Cisco Routers :: RV042 DHCP Screen Is Blank
Nov 13, 2012I Cannot setup the DHCP on the router, the page has no content.
View 1 Replies
ADVERTISEMENT
Cisco Routers :: RV042 Web Utility Screen Goes Blank After Login?
Feb 1, 2012I'm running a new RV042 with the latest firmware (4.1.1.01). I set it up about 2 weeks ago and have been running it without an issue. Today I tried to go in to the web utility to make some changes. I was prompted for the userid/password, which it appeared to accept (if I typed in the wrong ones it rejected it), and then the screen went blank (normally I would get the status screen now.) Instead the screen I get is the light blue of the log-in screen, but there is nothing on it. The router has switched to the page https://192.168.1.1/home.htm I have tried different browsers and accessing it from different computers - the situation is always the same. I have power cycled the router, and there is no change. I suspect the next step is a manual reset to factory defaults - but of course I would rather not (as I didn't save all my settings of course!)
View 2 Replies View RelatedCisco Routers :: Blank Screen When Logging Into RV082?
Dec 4, 2011When I log into my router I can see the navigation tree on the left, but the rest of the screen is blank. I was at one time able to see the info on my Windows 7 computer and not my Vista, but now all my computers are blank.
View 3 Replies View RelatedHow To Extend Windows Screen From Going Blank
Aug 24, 2012my screen goes blank if not used after about 10 mins how do i extend time?
View 1 Replies View RelatedNew Hard Drive Showing Blank Screen
Jul 11, 2012i changed the hd in a nm-cue and configured the router accordingly and i opened a session to it but the screen is blank.
[code]...
Can't Access Router Settings - Blank Screen?
Jul 29, 2012I am trying to change the name of my wireless network but when I go to the 192.168.1.1 and type in my password, it just goes to a blank screen. I've accessed my router a lot of times before this way. It is a lisksys router.
View 1 Replies View RelatedCisco Switching/Routing :: 3750 - Blank Screen On SSH Connection
Feb 20, 2012If i try to ssh to a 3750 switch on our 4th floor, it ask's me for a username and password.
After entering the password, it doesnt connect. It shows a blank screen with a flashing cursor.
If i connect to the switch directly via console port, i can see port uplink and downlinks but still cant do anything more.
Wireless :: Have Older Laptop Vista No Picture Blank Screen?
Jul 7, 2011have older laptop vista no picture blank screen new laptop window 7 can i hook them together
View 1 Replies View RelatedCisco Routers :: RV042 / Login Screen On WAN Address With Remote Management Disabled
Aug 28, 2011My first try at configuring my RV042 has had unexpected results. I set a WAN and LAN address, but did not enable remote managment and did not configure any port forwarding. I expected to be able to connect to the router on the LAN and I could. The surprise came when I put in my web address. I got a router login page. How do I suppress than on the WAN side. I have a static address with my ISP.
View 1 Replies View RelatedCisco Routers :: RV042 - How To Setup DHCP Option 66
Oct 13, 2012I need DHCP Option 66 to be enabled my small business RV042 router, so the IP phones could know where is the TFTP server.
View 1 Replies View RelatedCisco Routers :: RV042 / How To Configure Some DHCP Option
Jun 19, 2012I have a RV042 VPN Router with the latest firmware v4.2.1.02.This Router is connected to the main site by a VPN Tunnel.
Now, I like to configure some DHCP Option so I can put a IP Phone behind the RV042. The IP Phone should receive a IP by DHCP from the RV042 and of course, the IP of the Call Manager with the Option 150.
I can configure DHCP and it works fine but I can't find where I have or can configure Option 150.
Cisco Routers :: RV042 Maximum Number Of DHCP Clients?
Jul 11, 2012I have a few sites using the RV042 with wireless access points and some of them have over 50 devices.In reviewing the documentation (specifically,[URL]), I came across this:Enable DHCP server: Check the box to allow the router to dynamically assign IP addresses to up to 50 connected devices. Uncheck the box if you have another DHCP server on the network or you want to configure static IP addresses for your network devices.Is this accurate? Or will the RV042 allow more than 50 devices?
