-S300HI (4 Giga ports + 1 phone)
Router & Modem have Japanese firmware which I cannot understand and, according to the NTT East, I must rent both modem and router from them and "will not support any other modem/router setup".I could not understand if it was because of technical or contractual limits.
I have tried to test my throughput after the modem but I could not figure out where the DNS, IP, WAN etc strings of numbers should go and, in the end, I simply cannot connect to the internet from my laptop directly to the modem so I cannot perform the same speed tests after the modem.
View 12 Replies
View Related
Sep 19, 2012
Is it possible to build two separate bridged connections from one "base"?
I'd need to connect to two other buildings which luckily happen to be quite on the same direction (antennawise). how to configure this into the devices I call "base", "building1" and "building2". The first building is about 50 meters and the other about 120 meters away. 11Mbps would be adequate for both. A some kind of encryption would be needed.
View 1 Replies
View Related
Dec 24, 2010
I am have a lot of difficulty getting my WET610N to connect to my WRVS4400N. I have tried almost everything. I have some older PC's, as well as my PS3, that we use to use on the network and they only connect B/G. I have tried auto DHCP and static IP on the bridge. It seems that the only way that the bridge works is by using the WPS function that the business class routers do not have.
View 1 Replies
View Related
Dec 10, 2011
I have 2 E4200's . One is connected to my ADSL Modem as DHCP and the other one is Bridged to the DHCP. I'm trying to connect to my E4200 that is set as Bridged. I am able to connect to my E4200 that is set as DHCP, but I cannot connect to the E4200 that is connected to that DHCP as Bridged.
How can I connect to that bridged E4200 because I want to upgrade the Firmware of the Bridged E4200?.
View 1 Replies
View Related
Nov 10, 2012
had a EA4200 about a year now, no probs, very stable, i'm thinking about getting a EA6500, for better coverage, iPhone apps, etc, would like to use my EA4200 in bridge mode from a EA6500, I'm a fairly new to networking etc, i'm assuming when the EA4200 is bridged, it will act like a repeater connected by cable, with same SSID ?
View 7 Replies
View Related
Feb 20, 2013
I put the ea4500 on Bridged mode, and now I cant connect!I know I have to put the new ip address, and when I do I choose direct conect, it ask me for a password, I put the password, I click to connect, and then it just sits there in waiting....
View 9 Replies
View Related
Jun 26, 2012
I have a WLC 5508 with LWAP 1242 with wireless bridges connected to the APs I cannot get DHCP to pass through the bridge to the PC connected to the bridge.
View 5 Replies
View Related
Sep 30, 2012
I'm trying to use my WAG120N router as a modem only/Bridged Mode and I've managed to enter all my settings needed on the WAG120N which is the Encapsulation to Bridged Mode Only, QoS to UBR, Type Of Connection to LLC, VPI and VCI to 0 and 35, DSL Modulation to Multi mode.On the EA4500's end I've entered my Usrname and password in the Internet settings and configured for PPPoE.
View 8 Replies
View Related
May 7, 2012
I have a WAG200G as my ADSL modem and wireless access point. I would like to build two small wired networks that are remote from the location of the wireless access point (i.e. where my telephone line comes in) so that I can connect several network cabled devices in each location (e.g. NAS drive, TV, games consoles etc). I cannot run network cables to these locaations but believe that I can bridge them via the wireless. At a pinch, I could have only one cabled sub-network but would prefer two.
View 4 Replies
View Related
Dec 28, 2012
I have just recently replaced my Netgear router with an EA3500 and have it bridged t an Airport Express. From there I have an ethernet cable attached to an AV receiver (Pioneer 1021k), but all to often now with this new router to use any of the features of the receiver ie Airplay, iOS app remote, I must restart the router EVERY time. This is frustrating because the these issues were never present with the netgear router.
View 9 Replies
View Related
Nov 25, 2012
I have an e4200v1 in bridge mode (LAN IP 192.168.1.2) connected via its WAN port to a LAN port on the primary router at 192.168.1.1.
Guest Wireless works perfectly in Ver. 1.0.04 build 11 but not in Ver. 1.0..05 Build 7.
View 9 Replies
View Related
Sep 23, 2012
I want to set up an E1200 as a wireless access point for guests, and ordinarily I'd be happy to connect it LAN-to-WAN and have it create its own subnet, but I need to connect one office PC to it also because connecting the E1200 to the main gateway displaces that office PC from the last Ethernet port on the main router.
