How can I configure VPN connection between Cisco RV042 and Fritz!box 7170?I can establish VPN channel with Linksys RV042 with firmware 1.3.12.6-tm. When I set the same setting to Cisco RV042 (firmware v4.0.2.08-tm) VPN channel is not established.
View 1 RepliesI tried to configure two RV042 working together. [code] WAN2 of both Router1 and Router2 are unused (unplugged). However, the Host2 can never ping to Host1. So as to Host1. Should I need to configure the protocol binding for all the traffic to the WAN1?
View 3 Replies View Relatedconfigure ip-sec vpn tunnel between ASA5525x and RV042
View 5 Replies View RelatedI have a RV042 VPN Router with the latest firmware v4.2.1.02.This Router is connected to the main site by a VPN Tunnel.
Now, I like to configure some DHCP Option so I can put a IP Phone behind the RV042. The IP Phone should receive a IP by DHCP from the RV042 and of course, the IP of the Call Manager with the Option 150.
I can configure DHCP and it works fine but I can't find where I have or can configure Option 150.
I need configuring Cisco RV042 dual wlan and port forwarding for 2 servers web and dns in LAN
View 1 Replies View RelatedI've purchased a Linksys RV042 hoping I could connect my two ISP.Both of them are 1/1 Mb, first is DSL second PPPoE connection.The problem is that on system summary page it doesn't show me that second WAN is connected. Even when I trying to manually connect to Internet it doesn't work.
When this connection is in Load balance Mode, internet is very slow, sometimes it's even disconnected.
My question is:How to configure Load Balance properly?I've tried this page:
[URL]...
I have tried replacing a loaner RV082 V2 with an RV042 V3 router with firmware 4.0.4.02. All worked well, including the site to site VPN. However, in spite of the fact that I have ports 443 and 4125 forwarded to the server (192.168.2.10), we are unable to connect via RWW. There is no such problem with the RV082. What is different with the way we configure these V3 routers for port forwarding?
View 2 Replies View RelatedCisco RV042 Dual WAN VPN Router -how to configure dynamic DNS without having to use the pre-programmed DDNS companies that are populated by default if my DDNS company is not listed and you cannot manually enter another company that is not on the list?
View 1 Replies View Relatedhow i can configure the Cisco RV042 to access PPTP VPN Server (Witopia VPn) or other vpn servers.
View 1 Replies View RelatedIs there a way to set up a Site-to-site VPN between RV042 & Cisco 2911? I "googled" this and obtained a document, but it is not regarding Cisco 2911: [URL]
Routers are needed to setup it successfully. I have tried on both routers several configuration steps, no success...
Connecting the sip trunk provider modem and my network on the rv042 and connect my phone system on it so he can access both my sip trunk and internet connection.
I have 1 WAN modem from my sip trunk provider connected to the first WAN interface in the RV042.My network is connected to the second WAN interface programmed as a transparent bridge to link both lan segments together
however the link between the WAN2 interface and the network seems to go up and down and i cant ping my network gateway from a pc connected to the switchport of the RV042.
all i need is internet access to the phone system for email notification via a SMTP server.
I have successfully connected two RV042s to establish a VPN gateway to VPN gateway connection. I have the follow questions:
1. I would like to keep the VPN tunnel connection time indefinite. Is it sufficient by checking the "Keep-Alive" box on the VPN -> Gateway To Gateway -> Advance page? Or, I have to ping the RV042 periodically?
2. Do the "Phase 1/Phase 2 SA Life Time" (on VPN -> Gateway To Gateway page) settings have any impact on keeping the VPN connection time indefinite? What are the optimal values for them?
3. Is there an API, command, or script to replace a manual clicking on the "CONNECT" button to establish the VPN tunnel from the VPN -> Summary page? Or, is there a way to accomplish this at power up?
4. Is there a way to establish a VPN tunnel without going through login and clicking the "CONNECT" button? (Auto connect at power up?)
I have 2 WAN connection @ my office. One is the static IP from Reliance Network
The other connection of WAN is dynamic from AIR TEL...
When i logged into my router. I can see the dynamic IP from Reliance on WAN1 status. But on WAN2 is see everything as 0.0.0.0. The WAN2 configuration has been set to get the IP automatically...
I tried the other solution offered by one of the support guys, by turning on and off the modem, but that does not work...
Or do i need to change the WAN2 connection to be PPoE or something...
