Linksys Switch Has Started Killing The Dsl Connection
Jan 7, 2011
I have been using a linksys 5 port workgroup switch in my room. I have the ethernet cable coming from the router into the uplink port and my PS3, xbox, dvr, and pc in the other ports. It has been working fine until today I started messing around the the cables. I had trouble with the ps3 connecting to the internet so I used my laptop with wifi disabled to test out a few of the cables and ports. Now all of a sudden the switch kills the internet connection. If I remove the cable running to my room from the main router, the other PCs and wireless will connect, but as soon I plug myself up it goes dead. I now have the ethernet cable in my room hooked directly to the PC bypassing the switch and everything works fine now.
View 3 Replies
ADVERTISEMENT
Jul 6, 2012
Recently, i bought a LinkSys WAG120N ANNEX-A to replace my old speedstrem4200. Well everything was fine, but after 2 days of it installed, it started to drop my ADSL connection.
Sometimes, it remain connected for 4-5 hours, then drop, or sometimes, it drop every 30min-1hour.I tried upgrading the firmware to 1.00.16, but no luck, it still drop the connection.I have 3 computer plugged to the router via cable(wired) plus 1 netbook(wireless) and 1 ipod (wireless).Sometimes, when 1 computer is turned off, it seem to make the ADSL connection drop when the LAN light turn off. I noticed everytime it drop the ADSL connection, in the logs, i get this:
Mon, 2010-11-08 22:24:57 - Terminating on signal 15. Mon, 2010-11-08 22:24:57 - Enter: tdb_store. Mon, 2010-11-08 22:24:57 - tdb_store: calling tdb_update. Mon, 2010-11-08 22:24:57 - Enter: tdb_update. Mon, 2010-11-08 22:24:57 - Enter: tdb_store. Mon, 2010-11-08 22:24:57 - tdb_store: calling tdb_update. Mon, 2010-11-08 22:24:57 - Enter: tdb_update. Mon, 2010-11-08 22:24:57 - Enter: tdb_store. Mon, 2010-11-08 22:24:57 - tdb_store: calling tdb_update. Mon, 2010-11-08 22:24:57 - Enter: tdb_update. Mon, 2010-11-08 22:24:57 - Couldn't increase MTU to 1500. Mon, 2010-11-08 22:24:57 - Couldn't increase MRU to 1500 Mon, 2010-11-08 22:24:57 - LCP down. Mon, 2010-11-08 22:24:58 - Modem hangup Mon, 2010-11-08 22:24:58 - Connection terminated. Mon, 2010-11-08 22:24:58 - Connect time 215.0 minutes. Mon, 2010-11-08 22:24:58 - Sent 50496235 bytes, received 212267122 bytes. Mon, 2010-11-08 22:24:58 - Enter: tdb_store. Mon, 2010-11-08 22:24:58 - tdb_store: calling tdb_update. Mon, 2010-11-08 22:24:58 - Enter: tdb_update. Mon, 2010-11-08 22:24:58 - Doing disconnect Mon, 2010-11-08 22:24:58 - Exit.
I tried changing the MTU settings in the router to 1492 (my ISP default) but didnt work.
Tried changing the MTU to 1492 on every computer and still got the same problem.For now im using the WAG120N in bridge mode, and still using my old speedstream4200 as ADSL modem.
View 5 Replies
View Related
Apr 12, 2012
So I bought this new E4200v1 about a week ago and since yesterday it started dropping connection terribly. After checking Cisco Connect it seemed to have a Firmware update which I did and after it was done I decided to do a factory reset since I read somewhere that it works. When the router came back on for a second I saw an unsecured SSID, but then it turned into an SSID called panelist-ssid with a password called google-4panel which is definitely not the default. Also, when I try to access the router webpage to configure it, the password is not the old one nor the default Username: blank Password: admin credentials. I am currently connected to it via the button on the back that allows me to connect without password. Another thing is that I uninstalled Cisco Connect and when I try to install at 25% it says it cannot find my router and ask for SSID + password which I input yet it fails.
View 9 Replies
View Related
Sep 10, 2012
My 2960-24TC-L switch is startet up and shows up: switch.Have tried to upload new image with xmodem without success.There must be a procedure to upload the new image, I have looking for hours and can not find the procedure.
View 3 Replies
View Related
Sep 15, 2012
I had a strange issue with one of my customer..Cisco WS-C3750X-48P Access switch was not reachable and after reload it started working.I would like to know the root cause of the issue. There were no logs and no errors in interfaces.Even Cpu utilization was not high. We have enabled arp inspection and dhcp snooping in the switch..Hope this will not make any issue..Also we have dot1x enabled on port..
