Cisco Routers :: RV042 / How To Configure Some DHCP Option
Jun 19, 2012
I have a RV042 VPN Router with the latest firmware v4.2.1.02.This Router is connected to the main site by a VPN Tunnel.
Now, I like to configure some DHCP Option so I can put a IP Phone behind the RV042. The IP Phone should receive a IP by DHCP from the RV042 and of course, the IP of the Call Manager with the Option 150.
I can configure DHCP and it works fine but I can't find where I have or can configure Option 150.
View 3 Replies
ADVERTISEMENT
Oct 13, 2012
I need DHCP Option 66 to be enabled my small business RV042 router, so the IP phones could know where is the TFTP server.
View 1 Replies
View Related
May 3, 2012
Is it possible to configure DHCP option 150 on the RV220? I have a Cisco 7940 IP phone that is trying to connect back to my office. The VPN is up and I can ping the relevant server but I can't see any way to configure the DHCP option.
View 5 Replies
View Related
Apr 3, 2012
Have a client wanting to hand out public ip addresses to all clients from a PFSense Firewall terminating the internet connection.
How do I allow the Cisco Switches currently in place, configured with private ip addresses in the 10.10.x.x ranges and Vlans, where the main 3550 layer 3 has defined dhcp scopes for each vlan, to relay dhcp requests from all vlans to the PFSense firewall?
I assume I would take off the currently defined dhcp scopes for the vlans and configure each vlan/switch with the ip helper address and specify the PFSense firewall and that Nat would have to be disabled onthe firewall?
View 1 Replies
View Related
Nov 13, 2012
I Cannot setup the DHCP on the router, the page has no content.
View 1 Replies
View Related
Jul 11, 2012
I have a few sites using the RV042 with wireless access points and some of them have over 50 devices.In reviewing the documentation (specifically,[URL]), I came across this:Enable DHCP server: Check the box to allow the router to dynamically assign IP addresses to up to 50 connected devices. Uncheck the box if you have another DHCP server on the network or you want to configure static IP addresses for your network devices.Is this accurate? Or will the RV042 allow more than 50 devices?
View 3 Replies
View Related
Dec 8, 2011
I tried to configure two RV042 working together. [code] WAN2 of both Router1 and Router2 are unused (unplugged). However, the Host2 can never ping to Host1. So as to Host1. Should I need to configure the protocol binding for all the traffic to the WAN1?
View 3 Replies
View Related
Oct 3, 2012
I have a RV042 router. The problem that I am having with it is that the DHCP is giving out the wrong Default Gateway and DNS Server. There is no option to change the DHCP server IP on any of the settings pages on the router. I am begining to think that there might not be a way to do it. I see that there is an option for the DNS under the DHCP page but the Public IP that is being handed out is not the one on that page. I also have 2 WAN connections hooked up as well a DSL link and a Cable link (the cable link is the primary one).
The following information is provided in an effort to resolve this issue:
IP of Router 10.0.0.2
IP of DHCP Server (the one that is being handed out):10.0.0.1
IP of DNS (the one that is being handed out): 10.0.0.11
What I want to it be.
IP of Router: 10.0.0.2
IP of DHCP 10.0.0.2
IP of DNS 10.0.0.2
View 3 Replies
View Related
Aug 19, 2011
I need configuring Cisco RV042 dual wlan and port forwarding for 2 servers web and dns in LAN
View 1 Replies
View Related
Feb 7, 2011
I've purchased a Linksys RV042 hoping I could connect my two ISP.Both of them are 1/1 Mb, first is DSL second PPPoE connection.The problem is that on system summary page it doesn't show me that second WAN is connected. Even when I trying to manually connect to Internet it doesn't work.
When this connection is in Load balance Mode, internet is very slow, sometimes it's even disconnected.
My question is:How to configure Load Balance properly?I've tried this page:
[URL]...
View 13 Replies
View Related
Sep 14, 2011
I have tried replacing a loaner RV082 V2 with an RV042 V3 router with firmware 4.0.4.02. All worked well, including the site to site VPN. However, in spite of the fact that I have ports 443 and 4125 forwarded to the server (192.168.2.10), we are unable to connect via RWW. There is no such problem with the RV082. What is different with the way we configure these V3 routers for port forwarding?
View 2 Replies
View Related
Apr 22, 2013
Cisco RV042 Dual WAN VPN Router -how to configure dynamic DNS without having to use the pre-programmed DDNS companies that are populated by default if my DDNS company is not listed and you cannot manually enter another company that is not on the list?
