Cisco WAN :: 2951 / 1841 - Backup Setup With 2 Routers And BGP?

Aug 20, 2012

I am looking to setup a solution for backing up a Metro Ethernet connection on a 2951 using an 1841 and 2 T1's in a Multilink. The Metro E will be primary, and if the BGP peer goes down, I want it to switchover to the 1841. Can it be done and is there an example of the BGP setup to work off of?

View 1 Replies


ADVERTISEMENT

Cisco WAN :: Configure Backup Redundant Link On 2951 With IOS 15.0?

May 15, 2012

We have 6 sites which are connected through E1 links.All sites connected from HQs.
 
Site A is HQs. 
Sited B, C, D, E, and F are Branches.
 Site A is directly connected with site B, C, D and E.
 Site D is connected with Site F.
 
Now we have another redundant E1 link for site C and Site F.we are using Static Routes.i have configured Qualified-next-hope on Juniper Router but i am unable to configure IP SLA on Site C Cisco 2951 with IOS 15.0 router.is there another solution for my scenario plz share with me for Redundant Link.

View 1 Replies View Related

Cisco Infrastructure :: 2811 / 1841 / WIC-1AM-V2 - Setup POTS Dial Connection Between 2 Routers?

Jun 17, 2012

I would like to set up a POTS Dial connection between 2 Cisco routers, using the modem card WIC-1AM-V2. I'd like to use this as an out-of-band connection to a remote site, if the primary internet connection fails. So, this setup will only be used in one direction, 1 router placing calls, the other one receiving calls.Here's my config of the receiving router:
 
chat-script dial "" ATZ AT OK "ATX3D T" ATS0=8 TIMEOUT 120 CONNECT C
interface Async0/2/0 description out of band for network no ip address encapsulation slip async mode interactive
line 0/2/0 session-timeout 5 absolute-timeout 10 script connection dial login local modem InOut transport input all escape-character BREAK autoselect ppp stopbits 1 speed 115200 flowcontrol hardware

[code]....
 
This config is working fine, when dialing in via a Windows Hyperterminal Dial connection. After a while of dialing I get the login prompt of the router.Now I want to have a router placing calls instead of a Windows Server. I can't figure out how to tell a router to place calls to a POTS phone number.
 
Receiving router: 2811, WIC-1AM-V2, IOS c2800nm-ipbasek9-mz.124-25a
Calling router: 1841, WIC-1AM-V2, IOS c1841-advsecurityk9-mz.124-25a

View 5 Replies View Related

Cisco Switching/Routing :: 2951 - HSRP Backup Taking Two Minutes When Switching Off Primary Router

Oct 7, 2012

I configure HSRP on Router 2951 as a primary router, and Router 2811 as backup router. But when I am switching off my Primary router the backup router is  taking 2 mins to take over form primary router. 
 
 [code]....

View 4 Replies View Related

Cisco WAN :: 1841 With 3G HWIC - Backup WAN Connection?

Jul 3, 2011

I'm trying to backup my primary WAN with secondary backup connection - 3G WAN through Cellular 0/0/0.Point  is that I need to track some external IP address on my primary  interface, for examle 8.8.8.8. If it is not reacheable, then router  brings up backup connection - 3G. This can be done by using  dialer-watcher.Simple.But unfortunately my primary WAN interface is an  FastEthernet, which is the coonected to a switch, switch to WAN . There  is no dialer-watch commands on it. Thats sad .

One more time :
 
WAN -> SWITCH -> ROUTER(WITH 3G HWIC and Fa 0/0 connected to switch).

View 4 Replies View Related

Cisco WAN :: 2951 / MPLS Branch Site Setup On T3 Line

May 24, 2013

setting up MPLS on a single T3 line. A client has contacted us to set up a 2951 at a branch location. There are 5 locations connected with MPLS.They will split off 4meg of the T3 for mpls. The rest of the 45meg would go to the internet.They have two 1841's currently set up with a T1 line in each. One 1841 connects to the MPLS and the other to the internet.When the T3 is turned up by the provider, everything, internet and MPLS, will go through it.  I asked for the current configurations, but I have not received them yet and this setup is due in a couple days.Given I've never configured MPLS before and I have a rudimentary understanding of how it works, any tips or configurations? I'd hate to be stuck on site and not equipped to complete the job.