View 3 Replies View RelatedCisco Routers :: RV042 - DHCP Giving Out Wrong Default Gateway And DNS Server
Oct 3, 2012I have a RV042 router. The problem that I am having with it is that the DHCP is giving out the wrong Default Gateway and DNS Server. There is no option to change the DHCP server IP on any of the settings pages on the router. I am begining to think that there might not be a way to do it. I see that there is an option for the DNS under the DHCP page but the Public IP that is being handed out is not the one on that page. I also have 2 WAN connections hooked up as well a DSL link and a Cable link (the cable link is the primary one).
The following information is provided in an effort to resolve this issue:
IP of Router 10.0.0.2
IP of DHCP Server (the one that is being handed out):10.0.0.1
IP of DNS (the one that is being handed out): 10.0.0.11
What I want to it be.
IP of Router: 10.0.0.2
IP of DHCP 10.0.0.2
IP of DNS 10.0.0.2
Routers / Switches :: Unable To Access IP - Getting Blank Page After Signing In?
Mar 4, 2011I tried to log on to my wireless routers IP address but it only gives me a blank page after signing in. the IP address is 192.168.1.1. Is there a problem with this ip address?
View 1 Replies View RelatedCan't Access Routers Login Screen
Feb 21, 2013i just bought a netgear router. i was able get into routers login screen once. thought every thing is good? everything looked correct? now i cant get into login screen at all again. im confused it should be easy. either use 192.168.1.1 or 192.168.1.2 or 192.168.0.1 and 192.168.1.254. i tried them all with no luck.
View 3 Replies View RelatedLinksys Wired Router :: DHCP Setup On RV042?
Mar 16, 2011We have a Network set up with a RV042 router. Router is hooked up to Cox Cable and ATT DSL. Currently have 20 computers hooked up to the router all using Static IP addresses. Setup has been in place for over 7 years. I want to set up a Wireless Access point on this network. The problem is, I can't seem to get DHCP to work right even WITHOUT the Wireless Access Point. I have taken one of the computers that works great with a static IP and changed it to be DHCP, I have enabled DHCP on the router and set the from and thru parameters for the IP assignment. The computer will connect and get an IP address and it allows me to see all the INTERNAL servers on the network but going to the Internet is REAL FLAKY. I usually have to refresh 5 or 6 times to get a web page and sometimes even that don't work. If I do get a page to come up there is about a 10% chance that it will bring up a subpage of that page without doing a refresh 5 or 6 times. Its like it won't hold the connection to the Internet. I did notice one thing different in the User Manual of the RV042 that is different than all the other Linksys routers I have worked with. It says that when you enable the DHCP on the router, you then make sure ALL computers hooked to it are set for DHCP. All other routers I have worked with do NOT use that word ALL. Am I missing some setting or is this a binding thing where you are either ALL static or ALL DHCP?
View 1 Replies View RelatedCisco Routers :: Auto / Programmatic UPnP Port Forwarding For RV042 And E4200 Routers
Jan 24, 2013I have RV042 and E4200 routers . I tried the manual UPnP port forwarding using Rv042 router and was succesful ( by typing 192.168.1.1 in the explorer and logged in using user name and password )
I am using a linux embedded system whose Internal IP ,Internal port are mapped .This system is connected to one of the LAN ports
I want to try auto UPnP port forwarding both for RV042 router and Linksys E4200 routers
After enabling the Upnp option only and logging out ,Can i add a port mapping entry in this router without logging in using a C++ program which runs on linux embedded system .
Cisco Routers :: RV042 / RV042G / Small Business Routers With Inter-VLAN Capability
Aug 22, 2012I was looking for a small business router that has VPN support and dual WAN support for load balancing. Upon reading reviews, I think RV042/RV042G is a good choice. Now am thinking if it supports intervlan/ router-on-a-stick configuration?
