Cisco Routers :: RV042 - WAN2 PPPOE Connection
Jul 4, 2012
I have an issue with Cisco RV042 i have two Internet access connection from my ISP one with 30Mbps and the other with 8Mbps.
i have 30Mbps in WAN1 and 8Mbps on WA2
my issue that i was connecting both of the WAN connections using DHCP mode and it was working fine and the ISP modem was terminating the PPPOE
now i decided to use PPPOE on the Cisco RV042 and change the ISP modem to bridge mode.
WAN1 is working were as WAN2 is not working.
i tried to factory reset, shift links, in all cases WAN2 if its on PPPOE does not go up.
i am using latest firmware from cisco.com.
View 4 Replies
ADVERTISEMENT
Oct 23, 2011
I have 2 WAN connection @ my office. One is the static IP from Reliance Network
The other connection of WAN is dynamic from AIR TEL...
When i logged into my router. I can see the dynamic IP from Reliance on WAN1 status. But on WAN2 is see everything as 0.0.0.0. The WAN2 configuration has been set to get the IP automatically...
I tried the other solution offered by one of the support guys, by turning on and off the modem, but that does not work...
Or do i need to change the WAN2 connection to be PPoE or something...
View 4 Replies
View Related
Jun 17, 2012
I have a RV042 and want to establish one WAN connection via PPPoE. I enter Username and Password, Keep Alive, MTU=Auto. The router does not get an IP address (0.0.0.0) and the log says: "[pppoe] sending PADI", "last message repeated 5 times". What is confusing me is that a PC connected to the RV042 (and a DSL-Router operating in Modem-Mode "PPPoE Pass-Through") can establish a PPPoE connection with the same Username and Password. Why can the PC connect via PPPoE, but the RV042 can not?
View 4 Replies
View Related
Jan 27, 2011
I bought a Cisco Linksys RV042 (Firmware Version: 1.3.12.19-tm) a month ago. I installed it with two Cable Modems (Webstar DPC2100R2) from the same internet provider and with the same individual bandwidths for the two of those. My setup is Dual Wan mode since I only bought this device for load balancing the traffic through the two WAN connections. I need to clone both WAN MAC addresses on the router ports in order to get connected to my ISPs provisioning server. The RV042 has no issues getting a connection on WAN1 when MAC cloning has been made on this port, however, when I clone (user define, different from WAN1) MAC address for WAN2, this port never gets a connection and stays on IP 0.0.0.0 all the time.
I’ve tried factory reset, reloading the latest firmware (which already came pre-installed), switch modems from WAN1 to WAN2 and vice versa, disabling Firewall, turning on and off the ports on Port Management tab, changing SmartLink to Load Balance mode, enabling and disabling Network Service Detection, DHCP vs. Static IP on WAN ports, manual setup, setup through the wizard.
Nothing seems to make WAN2 port function correctly with the User Defined MAC address. The only way to make it work is using the factory (default) MAC address on WAN2, then it gets the IP address from the modem. Again, WAN1 works correctly with a user defined MAC address same as with Default MAC address enabled.I have read endless customer’s posts having the same issue from several years ago in this Community Forum and all over the web, and none of them have had a definite solution to the problem from the manufacturer.
View 1 Replies
View Related
Nov 21, 2012
Continued from [URL] which appears to have been closed by a moderator with a reference to Cisco small business website, but the registration there doesn't work, all buttons are inactive etc.
I just need to know what to do with this RV042. I have two modems, a cable and an ADSL. Both are configure correctly, in bridge mode. Both work fine when connected to WAN1, but when connected to WAN2 they never go online (dont' get IP address). The connect lights are on but they never go online.
Firmware Version: 1.3.13.02-tm
View 1 Replies
View Related
Feb 28, 2012
I was able to install the RV042 router to my ATT DSL line (WAN1 port-INTERNET) and it gets an external IP address automatically and the Internet works. When I connect my Comcast Internet to WAN2 port INTERNTE/DMZ) it doesn't get an IP address. and the Internet goes down and the WAN2 port ip address says 0.0.0.0.I've tried releasing/ renewing and it still says 0.0.0.0.Everything else is set as the default.
