Signed onto pc as admin, logged into router with correct user name and password. No page in the browser based configuration displays the complete information for the page. Menus are missing as are option labels, etc. The last time I accessed the router (about a year ago) I didn't have this problem.
View 3 RepliesI cannot open the config page of beetel adsl2 router using 192.168.1.1I have connected my laptop to router via Lan cable. Now when I give the ipconfig, I get some random IP and does not get the default gateway: Autoconfiguration IPv4 Address. . : 169.254.129.188 Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . :I cannot ping 192.168.1.1 nor 169.254.129.1 thus the web page of router cannot be opened.This all happened after I reset my router.
View 3 Replies View RelatedI've recently been gifted with a WRT54GS v.2 which came from a family member who upgraded their wireless router and therefore passed this one along to me. It was working perfectly for them, but not me.
I've tried using the setup CD and doing a manual setup, but no internet connection is detected. I must confess to being a total wireless router newbie, this is my first one, so I am stumped as what to do next. I've looked at the FAQ's and through the forum as well, but I just don't know what might apply to my situation and as I am not very well versed in the terminology, I tend to get lost.
I have a Linksys WRT54GS router that is giving my some trouble. I recently got a new PC and moved my old one into my bedroom along with my Xbox 360. So I didn't have to switch my Ethernet cable between my xbox and pc I bought another cable. Much to my dismay this new cable would not work. At first I thought maybe the cable was bad, but when I connect my pc directly into my modem it works fine. This had my come to the conclusion that it was my router. I have two pcs hooked into it that work fine and a laptop that connects to it wirelessly, but if I try to hook my xbox or pc to it using the new cable they just act as if there isn't a cable connected. When I look at my router the light for the ethernet port that the new cable is in will flash on and off. I've hard reset my router and updated the firmware.
View 2 Replies View RelatedWhy does err 0x80040900 show up sometimes when tx/rx email? I use a WRT54GS linksys router. I have more than one computer which use Microsoft Outlook 2003 to check email accounts. When the error shows up I can ping the server no problem. The error sometimes goes away and comes back randomly.
View 2 Replies View RelatedI have a linksys wrt54gs wireless router (working fine since last 3 years) which connects to the internet fine if there is no password set. However if i set WEP password to protect the wireless connection, i am not able to connect to the wireless connection. Everytime i enter the passphrase, when trying to connect to the wireless network, it refuses to accept the password. I have tried this with 2 laptops (both running windows 7) and both have same issue.
View 2 Replies View RelatedMy lap top and other desktop are able to detect the internet but not my main computer with this router.
View 2 Replies View RelatedLinksys tried multiple WRT54g routers and access point, 192.168.1.1 can't open the router config page.
View 5 Replies View RelatedI got an old WISE WS-4016 16-port 10/100Mbps Fast Ethernet Switch from a friend of mine which was not in use. However i am unable to find any information regarding this switch anywhere online.Unfortunately we couldn't find any manual for this switch as well.
View 4 Replies View Relatedlast week i noticed a lot of connectivity issues while surfing the web through wifi. my setup: dell vostro 3550, wireless adapter n1030, win7 64-bit after several attempts of fixing the issue following recommendations wrt the n1030 adapter (eg deactivating bluetooth, changing channels of router to 1 or 11, etc), I decided to complete erase all driver and hardware entries of the blue-tooth wireless adapter (like suggested in this thread: [URL]
afterwards i installed ALL available and latest drivers from dell or/and intel regarding this wifi adapter. the result is that the wireless adapter is again shown in the hardware manager and also in the system information of win7 which is great.BUT, somehow the win7 wifi network software/tools does still not recognize the adapter by the means of unplugging the lan cable i just see the wifi symbol with a red x. also opening the network and sharing console does not show the adapter to me although when clicking on "configure wifi networks" and "adapter properties" it is there and active "ready to use". additionally, the intel wireless diagnosis tool tells me that the adapter must have been deactivated or deinstalled. well, the tool is partially right, but the adapter was reinstalled and shows up in the hardware manager. somehow it missed that point ?
