Updated to newest firmware 4.2.1.02 and wanted to perform a backup of the startup configuration. I get a "The webpage cannot be found" HTTP 400 error when trying to do this backup. I have changed some settings since my last backup, but that backup was done using the last firmware revision.
View 3 RepliesI have 16 customers using RV042 router all 11 have the RV042 router different ISP's. After eleminating every thing else we were down to the routers. Two of the customers we built linux boxes to do the routing and firewalling and VPN, etc. Once in place the problems went away. Which confirmed it was the RV042 router causing the problem.
We watched the traffic and after about 2 hrs the router tells both ends to reset. End of communication.
My question is how do we stop the router from terminiating the connections. They are not bandwith hogs. They are nessessary connect connections.
We have 2 dsl lines coming in and the modem is in bridge mode while the router handles the pppoe information. Each line is 6mb down and .5 mb up. It's ****, yes I know, but this is pretty decent for a small town in the country. To double our bandwidth, I put it in load balance mode. When load balance, I get anywhere from 9-12 down and .8 up. Here's where it gets tricky.
When anything is uploaded, the speed drops from 9-12 down and .8 up to about .2-.7 down and .2 up. I realize that we will lose some down and up speed but I wouldn't think it would be this drastic. Is this normal?When they upload to a specific https site (file is about 50mb), it never initiates the upload. If I switch it to Link Backup, it will upload fine. I still lose the speed but at least it does something. I've read that some https sites have issues with grabbing data from multiple IP's so I figured this is the case since it's a medical site that was probably developed in house. Is this true?Does protocol binding work in Load Balance mode? I binded all http and https traffic through WAN 2 interface however, when I do a speed test or check my external IP, it is not indicating the WAN 2 IP address. Is this a common issue in rv042's or is there a firmware update that solves all these issues?
I've had 1 to 1 NAT setup for years now with no issues and the other day it simply stopped working. Rebooted everything, had ISP clear arp on their cable modem yet nothing going. As soon as I remove the 1 to 1 NAT on the router the PC has internet access. Add the 1 to 1 back and no out going internet. The configuration is pretty basic and has not changed.Thinking it could be a hardware issue I swapped it out with another RV042 I have with the exact config, same thing 1 to 1 NATs have no internet access. Upgraded one of the RV042 firmware to Firmware Version: 1.3.13.02-tm, had cable modem replaced, spent numerous calls with ISP. nada
I have found one interesting thing however, any internal machine which is set to dhp works fine, and static ip that does not have a 1 to 1 nat works fine and the last ip in the 1 to 1 nat range works fine. If I extend the range it is always only the last ip that works. Even if I add 1 to 1 nats one line at a time, it is always the last entry that works..
I tried to configure two RV042 working together. [code] WAN2 of both Router1 and Router2 are unused (unplugged). However, the Host2 can never ping to Host1. So as to Host1. Should I need to configure the protocol binding for all the traffic to the WAN1?
View 3 Replies View RelatedSo have a RV042 VPN router that is directly connected to the ethernet port of our comcast cable modem.
If I connect to it using QuickVPN (1.4.2.1) from a PC that is connected using AT&T 3G Network it works fine!
If I connect to it using QuickVPN (1.4.2.1) from a different PC that is connected using home WiFi (linksys wrtxxx) then it fails. In the VPN log all I see is failure messages for ping.
2011/10/22 15:47:28 [WARNING]Failed to ping remote VPN Router!
If I open a regular command prompt and attempt to ping the VPN router it works so not understanding why the QuickVPN is unable to ping.
how I can troubleshoot this further. Makes me think the RV042 config is fine otherwise it would not work on a 3G connection. Something on the home PC or the home network. Not sure what to check.
I have set up an RV042 v1 and v3 both in Load Balancing mode. Set in Router mode.I want one of the WAN ports to be preferred so I added a static route to 0.0.0.0 metric 5 to that WAN.Sometimes the route shows in the routing table and sometimes it goes away!!
View 2 Replies View RelatedWhen my RV042 is accessed for long transmissions (svn check out, usually after 20 minutes ) the client receives a message "Gateway not responding, do you want to wait".
When this happens I see the following in the RV042 system log (the first 3 lines of the log below are normal):
Apr 2 17:36:53 2012Connection AcceptedTCP 192.168.2.2:8888->192.168.1.5:50046 on ppp1Apr 2 17:36:54 2012Connection AcceptedTCP 192.168.2.2:8888->192.168.1.5:50046 on ppp1Apr 2 17:36:54 2012Connection
[Code]....