I have a RV042 VPN Router inside an ASA 5505 running version 7.2. I am attempting to connect from the outside to the RV042. I have read for 2 days now and tried everything I have found and had no success. I can connect from inside the network to the RV042 so I know that is setup correctly. I have found links on several posts to the official Cisco support documents but they make no sense to me. This is my first experience with a Cisco Firewall.
We also have a security camera network that we access externally and I have successfully set up the port forwarding for this. Here is my current running configuration. The inside ip address of the RV042 is 192.168.168.25. I had port 1723 forwarded, opened GRE, and have setup PPTP inspection. I have deleted the port forwarding at this point.
Result of the command: "show running-config"
: Saved
ASA Version 7.2(3)
hostname suite
domain-name hivermont.com
enable password vwiH3D2KQdqR57As encrypted names
interface Vlan1 name if inside
security-level 100
ip address 192.168.168.1 255.255.255.0
ospf cost 10
[code].....
I have an issue with Cisco RV042 i have two Internet access connection from my ISP one with 30Mbps and the other with 8Mbps.
i have 30Mbps in WAN1 and 8Mbps on WA2
my issue that i was connecting both of the WAN connections using DHCP mode and it was working fine and the ISP modem was terminating the PPPOE
now i decided to use PPPOE on the Cisco RV042 and change the ISP modem to bridge mode.
WAN1 is working were as WAN2 is not working.
i tried to factory reset, shift links, in all cases WAN2 if its on PPPOE does not go up.
i am using latest firmware from cisco.com.
My network consists of the following:
Office-RV042 with static IP ->SBS2003 (10.10.10.5/ 255.255.255.0)
Remote: BEFSR41 with Dynamic -> XP sp3 VPN client (192.168.3.x/ 255.255.255.248)
Within the RV042 I have enabled the PPtP server and assigned a user. No port forwarding enabled. All VPN passthroughs and firewall is enabled. DHCP server is disabled.I can establish a connection to the rv042 and ping PCs including the sbs domain server on the office side but am unable to browse any folders. When I attempt to access a network folder located on the office server I am prompted for a username/ password. Upon entering my domain credentials I get an error stating: "the user name you typed is the same user name you logged in with. That user name has already been tried. A domain controller cannot be found to verify that user name"
I have an RV082 and a RV042. I have been able to successfully establish a gateway to gateway vpn connection between them both, but both Routers unable to ping each other and I can't remotely administer each router through the VPN connection.
View 1 Replies View RelatedAt this moment I'm trying to connect 2 router rv042 and i received the following error message
(g2gips0) #23: ERROR: asynchronous network error report on eth1 for message to 190.199.164.144 port 500, complainant 190.199.164.144: Connection refused [errno 146, origin ICMP type 3 code 3 (not authenticated)]
in the other router i don't see any error . what would be the problem.
So here is my issue. I have two sites, each with a Linksys RV042 on thier site.
Site 1:
External: 142.142.142.142
Internal: 192.168.25.0/24
Site 2:
External: 143.143.143.143
Internal: 192.168.26.0/24
We have setup a site-to-site VPN between these sites, and all traffic is running back and forth without isse.
At Site 1 we have configured the Client VPN for use with the QuickVPN software. Again, for site 1, this is not an issue. We are able to access all internal resources at Site 1 without issue (expect for some DNS related problems).
The problem that we have is attempting to access Site 2 resources via the QuickVPN connection at Site 1. Even though they are not suppose to exist, we are able to ping 192.168.26.1-6 (which are ghost addresses likely created by the RV042's) but no actual systems on at Site 2.
I have added the Client VPN connection at Site 2, but it has the same problem accessing resources at Site 1.
Im able to create a gateway tunnel with two rv042 routers in different locations ( i can see the tunnel connected in the router) but the quick vpn utility is not working , i also tried to use the pptp as server as an alternative( im able to connect using windows connection to the pptp server but whenever I browse any of the four ip's allowed for the pptp server \10.0.0.200-204 it takes me to the documents of the local computer....I attached the configuration for one of the routers it is the same as the other end , just the information is flipped.
Message was edited by: Adrian Torres
we do have 2 Rv042, one in my office and one in my house.. in the office we do have static ip and at home none.. question is can i connect the two RV042?
View 1 Replies View RelatedI have some problems in my network with Gateway to Gateway Vpn Connection using two Rv042 routers.
I cannot ping the computers with static ip configuration.
In local an remote computers who have DHCP ip configuration i can ping each other .