View 3 Replies View Related

Cisco WAN :: Connect Four ADSL Lines To 1841 (Backup) And Work In Load Balancing Way

Dec 17, 2011

We have a cisco 1941 with line t1 Symmetric, (Also have Cisco 1841 unused, but works) I would like to connect the Cisco 1841 to four Adsl Backup lines in case the T1 or the Main cisco 1941 go down I know a BGP is needed on our ISP site,
 
How can i connect four Adsl lines to The cisco 1841 (Backup)  and make them work  in a Load Balancing way.

View 2 Replies View Related

Cisco Routers :: WAN / ISP Configuration - RV220w Versus 2951-SEC/K9

Sep 26, 2011

We are planning on testing a new ISP provider in our company but we have the following doubt: This new provider is using a Optical Fiber line (GPON – PT Prime) for this new internet connection and we already have a Cisco RV220W router but they are not sure if that can be used, so they just informed that they a capable router is the Cisco 2951-SEC/K9, that they are selling of course. So our actual doubt is if the Cisco 2951-SEC/K9 can have some “extra” WAN configurations/authentications that are not available in our Cisco RV220W and that can implicate that we cannot use our RV220w router?

View 3 Replies View Related

Cisco WAN :: 2951 - ROM Error Crashes Two Routers At The Same Time

Oct 30, 2012

We are a medium-large sized company with approx.100 offices located across North America. Every single office connects to each other and the data center via a DMVPN overlay network. The DMVPN hub router (Cisco 2951), R-Q9-1, is located at our data center and is the "workhorse" of the company. We also have a redundant hub router, R-Q9-2, at the data center with exact same hardware specs.
 
Each office builds an EIGRP Tunnel0 and Tunnel1 to R-Q9-1 and R-Q9-2 respectively. All data traffic flows over Tunnel0 to R-Q9-1 until it fails, at which point traffic starts to flow over Tunnel1 to R-Q9-2. This has been working seamlessly for last 1 year of implementing this design, until yesterday, when both R-Q9-1 and R-Q9-2 rebooted all of a sudden at the same time right in the middle of a production day. I confirmed there was no power failure at the data center. A show version of both routers gives me this:
 
R-Q9-1 uptime is 1 day, 1 hour, 24 minutes
System returned to ROM by address error at PC 0x5C92E28, address 0x5DF36FE9 at 11:52:23 EDT Tue Sep 21 2010
System image file is "flash0:c2951-universalk9-mz.SPA.150-1.M3.bin"
Last reload type: Normal Reload
[code]...
 
I Google that error but can't find anything specific other than it's saying it's some kind of bus error. What I also found a bit off is the time it's showing on both routers' show version output (Sep 21, 2010 and Jan 10, 2012). Here are the current clock settings on both routers at the time of this writing.
 
R-Q9-1#sh clock *16:53:31.216 EDT Wed Oct 31 2012 
R-Q9-2#sh clock *16:59:44.220 EDT Wed Oct 31 2012  
 
I checked my Syslog server and did not find anything specific during the time of the crash, however, syslog was filled with errors similar to this one
 
2469: * Tunnel0: NHRP Encap Error for Resolution Request , Reason: protocol generic error (7) on (Tunnel: 10.10.200.1 NBMA: IP address ommitted)
[code]...
 
I have never seen these errors before and all of a sudden they seem to have stopped since this morning.