So I disabled DHCP on the E1200 and connected it LAN-to-LAN. The modem is at a fixed, non-configurable address of 192.168.0.1/255.255.0.0 and the main router is at 10.0.0.1/255.255.255.0. I set the E1200 to a static IP of 10.0.0.12/255.255.255.0.The E1200's primary wireless connection works fine. The guest access connects, but it does not prompt for a password and web pages generate a "failed to load" sort of message.I temporarily connected the E1200 as the main router and re-enabled DHCP, though I kept the static IP of 10.0.0.12/255.255.255.0, and in this configuration the guest access worked. I observed that it connected via 192.168.33.1/guestaccess.cgi (or something very similar to that).
View 2 Replies
View Related
Feb 6, 2012
I'm trying to connect my Xbox 360 to Live by bridging my computer's wireless connection. I've done this before for a friend in a different city and it worked fine, and I felt very proud of myself for doing so. However when I try to connect here, the modem won't assign my Xbox an IP address. I've been into ipconfig/all and tried to manually assign the same IP address to the Xbox but to no avail. Same deal with the alternate MAC address option.
To speed things along here's the readout from my ipconfig/all:
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersSamsung>ipconfig/all
[Code].....
View 2 Replies
View Related
Nov 2, 2012
EA4500 in bridged mode and I can log in the the CCC account but nothing appears on the screen. I was able to see the settings, etc with the previious firmware. I reset the router and tried different browsers, PC, etc. Now running Ver.2.1.39.144146.
View 9 Replies
View Related
Feb 1, 2013
I've set up PPPoE on my EA4500 router with a Vigor 120 modem in bridged mode and it says an internet connection is established, but the connection is extremely slow on all my devices. When I run the speed test within the EA4500 firmware it appears fine, but I cannot load any web pages on my laptop or other decives because the connection is so slow. The connection is slow with both wired and wireless connections. I've tried changing the MTU settings with no success. I've also tried using a different router and connecting the modem directly to my laptop and using PPPoE within the laptop and these both work fine, so I think it's clear there is a problem with the EA4500 router itself.
I'm just using the Vigor 120 to authenticate and connect to the internet itself, with the router in DHCP automatic configuration mode. I think this is causing a double NAT.
View 9 Replies
View Related
Feb 17, 2012
I have a HP DV6000 Laptop. The wireless coverage is not very good and I was thinking of upgrading the Wireless card to something better. The current card is HP Pavilion DV9000 PCI-Express Wireless WIFI Card 802.11a/b/g 441075-001 by HP. Is it even possible to install another card in the laptop or does HP limit what you can put in this laptop
View 3 Replies
View Related
Sep 26, 2011
can you replace the standard wired modem provided by your ISP with a wireless/wifi modem yourself?
View 4 Replies
View Related
Oct 6, 2012
I'd like to replace my 4402 Wireless controller with a new 5508. I have migrated the exact configuration from my 4404 controller to the 5508 and they are both running the same version of code. I'm worried that if I replace the 4402 with the 5508 controller, the Access Points will not rejoin to the new controller or they will join but will have lost their configuration e.g. AP Name/location etc etc. AP models registered to the existing controller are 1131, 1142 and 3502. I am also using Cisco WCS.
As long as the new controller has the exact same configuration, is it possible to replace the 4404 with the 5508? Will the existing Access Points join the new controller? Is there any other configuration required? I have read about doing this using mobility groups however would rather not if possible.
View 2 Replies
View Related
Mar 12, 2013
how can i replace my wlc2504 to a WLC5508 without disconnecting everybody, i have 3 SSID, on different VLAN.. I want the WLC5508 to be the main WLC, so i can remove the 2504 from the network. On the WLC5508, it will be the same configuration of the 2504. Is there a procedure or a wiki on such operation?
View 8 Replies
View Related
Jan 4, 2013
I am looking to replace my current WAG54GS Gateway with the EA6500. Problem is the new one does not have a built in ADSL2+ modem (I am in the UK and my ISP is Demon Internet). I therefore need to purchase a separate Modem to connect to the router.
View 9 Replies
View Related
Sep 6, 2011
I need to replace a dying Netgear FWAG114 wireless router, and the E4200 gets good reviews so I've been looking into it. I'm a software developer running 6 servers plus 3 laptops and 5+ other devices (iPad, Wii, Droid phones, BluRay...). I prefer to use a trusted PC list (enter MACs for all trusted devices) rather than WEP or WPA - is this available with the E4200?