We bought an RV042 at the end of June. It is used as a gateway and VPN router. DHCP server is disabled and all IPs are configured manually.Every once in a while (Tuesday night, then Friday night - yesterday, it has hapened once or twice before that) the router appears to restart (see log below) then comes back up with system time of Jan 01 2010. At this point the router will no longer load its configuration page (https://10.29.238.197:16443/) and VPN connection to our customer in Africa drops. However, devices behind the router can be reached and can access the internet. The only way to fix this is to power cycle the router at which point everything starts working flawlessly again.The PID VID is RV042 V03 running firmware v4.0.3.03-tm (May 12 2011 21:27:37). Our RV042 is a newer one with Cisco SMB Router branding not the older Linksys branding.
From the log when the router reboots:
Aug 12 22:38:42 2011VPN Log(g2gips0) #141: retransmitting in response to duplicate packet; already STATE_QUICK_I2Jan 1 01:00:05 2010System Logheart : System is upJan 1 01:00:13 2010System LogWAN connection is up : 10.29.238.197/255.255.255.192 gw 10.29.238.225 on eth1Jan 1 01:00:15 2010VPN Log(g2gips0) #1: [Tunnel Negotiation Info] >>> Initiator Send Main Mode 1st packet
I looked at the log more and all the usual messages assosciated with VPN being established are there - the last thing in the log before the router coming back up again is:
Jan 1 01:03:49 2010VPN Log(g2gips0) #4: [Tunnel Negotiation Info] Quick Mode Phase 2 SA Established, IPSec Tunnel ConnectedJan 1 01:03:49 2010VPN Log(g2gips0) #4: [Tunnel Negotiation Info] Quick Mode Phase 2 SA Established, IPSec Tunnel ConnectedJan 1 01:03:49 2010VPN Log(g2gips0) #4: sent QI2, IPsec SA established {ESP=>0x575a01c0 <0x6534ae4e
So it even claims the tunnel should be up but I can never reach anything on the far side.
My organization has deployed 3 Cisco RV042 (v3) at our 3 sites. They have been working pretty well up until about a week ago. One of them continues to route traffic and perform port-forwarding, but the VPN has completely stopped working and I can no longer access the web administration interface. I get the standard login page, but any attempt to login (with correct or incorrect password) takes maybe 5 minutes with a spinning status icon, followed by a blank page leaving the browser at: url...
I have the router logs e-mailed to me, and I can see that the system boots up with Jan 1 2010 as the system date, but it eventually gets the correct date from NTP, so I'm doubting this is causing the problem.
These were working for months prior to this happening, and even a reboot of the affected RV042 does not allow me to log into it or setup the VPN tunnels. I have found similar threads on this forum: url...
We have an RV042 on firmware version 1.3.13.02 and 2 ISPs:
WAN1 = Telepacific T1
1.5Mbps down and 1.5Mbps up
WAN2 = AT&T U-Verse
12Mbps down and 5Mbps up
I have it set to Load Balance, Primary WAN = WAN2
Network Service Detection enabled, only pinging the Remote Host of 4.2.2.2 and set to Generate Log
Bandwidth is set to:
WAN1 = 1000Kbps upstream & downstream
WAN2 = 5040Kbps upstream & 12000Kbps downstream
It seems to pick WAN1 a lot of the time. Do I have something setup wrong?
I have my RV042 set up in Dual WAN mode and both WANs are working properly. I would like to configure WAN1 to handle all traffic, unless it fails and then have everything to go to WAN2. Pretty much what Smart Link Backup does, however with that enabled only 1 of the WANs is live at any given time. I'd like both WANs to always be live as I'm going to see the second one as a back-door into the network. Is this possible to do with routing? I tried setting a routing rule to have everything to go WAN1, but when WAN1 goes down, nothing is rounted via WAN2.
View 0 Replies View RelatedAny working configuration to connect the iPad VPN-client (IPSEC) to the RV042?
View 16 Replies View RelatedI have a 6 month old RV042 with the newest firmware (v4.2.1.02). Over the weekend I configured the DMZ which after a lot of trial and error, was able to get working. Prior to configuring DMZ, I was able to log in with remote management. However now remote management no longer works. I've tried:
- Rebooting the router
- Turning the firewall off/on
- Turning remote management off/on
- Changing the remote management port
The only step I haven't taken is resetting the router back to factory defaults and trying to reconfigure it all again. This router is so finicky I have no faith I'd be able to get my current functionality back again.