View 4 Replies View Related

Cisco Routers :: RV220w / 2951 - VLAN ID On WAN Interface

Nov 10, 2011

We have a new optical fiber connection from a new ISP (only for Internet) and we found that our Cisco router RV220w won't work with this new connection because is not possible to add the V LAN ID 20 for the WAN traffic, as required by our ISP/connection. Now we would like to know what Cisco routers can support this feature and that can be "similar" to the RV220w or if there is another way to solve this problem and maintain our actual RV220w, because the features on this particular router (apart of the V LAN ID on Wan) are more than enough for us -

We would like to have a “simple” router and with firewall and VPN features as RV220w, because the one that our provider says that works seems to be too much for us Cisco 2951-SEC K9 – We are a small company with a network of around 10 computers and we only need some VPN connections for our sales companies in Europe and workers when traveling (3-5 VPN connections are OK).

View 3 Replies View Related

Cisco Switching/Routing :: How To Wipe 2000+ 2951 Routers

Sep 4, 2012

My  company is doing an nationwide upgrade of it's leased 2951 routers. For  security sake I need to wipe everyone of them before being sending them  back to the leasing company. I would like to somehow boot to a USB  drive and call it a day.

View 4 Replies View Related

Cisco VPN :: 2851 - How To Setup MPLS As Backup

Sep 4, 2011

I need a configuration example of MPLS with VPN as a backup Router cisco 2851

View 3 Replies View Related

Cisco Firewall :: ASA 5510 - ISP Backup Setup

Apr 5, 2011

I would like to setup backup ISP in our ASA5510.   Right now the the firewall has for default gateway following command:
 
"route outside 0.0.0.0 0.0.0.0 114.324.321.33 1"  i am changing this to route outside 0.0.0.0 0.0.0.0 114.324.321.33 10 track 1  ...so i can setup sla monitoring. As soon as i do the above command and remove the original "route outside 0.0.0.0 0.0.0.0 114.324.321.33 1" from asa then internet connection drops. Right now asa interface Ethernet0/0 has main isp configured and configuring  interface Ethernet0/3 as backup. interface Ethernet0/3 name if backup security-level 0 ip address 114.324.321.34 255.255.255.252 no shut global (backup) 1 interface.
 
route outside 0.0.0.0 0.0.0.0 114.324.321.33 10 track 1 ( Right now in firewall i have" route outside 0.0.0.0 0.0.0.0 114.324.321.33 1 " ) route backup 0.0.0.0 0.0.0.0  115.283.212.23 20 track 2
 
track 1 rtr 1 reach ability
track 2 rtr 2 reach ability

sla monitor 1type echo protocol ipIcmpEcho 114.324.321.33 interface outside sla monitor schedule 1 life forever start-time now sla monitor 2type echo protocol ip Icmp Echo 115.283.212.23 interface backup sla monitor schedule 2 life forever start-time now. Also our firewall has site to site vpn and 1 main ip configured for exchange and remote access. 

View 4 Replies View Related

Cisco Firewall :: ASA 5505 With Dual ISP - How To Setup Backup Connection

May 22, 2012

how can I setup that the backup connection will start but after 30s of icmp timeout the default gateway (tracket object - 192.168.1.1)
 
My configuration:
 
sla monitor 123
type echo protocol ipIcmpEcho 192.168.1.1 interface outside
num-packets 3
frequency 10
sla monitor schedule 123 life forever start-time now
 
route outside 0.0.0.0 0.0.0.0 192.168.1.1 1 track 1
route backup 0.0.0.0 0.0.0.0 192.168.2.1 254
 
track 1 rtr 123 reachability

View 2 Replies View Related

Cisco VPN :: 1841 - How To Setup IOS SSL VPN

Jan 25, 2013

i've been trying to setup an SSL VPN on my 1841 lab router but with no luck. i tried both clientless (anyconnect 2.5) and using a vpn client (anyconnect 3.0).
 
i'm using a win 7 PC with IP 172.16.1.50 directly connected to 1841 FE0/1 port. tried disabling PC FW, used both IE and FF and delete cookes but to no avail. below are my config and some show and debug output.