I don't need VPN, but I do run a number of web servers, app servers and databases, so port forwarding is important - I notice the E4200 provides port range forwarding and single port forwarding - I assume this replaces the Rules and Services feature in Netgear - right?
Do you see any potential problems, given my needs, in using the E4200?
View 2 Replies
View Related
Jul 13, 2012
I own an HP Pavilion dv6 Notebook PC and recently purchased a Cisco E1500 to replace my aging WRTG54 wireless router. Since installation of the new router I keep getting dropped from my LAN and the internet with "connectivity issues" ... this only occurs on my notebook PC and not the other wireless devices I have in my home. I’ve done some searching on the internet and this seems to be a generic problem with the Broadcom 802.11b/g/n card the notebook uses. I have 2 questions:
1) Is there an easy way to adjust either the card or the router to deal with these issues and if not then
2) what is the best notebook card to replace the Broadcom with to assure these issues go away.
View 9 Replies
View Related
Feb 24, 2013
Region : Malaysia
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
ISP : TM
I am having difficulty setting up the W8968 to replace the router given by TM for the Unifi connection.I tried updating the firmware of the modem router and used quick setup to configure the device as a wireless router using PPPoE, but still couldn't connect to the internet using the WAN port.I noticed there was a guide for TD-W8960N to set up TM Unifi but the web interface is too different from the W8968 interface.
View 1 Replies
View Related
Apr 18, 2011
I'm a Cisco newbie and I'm in the following situation:
1>The router (867) must connect to my ISP in 1483 bridged (2684 bridged) mode, LLC, VPI/VCI 0/35
2>WAN IP will be assigned by ISP (DHCP)
3>No username and password required to establish the connection
4>MAC-Cloning is advised, not required
5>Firewall behind 867, WAN IP should be assigned to WAN interface firewall, connection established by 867
6>867 router will be used as a switch, so no NAT required. NAT will be setup on the firewall
7>Connection type: Analog (annex A)
The required setup can be fixed by configuring the 867 in half-bridged mode, but I don't no how and I don't know exactly how to config the 867 in bridged mode.
First, it's even hard to setup a good bridged config.
version 15.1no service padservice tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryptionservice sequence-numbers!hostname router1!boot-start-markerboot-end-marker!logging buffered 51200logging console criticalenable secret 5 ****!no aaa new-modelmemory-size iomem 10clock timezone GMT 1clock summer-time GMT date Mar 30 2010 1:00 Oct 26 2035 1:59!!no ip source-route!ip cefno ip bootp serverno ip domain lookupip domain name domain.local!!!!username admin privilege 15 secret 5 ***!!ip tcp synwait-time 10ip ssh time-out 60ip ssh authentication-retries 2!!!!!!!interface ATM0 no ip address no atm ilmi-keepalive!interface ATM0.1 point-to-point pvc
[code].....
View 10 Replies
View Related
Dec 5, 2012
Connecting the sip trunk provider modem and my network on the rv042 and connect my phone system on it so he can access both my sip trunk and internet connection.
I have 1 WAN modem from my sip trunk provider connected to the first WAN interface in the RV042.My network is connected to the second WAN interface programmed as a transparent bridge to link both lan segments together
however the link between the WAN2 interface and the network seems to go up and down and i cant ping my network gateway from a pc connected to the switchport of the RV042.
all i need is internet access to the phone system for email notification via a SMTP server.
View 1 Replies
View Related
Apr 28, 2010
I have a Linksys WRT54G router; have a cable internet connection through the router; and two wired desktops, one running Vista (32-bit) and the other XP. I would like to replace the XP machine with a wired desktop running Windows 7 (64-bit).
View 8 Replies
View Related
Jul 10, 2011
I would like to convert my cable modem Cisco epc3825 (bridge only), and thus can not function as a router. Before if I could, but my Internet Service provider has updated the firmware epc3825 and I can not pass it on to cable modem (bridge only).
View 2 Replies
View Related
Mar 23, 2012
I recently got the sbg6580 an want it to work in bridged mode with my linksys wrt54g router. The problem is everything that is connected wirelessly like my Xbox or iPhone are connected to the Internet but my desktop pc which is a wired connection won't connect to the Internet.When I directly connect the modem to my desktop it works fine.
View 1 Replies
View Related