View 1 Replies
View Related
Sep 12, 2012
I know how to disable the DHCP on the SRP527W but i was wondering how do i configure DHCP relay to point to a network DHCP server.
View 1 Replies
View Related
Feb 14, 2012
I am trying to configure two 3845 routers to act as dhcp server and dhcp relay. Clients are connected to the router that relays all dhcp requests to the vrf instance which is used to connect it to the router wich is running dhcp server.
Router1
ip vrf dhcp_dns
rd 8:1
int gi0/0
ip vrf forwarding dhcp_dns
ip address 192.168.200.5 255.255.255.248
[code]...
So far I can see dhcp requests coming from the R1 and dhcp server on R2 replies with the dhcp offer but PC is not getting any ip.
View 8 Replies
View Related
Oct 3, 2011
I'm trying to configure my Cisco Router 2811 which is also acting as the DHCP server for my branch office for DHCP option 60 and 43 so Aruba AP's at my branch can discover it's master Controller? What is the command I need to enter in the Cisco router?
View 1 Replies
View Related
May 5, 2013
I have sample lab dhcp-client ------- (vlan62) sg-300 switch (vlan62) ------ dhcp server
When I set on switch :
dhcp relay : enable
option 82 : enable
dhcp server address: ip of dhcp
When debug packets from client to server, there is no 82 option in dhcp discover packets. I mirror all traffic to mirror port with wireshark. I can see dhcp packets but without option 82.
Firmware version: 1.0.0.27
View 2 Replies
View Related
Dec 29, 2012
Is there a way to set up a Site-to-site VPN between RV042 & Cisco 2911? I "googled" this and obtained a document, but it is not regarding Cisco 2911: [URL]
Routers are needed to setup it successfully. I have tried on both routers several configuration steps, no success...
View 3 Replies
View Related
Dec 12, 2012
I have a very simple setup containing 3 C2960S switches:switch 1: central switch, acting as router between VLAN 1 en VLAN 2switch 2+3: edge switches, connected via 1 link to central switch, both on VLAN 2,Clients connect to switch 2 and 3 using dhcp, switch 1 uses dhcp relay to forward requests from VLAN 2 to the dhcp server on VLAN 1. So far so good.Now I want switch 1 to add option 82 to the dhcp requests so the dhcp server can see whether the request came through switch 2 or switch 3. I tried turning on dhcp option 82 support on switch 1 by doing.
View 2 Replies
View Related
Oct 27, 2011
In RFC 951, the format of BOOTP packet was legislated, but the vendor information was not legislated in this document, so the authors of this document had described that :"If the 'vend' field is used, it is recommended that a 4 byte 'magic number' be the first item within 'vend'. This lets a server determine what kind of information it is seeing in this field. "
I think it meant that the format of vendor information wasn't fixed in RFC 951, and any vendor can legislate a new format of vendor information by itself. And the value in "magic cookie" can be set by any vendor.But in RFC 2131, the format of DHCP packet was legislated, and the "magic cooke" was fixed to values 99, 130, 83 and 99, I think it meant that the format of option information in DHCP packet was fixed absolutely and any vendor can't legislate a new format by itself.
Since the format of option information in DHCP packet was fixed absolutely, why the network device needs "magic cookie" to identify the mode in which the succeeding data is to be interpreted ? I think the magic cookie is not useful in DHCP packet because the format of option information is fixed. In other words, there is only one format of option information forever.
View 6 Replies
View Related
Jul 2, 2012
While configuring a 5500 wireless controller, i came across this option of DHCP proxy under Advanced tab of Controller Option.It asks for the dhcp option 82 remote id format & the dhcp timeout.
1. What is the significance of this & when do we use it?
2. Also, under each wlan ssid that we create, there is an option of dhcp address required under the advanced tab. Do we need to use this option, if we are defining a normal dhcp pool in our controller for that ssid.
View 3 Replies
View Related
May 7, 2012
I am using a WLC 5508 and its internal DHCP server. I cant find anywhere I can setup option 43. However, the access points are connected in just fine. Do I need to worry about setting up a seperate DHCP server to get option 43 setup properly?
View 7 Replies
View Related
Mar 14, 2013
I have Cisco 1131 & 1300 Light Weight Acces Points and I have 5508 WLAN controller. If i enable the wlan controller internal DHCP Server can this access points will work with this internal DHCP server or do i need to configure DHCP option 43 for these access points? Can these access points works with LWAPP or do i need to configure CAPWAP?
