I'm trying to go on the company of heroes 2 forum but when i try and load the page i get an error message saying "Ruby on rails application could not be started". Is this a problem with the web page or is it on my end?
View 1 Replies
one of our 2 ACE boxes in FT group suddenly reboot-ed from active state and now it continuously reboots with the following error:
insmod: error inserting '/isan/bin/klm_octeon_device.klm': -1 No such deviceerror inserting /isan/bin/klm_octeon_device.klmDaughter Card Not Found. Rebooting..INIT: Sending all processes the TERM signal...
I've got an MSE 3310 that came with four-post rails for rack mounting. These came without instructions and we are having a hard time figuring out exactly how they work. They say General Devices C-300-S-124-RC-MOD
View 4 Replies View RelatedThe datasheet contains the following regarding rails and brackets:
Cisco ASA 5512-X, 5515-X, 5525-X, 5545-X, 5555-X spare rail kit - ASA-RAILS=
Cisco ASA 5512-X, 5515-X, 5525-X brackets for rack mounting - ASA-BRACKETS=
The word spare seems to imply that it comes with a set of rails. Does the ASA-5515-X come with rails and brackets, or must both of these be ordered?
[URL]
I have a couple Dell R710 2U servers that came with the Dell quick rails. The rack I am trying to place them in is a 4-post open cabinet, but the depth of the posts are about an inch too short to allow the Dell quick rails to snap-lock to the square holes. Are there any 2U extenders I can attach to the back two posts of the cabinet to give the minimum length needed for the Dell quick rails to snap-lock? The extenders would also need to have the square holes.
View 3 Replies View RelatedI am facing this issue with my LMS setup. the rmedbengine is not getting started. The CW was down due to low memory space . After restart the RMEDBEngine is not coming up(Made some free space avaiable in the drive) . I have done transaction log recovery. Wher i find the issue saying " database cannot be started - no error " for rme database. Attached the error SC.
View 1 Replies View RelatedI have a number of Catlyst 2750 switched as well as some wireless AIR-AP1131 access points that I would like to better manage. Some of the IOS are out of date, need to look at setting up VLAN's etc etc
I downloaded Cisco Network Assistant v 5.7(1) but when I do a network scan it just says every single device is Unsupported.I have a new 3750G-24PS sat here that I bought just before Christmas and I would like to configure it.
when i trying to share on window xp based computer and access to another computer it givs the message " The Server service not started
View 9 Replies View RelatedHow do I get note pad started on my computer. When I want to print something the computer tells me I need to use notepad first.
View 1 Replies View RelatedWe are running LMS 4.3.2, it was running OK... but now we receive the following message:
"User Tracking Major Acquisition cannot be started as Network Topology, Layer 2 Services and User Tracking are disabled."
All processes are running. System restart and re-install the 4.3.2 update does not fix it. I think this happens after a device update, maybe FaultManagementDeviceUpdate...
I have been using a linksys 5 port workgroup switch in my room. I have the ethernet cable coming from the router into the uplink port and my PS3, xbox, dvr, and pc in the other ports. It has been working fine until today I started messing around the the cables. I had trouble with the ps3 connecting to the internet so I used my laptop with wifi disabled to test out a few of the cables and ports. Now all of a sudden the switch kills the internet connection. If I remove the cable running to my room from the main router, the other PCs and wireless will connect, but as soon I plug myself up it goes dead. I now have the ethernet cable in my room hooked directly to the PC bypassing the switch and everything works fine now.
View 3 Replies View RelatedOk so my internet connection has recently started disconnecting and reconnecting every 5 mins or so. It has never done this before and has started doing it out of the blue. It doesn't even appear to have cut out by the icon at the bottom but it does stuff like stop youtube videos from loading or when I am playing online poker or online gaming it will cut out for about 30 seconds before reconnecting again.
