Cisco Routers :: Netopia 3347W - RV110W / 110w Will Not Complete PPPOE Connection
Sep 27, 2011
I have a netopia 3347W adsl modem/router that I have put in "ethernet bridge" mode. At that point the RV110W has to authenticate to ATT using PPPOE. I have verified the username/paswd for the PPPOE connection. The 110w will not complete the PPPOE connection. Looking at the logs it shows that it handshakes and authenticates with the PPPOE server. Then unexpectedly the log shows a termination with exit status 15. It then tries to renegotiate the PPPOE connection.
View 2 Replies
ADVERTISEMENT
Jan 10, 2013
We have RV220W at corporate office...intent is to have (5) groups of (3) users each connecting via VPN. Had assumed would be using QuickVPN and have set up users, etc and connections at current locations are quick, smooth, reliable. I have set up (2) locations (6 users so far). However, after 4th connection (no matter where or in what order) client hangs at "Verifying Network" and doesn't complete connection. So, I have unique usernames, etc but each of the (3) at a location are hitting the router with the same IP. Is this the problem? I'm sure the RV220W can handle 15 simultaneous connections, but can the router deal with (3) connections from the same external IP?
View 3 Replies
View Related
Nov 23, 2011
RV110W connected to ISP via PPPoE. MTU is default setting - 1492. IPSs tarif - 100 Mbit/sec IN, 40 Mbit/sec-OUT.When the laptop is connected to RV110w via ethernet the data transfer rate is 45 Mbit IN / 25 Mbit OUT.When a laptop is connected to ISP directly without a router a data transfer rate is 95 IN / 35 OUT.
View 0 Replies
View Related
Jan 8, 2013
Here is the configuration : I newly installed for a client a RV110W (firmware 1.2.0.9) wich connect on the internet trough Dlink 320B (ppoe connexion, in France - the provider is orange). Wifi is ok, VPN is ok, wan is ok ...
But no way to make port forwarding works (form wan to lan of course). I tried to reboot the router, the modem, reseting router configuration before re-apply mine, it didn't made any change. I also tried single and range port forwarding, without any succes...
View 2 Replies
View Related
Jul 4, 2012
I have an issue with Cisco RV042 i have two Internet access connection from my ISP one with 30Mbps and the other with 8Mbps.
i have 30Mbps in WAN1 and 8Mbps on WA2
my issue that i was connecting both of the WAN connections using DHCP mode and it was working fine and the ISP modem was terminating the PPPOE
now i decided to use PPPOE on the Cisco RV042 and change the ISP modem to bridge mode.
WAN1 is working were as WAN2 is not working.
i tried to factory reset, shift links, in all cases WAN2 if its on PPPOE does not go up.
i am using latest firmware from cisco.com.
View 4 Replies
View Related
Oct 24, 2012
We have an RV082 (firmware 2.0.2.01-tm),with an ADSL connection over PPPoE. It connects fine, and I can ping anything, and I can also access websites with HTTPS, but when trying to access any website with HTTP, it doesn't work.There's no load balancing going on, and it's the same whether we have the Firewall turned on or off, and everything else is pretty much as default.
View 4 Replies
View Related
Mar 16, 2011
I installed the quickVPN Client for use with RVS4000 small business router/VPN on a platform with Windows 7. It was not able to complete the VPN connection. I installed on Windows XP machine, both on the same network. The XP machine was able to connect just fine.
View 1 Replies
View Related
Jan 14, 2012
I bought a router Cisco WRVS4400N Wireless-N Gigabit Security Router - VPN v2.0 with the intention of using with the QuickVPN Clien for connecting to my home network.My home network is connected to a pre provide by my ISP Thomson and is connected to it but all my main network is controlled by the WRVS4400N, I have forward all the doors, as you can see by the log part below, and by analysing the log you can see that I can get any PING to complete the VPN connection. [code]
View 1 Replies
View Related
Oct 13, 2012
Signed onto pc as admin, logged into router with correct user name and password. No page in the browser based configuration displays the complete information for the page. Menus are missing as are option labels, etc. The last time I accessed the router (about a year ago) I didn't have this problem.
View 3 Replies
View Related
Jun 13, 2012
let me know whether you can make the attached network using by RV110W or not.When I read the mannual of "rv110w_admin.pdf", P38, I guess RV110W cannot be built both NAT & Router mode.Because, I cannot setup NAT for internet access if I setup "Operating Mode" as "Router" on the setting of "Networking > Routing".And, I cannot setup the routing for internet access & MPLS-VPN access if I setup "Operating Mode" as "Gateway" on the setting of "Networking > Routing".