View 5 Replies
View Related
Jun 17, 2012
I have had intermittent problems with this PCI 802.11n adapter since I installed it. There isn't a new driver available, so that's not a solution. Issue is despite a strong signal, WiFi connection breaks sometimes when a session (either e-mail or browser) is started.The bar signal indicator goes from 5 bars to none, and mouse-over shows "no connection." About half the time the PC locks up (frozen cursor, no response to ctrl-alt-del, etc.).some of the time, the PC recovers after several minutes or more, other times locks up completely and the PC must be either forced reset or powered down manually. I've run CC Cleaner and check out the registry but can't find anything that works. PC is a 2.4GHz Celeron 1GB RAM running WinXP SP3 with all updates.Not related to browser; behavior is the same with Firefox, Chrome, IE. Also, other PCs on same network have no issues.On occasion I've triggered the lock-up while I had performance monitor running, and in the cases where the machine resumed running by itself, history showed no overloads typical of lock-ups. This PC is used almost exclusively for basic e-mail and browsing.
View 1 Replies
View Related
Mar 6, 2012
The process is IP Input and I'm not really sure how to troubleshoot it. I've read through all the doc's on high cpu load if I shutdown the port that feeds that network, CPU drops to around 30%, bring it back up and it jumps up to 90%+. I've got a policy map on the interface shaping the traffic
[code]...
View 19 Replies
View Related
Apr 5, 2011
This has finally become a BIG problem. Any time I have iTunes running and downloading podcasts, it hogs all the bandwidth for the Internet (but not the local network). This is not only slowing down access from the machine running iTunes and the downloads but for every other device trying to web browse.I'm running two Macs and one Windows/Dell PC on the network. All are hard-wired (Ethernet) to the DIR-655. How to throttle iTunes? I did some research and found that I am apparently not the only one having this issue.I'm about to bail on iTunes entirely and try to get used to Miro, which does allow bandwidth control.
View 3 Replies
View Related
Dec 23, 2011
I have 16 customers using RV042 router all 11 have the RV042 router different ISP's. After eleminating every thing else we were down to the routers. Two of the customers we built linux boxes to do the routing and firewalling and VPN, etc. Once in place the problems went away. Which confirmed it was the RV042 router causing the problem.
We watched the traffic and after about 2 hrs the router tells both ends to reset. End of communication.
My question is how do we stop the router from terminiating the connections. They are not bandwith hogs. They are nessessary connect connections.
View 3 Replies
View Related
May 21, 2012
I am using Vista 32bit and connect to the internet via a Linksys router and have cable modem. When I start my computer, it will not connect to the internet. I have to disconnect and reconnect my network cable and it starts working fine. This is very annoying. Another similar computer is connected to the same router and doesn't have this problem. how to make my computer connect to the internet automatically without having to do this each time I boot up my PC?
View 2 Replies
View Related
Dec 19, 2012
no changes except switched out old steady wrt45g router cabled to different computer for a new (crazy good price) asus n66 dark knight. stable old system after clean install xpsp3 several years ago. abruptly started crashing and endless rebooting any time wusb54g attached. no antivirus active. never had linksys monitor software installed. xp had handled everything well till now. repeated attempts to re-install drivers (rt25000usb) fail. occasionally xp sees "new hardware" and occasionally it simply immediately crashes. attempted install of ?failing? usb54gv4 onto much newer W7 machine to try to test hardware w/o success. linksys AE1000 usb adapter worked on W7 machine and also installed successfully on the old steady XP machine in question.
View 3 Replies
View Related
Feb 20, 2012
My E4200 recently started to randomly shut down. To say the least this is very aggravating. Nothing has changed, location still the same and it seems to be overheating or in the very least getting warm. In the last It will also shut down multiple times a day too. I have done some reading and am beginning to regret this purchase.
View 8 Replies
View Related
Jan 27, 2012
My WRT400n has started dropping the wireless signal 4 to 5 times a day. Somet times it fixes itself but most of the time I have to re-boot the router to connect a wireless signal.I looked for a firmware upgrade but there hasn't been one since 2009.
View 4 Replies
View Related
Sep 3, 2011
Upgraded to 1.0.04 from .03 and caused some problems. Worked great at first-upgrade was flawless-no problems there. THen it started dropping wireless connections. THen no wireless or wired connections. COuld not pull an IP address.Pulled power to router couple times and it worked great at first again then degraded like before.Held reset button for 5 secs to reset to factory defaults, now the setup display is missing all the html coding-no menu list. All in raw format.Am connected to port 1 via cat 5 to my laptop with no connections except the internet connection to the cable modem. Something has gone really wrong with my .04 software.Tried to find the .03 version, but the zip file is HUGE. Whats in it anyway?
