Cisco Routers :: RV042 Killing Off Site Backup After About 2 Hrs
Dec 23, 2011
I have 16 customers using RV042 router all 11 have the RV042 router different ISP's. After eleminating every thing else we were down to the routers. Two of the customers we built linux boxes to do the routing and firewalling and VPN, etc. Once in place the problems went away. Which confirmed it was the RV042 router causing the problem.
We watched the traffic and after about 2 hrs the router tells both ends to reset. End of communication.
My question is how do we stop the router from terminiating the connections. They are not bandwith hogs. They are nessessary connect connections.
View 3 Replies
ADVERTISEMENT
Dec 29, 2012
Is there a way to set up a Site-to-site VPN between RV042 & Cisco 2911? I "googled" this and obtained a document, but it is not regarding Cisco 2911: [URL]
Routers are needed to setup it successfully. I have tried on both routers several configuration steps, no success...
View 3 Replies
View Related
Mar 25, 2013
I have no problem configuring both devices to successfully connect when the juniper firewall isn't in the picture. But due to policy; the RV042 at our main site must sit behind the firewall.
I've got the port forwarding setup but I'm not able to connect. I know I"m missing some configuration on the RV042 but I can't think of it! I've attached a GIF to give an example of both setups.
View 3 Replies
View Related
Apr 23, 2013
I have got two CISCO RV042 .I need to configure a site to site VPN .
View 1 Replies
View Related
Nov 28, 2012
I recently bought two RV042s to create a site to site VPN for a client. I have several of these setups installed at other locations but this is the first version 3 hardware I've used.It seems like the dynamic IP functionality of the VPN setup may not be working correctly. I've verified all settings on each router match and have deleted/recreated the setup several times just to make sure. Here's the logs from the router with a static IP.
Nov 29 06:49:51 2012 VPN Log (g2gips0): deleting connection
Nov 29 06:49:51 2012 VPN Log added connection description (g2gips0)
Nov 29 06:49:51 2012 VPN Log listening for IKE messages
Nov 29 06:49:51 2012 VPN Log forgetting secrets
Nov 29 06:49:51 2012 VPN Log loading secrets from '/etc/ipsec.d/ipsec.secrets'
Nov 29 06:49:51 2012 VPN Log (g2gips0): cannot initiate connection without knowing peer IP address
Nov 29 06:49:51 2012 VPN Log (g2gips0): cannot initiate connection without knowing peer IP address
I've tried both dynamic IP + email and dynamic IP + FQDN to authenticate the router using the dynamic IP and both give the same error as above.I did a firmware update hoping to fix PPPoE which seemed to be broken with a Netopia modem in bridge mode so both routers are on the latest firmware, v4.2.1.02.
View 18 Replies
View Related
Oct 15, 2012
May I know can the 2 models WRVS4400N and RV042 perform site-to-site vpn with each other?
View 1 Replies
View Related
Jan 24, 2013
I have an RV042 connected to another RV042 via site-to-site VPN. The tunnel has been solid for months, but when I did an actual read/write test between PCs at either endpoint, the speeds were quite slow.
Endpoint A has a line speed of 25/5.
Endpoint B has a line speed of 50/7-ish.
Read/write test from A to B was about ~3 write and ~7 read. Does this sound normal for these routers? I was hoping for better performance than that.
View 1 Replies
View Related
Jun 21, 2012
Updated to newest firmware 4.2.1.02 and wanted to perform a backup of the startup configuration. I get a "The webpage cannot be found" HTTP 400 error when trying to do this backup. I have changed some settings since my last backup, but that backup was done using the last firmware revision.
View 3 Replies
View Related
Nov 14, 2011
We have 2 dsl lines coming in and the modem is in bridge mode while the router handles the pppoe information. Each line is 6mb down and .5 mb up. It's ****, yes I know, but this is pretty decent for a small town in the country. To double our bandwidth, I put it in load balance mode. When load balance, I get anywhere from 9-12 down and .8 up. Here's where it gets tricky.
When anything is uploaded, the speed drops from 9-12 down and .8 up to about .2-.7 down and .2 up. I realize that we will lose some down and up speed but I wouldn't think it would be this drastic. Is this normal?When they upload to a specific https site (file is about 50mb), it never initiates the upload. If I switch it to Link Backup, it will upload fine. I still lose the speed but at least it does something. I've read that some https sites have issues with grabbing data from multiple IP's so I figured this is the case since it's a medical site that was probably developed in house. Is this true?Does protocol binding work in Load Balance mode? I binded all http and https traffic through WAN 2 interface however, when I do a speed test or check my external IP, it is not indicating the WAN 2 IP address. Is this a common issue in rv042's or is there a firmware update that solves all these issues?
View 2 Replies
View Related
Oct 23, 2012
Having some issues getting a site to site VPN connected between two RV042. Any experience getting this to work behind a Motorola SBG9000.Will I be able to get this working? Or will I have to organise a cable modem through my ISP instead
View 1 Replies
View Related
Nov 15, 2010
So here is my issue. I have two sites, each with a Linksys RV042 on thier site.
