When I log into my router I can see the navigation tree on the left, but the rest of the screen is blank. I was at one time able to see the info on my Windows 7 computer and not my Vista, but now all my computers are blank.
View 3 RepliesI Cannot setup the DHCP on the router, the page has no content.
View 1 Replies View RelatedI'm running a new RV042 with the latest firmware (4.1.1.01). I set it up about 2 weeks ago and have been running it without an issue. Today I tried to go in to the web utility to make some changes. I was prompted for the userid/password, which it appeared to accept (if I typed in the wrong ones it rejected it), and then the screen went blank (normally I would get the status screen now.) Instead the screen I get is the light blue of the log-in screen, but there is nothing on it. The router has switched to the page https://192.168.1.1/home.htm I have tried different browsers and accessing it from different computers - the situation is always the same. I have power cycled the router, and there is no change. I suspect the next step is a manual reset to factory defaults - but of course I would rather not (as I didn't save all my settings of course!)
View 2 Replies View Relatedmy screen goes blank if not used after about 10 mins how do i extend time?
View 1 Replies View Relatedi changed the hd in a nm-cue and configured the router accordingly and i opened a session to it but the screen is blank.
[code]...
I am trying to change the name of my wireless network but when I go to the 192.168.1.1 and type in my password, it just goes to a blank screen. I've accessed my router a lot of times before this way. It is a lisksys router.
View 1 Replies View RelatedIf i try to ssh to a 3750 switch on our 4th floor, it ask's me for a username and password.
After entering the password, it doesnt connect. It shows a blank screen with a flashing cursor.
If i connect to the switch directly via console port, i can see port uplink and downlinks but still cant do anything more.
have older laptop vista no picture blank screen new laptop window 7 can i hook them together
View 1 Replies View RelatedI tried to log on to my wireless routers IP address but it only gives me a blank page after signing in. the IP address is 192.168.1.1. Is there a problem with this ip address?
View 1 Replies View RelatedI'm encountering what I think is an issue on logging system on FW ASA 5520 - Asa Version 8.4(2), ASDM version 6.4(5). When I disabled the logging inside a rule from ASDM, or from console with the "log disable" option inside ACL, If I check in ASDM logging real time window I continue to see all the entry related to disabled rules. This is a correct behaviour about ASA logging ? How I can "hide" the entry related to disabled rules (this is what I need for troubleshooting purposes) ?
View 1 Replies View Relatedi just bought a netgear router. i was able get into routers login screen once. thought every thing is good? everything looked correct? now i cant get into login screen at all again. im confused it should be easy. either use 192.168.1.1 or 192.168.1.2 or 192.168.0.1 and 192.168.1.254. i tried them all with no luck.
View 3 Replies View RelatedWe are running DHCP Server on our cisco 1841 routers with 12.4 IOS. We want to maintian a Database of all the DHCP IP Leases by the server (ie router), the time and date of lease all the information in a Central / Branch Database.
View 2 Replies View RelatedI can't seem to satisfy with the RV180W. I've set a firewall block rule for certain traffice lan>wan, and I'd like to view the log.
Administratration | Firewall | Firewall Logs, I can select any or all items. Where do I view the log?
I can go to Logging | Logging Policies and select everything for the 'default' policy.
No matter what, I go to Status | View Logs, and select whatever severity level I want but get little to nothing, and definitely no firewall logging.
We're getting the following message in the logs when we ry to connect: encrypted Informational Exchange message is invalid because it is for incomplete ISAKMP SA
One of the router is a V2 and the other is a V4 if that makes any difference.
My first try at configuring my RV042 has had unexpected results. I set a WAN and LAN address, but did not enable remote managment and did not configure any port forwarding. I expected to be able to connect to the router on the LAN and I could. The surprise came when I put in my web address. I got a router login page. How do I suppress than on the WAN side. I have a static address with my ISP.
View 1 Replies View RelatedRecently i bought a Cisco RVS4000, upgraded the firmware to latest stable release (Firmware Version: V2.0.2.7) and started configuring it.Yesterday i found out that as the dsl connection drops (i'm using PPPoE with an ethernet ADSL Modem) the product stops logging, both locally and to an external configured syslog (which resides on a linux box over the LAN).
View 3 Replies View RelatedI have set the RV042 up for QuickVPN access. The router config recommends turning HTTPS on in the firewall when using QuickVPN. The side effect to this is any web browser throws me certificate errors and warns me not to continue logging in to the router's config. How do I fix this so the browser does not throw these messages?
Router is Linksys-branded, using latest firmware for this hardware (1.3.13.02-tm)
We have an RV082 setup with WAN to the internet and LAN IP of 192.168.188.1.If I add a static route like so:
network: 192.168.166.0
mask: 255.255.255.0
gateway: 192.168.188.2
hop count: 1
interface: LAN
The device with IP 192.168.188.2 will be connected directly to one of the LAN ports on the router.Will that work to route, trying to get to 192.168.166.0 to the IP of 192.168.188.2?It just seems odd because the packets would hit the router then go back out through the LAN port.
isco epc3925 in transparent bridge provided by isp with following wan details
ip=x.x.x.120 subnet=255.255.255.248 gw=x.x.x.121 and 2 dns server ip's
I can't get the one-to-one nat working. read in some forums that the rv082 can do the job.
I have a Meraki Firewall that sits behind my Cisco RV082. The Meraki is setup to run a VPN connection with my server but I am having problems passing the VPN traffic through properly.
I have 2 Uverse Internet Connections that the RV082 using load balancing so that they are shared. I have 10 static IP's.
I am trying to come in on one of my static IP addresses throught the Cisco RV082 to the Meraki and after doing a capture on the meraki it appears that it is starting to receive data to intiate the VPN connection but when it sends data back to the VPN client machine it never makes it.
I have reset my RV082 router (both wit the reset switch and the factory default wizard) and run the setup wizard but regardless I can't connect to shaw.ca which is my service provider. I notice that if I use http://192.168.1.1 the browsers (IE & FF) default to https://192.168.1.1 and then I am prompted for a certificate. I can enter if I ignore the request but after getting in I simply cannot connect to my ISP.
View 4 Replies View RelatedIs it possbile to NAT to other subnets with the RV082. It is on a 192.168.41.x and I have a phone system on a 192.168.20.x. After searching all over others are saying no.
View 4 Replies View RelatedI just set up a new Linksys/Cisco RV082 router with the intent to get VPN working from outside the building. I have gone through the setup and while everything looks good, I have not been able to connect yet. I have tried everything that I know how, and am now hoping to get the answer from some pros.
Here's my setup. We use Comcast Business class internet. The modem is plugged into WAN port 1 on the RV082. I'm using the router as a DHCP server, that is working fine. My local subnet is 192.168.0.0/220
Right now all I want is to be able to log in as a client using QuickVPN. I set up one user and a client to VPN tunnel using the router's config page. Here's the settings I have:
Tunnel Interface is setup on WAN1, checkbox is enabled.
Local Group Setup
Local Security Gatewaytpe: IP Only
Local Security Group Type: Subnet
[Code]....
It seems like something is blocking the connection, but seeing that I have tried this after disabling the firewall completely it doesn't make sense to me. I also went into the config page for the modem and set up the router as a DMZ. I have also tried connecting with the client built into Windows 7, but that doesn't work either, I just get "connection failed with error 619"
I have the port in QuickVPN set to auto, but have tried both 443 and 60443 with same results.
I ran a port scan at [URL] and it shows I have 3 ports open...80,443, and 1723
I have a VPN tunnel from one RV082 to another, first router has IP range of 192.168.1.0 and the second one has range of 18.18.18.0, the connection works fine, here is where the issue starts, I am at a PC in the 18.18.18.0 network and I ping an IP in the other one e.g. 192.168.1.50 and it pings fine, but when I try to RDP into it or do anything to it I get no response, is it a firewall issue? Is it a NAT issue? I am at a loss, now that IP i mentioned does have RDP enabled and working because it is being port fowarded in the 192.168.1.0 router and I can access it through the public IP.
Also a workstation with a static IP 192.168.1.18 I can ping it if im in the local network but if I am in the remote one I cannot at all.
we have an RV082 router that a few days ago started restarting itself after normal usage.The simpton is that when people come to office, starting using the Internet the RV082 resets. It stays online for 3 to 12 minutes and then it resets again.
clicking on Reset to Factory Default in the web interfaceafter the reset, I confirmed that it was reset to factory default I reset it again using the reset buttomre-configure the RV082 manually.I also tested with another identical rv082 (hw version and firmware version) and after doing a backup of the config of the original rv082 and restoring it in the new rv082, the same problem happends.
I have an RV082 10/100 8-Port VPN Router and have configured the NAT table to allow for remote users, however I've run into an issue. It seems like there is a limited number of entries that you can put in the table,10, and I need to configure about 5 more IPs. Any way to expand the NAT table, or alternatively recommend a different router. I would also be willing to add another router to the network, but I have little experience doing that.
View 3 Replies View RelatedAre the RV042 and RV082 routers SIP AWARE?I haven't had any luck finding documentation stating such.
View 2 Replies View RelatedJust purchased a RV082 and once I switched a bunch of users over to it I can no longer access the web admin section. I have tried using both IE and Firefox and have used multiple workstations. I get to the login screen but it doesn't get any further. I am running the latest firmware v4.0.4.2-tm. It works for a while then just stops. The only fix is to turn off the device and back on and then it starts working again.
I've seen this issue on other small business cisco devices and had to stop using this because of this issue and switch to a higher grade cisco product but was hoping that this particular issue would have been resolved now across cisco's products.
I just migrated our office network router to a RV082. While configuring it, I came across three problems:
(1) From our ISP we have four public IP addresses which I want to make use of for outbound traffic. With the previous router we used we could configure LAN IPs(ranges) to map to static public IPs. Does RV082 support this? I could not find an option for that at the web-interface. From what I understand the 1-1 NATing only goes both incoming and outgoign ways and actually is 1-1 and not the many-to-one I am looking for.
(2) How is it possible to configure incoming port forwards to use a specific WAN interface? Will it always be the primary WAN interface?
(3) Does the telnet access provide more configuration options? I could not log in to it with the same user credentials as with the web-interface.
Serial Number : NKS1532xxxxFirmware Version : v4.0.4.02-tm (Jul 4 2011 13:30:56)PID VID : RV082 V03Firmware MD5 Checksum : 1f84d8d0a2a8b99f9bfa4409e64547aaLANWorking Mode : Gateway
we have a RV082 and have the DMZ option enable for a range of IPs within the same subnet of WAN IP and this works great. I have another range of Public IPs from our ISP that is not in the same subnet of the WAN IP and do not see a way on the RV082 to include this 2nd bank of Public IPs in the DMZ. Our ISP internet feed plugs into the RV082 WAN port and we have a switch pulgged into the DMZ port of the RV082 that is used to connect the public devices in the current DMZ. Both banks of Public IPs from our ISP come over via the ISP internet feed plugged into the WAN Port. My question is, if I cannot configure a DMZ rule to allow this 2nd range of Public IPs to "travel" to the RV082 DMZ port.
View 0 Replies View RelatedI would like to set the subnet mask off the lan to 255.255.240.0 but the selection menu do not allow to do it.
View 8 Replies View RelatedI wanted to know if you can connect a Cable modem to a SA520W, then connect a RV082 to the SA520W?
View 5 Replies View RelatedWe recently moved our network over to RV082 router and its working great, well now we want to take advantage of VPN for our sales staff.
I was able to setup the VPN and using a PC at a remote office I can launch the quick connect and it connects right away, RV0 even shows the user connected. However the user cannot ping anything on our network via name or IP, connect to any resources, etc...
My understanding was when the client VPN would connect the user would get an IP from DHCP (this is on our Server 2008 DC) and they would be using that address, but when I run IPCONFIG on the client PC they just have there standard IP from remote office.