View 1 Replies
View Related
Nov 8, 2012
I have a Linksys E2500 and recently the power led light on the back of the router started blinking. The router itself seems to be working fine. I can access the router and the router seems to be assigning the IP addresses fine. I did look up the issue on the knowledge base and tried all the solutions but the light is still blinking. Not sure what to do anymore.
View 5 Replies
View Related
Jan 5, 2011
Hard wired network (15 workstations.) I had a dsl modem connected to my network switch and linksys wrt54gs router connected to that modem. All hard wired workstations had internet access AND there was a wireless internet connection. With any wifi device I could access the internet.I switched from dsl to comcast. All hard wired work stations still have internet. but when I plug my wireless router into the modem (comcast business IP gateway) there is no wireless internet connection. The hard wired workstations can still get online and there IS a wireless network, but it does not allow internet access (page cannot be found etc.)
Comcast says it absolutely should work. Linksys says it requires simple reconfig of router settings (reset router, clone mac address.) I have read knowledge base articles from linksys and followed each step. The lan ports of the modem are all working if I connect to them directly with a laptop and cable. I have reset router multiple times, cloned mac address, dhcp release/renew.
My physical connections are correct. In the router set up utility, I can see the mac adrdress and ip address but can't tell if the IP is from the modem or the router. Default gateway is always 192.168.1.1 in the router AND in any workstation ipconfig screen. Ip addresses are 192.168.1.xx in ipconfig at any workstation AND in the router set up status.
I cannot access internet via router even if plugged directly into it. It is as if the router is not getting the correct information from the modem. However, it worked perfectly with the DSL modem the day before we changed.My workstations are all hard wired and work. I simply want to have Wi-Fi also... for phones and laptops w wireless etc.
View 8 Replies
View Related
Jan 2, 2013
I have a problem with my switch. The model no. of the switch is as follows:
Linksys SRW2048 10/100/1000 48 Ports
Serial No: RJT00GC00395 GGR2906 MM
1. I am creating a home computer lab. I do have 3 servers HP ProLiant DL 385 G1. Two of them have 6 gigabit ports where as the third server has 2 gigabit ports.
2. Installed ESXi 5.1 on two servers where as installed FreeNAS on the third server and configured it as iSCSI storage and NFS storage.
Problem:
1. Every port works perfectly fine. However, when I keep connecting the ports of the switch to the ports of servers, internet gets disconnected.
2. Interestingly, my wireless internet also gets disconnected, the ports of the switch does not have any internet now.
3. This happens till I connect above 8-9 ports of the switch to the servers.
3. However, when I remove the connection between the switch and the servers, internet comes, wireless internet starts working; and the port of the switch also gets internet connection when I check the internet connection of the individual ports one at a time.
Some more information:i do have internet service provided by Time Warner Cable. My internet speed is as follows:
Download Speed: Up to 15 Mbps
Upload Speed: Up to 1 Mbps
I do have a modem *** router by Motorola which has 4 gigabit ports.Model no: Motorola SURFboard SBG6580 i am assuming it is some thing related to bandwidth of the internet.
View 4 Replies
View Related
Mar 19, 2012
we using Linksys router for Internet for different vlans now we take 3750 as core switch for another different vlans 10,20 we create v Lans 20,20 also create cpd servers and we need Internet for vlans 10,20 through linksys router how should we configure?
View 5 Replies
View Related
Aug 8, 2012
I am facing this issue with my LMS setup. the rmedbengine is not getting started. The CW was down due to low memory space . After restart the RMEDBEngine is not coming up(Made some free space avaiable in the drive) . I have done transaction log recovery. Wher i find the issue saying " database cannot be started - no error " for rme database. Attached the error SC.
View 1 Replies
View Related
Feb 6, 2012
I have a number of Catlyst 2750 switched as well as some wireless AIR-AP1131 access points that I would like to better manage. Some of the IOS are out of date, need to look at setting up VLAN's etc etc
I downloaded Cisco Network Assistant v 5.7(1) but when I do a network scan it just says every single device is Unsupported.I have a new 3750G-24PS sat here that I bought just before Christmas and I would like to configure it.
View 10 Replies
View Related
Jan 17, 2011
when i trying to share on window xp based computer and access to another computer it givs the message " The Server service not started
View 9 Replies
View Related
Oct 13, 2011
How do I get note pad started on my computer. When I want to print something the computer tells me I need to use notepad first.