View 14 Replies View RelatedMy computer has started connecting to the internet on startup, I do not want it to do this, the answer i have already seen on here for this does not work, so how can I stop this?
View 1 Replies View RelatedI am having this problem, the internet and the laptop started working slow so I restarted it, I've got stuck with this ip. Lan is working fine but wireles..
I have tried a few fixes:
1.Enter the stuff manually
2.Reboot router, laptop
3.Rollback
I also googled a lot and tried other fixes (which i dont remember) but nothing seemed to work. (Not including reinstalling windows)By the way im on Windows Xp sp3.
[code]...
I have a Intel DH55HC motherboard running windows 7 and the Intel 82578DC Ethernet controller is coming up with This device cannot start (code 10)I have loaded the prowin32 driver download from the Intel site and also re-done the BIOS as instructed and it still wont resolve.
View 1 Replies View RelatedBeen having a weird problem recently, our internet normally runs around 4mb and was fine until around two months ago, when all of a sudden it started disconnecting and running really slowly. Normally around peak times, but also whenever the wife turns her laptop on.I know what you are about to say - Virus, exactly my first thought until I also noticed that whenever this happened the noise margin started jumping, or it would lose sync and resync at around 1.5mb, with high ping times and repeated dropped packets. Turning her laptop off seemed to solve dropped packets (although would stay slow and high ping times remain)We moved the laptop around the house and noticed this only happened when she sits on the sofa in the living room, bear in mind this sofa is a good 2 meters away from the nearest phone socket (which is not connected anyway) and works fine anywhere else, albeit in close proximity or not to the router / phone line.We cannot fathom why this is happening and have had a ticket open with Sky who have exhausted their capacity to resolve without fixing it.
View 1 Replies View RelatedI have an issue where I am trying to start my VPN and continually get the following message: Error 56: The Cisco Systems, Inc. VPN Service has not been started. Please start this service and try again.
So I have been into Services to 'start' Cisco Systems, Inc. VPN Services - this then always comes up with this error: Error 1053: The service did not respond to the start or control request in a timely fashion
The solution mentioned on other posts on disabling the ICS but it was already disabled. When I try to start VPNGUI I also get error 56 and when I try to use services.msc to start the service I get error 1053. Then also when I try to start from task manager services(cvpnnd) i get access denied.
The website [URL] started giving me this error : The server at forums.d2jsp.org is taking too long to respond. I am directly connected to my service provider's box (The brand is "Arris"). The issue seems to have started as soon as I uninstalled google chrome (reinstalling doesn't fix it). My last resort with reinstalling windows 7 64bit.
My service provider is Videotron (Quebec, Canada) I can see the front page directly from their IP adress: [URL] but as soon as I hit any link it goes back to the connection time out error.
The tracing route is :
1 7 ms 6 ms 5 ms 10.189.16.1
2 15ms 15ms 15ms 216.113.124.17
3 31ms 31ms 32ms 216113123.174
4 * * * Request timed out.
router started disconnecting clients every few minutes
View 2 Replies View RelatedI used ACS 4.2.1.15 on windows 2008 SP1, found CSLog service not started. I try to restarted but service was started for while and went to stopped.How should i do to start this service?
View 2 Replies View Relatedi want to activate flexible netflow on my WS-X45-SUP7-E with IOS cat4500e-universalk9.SPA.03.02.00.SG.150-2.SG. I've started with a simple configuration like this:
Configuring a Flow Monitor for IPv4/IPv6 Traffic Using the Flexible NetFlow
“NetFlow IPv4 Original Input” Predefined Record
SUMMARY STEPS
Yesterday I had a installation of LMS4.2.2 who was working fine. I followed the procedure to install VMware Tools on the virtual appliance on this thread url...