View 2 Replies
View Related
Feb 13, 2012
Is it possible to set up an RV110W to limit access to only specified websites according to a schedule? I can block access to specific sites using the Internet Access Policy settings under Firewall, but I can't figure out a successful way to block access to all sites except those specified. I also tried establishing access rules but that did not work either.
View 4 Replies
View Related
Feb 16, 2012
After nothing but hassles with my Linksys WAG120N, I bought a Cisco RV110W. Yesterday, I tried setting it up with the Linksys being used only as a modem. I was unable to though because when I entered 192.168.1.1 into my browser as per the Cisco setup instructions, I was taken to the admin login for the Linksys. This seemed odd to me, because the Linksys was not connected to the PC at all. The connection setup was exactly as specified in the RV110W instructions: modem connected to dsl line, ethernet cable from modem (Linksys WAG120N) to the slot marked "WAN" on the RV110W, another ethernet cable from RV110W to my PC. Despite this, the admin page was for the linksys not the cisco.
Today, I exchanged the WAG120N for a Netgear DM111P, just a modem, not a router. Same setup configuration: modem connected to dsl line, ethernet cable from modem (NetgearDM111P) to the slot marked "WAN" on the RV110W, another ethernet cable from RV110W to my PC. Same result - type in 192.168.1.1 and get taken to the admin page for "Netgear DM111P" .
View 6 Replies
View Related
Apr 7, 2013
I make a vpn site-to-site IPSEC tunnel between 2 RV110W the above ,you will find the configuration
Site1
Site 2
always the same message
View 3 Replies
View Related
Feb 5, 2012
I'm having problems setting up VLANs on my RV110W Small Business Router. I have updated the firmware to the latest : 1.1.0.9 Here is my set up :
WAN settings :
IP : 192.168.1.252 / 255.255.255.0 - Gateway 192.168.1.254
VLAN1 (default) :
IP : 192.168.2.254 / 255.255.255.0
VLAN3 (test) :
IP : 192.168.16.254 / 255.255.255.0
Inter-VLAN routing option is checked.
Symptoms :
- The communication from VLAN1 to WAN is fine
- The communication from VLAN3 to VLAN1 is fine
- The communication from VLAN1 to VLAN3 is not working
My routing table is :Routing table Entry ListDestination LAN IPSubnet MaskGatewayInterface192.168.2.0255.255.255.0192.168.2.254LAN192.168.1.0255.255.255.0192.168.1.252WAN192.168.16.0255.255.255.00.0.0.0LAN0.0.0.00.0.0.0192.168.1.254WAN
As you can see, the gateway for VLAN3 is set to 0.0.0.0, which is wrong I believe. I don't know how to update that. I tried to add a a static route for the subnet, but the router did not let me do that.
View 1 Replies
View Related
Apr 17, 2013
I am trying to configure wake on lan for my desktop and I can't seem to get it. I have tried using single port forwarding under the firewall settings but it never works. The computer's BIOS has been configured to wake on lan and so have the Ethernet ports. I have an app for the iPad that i used to use ot send out a ping to my old router (E2500) setup that used to wake the computer just fine. But this new router (RV110w) does not work at all even with the same single port forwarding set up.
View 2 Replies
View Related
Mar 15, 2012
I've to setup RV110W router as a simple Wifi hotspot in a company network and this Wifi hotspot has to allow traffic to all internal LAN (very simple LAN with few workstation and one server) and also to Internet via our gateway. I know this product isn't really designed for that... but I've to do so. LAN is managed by Windows DHCP server and I've Internet acces through Firewall. I think I've to connect RV110W to the company LAN with the RV110W WAN interface. I want the Wifi IP address to be in the same IP range than the LAN to allow Wifi clients to access our internal server but RV110W doesn't accept this. Or do I've to ignore the WAN interface and deal with only the RV110W LAN interface?
View 1 Replies
View Related
Jan 26, 2012
I have a pptp server on my network and am trying to configure my new RV110W so that I can tunnel through to it from outside.
I believe I must do port forwarding for TCP on port 1723 to get those packets going to my PPTP server. PPTP also uses GRE and I don't see that as an option anyware in port forwarding... Does that just work... as a matter of the VPN pass through checkbox being enabled ?
My netgear router would lock up every few days but it under the firewall configuration it had list of services that included PPTP and I just selected that, entered the IP addresses on the outside that I would accept, and the IP address on the inside that the PPTP clients would connect to, and it worked....
I'm thinking it is harder on this device because this device supports actually logging into it.. I am interested in learning more about that technique especially if it is more secure but the way I see it the firewall device can see all of my network and the pptp server I am using is on a file server and limited to those files shared on that server.
View 3 Replies
View Related
Apr 2, 2012
With firmware 1.2.0.9 - can the RV110W be used as a VPN endpoint? The VPN capabilities have been expanded in this version - but from the docs this isn't quite clear to me.