View 1 Replies
View Related
Dec 12, 2011
I have a RV082 with two internet connections, the main one is 4Mb symetric and the backup is 3mb/512Kb ADSL, I´ve tried both options: Smart line backup and Load Balance but I have the same problem in any case, at random and without apparent cause is lost internet connection, I tried also disabling WAN2 and got the same result
View 0 Replies
View Related
Jan 17, 2013
I want to use WAN2 in DMZ mode on my RV082 router. I want to connect this to a router which will go to another network.
So it will look like this:
LAN1 192.168.188.0
|
|
|
[Code].....
UPDATE: This does not work. In case anyone else tries this, it is not possible with this model of router. The RV082 has to either be in gateway or router mode. In gateway mode, it is doing NAT, and the DMZ will not route correctly to the other LAN. In router mode, the DMZ does route correctly to the other LAN, but the internet will not work because NAT is turned off. We had to add a second RV082 to the configuration to get this working. It cannot be done with 1 RV082.
View 1 Replies
View Related
Oct 15, 2012
I have both WAN1 and WAN2 connected to an ISP but only WAN2 should be used for outgoing mails. How and where can I specify this in the configuration?
View 3 Replies
View Related
Jan 15, 2013
We have 2 offices in different countries both using the RV082 router. Currently both offices have an internet connection on WAN1 and that is working fine. We are adding a Point to Point circuit between the two offices, and my question is on the RV082 configuration on each side.
I was going to configure WAN2 in DMZ mode on each router, then connect the point to point circuit to the WAN2 port. On the China side, the DMZ IP will have to be a private address (192.168.177.1), while the DMZ port on the San Diego side will be a public IP. We need internal computers to be able to go to the internet normally through WAN1, but also go through WAN2 if they are trying to reach the other network. I will be adding routes on each RV082 for this.
Is there anything wrong with this configuration? Do I need to change the routers from Gateway to Router mode? Does it matter if the DMZ WAN2 port has a private IP address?
View 2 Replies
View Related
Oct 24, 2012
We have an RV082 (firmware 2.0.2.01-tm),with an ADSL connection over PPPoE. It connects fine, and I can ping anything, and I can also access websites with HTTPS, but when trying to access any website with HTTP, it doesn't work.There's no load balancing going on, and it's the same whether we have the Firewall turned on or off, and everything else is pretty much as default.
View 4 Replies
View Related
Sep 27, 2011
I have a netopia 3347W adsl modem/router that I have put in "ethernet bridge" mode. At that point the RV110W has to authenticate to ATT using PPPOE. I have verified the username/paswd for the PPPOE connection. The 110w will not complete the PPPOE connection. Looking at the logs it shows that it handshakes and authenticates with the PPPOE server. Then unexpectedly the log shows a termination with exit status 15. It then tries to renegotiate the PPPOE connection.
View 2 Replies
View Related
Nov 1, 2011
My network consists of the following:
Office-RV042 with static IP ->SBS2003 (10.10.10.5/ 255.255.255.0)
Remote: BEFSR41 with Dynamic -> XP sp3 VPN client (192.168.3.x/ 255.255.255.248)
Within the RV042 I have enabled the PPtP server and assigned a user. No port forwarding enabled. All VPN passthroughs and firewall is enabled. DHCP server is disabled.I can establish a connection to the rv042 and ping PCs including the sbs domain server on the office side but am unable to browse any folders. When I attempt to access a network folder located on the office server I am prompted for a username/ password. Upon entering my domain credentials I get an error stating: "the user name you typed is the same user name you logged in with. That user name has already been tried. A domain controller cannot be found to verify that user name"
View 2 Replies
View Related
Nov 19, 2012
I have an RV082 and a RV042. I have been able to successfully establish a gateway to gateway vpn connection between them both, but both Routers unable to ping each other and I can't remotely administer each router through the VPN connection.
View 1 Replies
View Related
Sep 4, 2011
At this moment I'm trying to connect 2 router rv042 and i received the following error message
(g2gips0) #23: ERROR: asynchronous network error report on eth1 for message to 190.199.164.144 port 500, complainant 190.199.164.144: Connection refused [errno 146, origin ICMP type 3 code 3 (not authenticated)]
in the other router i don't see any error . what would be the problem.