Now I have a problem with the processes of LMS, but maybe it is not linked. I forget to do a snapshot before installing VMware Tools so I need to find a solution. A whole bunch of services do not start know. I tried to uninstall the VMware tools, to regenerate SSL certificate, I rebooted the server several times. It is running under VMware 5.1. [code]
Im having a horrible problem with my internet connection where I cannot use any kind of download site such as filefront or anything really.The main problem is once a download gets going (any filesize above 1MB) the connection will stall out and stop downloading until the server says cannot download or if available, i pause and start the download again. Its very frustrating having to babysit downloads or be unable to even complete one ,My router is a netgear N150 WNR 1000.
View 14 Replies View RelatedI have had intermittent problems with this PCI 802.11n adapter since I installed it. There isn't a new driver available, so that's not a solution. Issue is despite a strong signal, WiFi connection breaks sometimes when a session (either e-mail or browser) is started.The bar signal indicator goes from 5 bars to none, and mouse-over shows "no connection." About half the time the PC locks up (frozen cursor, no response to ctrl-alt-del, etc.).some of the time, the PC recovers after several minutes or more, other times locks up completely and the PC must be either forced reset or powered down manually. I've run CC Cleaner and check out the registry but can't find anything that works. PC is a 2.4GHz Celeron 1GB RAM running WinXP SP3 with all updates.Not related to browser; behavior is the same with Firefox, Chrome, IE. Also, other PCs on same network have no issues.On occasion I've triggered the lock-up while I had performance monitor running, and in the cases where the machine resumed running by itself, history showed no overloads typical of lock-ups. This PC is used almost exclusively for basic e-mail and browsing.
View 1 Replies View RelatedI am using Vista 32bit and connect to the internet via a Linksys router and have cable modem. When I start my computer, it will not connect to the internet. I have to disconnect and reconnect my network cable and it starts working fine. This is very annoying. Another similar computer is connected to the same router and doesn't have this problem. how to make my computer connect to the internet automatically without having to do this each time I boot up my PC?
View 2 Replies View RelatedRecently, i bought a LinkSys WAG120N ANNEX-A to replace my old speedstrem4200. Well everything was fine, but after 2 days of it installed, it started to drop my ADSL connection.
Sometimes, it remain connected for 4-5 hours, then drop, or sometimes, it drop every 30min-1hour.I tried upgrading the firmware to 1.00.16, but no luck, it still drop the connection.I have 3 computer plugged to the router via cable(wired) plus 1 netbook(wireless) and 1 ipod (wireless).Sometimes, when 1 computer is turned off, it seem to make the ADSL connection drop when the LAN light turn off. I noticed everytime it drop the ADSL connection, in the logs, i get this:
Mon, 2010-11-08 22:24:57 - Terminating on signal 15. Mon, 2010-11-08 22:24:57 - Enter: tdb_store. Mon, 2010-11-08 22:24:57 - tdb_store: calling tdb_update. Mon, 2010-11-08 22:24:57 - Enter: tdb_update. Mon, 2010-11-08 22:24:57 - Enter: tdb_store. Mon, 2010-11-08 22:24:57 - tdb_store: calling tdb_update. Mon, 2010-11-08 22:24:57 - Enter: tdb_update. Mon, 2010-11-08 22:24:57 - Enter: tdb_store. Mon, 2010-11-08 22:24:57 - tdb_store: calling tdb_update. Mon, 2010-11-08 22:24:57 - Enter: tdb_update. Mon, 2010-11-08 22:24:57 - Couldn't increase MTU to 1500. Mon, 2010-11-08 22:24:57 - Couldn't increase MRU to 1500 Mon, 2010-11-08 22:24:57 - LCP down. Mon, 2010-11-08 22:24:58 - Modem hangup Mon, 2010-11-08 22:24:58 - Connection terminated. Mon, 2010-11-08 22:24:58 - Connect time 215.0 minutes. Mon, 2010-11-08 22:24:58 - Sent 50496235 bytes, received 212267122 bytes. Mon, 2010-11-08 22:24:58 - Enter: tdb_store. Mon, 2010-11-08 22:24:58 - tdb_store: calling tdb_update. Mon, 2010-11-08 22:24:58 - Enter: tdb_update. Mon, 2010-11-08 22:24:58 - Doing disconnect Mon, 2010-11-08 22:24:58 - Exit.