I have a RV042 router on a single WAN and an internal LAN. I have configured port forwarding as follows: HTTP[TCP/80~80]->10.0.0.6HTTPS[TCP/443~443]->10.0.0.6IMAP[TCP/143~143]->10.0.0.5IMAP SSL[TCP/993~993]->10.0.0.5SMTP SSL[TCP/587~587]->10.0.0.5
Everything works just fine when I have the firewall DISABLED. However, when I enable it the behaviour is erratic. 1 out of 10 attempts to connect to ANY port forwarded works. Almost all attempts time out. Notice that this happens even if using only the default firewall rules (which should be bypassed by the port forwarding as I read in other posts).
My second try was to create firewall rules manually, overriding the default ones. I tried adding rules from source WAN1 (where my connection is) to ANY and to SINGLE IP's on every port. Nothing seems to work.
I don't know what I'm doing wrong, this is really bugging me. I had to turn the firewall off so we can access our servers from outside the office. This shouldn't have to be done.
Just found out that my firewall is getting LOTS and LOTS of Blocked - SYN Flood entries. I think this is why we are having trouble with the firewall. Could this be the problem? I have no idea where all these SYN packets are coming from since they appear with spoofed IPs or come from different bots all over.
I need some info on how to open an RV042 config backup (.exp) file. I recently had an RV042 that got very wet and it is now dead, and I do not have another on hand. BUT I do have the config Backup that includes the user MAC authentication list that I really need. Is there a way to get this information other than loading into another RV042.
View 4 Replies View Relatedwe are running Prime NCS 1.1.1.124 and we want to upgrade to PI1.3. I installed the point patch which worked well. after the point patch i wanted to start a backup which can be imported to the new PI1.3 appliance. but i cant do any backups anymore. no on localdisk, not on a remote repository. i was doing 3 backups (2 local disk, one remote ftp disk with the same output) with "debug backup-restore all". output follows.
/admin# 7 [4508]: backup-restore:backup: br_backup.c[431] [daemon]: initiating application component backup backup-20130405-0913 to repos defaultRepo
7 [4508]: backup-restore:backup: br_backup.c[454] [daemon]: no staging url defined, using local space
7 [4508]: backup-restore:backup: br_backup.c[41] [daemon]: flushing the staging area
7 [4508]: backup-restore:backup: br_backup.c[477] [daemon]: creating /opt/backup/backup-backup-20130405-0913-1365196396(code)
I have a problem with the router Linksys RV042, I made a backup of it that contains a file with the extention .exp Now we have buy a new Rv042 made by cisco and the backup file is .config the question is how I convert the .exp file to a .config file so I can Restore the backup in to the new router?
View 1 Replies View RelatedWe have an issue with View db (Monitoring & Reports) backup on ACS, version 5.2.0.26. We have scheduled incremental backup daily and full backup monthly. Everything has been working well, but since yesterday following errors have appeared, and full and incremental backup stopped working:
Alarm Name
System Alarm [Incremental Backup]
Cause/Trigger
On-demand Full Backup failed
Alarm Details
CARS_BR_BACKUP_CREATE : -405 : Internal error: couldn't create backup file
Alarm Name
[code]....
We use same repository as always. Backup to the same repository works from CLI.
I have RV042 and E4200 routers . I tried the manual UPnP port forwarding using Rv042 router and was succesful ( by typing 192.168.1.1 in the explorer and logged in using user name and password )
I am using a linux embedded system whose Internal IP ,Internal port are mapped .This system is connected to one of the LAN ports
I want to try auto UPnP port forwarding both for RV042 router and Linksys E4200 routers
After enabling the Upnp option only and logging out ,Can i add a port mapping entry in this router without logging in using a C++ program which runs on linux embedded system .
I was looking for a small business router that has VPN support and dual WAN support for load balancing. Upon reading reviews, I think RV042/RV042G is a good choice. Now am thinking if it supports intervlan/ router-on-a-stick configuration?
View 5 Replies View Relatedwhen entering Remote group 0.0.0.0/0.0.0.0 to establish a VPN, and all communication is not working.You do not know how to set up-work?