SSL_VPN_GW#show webvpn gateway
 
Gateway Name                       Admin  Operation
------------                       -----  ---------
SSL_VPN_GW                         up     up
 
SSL_VPN_GW#show webvpn context(code)

View 1 Replies View Related

Cisco WAN :: Setup VPN Server On 1841?

Oct 11, 2012

I have setup a VPN server on cisco 1841 and dialed through pc, it worked fine. But when I dial through another ISP it is not working. It can establish VPN but it can't pass traffic through VPN, what may be the problem. The configuration is same and I can access Internet through this ISP.

View 4 Replies View Related

Cisco 1841 - How To Login And Setup

Feb 17, 2011

Ok so i just got a 1841 and i have nfc where to start on hwo to set it up or make it work. How do i go about loging in to it so i can set it up to use it as a router? I tried to plug my pc in to the consle port and my pc doesn't even show i have any thing hooked up to it. so any step by step guides on how to log in and set this up?

View 19 Replies View Related

Cisco WAN :: Setup Client VPN Access On 1841 Router

Nov 23, 2012

Trying to setup client VPN access on a 1841 router. essentially i would like to connect using  the cisco vpn application.

View 2 Replies View Related

Cisco VPN :: Setup Remote Access In 1841 Router?

Aug 12, 2012

I am trying to set up Remote access vpn in 1841 router. The vPN client is connecting to router, but cannot ping to remote LAN Here is the config.
  
Current configuration : 3625 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption

[code]....
 
I am not getting any hit on the deny statement of 102 when i try pinging to client ip address (10.0.0.10).

View 2 Replies View Related

Cisco WAN :: 1841 / Getting Performance Based Routing Setup

Apr 27, 2011

Here is my setup:

Cisco 1841 Software (C1841-ADVIPSERVICESK9-M), Version 15.1(2)T1, RELEASE SOFTWARE (fc1)
 Cisco Internal IP:192.168.X.254
Cisco External IP 64.X.X.5 (NAT)
 Netopia DSL Router:
Internal IP: 192.168.X.253
Exernal: 76.X.45.3
 
Now the DSL was installed a while back for a different need and now that need is gone. What Id like to is have the Cisco router do performance routing and send out internet traffic to either its own external IP or send it over to the DSL if it can get a better response. Presently, Since the Cisco is my gateway, the DSL line is sitting idle.

View 1 Replies View Related

Cisco VPN :: 1841 / 881 - Setup A VPN To Connect To HO From Branch Office Through Router?

Jan 26, 2013

I have got two 1841 and one 881 cisco router. I can keep any one of this router at HO and remaining at branch office.  I have got a static internet IP at HO but dynamic IP at branch office. I want to setup a VPN to connect to HO from branch office through router. The branch connects through a private IP for internet purpose. Which VPN is the most secure and best for this purpose.

View 1 Replies View Related

Cisco Switching/Routing :: Setup Of Firewall In Between 1841 Router And Switch

May 26, 2013

We have a setup of a firewall in between my Cisco 1841 router and Switch.
 
Cisco Router --> Meraki Firewall--> Switch
 
Client VPN is configured on the Meraki Firewall but then for the outside users to client vpn in to the network, I have to port forward or open the ports 500 and 4500 to the IP address of the Meraki Firewall 192.168.1.90. [code]

View 4 Replies View Related

Cisco Routers :: RV082 Backup Vpn To C2851?

Feb 10, 2013

I'm planning to buy a few Cisco RV082's for remote offices and using them to connect to main office Cisco 2851 site to site vpn. So I guess, simple site to site vpn will work without much problem, but I wonder, will backup vpn feature work as expected on backup WAN channel and how should I configure it on the IOS side?

View 1 Replies View Related

Cisco Routers :: RV042 Not Working For Backup

Jun 21, 2012

Updated to newest firmware 4.2.1.02 and wanted to perform a backup of the startup configuration.  I get a "The webpage cannot be found" HTTP 400 error when trying to do this backup.  I have changed some settings since my last backup, but that backup was done using the last firmware revision.