I just got a new Sharp Aquos Television and I wanted to try to find the SSID so that I could pick up a connection with my TV. When I went to command prompt and typed ipconfig to get the default gateway, the gateway ip took me to what appears to be my modem's config page and not the Linksys. how I can get to my WRT54G config page.
View 2 Replies View RelatedSome emails that come into the INBOX are not complete and do not have graphics.On opening some emails in my Inbox, it tells me that THE WEB PAGE CANNOT BE FOUND.Some emails are going straight into the DELETED ITEMS BOX and are not SPAM. Some of them can be opened by clicking on to the LINK but others will not open.I have also had (Your email programme does not support HTML), which I do not understand.I telephoned my server and was advised to contact a PC Technician as I may have a VIRUS.
View 3 Replies View RelatedI need to set up a password for my wireless network, but every time I try to access the setup page, the router stops responding. I've gotten as far as it asking for username and password, where I enter admin as the password....and then nothing. The connection times out. I really need to protect my network.
View 1 Replies View RelatedI recently (~month ago) switched to a new computer after my old one (which I had configured the router on previously with no problems) died.Since then, I have been unable to access my router's config page (entering in the ip address simply results in a blank page with no prompt for username/password). Switching browsers (I've tried Firefox 5 and IE 8) does not solve the problem, nor does disabling AdBlockPlus/NoScript on Firefox. Any way to access my router so I can begin forwarding ports again?
View 1 Replies View RelatedI have successfully set up a pptp vpn from my new rv220w. I have also successfully logged in using 2 seperate laptops and also my iPhone. They all work great. There is one issue. When connected and I log into the router it does not show these laptops or iPhone as being connected to the vpn. There is two spots that its supposed to show the page refreshes and shows nothing connected. Is there a setting I am missing?
View 2 Replies View RelatedI'm having wrt610n and there is an issue, i can login to the config page via http, but using the same computer i'm not able to login there via https but the same time i can login via ipad and the other computer, using the https.i even tried to reset the router settings, but the result was the same, so what PC option can cause it?
View 6 Replies View RelatedHave problem with both of my wag120n routers. I setup remote access, from the intranet it works fine. But from internet instead of showing me the page it starts downloading it. Instead of home page trying to save ¨download¨, if i put a long link like xxx.com/setup.cgi?=etc then it tryes to save ¨setup.cgi¨. All fileas are empty, 7kbytes.
View 7 Replies View RelatedI just got a DIR-655 and set it all up pretty easily. I have 6 wired and 3 wireless. All work fine and all are set to use DHCP. But if I go (in the router) to the Lan Computers list under Device Info, three devices (2 wired, 1 wireless) do not appear. I do have a switch added to the system, but of the three devices connected to it, 1 shows in th Lan Computers list and the other 2 do not.Since everything works, I'm mostly just curious why this is. Every previous router I've had showed everything correctly.
View 3 Replies View RelatedThe rouge access points being detected by the 5508 WLC are not showing up on the Context Aware tab of NCS? I have a MSE 3310 installed and configured and it shows to be syncronizing with the WLC. I'm sure I am missing some part of the configuration just not sure where.
View 3 Replies View Relatedthe name of my wifi network changed and I do not know why, therefore the password for the former name will not work with the new network name
View 1 Replies View RelatedI am unable to connect to the internet thru my router, Lynksys WRT54Gs. The network worked fine before I went on vacation. I accessed the internet by connecting the ethernet directly to the modem, and have been unsuccessful at my attempts to reset the router with 192.168.1.1
View 1 Replies View RelatedI have an ASA 5550 running 8.4(5) and have installed ASDM 7.0(2), but when I try to manage the bookmarks under the Remote Access - Portal when I try to edit an individual item in a bookmark list the screen does not display any information. Is this a know bug, or do I need to have a specific java version for the new ASDM? As a side note, I have not noticed any other issues with the new version of ASDM, only the bookmarks. I initially tried to downgrade the ASDM version that I was using to connect, but it will no longer allow me to connect.
