I have setup a VPN server on cisco 1841 and dialed through pc, it worked fine. But when I dial through another ISP it is not working. It can establish VPN but it can't pass traffic through VPN, what may be the problem. The configuration is same and I can access Internet through this ISP.
View 4 Repliesi've been trying to setup an SSL VPN on my 1841 lab router but with no luck. i tried both clientless (anyconnect 2.5) and using a vpn client (anyconnect 3.0).
i'm using a win 7 PC with IP 172.16.1.50 directly connected to 1841 FE0/1 port. tried disabling PC FW, used both IE and FF and delete cookes but to no avail. below are my config and some show and debug output.
SSL_VPN_GW#show webvpn gateway
Gateway Name Admin Operation
------------ ----- ---------
SSL_VPN_GW up up
SSL_VPN_GW#show webvpn context(code)
Ok so i just got a 1841 and i have nfc where to start on hwo to set it up or make it work. How do i go about loging in to it so i can set it up to use it as a router? I tried to plug my pc in to the consle port and my pc doesn't even show i have any thing hooked up to it. so any step by step guides on how to log in and set this up?
View 19 Replies View RelatedI am looking to setup a solution for backing up a Metro Ethernet connection on a 2951 using an 1841 and 2 T1's in a Multilink. The Metro E will be primary, and if the BGP peer goes down, I want it to switchover to the 1841. Can it be done and is there an example of the BGP setup to work off of?
View 1 Replies View RelatedTrying to setup client VPN access on a 1841 router. essentially i would like to connect using the cisco vpn application.
View 2 Replies View RelatedI am trying to set up Remote access vpn in 1841 router. The vPN client is connecting to router, but cannot ping to remote LAN Here is the config.
Current configuration : 3625 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[code]....
I am not getting any hit on the deny statement of 102 when i try pinging to client ip address (10.0.0.10).
Here is my setup:
Cisco 1841 Software (C1841-ADVIPSERVICESK9-M), Version 15.1(2)T1, RELEASE SOFTWARE (fc1)
Cisco Internal IP:192.168.X.254
Cisco External IP 64.X.X.5 (NAT)
Netopia DSL Router:
Internal IP: 192.168.X.253
Exernal: 76.X.45.3
Now the DSL was installed a while back for a different need and now that need is gone. What Id like to is have the Cisco router do performance routing and send out internet traffic to either its own external IP or send it over to the DSL if it can get a better response. Presently, Since the Cisco is my gateway, the DSL line is sitting idle.
I have got two 1841 and one 881 cisco router. I can keep any one of this router at HO and remaining at branch office. I have got a static internet IP at HO but dynamic IP at branch office. I want to setup a VPN to connect to HO from branch office through router. The branch connects through a private IP for internet purpose. Which VPN is the most secure and best for this purpose.
View 1 Replies View RelatedWe have a setup of a firewall in between my Cisco 1841 router and Switch.
Cisco Router --> Meraki Firewall--> Switch
Client VPN is configured on the Meraki Firewall but then for the outside users to client vpn in to the network, I have to port forward or open the ports 500 and 4500 to the IP address of the Meraki Firewall 192.168.1.90. [code]
I got 1 public IP for router and 16 Public IP's for NAT from ISP. Both router IP in one range and the NAT IP's are in different range. I want to use 1 NAT public IP for one of my windows server.Am using cisco 1841 router, in which I ve configured the public IP provided by the ISP for router.
View 10 Replies View RelatedI would like to set up a POTS Dial connection between 2 Cisco routers, using the modem card WIC-1AM-V2. I'd like to use this as an out-of-band connection to a remote site, if the primary internet connection fails. So, this setup will only be used in one direction, 1 router placing calls, the other one receiving calls.Here's my config of the receiving router:
chat-script dial "" ATZ AT OK "ATX3D T" ATS0=8 TIMEOUT 120 CONNECT C
interface Async0/2/0 description out of band for network no ip address encapsulation slip async mode interactive
line 0/2/0 session-timeout 5 absolute-timeout 10 script connection dial login local modem InOut transport input all escape-character BREAK autoselect ppp stopbits 1 speed 115200 flowcontrol hardware
[code]....
This config is working fine, when dialing in via a Windows Hyperterminal Dial connection. After a while of dialing I get the login prompt of the router.Now I want to have a router placing calls instead of a Windows Server. I can't figure out how to tell a router to place calls to a POTS phone number.
