Cisco Routers :: RV082 - Configure WAN2 In DMZ Mode On Each Router
Jan 15, 2013
We have 2 offices in different countries both using the RV082 router. Currently both offices have an internet connection on WAN1 and that is working fine. We are adding a Point to Point circuit between the two offices, and my question is on the RV082 configuration on each side.
I was going to configure WAN2 in DMZ mode on each router, then connect the point to point circuit to the WAN2 port. On the China side, the DMZ IP will have to be a private address (192.168.177.1), while the DMZ port on the San Diego side will be a public IP. We need internal computers to be able to go to the internet normally through WAN1, but also go through WAN2 if they are trying to reach the other network. I will be adding routes on each RV082 for this.
Is there anything wrong with this configuration? Do I need to change the routers from Gateway to Router mode? Does it matter if the DMZ WAN2 port has a private IP address?
View 2 Replies
ADVERTISEMENT
Dec 12, 2011
I have a RV082 with two internet connections, the main one is 4Mb symetric and the backup is 3mb/512Kb ADSL, I´ve tried both options: Smart line backup and Load Balance but I have the same problem in any case, at random and without apparent cause is lost internet connection, I tried also disabling WAN2 and got the same result
View 0 Replies
View Related
Jan 17, 2013
I want to use WAN2 in DMZ mode on my RV082 router. I want to connect this to a router which will go to another network.
So it will look like this:
LAN1 192.168.188.0
|
|
|
[Code].....
UPDATE: This does not work. In case anyone else tries this, it is not possible with this model of router. The RV082 has to either be in gateway or router mode. In gateway mode, it is doing NAT, and the DMZ will not route correctly to the other LAN. In router mode, the DMZ does route correctly to the other LAN, but the internet will not work because NAT is turned off. We had to add a second RV082 to the configuration to get this working. It cannot be done with 1 RV082.
View 1 Replies
View Related
Oct 9, 2012
I am trying to configure RV082 router with Mac Native VPN Client for my remote access. However, no matter what I did, I am not able to make it works. Can any one can give me an example of how to conguration my RV082 router and Mac Book Pro(Mountain Lion)?
View 2 Replies
View Related
Nov 17, 2011
isco epc3925 in transparent bridge provided by isp with following wan details
ip=x.x.x.120 subnet=255.255.255.248 gw=x.x.x.121 and 2 dns server ip's
I can't get the one-to-one nat working. read in some forums that the rv082 can do the job.
View 4 Replies
View Related
Mar 5, 2012
We have a RV082 configured with two ISP Wan connections. We recently implemented a VOIP phone system (SIP) (192.168.1.50) that is being used in appliance mode on our network. We currently have two WAN connections Load Balanced. My goal is to configure all my VOIP traffic to go out through the 1st ISP and the rest of the data through ISP #2. is this possible to achieve using the RV082? We are using a Skype SIP Trunk connection.
View 1 Replies
View Related
Oct 23, 2011
I have 2 WAN connection @ my office. One is the static IP from Reliance Network
The other connection of WAN is dynamic from AIR TEL...
When i logged into my router. I can see the dynamic IP from Reliance on WAN1 status. But on WAN2 is see everything as 0.0.0.0. The WAN2 configuration has been set to get the IP automatically...
I tried the other solution offered by one of the support guys, by turning on and off the modem, but that does not work...
Or do i need to change the WAN2 connection to be PPoE or something...
View 4 Replies
View Related
Jul 4, 2012
I have an issue with Cisco RV042 i have two Internet access connection from my ISP one with 30Mbps and the other with 8Mbps.
i have 30Mbps in WAN1 and 8Mbps on WA2
my issue that i was connecting both of the WAN connections using DHCP mode and it was working fine and the ISP modem was terminating the PPPOE
now i decided to use PPPOE on the Cisco RV042 and change the ISP modem to bridge mode.
WAN1 is working were as WAN2 is not working.
i tried to factory reset, shift links, in all cases WAN2 if its on PPPOE does not go up.
i am using latest firmware from cisco.com.
View 4 Replies
View Related
Oct 15, 2012
I have both WAN1 and WAN2 connected to an ISP but only WAN2 should be used for outgoing mails. How and where can I specify this in the configuration?