View 6 Replies View RelatedI have encountering a problem with a new installation at my clients side recently.We have a 5508 wlc and a bunch of Laps connected to it.Recently we associated a 1142ap to the same controller.The issue we are facing is that , the client laptops that are connected to THIS ap are showing maximum of only 54mbps in their network information dialogue box.Initially i couldn't understand why this could happen.But after a bit of research , i came to know that this could happen because of ``unticked`` data rates in the controller , or because of not using wpa2 with aes as the security standard for N-series access points.Now i have enabled all data rates in the High Throughput section as well as enabled the correct encryption standard.But still the issue persists.We have checked with multiple laptops , to rule out the possibility of a faulty n/w card
View 3 Replies View RelatedI did RECOVERY on my computer. Its a Compac Windows XP Home edition. This computer runs off of my main computer by a router & adapter. My router & adaptor are showing green but the Internet is showing red. Its becuz my high speed Internat service is ATT.my.yahoo.com. which comes through IE. On my newer computer all is fine. My IE works good & all is working. but my IE on my older one which runs with the router wont set up.
View 1 Replies View RelatedA friend was over with his lap top, since then I'm getting "sam's pc network",instead of my network, I can't seem to disable it, nor can the other devices in the house connect to it, the default is Sam's....
View 1 Replies View RelatedI got a static ip from my isp. I set up my static ip manually through my linksy router. I need the static ip to connect to a private network for my new job but cant connect to that network. I went to whatsmyip and found that my old dynamic ip is still showing up externally, it looks like my ip4 is using the dynamic as a preferred. My question is do i need to manually change the network connection on my LAN and wireless connection under ipv4 to change it from automatically obtain TO use the following address and put in my static? And do I have to change the DNS also? I am on a home network with one desktop on vista home premium and laptop windows 7.
View 5 Replies View Relatedi formatted my pc but after that lan is not showing in network connections
View 1 Replies View RelatedIn asus router model rt-n10, there is a client list when you bring up 192.168.1.1 showing names of devices also mac addresses and ip addresses. How do I add names to the list so I know which devices are using what ip etc. I have tried the advanced settings in the router to see if I can do it this way , but no luck.
View 1 Replies View RelatedI tried to log on to my wireless routers IP address but it only gives me a blank page after signing in. the IP address is 192.168.1.1. Is there a problem with this ip address?
View 1 Replies View RelatedI have ZTE ZXDSL831II modem. Here is the [URL]how can I block a website from modem configuration page?
View 5 Replies View RelatedMotorola wr850gp wireless router. The default ip is 192.168.10.1. I attempted to use it as a wireless access point and now it is not working at all. I tried connecting the router LAN port to the computer and 192.168.10.1 pulls up nothing.I tried connecting the modem to the WAN port and the LAN port of the router to the PC, but then I have no internet access at all. I tried resetting the router, still nothingAll lights on the router are green. I don't know what the heck is going on?
View 3 Replies View RelatedI've tried all IP's that could be... 192.168.1.1 ,etc. , etc.Of course I am behind a router but even though I tried the same with connecting directly, it showed my gateway to be 78.56.191.254 which didn't work at all ( but was ping-able ).I restarted router and computer several times as well as switched form router to direct connection which brought no luck as well.
View 9 Replies View RelatedThe other day while I was browsing the internet all of a sudden my internet stopped working. I look down below and try to connect to the network again but it no longer shows my network anymore. I went into the room of my router and it looked fine. All lights were lit up like they should be. I turned on my Laptop to see if it was just a problem with my desktop but it's still not showing my network either.
I have restarted my router and reset it numerous times and it has still yet to show my network. It only seems to work if I connect it to my Laptop with an Ethernet cord. I have two different routers (Both Linksys) and they both do not work.I also have two different wireless adapters (D-Link & Netgear) and they both do not work