View 4 Replies
View Related
Jan 25, 2013
I own a Nanostation5 Loco, and I have a router behind it.I would like to add a DHCP Lease to that router and do a port forward to the router.I can not find the DHCP Lease option in Nanostation settings, but if I choose to see DHCP Leases in "Extra info" on main page I can see some MAC and IP addresses there.When it comes to port forwarding, I fill the form slots with info, and when I press OK to save it a pop-up comes saying "Please fill out this field", a field for another forward rule.
View 3 Replies
View Related
Oct 21, 2012
How to configure ASA not to drop packets with ip option 7 (record route)? According to the docs, ip inspect ip option will drop all ip option packets except 0,1,and 20 (EOOL, NOP, or RTRALT):
"If an IP header contains additional options other than EOOL, NOP, or RTRALT, regardless of whether the ASA is configured to allow these options, the ASA will drop the packet. "
Also, policy-map type inspect ip-options treats only these 3.
View 1 Replies
View Related
May 12, 2012
I convert IOS Cisco AP 1130 LAP to 1130 Autonomous mode. Well, the periphericals - clients connect to SSID AP no recieved I.P Adress, I think that is not possible active option DHCP server in AP 1130 dispositive. In mode I.P static clients the connection is established successfully.
View 1 Replies
View Related
Jul 4, 2012
Does the two listed POE switch ports on the 880 series routers are active out of the box (default) or is configuration or extra parts required as internet pictures appear to show what looks like a power connector new to the POE ports?
View 8 Replies
View Related
Apr 17, 2013
I upgraded the firmware to latest and apparently i've lost couple of options inlcuding TCP Dump in diagnostic as well as I cannot find how to disable/enable an ethernet port.
View 5 Replies
View Related
Dec 29, 2011
I just purchase the Cisco Router RVS4000 vpn and I am having problem configuring the VPN option. I just try all way I could imaging, but somehow something are missing and I don't know what it is. Here are a image of my current configuration.
No matter the change on my configuration, the status always in down.
View 1 Replies
View Related
Jan 13, 2013
Recently I bought RV220W router and found out that PPPoE connection option or profile do no have service name field at all. Unfortunately, my ISP requires this to be able to connect. I had done some research before buying this router by going through online device manager demos on cisco website. RV220's interface is not available, but RV215 is and I checked out some of the common features between both routers. Surprisingly RV215's PPPoE connection settings has service name option.
I suppose, unless there is new firmware update (my current router is already running the latest available firmware), this option cannot be added in the interface. What I want to know is, is there any way to configure the router to use the service name in PPPoE option or in PPPoE profiles? I don't think RV220W can be accessed via terminal/SSH or maybe even terminal.
View 8 Replies
View Related
Mar 16, 2011
We have a Network set up with a RV042 router. Router is hooked up to Cox Cable and ATT DSL. Currently have 20 computers hooked up to the router all using Static IP addresses. Setup has been in place for over 7 years. I want to set up a Wireless Access point on this network. The problem is, I can't seem to get DHCP to work right even WITHOUT the Wireless Access Point. I have taken one of the computers that works great with a static IP and changed it to be DHCP, I have enabled DHCP on the router and set the from and thru parameters for the IP assignment. The computer will connect and get an IP address and it allows me to see all the INTERNAL servers on the network but going to the Internet is REAL FLAKY. I usually have to refresh 5 or 6 times to get a web page and sometimes even that don't work. If I do get a page to come up there is about a 10% chance that it will bring up a subpage of that page without doing a refresh 5 or 6 times. Its like it won't hold the connection to the Internet. I did notice one thing different in the User Manual of the RV042 that is different than all the other Linksys routers I have worked with. It says that when you enable the DHCP on the router, you then make sure ALL computers hooked to it are set for DHCP. All other routers I have worked with do NOT use that word ALL. Am I missing some setting or is this a binding thing where you are either ALL static or ALL DHCP?
View 1 Replies
View Related
Dec 20, 2011
How can I configure VPN connection between Cisco RV042 and Fritz!box 7170?I can establish VPN channel with Linksys RV042 with firmware 1.3.12.6-tm. When I set the same setting to Cisco RV042 (firmware v4.0.2.08-tm) VPN channel is not established.
View 1 Replies
View Related
Sep 13, 2012
configure ip-sec vpn tunnel between ASA5525x and RV042
View 5 Replies
View Related
Jan 26, 2011
I Echolife 520b, can not enable wireless network in the menu Basic Wireless LAN option is missing
View 1 Replies
View Related