View 3 Replies
View Related
Jul 2, 2007
I have some problem connecting to sites when I'm using the router in Load Balancing mode on the 2 WAN. Looks that when a connection to a site is started with a WAN is not manteined with this one but jump from a wan to the other, causing, in some site like Home Banking to be disconnected every time. I would like to know if it's possible to configure the roouter in Load Balancing but Bindind the source and the destination IP address so the same wan will be used for the entire time this connection is up. In opther words the Load Balancing has a sense beetween connections not beetween the same connection.
View 9 Replies
View Related
Jan 1, 2013
We have a RV120W Wireless-N VPN Firewall and we want to configure the router in brigde mode (transparent). Because we have another Firewall, use for filtering and default gateway on the LAN. The ISP provide IP address by DHCP, so we must connect the internet connexion to the WAN interface. But How can we do for connected the RV120W to our firewall? The router mode on the RV120w allows-it to make this configuration?
View 1 Replies
View Related
Feb 21, 2013
I have a RV082 VPN Router. But my internet connection is ADSL brodband. How can i connect and setup a VPN connection to other RV082.
View 1 Replies
View Related
Jan 27, 2011
I bought a Cisco Linksys RV042 (Firmware Version: 1.3.12.19-tm) a month ago. I installed it with two Cable Modems (Webstar DPC2100R2) from the same internet provider and with the same individual bandwidths for the two of those. My setup is Dual Wan mode since I only bought this device for load balancing the traffic through the two WAN connections. I need to clone both WAN MAC addresses on the router ports in order to get connected to my ISPs provisioning server. The RV042 has no issues getting a connection on WAN1 when MAC cloning has been made on this port, however, when I clone (user define, different from WAN1) MAC address for WAN2, this port never gets a connection and stays on IP 0.0.0.0 all the time.
I’ve tried factory reset, reloading the latest firmware (which already came pre-installed), switch modems from WAN1 to WAN2 and vice versa, disabling Firewall, turning on and off the ports on Port Management tab, changing SmartLink to Load Balance mode, enabling and disabling Network Service Detection, DHCP vs. Static IP on WAN ports, manual setup, setup through the wizard.
Nothing seems to make WAN2 port function correctly with the User Defined MAC address. The only way to make it work is using the factory (default) MAC address on WAN2, then it gets the IP address from the modem. Again, WAN1 works correctly with a user defined MAC address same as with Default MAC address enabled.I have read endless customer’s posts having the same issue from several years ago in this Community Forum and all over the web, and none of them have had a definite solution to the problem from the manufacturer.
View 1 Replies
View Related
Dec 18, 2012
I saw older discussions over WOL and RV082/RV042. As router blocks broadcast packets from internet to lan, to make WOL work, i should change router's ARP table using telnet, probably with V1 and V2 versions this action was possible, but trying telnet connection (http://<Router IP Address>/ sysinfo123.htm?ConsoleSimulation=1 with RV082 V3 nothing appears, and telnet connection on standard port (23) fails.
How to make pass WOL magic packets through a RV082 V3 from internet to LAN ? Using simply port forwarding don't work, as router discard broadcast packets incoming from internet.
View 4 Replies
View Related
Feb 29, 2012
We have a RV082 Router and we are trying to do port translation.
For example:
88.123.2.5:80>192.168.1.10:2334
88.123.2.5:81>192.168.1.10:2335
However this does not seem to be possible as I can only choose the source port and the destination IP address unlike the RVS4000.
View 1 Replies
View Related
Aug 9, 2011
My rv082 router protect link gateway is already activated. How do i change the key or activate it with a new activation key?The router dont have any link to change the key. I'm using v1-2 rv082
View 4 Replies
View Related
Nov 21, 2012
Continued from [URL] which appears to have been closed by a moderator with a reference to Cisco small business website, but the registration there doesn't work, all buttons are inactive etc.
I just need to know what to do with this RV042. I have two modems, a cable and an ADSL. Both are configure correctly, in bridge mode. Both work fine when connected to WAN1, but when connected to WAN2 they never go online (dont' get IP address). The connect lights are on but they never go online.