View 3 Replies
View Related
Mar 31, 2012
I just bought and setup a RV110W. I noticed while scanning it from the WAN side that it always has port 443 open, even when remote management and VPN access are disabled. Why is this port still open, and how do I close it? Or is this a bug in the firmware? I am using firmware version 1.1.0.9, which is the most up-to-date for this unit. Having open ports allowing unsolicited contact from the WAN side, especially inadvertant ones, is a major security hole.
View 7 Replies
View Related
Dec 5, 2012
I have recently hit a brick wall with my router... Yesterday the router was acting funny rebooting about every 5 to 10 minutes. Didnt really think anything of it then it got annoying fast. So i checked my configs and nothing was out of normal checked my firmware and noticed it was out of date. So i grabbed the newest firmware 1.2.0.9 and uploaded it... uploaded fine and then rebooted as it should at that time the power flickered again because somone had plugged an large ac adapter over top of the power switch on the power bar and it was intermittently turning the power off when the table moved... the router then power cycled mid update and is now stuck at the blinking power light state and hasnt changed for 24 hours now...
View 1 Replies
View Related
Feb 3, 2013
I am thinking about buying one of the 2 routers i have listed above. I have some concerns though.
First off what are the MAJOR differences between the two? (they look the same to me)
Do they both contain PPTP and is it simple to configure? Do i need any kind of special client software? Can i use my iphone and ipad to connect to the vpn server. Is there a minium download/upload speed to have a vpn sever?
View 6 Replies
View Related
Jul 8, 2012
Regarding to the connection RV110W to any Cisco router, should I use a crossover cable accordingly? Because, I heard that the crossover function is done inside of some switches and routers. So, I would like to know whthether the function is included into RV110W.
View 3 Replies
View Related
Jun 4, 2012
Is there a way to configure the router through CLI (command line interface)In other Cisco devices we always were able to simply insert a configuration throught the CLI.Now it seems it can only be done with the Webbrowser.
View 7 Replies
View Related
Apr 24, 2012
I have an RV110W running firmware 1.1.0.9 that is working fine with VPN clients. However, one client cannot use VPN and I'm trying to set up some simple port-forwarding to allow RDP to a specific machine inside our network (IP address 10.143.193.2).
1) Where can I find explanations of what a warning means in the logs on an RV110W?
2) Why isn't traffic from my server making it back out from our network to the originating RDP client when it seems I have configured everything to allow this to work?
The details:
I have a firewall rule that says this. (Note, I've tried restricting the services to just RDP but expanded to all traffic as part of my testing.):
And a port forwarding rule that says:
But I keep getting these errors when testing the RDP from *anywhere* at all. Searching these forums and the internet at large for the reason these are warnings and what to do has been fruitless. However, these will show up for any attempt I make to connect. Also, there were rules for each of these IP addresses that show up as warnings to allow access to the 10.x.x.2 destination. It seems that the problem is traffic isn't making it back.
View 5 Replies
View Related
Mar 6, 2012
I bought a RV110W wireless router a couple months ago that I've been pretty happy with.
However, I have one significant problem with it. It is configured to send syslog messages to an internal server. Twice now it has gone into a mode where it starts dumping messages like,
ip_conntrack_is_ipc_allowed: ipc_entry_is_full
continuously, at a rate of about 20 per second. It otherwise seems to function normally, but of course if unnoticed my syslog file quickly grows to hundreds or thousands of megabytes. A reboot restores normal operation. It is running firmware 1.1.0.9. A search on the internet turned up no information about this problem.
It may be some corruption is occuring in the router's OS, or perhaps this is something that can be triggered externally (in which case it would be a weak form of DoS attack? Or maybe worse if in this state it is unable to properly apply the firewall rules.)
View 2 Replies
View Related
Jan 8, 2013
I'm trying to connect my home computer to a Cisco RV110W via host-to-network VPN. I'm on a mac using VPN Tracker 6. The Cisco router replaced sonic wall, and no one knew how to set it up, including me. VPN worked fine with sonic wall. I'm not sure configurations are correct in the router. I have:
WAN IP address (static IP address assigned by Verizon)
IP Address for PPTP server: 10.10.10.1
IP Address for PPTP Clients: 10.10.10.101/105 (actually we have a range of 101 to 120, but the PPTP configuration page won't allow me to manually input 120)
MPPE Encryption enabled
NetBIOS enabled
two PPTP users created with protocol PPTP
I'm not sure if my IP Address for PPTP Clients is correct, but he IP Address for PPTP Server matches the LAN IP address. This is correct, right? Because the router was set up by someone who was basically figuring it out, I'm not sure whether there are other configuration in the router that should be made to enable VPN connections. My VPN connection doesn't make it through phase 1 -- doesn't get to the point where it asks for a preshared key, so it's getting hung up very early in the process. I've made sure the IKE and VPN policy table configurations match what I have in the VPN Tracker 6 advanced configurations.