View 5 Replies View RelatedLinksys Wired Router :: RV042 Control Light Blinking But Never Receives Dhcp Settings
Feb 15, 2010I have a problem with RV042. My ISP gives me automaticly IP address and i had no problems using different types of routers, including linksys routers. With RV042 i just can't get the IP. It says, the port is up, i see the packets/traffic, front control light is blinking but it never receives the dhcp settings, doesn't matter if i use wan1, wan2, dual wan mode or single wan. I have the newest firmare 1.3.12.19tm. System statistics says "disconnected" but the packets come in and go out. Log shows absolutely nothing. I also disabled firewall but it didn't work. I can't seem to find the older 1.3.12.6 firmware.
View 7 Replies View RelatedCisco Routers :: RV042 Won't Get Second IP
Feb 27, 2012I have two Internet connections-
1-DSL Modem (WAN1-Internet Port)
2-Cable Modem-Comcast (WAN2-DMZ/Internet Port)
I connected the DSL (WAN1-Internet) port in and the Cisco RV042 was able to get an IP automatically. I tested the connection and it works just fine. Then I connect the Cable Modem-Comcast (WAN2-DMZ/Internet Port) in and I have the RV042 automatically optain IP address. But it just says 0.0.0.0. I've tried release/renew and that does nothing. Also, when I connect the 2nd Internet connection the Internet goes down. The only way it goes back up is when I disable under the PORT MANAGMENT setting.
All the settings have been kept to the default.How can I get the router to obtain an IP address from the Cable Modem-Comcast (WAN2 DMZ/Internet Port).
Cisco Routers :: NAT Over VPN On RV042
Mar 6, 2012We have an Cisco RV042. We need to setup a VPN with a business partner who is already using our current IP scheme on another VPN with another client. They have asked us to NAT our IP's from 192.168.25.x to 192.168.245.x
I can't seem to figure this out on this router. I have done it on a Sonicwall and Watchguard, but can't seem to get it to work on the RV042.
I have setup the VPN and the One-To-One NAT. The tunnel will connect (using the 245.x IP as our local IP on the VPN setup), but no traffic will pass through.
Cisco Routers :: Rv042 Configuration With Vpn?
May 20, 2012i was planed to make a vpn over rv042 so i get the rv042 connected behind a thosmon 456(configured as a bridge) and 1 static ip ... and i configured the vpn and worked great ...but due to some circumstance i get a package of 6 ips insted of the old ip , so when i try to configure the router with the ISP they but the wan ip 10.232.x.x and told me that an internal ip from there lan ... and give me the 6 ip of 196.x.x.x to use as 1 for internal interface for the rv042 and 5 for the pc's,now the vpn not working anymore...notice: when try to configure the vpn tunnle in the local securty setting i mark the ip only and the ip that abear is the wan ip 10.232.x.x but i can't ping that ip beside i can ping the internal ip of the router 196.x.x.50does rv042 can support static and virtual ip inside the lan |! can i configure the thomson as pppoe and use one static ip from 196.x.x.x as wan ip for it ... and use anther 196.x.x.x ip for the rv042 to get access from outside and connect the lan to the rv042 with internal ip 192.168.x.x ...so i can access the vpn from outside .....and can connect the device i need to use static ip to the thomson ...
View 0 Replies View RelatedCisco Routers :: RV042 - Bug Found In VPN?
Sep 23, 2011Firmware v4.0.4.02 has a nasty bug in the VPN section. If you switch to "IP by DNS Resolved" (yes, it says "Resolved" instead of "Resolution". Gotta love all the Engrish in the RV042!), it will automatically populate the field with "@yourdomain.com". This will cause the VPN to not lookup the proper IP address. Simply deleting the atmark after it populates will fix the problem.
Let's see what happens when we validate a Cisco RV042 webpage:
Errors found while checking this document as HTML 4.01 Transitional!