View 3 Replies View Related

Cisco Routers :: QuickVPN Setup On RV120W Without Changing Internal Setup

Nov 8, 2011

Is there a way to set up Quick VPN on the RV120W without changing the internal subnet? I have just taken over responsibility for a network and I don't know all of the nooks and crannies yet, so I'd rather not change the internal sub net. I've tried setting up a user then changing the LAN settings afterward, but it automatically removed the VPN user when I did so.

View 1 Replies View Related

Cisco Routers :: SRP527W - Setup - Cannot Find Web Console To Setup

Jan 1, 2012

I've just purchased a couple of SRP527W routers. I've been unable to even browse to the default 192.168.15.1 to start my configuration. My local network is 192.168.1.x. At risk of showing my stupidity, what am I doing wrong.

View 5 Replies View Related

Cisco Routers :: RV042 Killing Off Site Backup After About 2 Hrs

Dec 23, 2011

I have 16 customers using RV042 router all 11 have the RV042 router different ISP's. After eleminating every thing else we were down to the routers. Two of the customers we built linux boxes to do the routing and firewalling and VPN, etc. Once in place the problems went away. Which confirmed it was the RV042 router causing the problem.
 
We watched the traffic and after about 2 hrs the router tells both ends to reset. End of communication.
 
My question is how do we stop the router from terminiating the connections. They are not bandwith hogs. They are nessessary connect connections. 

View 3 Replies View Related

Cisco Routers :: RV082 V3 VPN Tunnel Backup Not Available On RV016

Jun 1, 2011

VPN tunnel backup is not available on the RV016 firmware version 4.0.2.08 (it IS on the RV082. The data sheet and the manual for the RV016 is wrong. I have purchased several RV016 hardware V3 and several RV082 hardware V3. Both have the same current firmware version. We have noted that the RV016 does not have the VPN tunnel failover option found in the RV082. It also does not have split DNS (noted in the manual. A I would have thought that the firmware would provide equal options on the RV042, RV082, and RV016.

View 2 Replies View Related

Cisco Routers :: RVS4000 And NAT / Backup Internet Connection?

Apr 8, 2012

Just recently purchased an RVS4000 to take the place of an old NetGear FVS336, which supported multiple NAT translations. It appears that the RVS4000 does not support this, any other models in the small business line support this? I only need this for a backup Internet connection?

View 4 Replies View Related

Cisco Routers :: RV082 Backup File View?

Sep 19, 2012

Is there a way to view the contents of the .exp file generated from exporting the configuration from RV082? I've got a couple of RV082 that have the same rules, but want to compare the configuration. 

View 2 Replies View Related

Cisco Routers :: RVS4000 - Will Config Backup From V1 Restore To V2 Properly

Jun 3, 2012

I'm replacing an older (& failing) RVS4000 v1 with a new V2.  I need to minimize downtime.  Will a config backup from the old v1 restore properly to a new v2 (all have newest firmware)?  There are a lot of tweaks including several VPNs and to do it all manually is not desirable.

View 2 Replies View Related

Cisco Routers :: Moving From Faulty SRP527 To SRP 547 - Restore From Backup?

May 8, 2012

I'm trying to move from a faulty SRP527 to SRP 547 - I tried a Restore from Backup, but it doesn't work.So start from fresh, and I'm having an issue trying to add a 2nd SSID to a VLAN...
 
I keep getting the error:
 
"FAILED! SSID 2 has joined another VLAN"
 
Except it hasn't... its not assigned to any VLAN...

View 2 Replies View Related

Backup Account Creation For Routers Through KiwiCat Tool?

Sep 11, 2011

My backup userid, password, privi 15 on all our company routers Say around 300 routers, it is difficult to log in each router and create a backup account, i heard from one of my friend that i can create a backup account and can upload thru the kiwicat tool and it will automatically creates my backup account on all the routers. Procedure to create this.

View 6 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved