I tried to configure two RV042 working together. [code] WAN2 of both Router1 and Router2 are unused (unplugged). However, the Host2 can never ping to Host1. So as to Host1. Should I need to configure the protocol binding for all the traffic to the WAN1?
View 3 RepliesI have a RV042 VPN Router with the latest firmware v4.2.1.02.This Router is connected to the main site by a VPN Tunnel.
Now, I like to configure some DHCP Option so I can put a IP Phone behind the RV042. The IP Phone should receive a IP by DHCP from the RV042 and of course, the IP of the Call Manager with the Option 150.
I can configure DHCP and it works fine but I can't find where I have or can configure Option 150.
I need configuring Cisco RV042 dual wlan and port forwarding for 2 servers web and dns in LAN
View 1 Replies View RelatedI've purchased a Linksys RV042 hoping I could connect my two ISP.Both of them are 1/1 Mb, first is DSL second PPPoE connection.The problem is that on system summary page it doesn't show me that second WAN is connected. Even when I trying to manually connect to Internet it doesn't work.
When this connection is in Load balance Mode, internet is very slow, sometimes it's even disconnected.
My question is:How to configure Load Balance properly?I've tried this page:
[URL]...
I have tried replacing a loaner RV082 V2 with an RV042 V3 router with firmware 4.0.4.02. All worked well, including the site to site VPN. However, in spite of the fact that I have ports 443 and 4125 forwarded to the server (192.168.2.10), we are unable to connect via RWW. There is no such problem with the RV082. What is different with the way we configure these V3 routers for port forwarding?
View 2 Replies View RelatedCisco RV042 Dual WAN VPN Router -how to configure dynamic DNS without having to use the pre-programmed DDNS companies that are populated by default if my DDNS company is not listed and you cannot manually enter another company that is not on the list?
View 1 Replies View RelatedI've had 1 to 1 NAT setup for years now with no issues and the other day it simply stopped working. Rebooted everything, had ISP clear arp on their cable modem yet nothing going. As soon as I remove the 1 to 1 NAT on the router the PC has internet access. Add the 1 to 1 back and no out going internet. The configuration is pretty basic and has not changed.Thinking it could be a hardware issue I swapped it out with another RV042 I have with the exact config, same thing 1 to 1 NATs have no internet access. Upgraded one of the RV042 firmware to Firmware Version: 1.3.13.02-tm, had cable modem replaced, spent numerous calls with ISP. nada
I have found one interesting thing however, any internal machine which is set to dhp works fine, and static ip that does not have a 1 to 1 nat works fine and the last ip in the 1 to 1 nat range works fine. If I extend the range it is always only the last ip that works. Even if I add 1 to 1 nats one line at a time, it is always the last entry that works..
So have a RV042 VPN router that is directly connected to the ethernet port of our comcast cable modem.
If I connect to it using QuickVPN (1.4.2.1) from a PC that is connected using AT&T 3G Network it works fine!
If I connect to it using QuickVPN (1.4.2.1) from a different PC that is connected using home WiFi (linksys wrtxxx) then it fails. In the VPN log all I see is failure messages for ping.
2011/10/22 15:47:28 [WARNING]Failed to ping remote VPN Router!
If I open a regular command prompt and attempt to ping the VPN router it works so not understanding why the QuickVPN is unable to ping.
how I can troubleshoot this further. Makes me think the RV042 config is fine otherwise it would not work on a 3G connection. Something on the home PC or the home network. Not sure what to check.
Updated to newest firmware 4.2.1.02 and wanted to perform a backup of the startup configuration. I get a "The webpage cannot be found" HTTP 400 error when trying to do this backup. I have changed some settings since my last backup, but that backup was done using the last firmware revision.
View 3 Replies View RelatedI have set up an RV042 v1 and v3 both in Load Balancing mode. Set in Router mode.I want one of the WAN ports to be preferred so I added a static route to 0.0.0.0 metric 5 to that WAN.Sometimes the route shows in the routing table and sometimes it goes away!!
View 2 Replies View RelatedWhen my RV042 is accessed for long transmissions (svn check out, usually after 20 minutes ) the client receives a message "Gateway not responding, do you want to wait".
When this happens I see the following in the RV042 system log (the first 3 lines of the log below are normal):
Apr 2 17:36:53 2012Connection AcceptedTCP 192.168.2.2:8888->192.168.1.5:50046 on ppp1Apr 2 17:36:54 2012Connection AcceptedTCP 192.168.2.2:8888->192.168.1.5:50046 on ppp1Apr 2 17:36:54 2012Connection
[Code]....
We bought an RV042 at the end of June. It is used as a gateway and VPN router. DHCP server is disabled and all IPs are configured manually.Every once in a while (Tuesday night, then Friday night - yesterday, it has hapened once or twice before that) the router appears to restart (see log below) then comes back up with system time of Jan 01 2010. At this point the router will no longer load its configuration page (https://10.29.238.197:16443/) and VPN connection to our customer in Africa drops. However, devices behind the router can be reached and can access the internet. The only way to fix this is to power cycle the router at which point everything starts working flawlessly again.The PID VID is RV042 V03 running firmware v4.0.3.03-tm (May 12 2011 21:27:37). Our RV042 is a newer one with Cisco SMB Router branding not the older Linksys branding.
From the log when the router reboots:
Aug 12 22:38:42 2011VPN Log(g2gips0) #141: retransmitting in response to duplicate packet; already STATE_QUICK_I2Jan 1 01:00:05 2010System Logheart : System is upJan 1 01:00:13 2010System LogWAN connection is up : 10.29.238.197/255.255.255.192 gw 10.29.238.225 on eth1Jan 1 01:00:15 2010VPN Log(g2gips0) #1: [Tunnel Negotiation Info] >>> Initiator Send Main Mode 1st packet
I looked at the log more and all the usual messages assosciated with VPN being established are there - the last thing in the log before the router coming back up again is:
Jan 1 01:03:49 2010VPN Log(g2gips0) #4: [Tunnel Negotiation Info] Quick Mode Phase 2 SA Established, IPSec Tunnel ConnectedJan 1 01:03:49 2010VPN Log(g2gips0) #4: [Tunnel Negotiation Info] Quick Mode Phase 2 SA Established, IPSec Tunnel ConnectedJan 1 01:03:49 2010VPN Log(g2gips0) #4: sent QI2, IPsec SA established {ESP=>0x575a01c0 <0x6534ae4e
So it even claims the tunnel should be up but I can never reach anything on the far side.
My organization has deployed 3 Cisco RV042 (v3) at our 3 sites. They have been working pretty well up until about a week ago. One of them continues to route traffic and perform port-forwarding, but the VPN has completely stopped working and I can no longer access the web administration interface. I get the standard login page, but any attempt to login (with correct or incorrect password) takes maybe 5 minutes with a spinning status icon, followed by a blank page leaving the browser at: url...
I have the router logs e-mailed to me, and I can see that the system boots up with Jan 1 2010 as the system date, but it eventually gets the correct date from NTP, so I'm doubting this is causing the problem.
These were working for months prior to this happening, and even a reboot of the affected RV042 does not allow me to log into it or setup the VPN tunnels. I have found similar threads on this forum: url...
We have an RV042 on firmware version 1.3.13.02 and 2 ISPs:
WAN1 = Telepacific T1
1.5Mbps down and 1.5Mbps up
WAN2 = AT&T U-Verse
12Mbps down and 5Mbps up
I have it set to Load Balance, Primary WAN = WAN2
Network Service Detection enabled, only pinging the Remote Host of 4.2.2.2 and set to Generate Log
Bandwidth is set to:
WAN1 = 1000Kbps upstream & downstream
WAN2 = 5040Kbps upstream & 12000Kbps downstream
It seems to pick WAN1 a lot of the time. Do I have something setup wrong?
I have my RV042 set up in Dual WAN mode and both WANs are working properly. I would like to configure WAN1 to handle all traffic, unless it fails and then have everything to go to WAN2. Pretty much what Smart Link Backup does, however with that enabled only 1 of the WANs is live at any given time. I'd like both WANs to always be live as I'm going to see the second one as a back-door into the network. Is this possible to do with routing? I tried setting a routing rule to have everything to go WAN1, but when WAN1 goes down, nothing is rounted via WAN2.
View 0 Replies View RelatedAny working configuration to connect the iPad VPN-client (IPSEC) to the RV042?
View 16 Replies View RelatedI have a 6 month old RV042 with the newest firmware (v4.2.1.02). Over the weekend I configured the DMZ which after a lot of trial and error, was able to get working. Prior to configuring DMZ, I was able to log in with remote management. However now remote management no longer works. I've tried:
- Rebooting the router
- Turning the firewall off/on
- Turning remote management off/on
- Changing the remote management port
The only step I haven't taken is resetting the router back to factory defaults and trying to reconfigure it all again. This router is so finicky I have no faith I'd be able to get my current functionality back again.
I have a RV042 router on a single WAN and an internal LAN. I have configured port forwarding as follows: HTTP[TCP/80~80]->10.0.0.6HTTPS[TCP/443~443]->10.0.0.6IMAP[TCP/143~143]->10.0.0.5IMAP SSL[TCP/993~993]->10.0.0.5SMTP SSL[TCP/587~587]->10.0.0.5
Everything works just fine when I have the firewall DISABLED. However, when I enable it the behaviour is erratic. 1 out of 10 attempts to connect to ANY port forwarded works. Almost all attempts time out. Notice that this happens even if using only the default firewall rules (which should be bypassed by the port forwarding as I read in other posts).
My second try was to create firewall rules manually, overriding the default ones. I tried adding rules from source WAN1 (where my connection is) to ANY and to SINGLE IP's on every port. Nothing seems to work.
I don't know what I'm doing wrong, this is really bugging me. I had to turn the firewall off so we can access our servers from outside the office. This shouldn't have to be done.
Just found out that my firewall is getting LOTS and LOTS of Blocked - SYN Flood entries. I think this is why we are having trouble with the firewall. Could this be the problem? I have no idea where all these SYN packets are coming from since they appear with spoofed IPs or come from different bots all over.
Is there a way to set up a Site-to-site VPN between RV042 & Cisco 2911? I "googled" this and obtained a document, but it is not regarding Cisco 2911: [URL]
Routers are needed to setup it successfully. I have tried on both routers several configuration steps, no success...
How can I configure VPN connection between Cisco RV042 and Fritz!box 7170?I can establish VPN channel with Linksys RV042 with firmware 1.3.12.6-tm. When I set the same setting to Cisco RV042 (firmware v4.0.2.08-tm) VPN channel is not established.
View 1 Replies View Relatedconfigure ip-sec vpn tunnel between ASA5525x and RV042
View 5 Replies View RelatedI have RV042 and E4200 routers . I tried the manual UPnP port forwarding using Rv042 router and was succesful ( by typing 192.168.1.1 in the explorer and logged in using user name and password )
I am using a linux embedded system whose Internal IP ,Internal port are mapped .This system is connected to one of the LAN ports
I want to try auto UPnP port forwarding both for RV042 router and Linksys E4200 routers
After enabling the Upnp option only and logging out ,Can i add a port mapping entry in this router without logging in using a C++ program which runs on linux embedded system .
I was looking for a small business router that has VPN support and dual WAN support for load balancing. Upon reading reviews, I think RV042/RV042G is a good choice. Now am thinking if it supports intervlan/ router-on-a-stick configuration?
View 5 Replies View Relatedwhen entering Remote group 0.0.0.0/0.0.0.0 to establish a VPN, and all communication is not working.You do not know how to set up-work?
View 1 Replies View RelatedI have an I pad 1, a Linksys RV042 At My Office. And a Cisco RV042 at my Home
However I'm Creating PPTP Connection on my I pad For Both VPN , Office is Connection, but Home is not Connecting. I tried to connect to Home Thru any PC, And It is Working. Any Issues With I pad and Cisco Firmwares and Software?
how i can configure the Cisco RV042 to access PPTP VPN Server (Witopia VPn) or other vpn servers.
View 1 Replies View RelatedOn my RV042 (I used it for a couple of years now without issues), the DIAG led light amber (steady). It's not documented in the user manual.User manual says only:,Diag (Red) The Diag LED lights up when the Router is not ready for use. It turns off when the Router is ready for use.",Router does not work anymore and I can't access its web page as I used to do before this problem.I did a reset to factory default (reset button hold for more than 30 sec.) but it didn't change anything.
View 1 Replies View RelatedI have a remote location that has a Linksys/Cisco RV042 router [URL] that allows PPTP connections based on username and password combinations. There are no intermediary routers between this device and the internet - only a DSL modem. A secondary WAN connection is not present.
I am able to dial into this VPN using the Windows XP and Windows 7 dialers from any of my local free-wifi locations(e.g. Starbucks). I WAS able to connect to this VPN connection from my house when my home router was a Buffalo brand router.
I have replaced the Buffalo router with a 2620(non-XM) that is connected in ROaS fashion to a 2950 switch. I need some guidance on what in my config is not allowing me to connect to this remote site.
Home network info: Local subnets : 192.168.x.x
Remote network info: Local subnet : 10.214.x.x
The Windows XP dialer client indicates that the username and password challenge is where the connection fails. It ultimately gives me the error code 619. I have performed a Wireshark packet capture of an attempt to connect from ip 192.168.10.11. This packet capture shows multiple "Configuration Request" packets being exchanged between the two endpoints, but does not ever show an exchange of authentication.
My nat translation table shows an entry for both a GRE tunnel as well as port 1723 between 192.168.10.11 and the WAN port of the RV042 when attempting to establish this VPN.
I have attached my 2620 configuration for your review.
I have two Internet connections-
1-DSL Modem (WAN1-Internet Port)
2-Cable Modem-Comcast (WAN2-DMZ/Internet Port)
I connected the DSL (WAN1-Internet) port in and the Cisco RV042 was able to get an IP automatically. I tested the connection and it works just fine. Then I connect the Cable Modem-Comcast (WAN2-DMZ/Internet Port) in and I have the RV042 automatically optain IP address. But it just says 0.0.0.0. I've tried release/renew and that does nothing. Also, when I connect the 2nd Internet connection the Internet goes down. The only way it goes back up is when I disable under the PORT MANAGMENT setting.
All the settings have been kept to the default.How can I get the router to obtain an IP address from the Cable Modem-Comcast (WAN2 DMZ/Internet Port).
We have an Cisco RV042. We need to setup a VPN with a business partner who is already using our current IP scheme on another VPN with another client. They have asked us to NAT our IP's from 192.168.25.x to 192.168.245.x
I can't seem to figure this out on this router. I have done it on a Sonicwall and Watchguard, but can't seem to get it to work on the RV042.
I have setup the VPN and the One-To-One NAT. The tunnel will connect (using the 245.x IP as our local IP on the VPN setup), but no traffic will pass through.
i was planed to make a vpn over rv042 so i get the rv042 connected behind a thosmon 456(configured as a bridge) and 1 static ip ... and i configured the vpn and worked great ...but due to some circumstance i get a package of 6 ips insted of the old ip , so when i try to configure the router with the ISP they but the wan ip 10.232.x.x and told me that an internal ip from there lan ... and give me the 6 ip of 196.x.x.x to use as 1 for internal interface for the rv042 and 5 for the pc's,now the vpn not working anymore...notice: when try to configure the vpn tunnle in the local securty setting i mark the ip only and the ip that abear is the wan ip 10.232.x.x but i can't ping that ip beside i can ping the internal ip of the router 196.x.x.50does rv042 can support static and virtual ip inside the lan |! can i configure the thomson as pppoe and use one static ip from 196.x.x.x as wan ip for it ... and use anther 196.x.x.x ip for the rv042 to get access from outside and connect the lan to the rv042 with internal ip 192.168.x.x ...so i can access the vpn from outside .....and can connect the device i need to use static ip to the thomson ...
View 0 Replies View RelatedFirmware v4.0.4.02 has a nasty bug in the VPN section. If you switch to "IP by DNS Resolved" (yes, it says "Resolved" instead of "Resolution". Gotta love all the Engrish in the RV042!), it will automatically populate the field with "@yourdomain.com". This will cause the VPN to not lookup the proper IP address. Simply deleting the atmark after it populates will fix the problem.
Let's see what happens when we validate a Cisco RV042 webpage:
Errors found while checking this document as HTML 4.01 Transitional!
Result: 353 Errors, 1 warning(s)
Don't even get me started on the horrible Javascript...
i am trying to make a simple Site to SiteVPN between two offices, one has Cisco ASA and one has RV042 router.when traffic initiated from ASA side, i keep getting this message in Debug and tunnel wont come up
.
[IKEv1]: Group = A.A.A.139, IP = A.A.A.139, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.Apr 26 00:15:53 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
whereas if traffic initiated from RV042 side, i keep getting this message in debug and tunnel wont come up.
Apr 26 00:43:44 [IKEv1 DEBUG]: IP = RV.RV.RV.139, Oakley proposal is acceptableApr 26 00:43:44 [IKEv1 DEBUG]: IP = RV.RV.RV.139, IKE SA Proposal # 1, Transform # 0 acceptable Matches global IKE entry # 6Apr 26 00:43:44 [IKEv1]: IP = RV.RV.RV.139, Connection landed on tunnel_group RV.RV.RV.139Apr 26 00:43:45 [IKEv1]: IP = RV.RV.RV.139, Connection landed on tunnel_group RV.RV.RV.139Apr 26 00:43:45 [IKEv1]: Group = RV.RV.RV.139, IP = RV.RV.RV.139, Freeing previously allocated memory for authorization-dn-attributesApr 26 00:43:45 [IKEv1]: Group = RV.RV.RV.139, IP = RV.RV.RV.139, PHASE 1 COMPLETEDApr 26 00:43:45 [IKEv1]: IP =RV.RV.RV.139, Keep-alive type for this connection: DPDApr 26 00:43:45 [IKEv1 DEBUG]: Group =
[code].....