Result: 353 Errors, 1 warning(s)
Don't even get me started on the horrible Javascript...
Cisco Routers :: RV042 To ASA VPN Not Coming Up?
Apr 24, 2013i am trying to make a simple Site to SiteVPN between two offices, one has Cisco ASA and one has RV042 router.when traffic initiated from ASA side, i keep getting this message in Debug and tunnel wont come up
.
[IKEv1]: Group = A.A.A.139, IP = A.A.A.139, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.Apr 26 00:15:53 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
whereas if traffic initiated from RV042 side, i keep getting this message in debug and tunnel wont come up.
Apr 26 00:43:44 [IKEv1 DEBUG]: IP = RV.RV.RV.139, Oakley proposal is acceptableApr 26 00:43:44 [IKEv1 DEBUG]: IP = RV.RV.RV.139, IKE SA Proposal # 1, Transform # 0 acceptable Matches global IKE entry # 6Apr 26 00:43:44 [IKEv1]: IP = RV.RV.RV.139, Connection landed on tunnel_group RV.RV.RV.139Apr 26 00:43:45 [IKEv1]: IP = RV.RV.RV.139, Connection landed on tunnel_group RV.RV.RV.139Apr 26 00:43:45 [IKEv1]: Group = RV.RV.RV.139, IP = RV.RV.RV.139, Freeing previously allocated memory for authorization-dn-attributesApr 26 00:43:45 [IKEv1]: Group = RV.RV.RV.139, IP = RV.RV.RV.139, PHASE 1 COMPLETEDApr 26 00:43:45 [IKEv1]: IP =RV.RV.RV.139, Keep-alive type for this connection: DPDApr 26 00:43:45 [IKEv1 DEBUG]: Group =
[code].....
Cisco Routers :: Enabling 6rd On RV042?
Sep 27, 2012Apparently one of my two ISPs,CenturyLink, supports 6rd connections to IPv6.
This is supported natively on my Q1000 ActionTec modem, however my modem is in "transparent bridging" mode, so that the RV042 v3 can be the only router.
how to configure the RV042 to operate in this manner.
Per the CenturyLink FAQ: the IPv6 address space is:
2602::0 /24
Most importantly, can I do this WITHOUT buying a new modem.
Cisco Routers :: Unable To Log Into RV042
Aug 28, 2011I have a RV042 router (Ser#: NKS10462300, HW V3) running Firmware version v4.0.2.08-tm (Jan 14 2011 22:08:38) set up as a gateway. Right after it boots I am able to long into its web interface but shortly after that if I try to log into it I go through a very log time out while the web page is waiting the router to respond and then eventually IE comes back and says it 'cannot display the web [age'.
View 30 Replies View RelatedCisco Routers :: Can't Connect With RV042 VPN
Jan 14, 2013I have a Cisco RV042 VPN Router and I have added a group vpn, but when I am trying to connect I got an error that the remote vpn server isn't responding.
Here's my log:
2013/01/15 12:24:53 [STATUS]OS Version: Windows 7
2013/01/15 12:24:53 [STATUS]Windows Firewall Domain Profile Settings: ON
2013/01/15 12:24:53 [STATUS]Windows Firewall Private Profile Settings: OFF
2013/01/15 12:24:53 [STATUS]Windows Firewall Private Profile Settings: OFF
2013/01/15 12:24:53 [STATUS]One network interface detected with IP address MY HOME IP
[code]....
If I am trying to connect the status of the vpn user in the remote interface is "online".I have deactived my firewall at home and at the server for testing purposes.
Cisco Routers :: Configuration Of RV042 VPN
Apr 19, 2012I am looking to configure RV042 for VPN access to local machines and Win 2008 server. The story: Had issues with remote printers being created for clients logging into old Linksys RV042 with Linksys VPN software. First Tech exposed server without security, and it had to be removed as it was being attacked, but did not fix printing issue. 2nd tech could not get VPN to work after 1st tech. 3rd tech, 4hours, and I got that the router is a piece of ... So I'm out over 1000, and not able to have a simple router set up. The present situation. New RV042 with firmware V4.1.1.01, using Cisco VPN client 5.0.07.0410, most XP 32 bit machines coming into network, one 64 bit win 7. My clients have been unable to access their data for too long.