View 5 Replies
View Related
Nov 15, 2010
So here is my issue. I have two sites, each with a Linksys RV042 on thier site.
Site 1:
External: 142.142.142.142
Internal: 192.168.25.0/24
Site 2:
External: 143.143.143.143
Internal: 192.168.26.0/24
We have setup a site-to-site VPN between these sites, and all traffic is running back and forth without isse.
At Site 1 we have configured the Client VPN for use with the QuickVPN software. Again, for site 1, this is not an issue. We are able to access all internal resources at Site 1 without issue (expect for some DNS related problems).
The problem that we have is attempting to access Site 2 resources via the QuickVPN connection at Site 1. Even though they are not suppose to exist, we are able to ping 192.168.26.1-6 (which are ghost addresses likely created by the RV042's) but no actual systems on at Site 2.
I have added the Client VPN connection at Site 2, but it has the same problem accessing resources at Site 1.
View 6 Replies
View Related
Jul 18, 2011
Im able to create a gateway tunnel with two rv042 routers in different locations ( i can see the tunnel connected in the router) but the quick vpn utility is not working , i also tried to use the pptp as server as an alternative( im able to connect using windows connection to the pptp server but whenever I browse any of the four ip's allowed for the pptp server \10.0.0.200-204 it takes me to the documents of the local computer....I attached the configuration for one of the routers it is the same as the other end , just the information is flipped.
Message was edited by: Adrian Torres
View 7 Replies
View Related
Feb 18, 2013
I am located in UK which uses PPoA for ADSL broadband. I use a DrayTek Vigor120 ADSL2 Modem to act as an ADSL bridge and PPoA to PPPoE converter. This passes the ADSL authentication requirement (and subsequent single static IP address) to the Cisco Small Business RV180W sitting behind the Draytek. However, the RV180 (Firmware Version 1.0.0.30) cannot form the PPPoE connection. I have tested the modem, adsl username and password by creating a PPPoE interface on my computer and connecting this directly to the Draytek modem. The computer receives the expected IP address and I can ping remote public IPs. I have entered the username and password into the PPPoE profile,
Authentication type: CHAP (confirmed by ISP but I have also tried all other options just in case).
Connection Type: Keep Connected.
MTU Size: 1400 (also tried default, which worked OK on computer interface).
MAC Address Source: Use Default (I have successfully used combined modem/router so a "fixed" MAC address is not required).
View 3 Replies
View Related
Mar 17, 2013
The RV180W would not connect to an AT&T DSL connection using PPPoE (modem in bridge mode), or behind the DSL Modem/router with the DSL modem/router providing a dynamic IP to the RV180W or a cable modem (TimeWarner Roadrunner dynamic IP). I upgraded the firmware yesterday and now the RV180W will connect to a dynamic WAN IP, but it still will not connect using PPPoE.
I have also noticed the admin interface is only accessible about 75% of the time. When going to 192.168.1.1 the login prompts either don't come up or if they do, after logging in, the screen never fully loads after that. I have to reboot the router to get it to work.
Also, the router has not yet pulled DNS from either the DSL or the cable modem. I had to manually enter those addresses.
View 1 Replies
View Related
Oct 15, 2012
My RV180 does not route properly between LAN and WAN through my PPPoE account. I am able to ping public IPs directly from the RV180 (through the diagnose section) but can not do it from any PC on LAN. The exact same configuration works perfectly well with a Linksys WTR610N. I upgraded formware from 1.0.0.30 to 1.0.1.9 but that did not make any difference.
The only time the RV180 will route is right after I reset to factory defaults and re-enter PPPoE account name and password. If I then reset my modem or the RV180, the RV180 does not route anymore between WAN and LAN even after several minutes and even though I can ping public IPs from the RV180.
View 18 Replies
View Related
Apr 17, 2013
I am connecting the RV180 to a Huawei Echolife HG850a ONT via PPPoE, dynamic IP address from ISP.