View 1 Replies
View Related
Oct 22, 2012
I have a RV110W which is am using as a router (not gateway), because it is connected to the DSL modem (not planning to bridge it) through its WAN port. The DSL modem forwards all PPTP traffic to the RV110W.The only pupose of the RV110W for me is to use it as a VPN router.
Info:
Firmware version: 1.1.0.9
Below are the settings I have:
WAN:
LAN:N.B. The modem runs a DHCP server, so I am relaying the requets to it
VPN:N.B. Also tried with 192.168.0.0 and 12.168.2.0 networks; same thing.
Routing Settings:
Routing Table:NB: 192.168.1.11 and 10 are VPN clients (created automatically).
Firewall:Users are being able to successfully connect to the VPN; however, there are couple of problems:
1. They are not assigned a gateway; hence, not internet connectivty (i want them to use the remote gateway)
2. They are not able to access the 192.168.0.0 network; hence unable to reach their DNS server and other hosts (run a tracert; they couldn't go beyond the RV110W VPN server IP). For this, i tried to turnoff the firewall on the RV110W, and also tried to create and Access Rule to allow all outboud and inbound traffic between LAN and WAN, but no success.
View 1 Replies
View Related
May 28, 2013
CE IP - 172.18.10.10 /30PE IP - 172.18.10.9/30 I had configured some floating static route on the PE towards CE .The routes were installed correctly till PE - CE link was UP as next hop IP was showing as connected .Now the link has been removed and I am receiving a supernet of 172.16.0.0/12 from PE2 via MPBGP. Although the 1st static route for 10.10.0.0 is showing in routing table, the other 2 ( 172.17.0.0 & 172.24.0.0 ) donot show. I believe that as both the routes and next hop fall under the supernet , the static route is not installing. But I don't know why is this behaviour. I tried to remove the distance 250 from both the routes , but still the static route does not install. I tried this on GNS3 but got the same results .
View 14 Replies
View Related
Apr 15, 2013
We have purchased an RV110W and I need to restrict internet access to the entire internet with the exception of 4 websites that are required for employees to do their jobs. I need to do this on 3 specific machines, not the entire network. I have looked at the internet access and schedule management pages of the router and just can seem to figure out how to do this.
View 8 Replies
View Related
Sep 4, 2012
I am trying to connect from the outside to a TCP server inside my lan that is listening on Port 25565. I am using a RV110W. I did the DMZ IP for it.
From the Lan I can establish a connection (even with my dynamic dns address). As I try it from the outside the server log tells me that a connection has been establishen but it shows the gateways IP. Afterwards it tells me the connection hase bin lost (Time out).
As I set Port forwarding I even cannot reach the server from the out side and lan.
I even did set up access rule WAN to Lan.
View 1 Replies
View Related
Jan 3, 2012
I have a small problem: I succeeded in etablishing a VPN connection to my RV110W from Internet. When I'm connected with my VPN connection and surf on the web, my public IP address is my home router's one. However, I can't join my home computers.My VPN adress is 10.0.0.10.Ping to 10.0.0.1 and 10.10.10.1 (RV110W adresses both) works, but I can't ping to 10.10.10.101 (home computer). I tried with all my firewalls inactive.Did I miss something on my RV110W configuration ?
View 6 Replies
View Related
Jun 2, 2013
I'm looking to update our office network and replace our old wireless box.I've been looking at the RV110w after a google search and need to find out some things before suggesting anything.
Currently our network is running a public IP address for each piece of equipment which we'd like to keep, mainly for ease. We have a wireless access point running in invisible mode for wireless client access to the entire network, and also a Netscreen firewall.
What I'd like to do is the following:
1. Keep public ip addresses for wired clients, complete with existing network/local server access/RDP.
2. Set up two VLans on private ip addresses - one to have full access as per the wired clients and the other only for guest Internet access.
Is this something the RV110w is able to do? If so how would I go about setting it up?
View 3 Replies
View Related
Mar 10, 2013
I have a problem with my RV110W router. I would like to setup Quick VPN access. Manual is quite straightforward: enable management, create users, install client and that's all, should be working. But NOT. it does not work.
Remote Management is enabled on port 8080. Should it be changed to 443 as required for QVPN? Or it does not matter. Is it ok, to have management on 8080 and QVPN on 443?
I have tried to connect via QVPN Client ver. 1.4.1.2. Of course ip as well as user and pass has been changed. I tried to change management port to 443, but first:
1. i was not able to access management console at all
2. QVPN - still did not work
View 4 Replies
View Related