Firmware Version: 1.3.13.02-tm
View 1 Replies
View Related
Feb 28, 2012
I was able to install the RV042 router to my ATT DSL line (WAN1 port-INTERNET) and it gets an external IP address automatically and the Internet works. When I connect my Comcast Internet to WAN2 port INTERNTE/DMZ) it doesn't get an IP address. and the Internet goes down and the WAN2 port ip address says 0.0.0.0.I've tried releasing/ renewing and it still says 0.0.0.0.Everything else is set as the default.
View 1 Replies
View Related
Sep 7, 2012
config to setup PPPoE on the cisco 831 router to be used with a modem in bridge mode. I have tired other peoples configs found on the web but, not all the commands were available on the IOS version thats on the router. Also note that I bought this as a used router and I dont have a service contract so I am unable to download an updated IOS. The router ver is 12.3(7)T9 and the IOS is c831-k9o3sy6-mz.123-7.T9.bin. Running config below is last tried still could not connect or get ip address from isp. [code]
View 2 Replies
View Related
Jan 25, 2012
My client has a DSL modem and a Belkin wired 4-port router configured to connect to it using PPPoE. Apparently there is no way to configure the E2500 such that it may be dropped in as a direct replacement for the Belkin (which would also provide wireless access) without the PPPoE login/password (from the DSL provider, Verizon).
I would like to connect the "Internet" port of the E2500 to one of the Belkin's 4 ports, in order to use the E2500 for wireless internet access without using any of the 4 wired ports but I think this creates a NAT within an existing NAT network?
To avoid that if I configure the E2500 in wired bridge mode, it becomes transparent, and I can no longer access its administration interface using the address 192.168.1.1 (since that address belongs to the Belkin). How may I, for example, change the wireless password which the E2500 is in wired bridge mode?
View 1 Replies
View Related
Mar 9, 2011
I want to configure my router to use 2 ADSL lines each with a dialer and a modem in RFC2684 mode. I have a 2821 (IOS 12.4) with an HWIC-4ESW.
My network topology is like this :
ADSL Modem 1 (RFC2684) --
(Fa0/0/0)
Router -- (Gi0/1) MyLAN
(Fa0/0/1)
ADSL Modem 2 (RFC2684) --/
1. I configure my DSL Modem in RFC 2684. The first use 172.16.0.2/29 and the second 172.16.0.3/29. I connect this devices to Fa0/0/0 and Fa0/0/1.
2. I configure Vlan1 to use the network configured on my modem :
interface Vlan1
ip address 172.16.0.1 255.255.255.248
3. I try to ping my devices :
#ping 172.16.0.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.0.3, timeout is 2 seconds:
!!!!!
[code]....
View 3 Replies
View Related
Aug 7, 2012
We're getting the following message in the logs when we ry to connect: encrypted Informational Exchange message is invalid because it is for incomplete ISAKMP SA
One of the router is a V2 and the other is a V4 if that makes any difference.
View 12 Replies
View Related
Feb 20, 2013
Is there documentation on setting the RV042G to Router Mode and what that changes to it's topography? The manual simply tells us to click the button to change the mode?!?!? A 4th grader could figure that out - but what does it do to the unit? Does it basically become a glorified switch with an internet connection? Can the 2nd WAN port be used as a switch node?
View 7 Replies
View Related
May 9, 2013
wether the Cisco RV180 router model can be configured with a public IP address on the LAN interface? I'm planning to use it in the following setup:
Internet ------------- WAN port (public IP) RV180 LAN port(public IP)-------------- WAN(public IP) RV016 LAN (private IP)
Disabling gateway operational mode and switching to router should disable NAT and allow this setup but need to confirm if it works? I'm concerned if the web management interface actually allows a public IP to be set on the LAN side.
View 1 Replies
View Related
Jan 29, 2013
We have an RV082 setup with WAN to the internet and LAN IP of 192.168.188.1.If I add a static route like so:
network: 192.168.166.0
mask: 255.255.255.0
gateway: 192.168.188.2
hop count: 1
interface: LAN
The device with IP 192.168.188.2 will be connected directly to one of the LAN ports on the router.Will that work to route, trying to get to 192.168.166.0 to the IP of 192.168.188.2?It just seems odd because the packets would hit the router then go back out through the LAN port.