I have a Cisco 1801 that I am trying to set up for my DSL connection. I have configured the router but when I try to access a web site I receive the Http 404 page cannot be displayed error. I have checked my DNS server on the router & I believe that I have configured it correctly? I am hoping that one of you more experienced individual can take a look & tell me where I might have gone wrong. I have included the current running-configuration for your viewing pleasure.
View 4 Replies View Relatedcofigure a ADSL2+ Conexion in an 1941 router.line protocol are up but didn't have ip adresse in my interface.[code] i don't know how i can find the probleme, and debug's comandes no show me anything.
View 3 Replies View RelatedI've just started styding for CCNA. Bought a router 871W recently and spent two days straight trying to configure internet connection with no luck! I use console port to do the configs and SDM/CCP. How to do simple internet connection configs. I googled everything but it's still confusing. I can't assing any IP to FA ports 0 - 3. I used VLAN instead. But all tutorials use FA0 and when I try to assign an IP to FA0 it gives me some L2 can't be assigned or something... :/ And I'm also confused what IP address should I use for WAN. I plugged the cable from Modem to PC's LAN port and wrote down some IP addresses which I think I'll have to use to configure the router for internet connection. And here they are:
ISP IP: 76.114.54.255
SUBNET: 255.255.248.0
GATEWAY: 76.114.48.1
DHCP: 69.252.97.4
DNS: 75.75.75.75
75.75.76.76
I'm trying to configure an 887VA for a pppoe ADSL2+ connection with no luck.I know the ISP requires pppoe (LLC), and the pvc is 8/35.
The CD light is on, and the line is up, but the 887 just won't connect
I have a problem to configure my connection SDSL.my router is SRP527W. my modem is Patton 3088. Do I need to update the ios? or there is a specific configuration of static IP ?
View 1 Replies View Relatedwhat will be the work around on this configuration.currently we have a Lease Line connection on serial interfaceISP <=SERIAL=>Router 2911<=ACCESS MODE=>Firewall(DATA DHCP SERVER located here, policy implemented here)<=TRUNK MODE=>CORE Switch(VLAN Assignment is here)<=TRUNK MODE=>ACCESS Switch(DATA and VOICE passess thru each ports)i am thinking to create a DHCP pool on the router to where my firewall should point to and from the DHCP pool it will point the internal network going to public network.
View 2 Replies View Relatedhow can i configure the SSL VPN users connexion to connecte from my remote PC (Windosws 7 32 & Internet Explorer
View 1 Replies View RelatedI've configured an srp541w router for a customer and successfully configured an IPSEC VPN connection with a Netopia router at a satellite office for the customer.
I cannot seem to find a way to configure either a PPTP VPN connection or QuickVPN connection for remote users. I did read something that stated that the router will only support either a site-to-site VPN or a QuickVPN connection, but not both at the same time.
I have a doubt. What I have to configure in my RV180 to make a VPN connection with Qvpn client. I created the user and if try to connect from the client I've recieved the message that is connected, but if I try to ping the RV180 local ip answer, but if I try to ping any other IP address of the VPN I can't. I think I would have something misconfigured but I don't know what is it.
View 4 Replies View RelatedThis is for an ASA 5505. I am trying to configure an AnyConnect and IPSec VPN connection and I think it's almost there but not quite yet. When I login from an outside network it gives me the following error for the SSL AnyConnect "The VPN client was unable to setup IP filtering" and "Secure VPN connection terminated by peer" for the IPSec. I previously had this working since Oct, but I was trying to modify it a little to accept LT2P for native Android VPN clients and that messed up everything that I had working perfectly. I checked everything as best as I could to try and match the previous settings but still can't get the darn thing to work. I am trying to also do Hairpinning, I want all VPN traffic to pass through this router... remote LAN and Internet traffic for times when I am at unfamiliar wifi hotspots and need to check email securely. I have included my running config. I also need to configure the ASA to accept native Android VPN connections. I read the most popular thread that worked for a few users but while doing those modifications that is where everything went downhill. T
: Saved
:
ASA Version 8.4(2)
!
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
[code]....
When it comes to configuring my new Linksys Cisco WRT120N router to my PPPoE connection. I've visited 192.168.1.1 but I'm not sure what to do next. So, I've got a PPPoE connection, static IP address, Linksys Cisco WRT120N router and a terrible ISP.
How to configure my new router so that I can start using the wireless for Internet access at home.