Site 1:
External: 142.142.142.142
Internal: 192.168.25.0/24
Site 2:
External: 143.143.143.143
Internal: 192.168.26.0/24
We have setup a site-to-site VPN between these sites, and all traffic is running back and forth without isse.
At Site 1 we have configured the Client VPN for use with the QuickVPN software. Again, for site 1, this is not an issue. We are able to access all internal resources at Site 1 without issue (expect for some DNS related problems).
The problem that we have is attempting to access Site 2 resources via the QuickVPN connection at Site 1. Even though they are not suppose to exist, we are able to ping 192.168.26.1-6 (which are ghost addresses likely created by the RV042's) but no actual systems on at Site 2.
I have added the Client VPN connection at Site 2, but it has the same problem accessing resources at Site 1.
View 6 Replies
View Related
Mar 13, 2011
I have 2 ASA 5505 Firewall, I Configured Site 2 Site VPN no both the fitrewall, as i have a dual ISP, i am able to create the tunnel with primary but once my primary is down i am not able to create the tunnel with back up ISP. During the troobleshoothing by typing Show isakmp sa and Show ipsec sa, i can see my tunnel is up, but not able to decap the packets.
As it will look like
#pkts encaps: 15, #pkts encrypt: 15, #pkts digest: 15 #pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0 #pkts compressed: 0, #pkts decompressed: 0 #pkts not compressed: 15, #pkts comp failed: 0, #pkts decomp failed: 0 #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0 #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0 #send errors: 0, #recv errors: 0
View 4 Replies
View Related
Feb 2, 2011
We are attempting to implement a VPN configuration using an ASA 8.02 at a Central site which terminates remote site VPN connections from IOS routers (12.4), using static crypto maps. We have a functional configuration, but looking to implement a backup site-site configuration on the ASA, using different service providers. The observation is that as soon as i add the 'connection-type originate-only' to the crypto map on the ASA, the tunnel is fatally broken. As soon as statement is removed the tunnel comes is restored. just wanted to confirm that the 'connection-type originate-only' configuration on the Central ASA is supported with the Cisco IOS peer. Documentation seems to indicate there is some sort of proprietary exchange that is supported only between ASA peers.
View 7 Replies
View Related
Jul 6, 2012
how to configure a site-to-site VPN between RV042 router and 1941 router?
View 0 Replies
View Related
Sep 3, 2012
I'm trying to establish a site to site VPN using ipsec between an RV220W in the UK and an RV042 in Italy to no avail.The RV042 tells me it's "waiting for a connection" and it gives 0.0.0.0 as the remote address (i'm using Dynamic addressing at both ends). I can ping the remote address with a response.The basic parameters I'm using is 3DES with SHA1, but the RV042 offers an option for Perfect Forward Secrecy which the RV220W does not (I've tried toggling this) and the RV220W offers and Extended Authentication mode which I can't see on the RV042.
View 2 Replies
View Related
Mar 7, 2013
I configured every thing in both site, there is a connection between my sites BUT I can't access my resources from Site B with it has RV042. It also shows that it connected to my ASA in Site A but there is no traffic between sites !!! I don't know what should I do now ?
View 2 Replies
View Related
May 7, 2012
I am trying to set up a Site to Site between two RV042 with static IP at both routers.at the log at site 1 i get: packet from XX.XXX.XX.167:5: initial Main Mode message received on 10.2.32.1:500 but no connection has been authorized with policy=PSK.At site 2 i get: packet from xxx.xxx.xxx.146:500: initial Main Mode message received on 192.168.1.1:500 but no connection has been authorized with policy=PSK.I have tuned off the firewall and added a Port forwarding to the router ip and port 500.Tried with different autentication methods, but get the same message.
View 1 Replies
View Related
Nov 8, 2012
My problem is VPN Site2Site between Cisco and Linksys routers: after a troubles vpn tunnel now seems up but no data is passed accross tunnel.This is configuration of Linksys RV042 (Firmware Version: 1.3.12.6-tm, seems last for this hardware [code]
View 1 Replies
View Related
Aug 2, 2009
I need some info on how to open an RV042 config backup (.exp) file. I recently had an RV042 that got very wet and it is now dead, and I do not have another on hand. BUT I do have the config Backup that includes the user MAC authentication list that I really need. Is there a way to get this information other than loading into another RV042.
View 4 Replies
View Related
Mar 13, 2013
Is it possible to have a site-to-site IPSEC tunnel between 2 identical RV110W routers?I basically want one of them to initiate a secure tunnel with the second so that computers from one router subnet see the computers from the other router subnet.
View 3 Replies
View Related
May 19, 2013
the RV110W IPSEC site-to-site tunnel, are there necessary 2 x public IPs for it to work, or only 1 public IP is enough? [code]If it works with 1 public ip, the "CLIENT" RV110W configuration should be straightforward (in Advanced VPN SetupRemote Endpoint i fill in the dyndns address?), but how do i setup "HOST" RV110W?
View 2 Replies
View Related
Mar 6, 2012
The process is IP Input and I'm not really sure how to troubleshoot it. I've read through all the doc's on high cpu load if I shutdown the port that feeds that network, CPU drops to around 30%, bring it back up and it jumps up to 90%+. I've got a policy map on the interface shaping the traffic
[code]...