View 1 Replies
View Related
Jul 2, 2012
I'm trying to go on the company of heroes 2 forum but when i try and load the page i get an error message saying "Ruby on rails application could not be started". Is this a problem with the web page or is it on my end?
View 1 Replies
View Related
Feb 18, 2013
We are running LMS 4.3.2, it was running OK... but now we receive the following message:
"User Tracking Major Acquisition cannot be started as Network Topology, Layer 2 Services and User Tracking are disabled."
All processes are running. System restart and re-install the 4.3.2 update does not fix it. I think this happens after a device update, maybe FaultManagementDeviceUpdate...
View 2 Replies
View Related
Jul 17, 2012
Ok so my internet connection has recently started disconnecting and reconnecting every 5 mins or so. It has never done this before and has started doing it out of the blue. It doesn't even appear to have cut out by the icon at the bottom but it does stuff like stop youtube videos from loading or when I am playing online poker or online gaming it will cut out for about 30 seconds before reconnecting again.
View 14 Replies
View Related
Oct 31, 2012
My computer has started connecting to the internet on startup, I do not want it to do this, the answer i have already seen on here for this does not work, so how can I stop this?
View 1 Replies
View Related
Feb 28, 2011
I am having this problem, the internet and the laptop started working slow so I restarted it, I've got stuck with this ip. Lan is working fine but wireles..
I have tried a few fixes:
1.Enter the stuff manually
2.Reboot router, laptop
3.Rollback
I also googled a lot and tried other fixes (which i dont remember) but nothing seemed to work. (Not including reinstalling windows)By the way im on Windows Xp sp3.
[code]...
View 3 Replies
View Related
Jan 16, 2011
I have a Intel DH55HC motherboard running windows 7 and the Intel 82578DC Ethernet controller is coming up with This device cannot start (code 10)I have loaded the prowin32 driver download from the Intel site and also re-done the BIOS as instructed and it still wont resolve.
View 1 Replies
View Related
Jan 24, 2013
Been having a weird problem recently, our internet normally runs around 4mb and was fine until around two months ago, when all of a sudden it started disconnecting and running really slowly. Normally around peak times, but also whenever the wife turns her laptop on.I know what you are about to say - Virus, exactly my first thought until I also noticed that whenever this happened the noise margin started jumping, or it would lose sync and resync at around 1.5mb, with high ping times and repeated dropped packets. Turning her laptop off seemed to solve dropped packets (although would stay slow and high ping times remain)We moved the laptop around the house and noticed this only happened when she sits on the sofa in the living room, bear in mind this sofa is a good 2 meters away from the nearest phone socket (which is not connected anyway) and works fine anywhere else, albeit in close proximity or not to the router / phone line.We cannot fathom why this is happening and have had a ticket open with Sky who have exhausted their capacity to resolve without fixing it.
View 1 Replies
View Related
Feb 20, 2013
I have an issue where I am trying to start my VPN and continually get the following message: Error 56: The Cisco Systems, Inc. VPN Service has not been started. Please start this service and try again.
So I have been into Services to 'start' Cisco Systems, Inc. VPN Services - this then always comes up with this error: Error 1053: The service did not respond to the start or control request in a timely fashion
The solution mentioned on other posts on disabling the ICS but it was already disabled. When I try to start VPNGUI I also get error 56 and when I try to use services.msc to start the service I get error 1053. Then also when I try to start from task manager services(cvpnnd) i get access denied.
View 1 Replies
View Related
Mar 6, 2013
The website [URL] started giving me this error : The server at forums.d2jsp.org is taking too long to respond. I am directly connected to my service provider's box (The brand is "Arris"). The issue seems to have started as soon as I uninstalled google chrome (reinstalling doesn't fix it). My last resort with reinstalling windows 7 64bit.
My service provider is Videotron (Quebec, Canada) I can see the front page directly from their IP adress: [URL] but as soon as I hit any link it goes back to the connection time out error.
The tracing route is :
1 7 ms 6 ms 5 ms 10.189.16.1
2 15ms 15ms 15ms 216.113.124.17
3 31ms 31ms 32ms 216113123.174
4 * * * Request timed out.
View 2 Replies
View Related
Jan 3, 2011
router started disconnecting clients every few minutes
View 2 Replies
View Related
Mar 13, 2011
I used ACS 4.2.1.15 on windows 2008 SP1, found CSLog service not started. I try to restarted but service was started for while and went to stopped.How should i do to start this service?
View 2 Replies
View Related