However, error message shows:
Fri Apr 19 02:54:15 2013(UTC) [rv180][System][NONE] pppoeMultipleEnableDisable: pppoe enable failed
Fri Apr 19 02:55:16 2013(UTC) [rv180][System][NONE] pppoeMultipleEnableDisable: pppoe enable failed
I am not able to get the RV180 to logon via PPPoE and get its dynamic IP.
Firmware is version 1.0.2.6, tried resetting to factory defaults, still the same.
View 6 Replies
View Related
Oct 25, 2012
Some days ago I bought a new RV180W router with firmware 1.0.1.9. The router is configured with PPPoE and I need to forward some port (a basic operation for a router!!!). I try in every way but it doesn't work. My old router works well. [URL]
View 1 Replies
View Related
Oct 15, 2011
I am looking at replacing my existing Netgear Wireless router, and I am thinkg of using a RV120W.My ISP requires PPPoE (uname/pword) and my wife's company requires we have a static IP on our side for VPN connections.Does the RV120W meet these requirements? In what I have found online, I see that the unit does static IPs and PPPoE, but cant find anything that confirms it will do both at the same time.
View 7 Replies
View Related
Dec 27, 2012
I bought a new RV180W router with firmware 1.0.1.9.The router is configured with PPPoE and I need to forward some port (a basic operation for a router!!!). I try in every way but it doesn't work. My old router works well.
View 1 Replies
View Related
Aug 19, 2011
I want to share the PPPOE internet connection between my Desktop and Laptop. The desktop has WIN7 and laptop has Win Vista. the desktop is having 2 LAN Cards.
View 1 Replies
View Related
Feb 28, 2013
One of my customers has a new f9k1110 and we need to configure PPPoE on it to get him logged in.
How do we access the router configuration?
View 1 Replies
View Related
Jan 24, 2013
I have RV042 and E4200 routers . I tried the manual UPnP port forwarding using Rv042 router and was succesful ( by typing 192.168.1.1 in the explorer and logged in using user name and password )
I am using a linux embedded system whose Internal IP ,Internal port are mapped .This system is connected to one of the LAN ports
I want to try auto UPnP port forwarding both for RV042 router and Linksys E4200 routers
After enabling the Upnp option only and logging out ,Can i add a port mapping entry in this router without logging in using a C++ program which runs on linux embedded system .
View 2 Replies
View Related
Aug 22, 2012
I was looking for a small business router that has VPN support and dual WAN support for load balancing. Upon reading reviews, I think RV042/RV042G is a good choice. Now am thinking if it supports intervlan/ router-on-a-stick configuration?
View 5 Replies
View Related
Mar 27, 2012
I'm trying to configure an 887VA for a pppoe ADSL2+ connection with no luck.I know the ISP requires pppoe (LLC), and the pvc is 8/35.
The CD light is on, and the line is up, but the 887 just won't connect
View 3 Replies
View Related
Jul 4, 2012
PPPoE connection isn't established...Config Cisco 1811 (c181x-advipservicesk9-mz.124-15.T15.bin):
...
vpdn enable
...
vpdn-group 1
request-dialin
protocol pppoe
[code].....
View 7 Replies
View Related
Jan 10, 2011
I have cisco router ASR 1006 .... i need to create PPPOE connection via Ethernet ... and can do that on the management port ???? and what is the type of adapter that use in the Giga Ethernt interface to connect it to fiber ???? hint :- my interface hardware SPA-10X1GE-V2
View 7 Replies
View Related
Jan 9, 2011
When it comes to configuring my new Linksys Cisco WRT120N router to my PPPoE connection. I've visited 192.168.1.1 but I'm not sure what to do next. So, I've got a PPPoE connection, static IP address, Linksys Cisco WRT120N router and a terrible ISP.
How to configure my new router so that I can start using the wireless for Internet access at home.
View 3 Replies
View Related
Mar 27, 2011
I have an ADSL connection and have configured the PPPoE subinterface on WAN1 (ADSL) this connection has a static IP, and I know that the ISP gives that to me through DHCP however I have 4 or 5 additional IP addresses also provided to me on that same link, and they are not given to me via DHCP.
How do I configure this router to have multiple fixed IP addresses on a PPPoE interface?
I also need to port forward some ports for each of the IP's but I assume this will be easy after i have the IP addresses setup.
View 4 Replies
View Related