View 4 Replies
View Related
May 9, 2013
I have a Meraki Firewall that sits behind my Cisco RV082. The Meraki is setup to run a VPN connection with my server but I am having problems passing the VPN traffic through properly.
I have 2 Uverse Internet Connections that the RV082 using load balancing so that they are shared. I have 10 static IP's.
I am trying to come in on one of my static IP addresses throught the Cisco RV082 to the Meraki and after doing a capture on the meraki it appears that it is starting to receive data to intiate the VPN connection but when it sends data back to the VPN client machine it never makes it.
View 1 Replies
View Related
Nov 12, 2012
I have reset my RV082 router (both wit the reset switch and the factory default wizard) and run the setup wizard but regardless I can't connect to shaw.ca which is my service provider. I notice that if I use http://192.168.1.1 the browsers (IE & FF) default to https://192.168.1.1 and then I am prompted for a certificate. I can enter if I ignore the request but after getting in I simply cannot connect to my ISP.
View 4 Replies
View Related
Jan 12, 2012
Is it possbile to NAT to other subnets with the RV082. It is on a 192.168.41.x and I have a phone system on a 192.168.20.x. After searching all over others are saying no.
View 4 Replies
View Related
Jan 14, 2013
I just set up a new Linksys/Cisco RV082 router with the intent to get VPN working from outside the building. I have gone through the setup and while everything looks good, I have not been able to connect yet. I have tried everything that I know how, and am now hoping to get the answer from some pros.
Here's my setup. We use Comcast Business class internet. The modem is plugged into WAN port 1 on the RV082. I'm using the router as a DHCP server, that is working fine. My local subnet is 192.168.0.0/220
Right now all I want is to be able to log in as a client using QuickVPN. I set up one user and a client to VPN tunnel using the router's config page. Here's the settings I have:
Tunnel Interface is setup on WAN1, checkbox is enabled.
Local Group Setup
Local Security Gatewaytpe: IP Only
Local Security Group Type: Subnet
[Code]....
It seems like something is blocking the connection, but seeing that I have tried this after disabling the firewall completely it doesn't make sense to me. I also went into the config page for the modem and set up the router as a DMZ. I have also tried connecting with the client built into Windows 7, but that doesn't work either, I just get "connection failed with error 619"
I have the port in QuickVPN set to auto, but have tried both 443 and 60443 with same results.
I ran a port scan at [URL] and it shows I have 3 ports open...80,443, and 1723
View 4 Replies
View Related
Jan 24, 2012
I have a VPN tunnel from one RV082 to another, first router has IP range of 192.168.1.0 and the second one has range of 18.18.18.0, the connection works fine, here is where the issue starts, I am at a PC in the 18.18.18.0 network and I ping an IP in the other one e.g. 192.168.1.50 and it pings fine, but when I try to RDP into it or do anything to it I get no response, is it a firewall issue? Is it a NAT issue? I am at a loss, now that IP i mentioned does have RDP enabled and working because it is being port fowarded in the 192.168.1.0 router and I can access it through the public IP.
Also a workstation with a static IP 192.168.1.18 I can ping it if im in the local network but if I am in the remote one I cannot at all.
View 7 Replies
View Related
Jul 28, 2010
we have an RV082 router that a few days ago started restarting itself after normal usage.The simpton is that when people come to office, starting using the Internet the RV082 resets. It stays online for 3 to 12 minutes and then it resets again.
clicking on Reset to Factory Default in the web interfaceafter the reset, I confirmed that it was reset to factory default I reset it again using the reset buttomre-configure the RV082 manually.I also tested with another identical rv082 (hw version and firmware version) and after doing a backup of the config of the original rv082 and restoring it in the new rv082, the same problem happends.
View 20 Replies
View Related
Feb 21, 2013
Is there documentation on setting the RV042G to Router Mode and what that changes to it's topography? The manual simply tells us to click the button to change the mode?!?!? A 4th grader could figure that out - but what does it do to the unit? Does it basically become a glorified switch with an internet connection? Can the 2nd WAN port be used as a switch node?
View 1 Replies
View Related
Nov 24, 2011
WRV200 does not transmit packets in Router mode. This issue has been describes already here:
[url]....
So is there a solution to forcing this router function properly according to manufacturer's declaration (router mode)?
View 1 Replies
View Related