I tried changing the MTU settings in the router to 1492 (my ISP default) but didnt work.
Tried changing the MTU to 1492 on every computer and still got the same problem.For now im using the WAG120N in bridge mode, and still using my old speedstream4200 as ADSL modem.
no changes except switched out old steady wrt45g router cabled to different computer for a new (crazy good price) asus n66 dark knight. stable old system after clean install xpsp3 several years ago. abruptly started crashing and endless rebooting any time wusb54g attached. no antivirus active. never had linksys monitor software installed. xp had handled everything well till now. repeated attempts to re-install drivers (rt25000usb) fail. occasionally xp sees "new hardware" and occasionally it simply immediately crashes. attempted install of ?failing? usb54gv4 onto much newer W7 machine to try to test hardware w/o success. linksys AE1000 usb adapter worked on W7 machine and also installed successfully on the old steady XP machine in question.
View 3 Replies View RelatedI just Bought 1142N AP, I am unable to connect to it or open its Web interface, the Default IPs i am using are 10.0.0.1 for Router and 10.0.0.2 for my PC, whats its Default IP, What IP address should I put on PC, plus Do i need the IOS for the AP?
View 3 Replies View RelatedI have an ancient Compaq V2410 notebook which has started to drop my home Wifi connection recently (started about a week ago). At first, I thought it was the install of Firefox 8 as it froze and crashed but it happens with Chrome, IE and even when not running a browser.
My ISP is O2 in the UK and I have a DSL2+ service with the O2 Wireless Box II. I have gone through a power down cycle on the router and it continues to work with my ethernet-connected desktop PC. I have changed the Wireless Card in the notebook but fault is still intermittent. The notebook was also set to OpenDNS servers but that has been set back to Automatic DNS servers.
The notebook has the latest free versions of Avast Anti-virus & Comodo Firewall and the main issue is that the notebook has 640Mb system RAM which means that various Windows services have been Disabled or set to Manual.
I can sometimes recover the Wifi signal by switching the wireless on/off but it is sporadic. I have attached the Xirrus WiFi screenshots at startup, at fault state and at recovery state together with the ipconfig.txt output.
My E4200 recently started to randomly shut down. To say the least this is very aggravating. Nothing has changed, location still the same and it seems to be overheating or in the very least getting warm. In the last It will also shut down multiple times a day too. I have done some reading and am beginning to regret this purchase.
View 8 Replies View RelatedMy WRT400n has started dropping the wireless signal 4 to 5 times a day. Somet times it fixes itself but most of the time I have to re-boot the router to connect a wireless signal.I looked for a firmware upgrade but there hasn't been one since 2009.
View 4 Replies View RelatedJust this weekend, my DIR-655 has suddenly started blasting out continuous IGMPV2 Membership broadcasts, causing a flood of network traffic that's not normal and is interfering with other traffic. Rebooting everything in the system didn't fix it, turning off the other machines on the network (3 + NAS) didn't fix it, and I couldn't find anything in the configuration of the DIR-655 to stop it.
View 3 Replies View RelatedUpgraded to 1.0.04 from .03 and caused some problems. Worked great at first-upgrade was flawless-no problems there. THen it started dropping wireless connections. THen no wireless or wired connections. COuld not pull an IP address.Pulled power to router couple times and it worked great at first again then degraded like before.Held reset button for 5 secs to reset to factory defaults, now the setup display is missing all the html coding-no menu list. All in raw format.Am connected to port 1 via cat 5 to my laptop with no connections except the internet connection to the cable modem. Something has gone really wrong with my .04 software.Tried to find the .03 version, but the zip file is HUGE. Whats in it anyway?
View 1 Replies View Related