View 1 Replies View RelatedI have an I pad 1, a Linksys RV042 At My Office. And a Cisco RV042 at my Home
However I'm Creating PPTP Connection on my I pad For Both VPN , Office is Connection, but Home is not Connecting. I tried to connect to Home Thru any PC, And It is Working. Any Issues With I pad and Cisco Firmwares and Software?
On my RV042 (I used it for a couple of years now without issues), the DIAG led light amber (steady). It's not documented in the user manual.User manual says only:,Diag (Red) The Diag LED lights up when the Router is not ready for use. It turns off when the Router is ready for use.",Router does not work anymore and I can't access its web page as I used to do before this problem.I did a reset to factory default (reset button hold for more than 30 sec.) but it didn't change anything.
View 1 Replies View RelatedI'm planning to buy a few Cisco RV082's for remote offices and using them to connect to main office Cisco 2851 site to site vpn. So I guess, simple site to site vpn will work without much problem, but I wonder, will backup vpn feature work as expected on backup WAN channel and how should I configure it on the IOS side?
View 1 Replies View RelatedI have a remote location that has a Linksys/Cisco RV042 router [URL] that allows PPTP connections based on username and password combinations. There are no intermediary routers between this device and the internet - only a DSL modem. A secondary WAN connection is not present.
I am able to dial into this VPN using the Windows XP and Windows 7 dialers from any of my local free-wifi locations(e.g. Starbucks). I WAS able to connect to this VPN connection from my house when my home router was a Buffalo brand router.
I have replaced the Buffalo router with a 2620(non-XM) that is connected in ROaS fashion to a 2950 switch. I need some guidance on what in my config is not allowing me to connect to this remote site.
Home network info: Local subnets : 192.168.x.x
Remote network info: Local subnet : 10.214.x.x
The Windows XP dialer client indicates that the username and password challenge is where the connection fails. It ultimately gives me the error code 619. I have performed a Wireshark packet capture of an attempt to connect from ip 192.168.10.11. This packet capture shows multiple "Configuration Request" packets being exchanged between the two endpoints, but does not ever show an exchange of authentication.
My nat translation table shows an entry for both a GRE tunnel as well as port 1723 between 192.168.10.11 and the WAN port of the RV042 when attempting to establish this VPN.
I have attached my 2620 configuration for your review.
I am looking to setup a solution for backing up a Metro Ethernet connection on a 2951 using an 1841 and 2 T1's in a Multilink. The Metro E will be primary, and if the BGP peer goes down, I want it to switchover to the 1841. Can it be done and is there an example of the BGP setup to work off of?
View 1 Replies View RelatedVPN tunnel backup is not available on the RV016 firmware version 4.0.2.08 (it IS on the RV082. The data sheet and the manual for the RV016 is wrong. I have purchased several RV016 hardware V3 and several RV082 hardware V3. Both have the same current firmware version. We have noted that the RV016 does not have the VPN tunnel failover option found in the RV082. It also does not have split DNS (noted in the manual. A I would have thought that the firmware would provide equal options on the RV042, RV082, and RV016.
View 2 Replies View RelatedJust recently purchased an RVS4000 to take the place of an old NetGear FVS336, which supported multiple NAT translations. It appears that the RVS4000 does not support this, any other models in the small business line support this? I only need this for a backup Internet connection?
View 4 Replies View RelatedIs there a way to view the contents of the .exp file generated from exporting the configuration from RV082? I've got a couple of RV082 that have the same rules, but want to compare the configuration.
View 2 Replies View RelatedI'm replacing an older (& failing) RVS4000 v1 with a new V2. I need to minimize downtime. Will a config backup from the old v1 restore properly to a new v2 (all have newest firmware)? There are a lot of tweaks including several VPNs and to do it all manually is not desirable.
View 2 Replies View RelatedI'm trying to move from a faulty SRP527 to SRP 547 - I tried a Restore from Backup, but it doesn't work.So start from fresh, and I'm having an issue trying to add a 2nd SSID to a VLAN...
I keep getting the error:
"FAILED! SSID 2 has joined another VLAN"
Except it hasn't... its not assigned to any VLAN...
My backup userid, password, privi 15 on all our company routers Say around 300 routers, it is difficult to log in each router and create a backup account, i heard from one of my friend that i can create a backup account and can upload thru the kiwicat tool and it will automatically creates my backup account on all the routers. Procedure to create this.
View 6 Replies View Related