View 3 Replies View RelatedCisco Routers :: Setting Up VPN On RV042?
Feb 6, 2012Is there any documentation out there on a step-by-step instructions on setting up a vpn on a RV042 router?
View 1 Replies View RelatedCisco Routers :: Set Up 2 Subnet With Two RV042?
Apr 30, 2012I'm trying to set up 2 subnet with two RV042 routers. One router will act as a gateway and both WAN ports will be used by two different isp connection. The first router (gateway) LAN IP will be 192.168.0.1/24. I would also like to set up another router behind the gateway with with separate subnet 192.168.1.X/24. And I would like clients on the 192.168.1.x subnet to use the internet through the gateway router and clients on the 192.168.0.x subnet to access resources on the 192.168.1.x subnet. Am I able to do this with two RV042?
View 6 Replies View RelatedCisco Routers :: RV042 V3 / Out Of Memory
Sep 2, 2012The issue is when I am using PPTP the router seems to die, not every time but I would say about once a week now. I am the only PPTP user, simply using RDP. A few hours into an RDP session the PPTP connection drops and cannot be re-established, or quickvpn, nothing. Routing still works (somewhat, high latency) locally.
When I've checked the logs both times I see:
TimeEvent-TypeMessageSep 3 17:07:56 2012KernelOut of memory: Killed process 14354 (pppd). Sep 3 17:07:56 2012KernelOut of Memory: Kill process 14354 (pppd) score 177 and children. Sep 3 17:07:56 2012KernelOut of memory: Killed process 14367 (sh). Sep 3 17:07:56 2012KernelOut of Memory: Kill process 14354 (pppd) score 234 and children. Sep 3 16:46:41 2012KernelOut of memory: Killed process 14330 (pppd). Sep 3 16:46:41 2012KernelOut of Memory: Kill process 14329 (pptpctrl) score 134 and children. Sep 3 16:46:41 2012KernelOut of memory: Killed process 14324 (pppd). Sep 3 16:46:41 2012KernelOut of Memory: Kill process 14324 (pppd) score 177 and children. Sep 3 16:46:40 2012KernelOut of memory: Killed process 14328 (sh). Sep 3 16:46:40 2012KernelOut of Memory: Kill process 14324 (pppd) score 234 and children. Sep 3 15:36:15 2012KernelOut of memory: Killed process 14187 (pppd). Sep 3
[code]....
Cisco Routers :: RV042 Drops VPN?
Nov 11, 2012I have an RV042 connected via VPN to the office (to a LinkSys DFL-700). Sometimes the VPN is dropped and never activates again. In this state, if I try to connect to the WEB interface, I can log in, but the router hangs at the login screen. I have to power recycle the router to make it work again.
Updated to latest firmware 4.2.1.02 for V3 hardware. The funny thing is that services from the WEB routed through to local IP adresses on the lan is still accessible. I have setup PPPT VPN on the router, and that also fails to work.
Is there, as a workaround, any possibility to access the routers reset page or access via TELNET to reset the router? This migth be useful, when I'm out. (I have a backup solution to access the local network at home).
Cisco Routers :: RV042 And AT&T DSL Configuration
Jun 29, 2012I have just purchased the RV042 and while it is working great on WAN1 over Xfinity/Comcast broadband, I'm unable to get it working with my AT&T DSL for WAN2. I am planning on running this in failover mode - not load balancing.
The DSL modem it is connected to is a SpeedStream (hooking up laptop directly works etc. etc.). The SpeedStream is set to PPOE authentication passed in via the computer (in this case the RV042). On the RV042 side, I set it to use PPOE, using the credentials as given my AT&T DSL. The DNS servers are set to the ones recommended