View 19 Replies
View Related
Jan 7, 2011
I have been using a linksys 5 port workgroup switch in my room. I have the ethernet cable coming from the router into the uplink port and my PS3, xbox, dvr, and pc in the other ports. It has been working fine until today I started messing around the the cables. I had trouble with the ps3 connecting to the internet so I used my laptop with wifi disabled to test out a few of the cables and ports. Now all of a sudden the switch kills the internet connection. If I remove the cable running to my room from the main router, the other PCs and wireless will connect, but as soon I plug myself up it goes dead. I now have the ethernet cable in my room hooked directly to the PC bypassing the switch and everything works fine now.
View 3 Replies
View Related
Apr 5, 2011
This has finally become a BIG problem. Any time I have iTunes running and downloading podcasts, it hogs all the bandwidth for the Internet (but not the local network). This is not only slowing down access from the machine running iTunes and the downloads but for every other device trying to web browse.I'm running two Macs and one Windows/Dell PC on the network. All are hard-wired (Ethernet) to the DIR-655. How to throttle iTunes? I did some research and found that I am apparently not the only one having this issue.I'm about to bail on iTunes entirely and try to get used to Miro, which does allow bandwidth control.
View 3 Replies
View Related
Jun 11, 2013
We recently purchased an SRP527W router because of its capability to configure site-site VPN tunnels. The configuration of IKE and IPSEC is working and the tunnel comes up but the problem is that the router is passing our internal IP addresses through the tunnel. The remote end we are connecting to requires us to hide all traffic behind one IP address which would ideally be our external static IP address from our ISP.
View 1 Replies
View Related
Dec 19, 2011
As you can see i have problems with connecting 2 SRP521W together for an VPN tunnel. I tried as much as I can but now i dont know what to do or how and where is the mistake? the connection between these two devices was there last week, after weekend (nothing changed in configs) the connection suddenly was interrupted, without any reason or warning. another day it worked again and 20 mins later connection was dead again...and now it wont establish at all.. here are some screenshots from the vpnconfigs of my devices. one has a static IP the otherone uses FQDN. These are the IKE policies: Here the IPsec Policies: and the GRE policies:
View 10 Replies
View Related
Sep 6, 2011
I have an ASA5505 running which is on a static IP. I have just got an SRP527W for a remote worker and want to create a site-to-site VPN into the ASA. I have a number of other router of non-cisco brand which just all dial-in and connect no problem.
On other routers I have been abloe to specify the DDNS hostname in the VPN setup so that the ASA can identify it. I'm not sure how I setup the SRP527 to connect to the ASA.
View 3 Replies
View Related
Sep 2, 2012
i'm trying to create a VPN IPSEC link between 2 offices. The VPN link is created, and i can communicate but only one way. Clients in Office B seems to have routing problem.
Details :
Office A :
- SRP527W router.
- Client Network : 192.168.0.0 / 24
[Code].....
View 5 Replies
View Related
Dec 18, 2011
Can I use a single Public IP address for both Internet access and site to site vpn access?If not, can I configure the RV220W as a bridge and still use it via another gateway configured for vpn passthrough as a VPN appliance/server on the LAN?
View 3 Replies
View Related
Dec 6, 2012
We have successfully establish a site-to-site vpn, but we have some difficulties when PPTP users try to access the remote network linked by this tunnel. LAN users can access the remote network without problem, but users who are connected remotly to the lan (PPTP) can't access computer on the remote network. Is there a way to allow PPTP user to access the remote network ? Adding a route ?
View 1 Replies
View Related
Oct 25, 2011
I'm installing a new SRP547W for a client and am having trouble setting up a site-to-site vpn. They are using the WAN1 ADSL interface for their internet connection. When I add a sub interface to it I am unable to see the 'Connection Type' drop down like I can see on a WAN2 ethernet sub interface. I have followed the instructions on page 29 provided here: how I can get a a site to site vpn set up on this router using either PPTP or L2TP over the ADSL interface.
View 1 Replies
View Related
Dec 23, 2011
I have two Cisco RV220W routers and I would like to realy DHCP from the home office to the remote office accross the IPsec Tunnel. Is this possible and if so how?
I have already gone into the IPv4 LAN (Local Network) settings on the remote router and set the DHCP mode to "DHCP Relay" providing the internal ip address of the home office router as the remote DHCP server.
View 1 Replies
View Related
Feb 9, 2013
I am considering to buy two RV180Ws and place them on two separate locations. But before buying I would like to make sure that the units meets my requirements. Lets call the locations A and B. I would like to connect location A with full network access to location B. But at the same time I would like to have that location B also gets full access to the network at location A.Besides this I would like to be able to connect to one of the networks from remote with my laptop.Preferably all connections should be made using IPSEC and not PPTP.I would like to know if it is possible to make such a configuration, and eventually if there is a smarter way to do e.g. only letting clients connect to location A or B and granting them access to all ressources at both location A and B from there.
View 1 Replies
View Related