Receiving router: 2811, WIC-1AM-V2, IOS c2800nm-ipbasek9-mz.124-25a
Calling router: 1841, WIC-1AM-V2, IOS c1841-advsecurityk9-mz.124-25a
i've been using a VPN to connect to my home network from elsewhere for a few months. It's set up as follows:
PPTP
Maximum Strength Encryption
EAP-MSCHAP-v2 Authentication
Now I find out that MSCHAPv2 authentication has been broken and is no longer considered secure (even by Microsoft), so I want to change the protocol I'm using to make it secure.
However, I've spent 3 hours now researching this and I cannot for the life of me figure out how to use a better protocol on my Windows Server 2012 home server. I've tried setting up PEAP authentication (still PPTP) a la Microsoft's recommendation document, but it requires a certificate. I've created a self-signed certificate but it seems I can't issue certificates (via this method) without being a member of a domain, so I'm stuck. I can't even get started with L2TP since I can't find the option for it.
My question is this: Is there a way to setup a secure VPN server using Windows Server 2012 without a domain? If so, how do I do this?
I have configured Cisco 1841 router. My problem is what if every first time a user opens the browser will display a web page server. My web server ip address is 10.10.1.5. [code]
View 4 Replies View RelatedI am deploying a Cisco 1841 in place of our basic DSL router.I have an ADSL WIC and FA0/0 connected to our LAN.LAN IP ADDRESS range is 192.168.1. 0/ 24 I have dynamic and static NAT configured. At this point although I have ACL's configured I have NOT implemented them as yet for the following reason. I am unable to recieve inbound SMTP traffic - now know my MX records are correct as this all owrks happily on our basic DSL router. I can send external emails no problem and all internal email works fine. [code] I am in the process of defaulting the router and programming the barbones to get the link working and see if inbound SMTP works then start building the blocks again.
View 4 Replies View RelatedI have a 1841 deployed as my NAT device towards internet. NAT is setup so that internal addresses can access WWW. I also have some NAT translations opening speciic ports from outside to inside in the form: ip nat inside source static tcp A.B.C.D 443 A.B.C.D 443 extendable.
Now have an outside address/port setup with a public DNS reference and using NAT from outside to get access to the corresponding inside address. It works when being outside the LAN.
Now to the problem: From the LAN side of the router - i cannot access the public name. I can ping it - but my browser dont find the webserver behind the name. Someone told me it should be setup as "local firewall domain" - and i should set this up as "source NAT".
Our company has a Cisco 1841 router which provides our connection to the outside world. We also have a windows server which provides our DHCP and DNS services. Our workstations which also get their lease from the server (using DHCP) do have a connection to the outside world.
when we connect a new computer or other device to the network we can only ping as far as the inside interface of the router. But when we assign the ip settings staticly we do get a connection, even if we configure it with the exact same ip as a lease it got a few seconds ago.
[code]...
We have 2mbps leased line and have Cisco 1841 which is managed by our ISP. I have hooked up another 1841 (please find basic config below, it will get more complex lateron) Now when I connect my laptop I am able to browse Internet. But when I conect VOIP phone, it is not able to contact it's Hosted Server on Internet.
VOIP phone is Polycom SoundPoint 550 and I get URL call disabed message. If I try netgear Firewall everything seems to work.that the voip provider needs following ports UDP Range 16384 - 32766, TCP 5060 & UDP 5060. But in my config all outbound traffic is allowed. [code]
I am using Solawinds syslog and trying to get our Cisco routers send syslogs to our syslog server. I followed the procedure on Configuring Cisco Devices to Use a Syslog Server from [URL] Our Cisco swtches are all sending syslog messages but not the routers. I compared the config with our access switches but can't seem to find the problem:
Sample router config:
service nagleno service padservice tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msec localtime show-timezoneservice timestamps log datetime msec localtime show-timezoneservice password-encryption!hostname WWF-RT1boot-start-markerboot-end-marker!security authentication failure rate 10 logsecurity passwords min-length 8logging buffered 4096logging rate-limit all 10logging console critical!aaa new-model!!
[Code] .......
is there a command that prevents the router from sending the syslog to the server?
I've setup a NTP service by using Cisco 2811 routers. This works fine at the moment, but in the end there are some questions left.
1. I'm using two 2811 Routers, one for primary, which is resceiving the time from PUBLIC NTP 1, and one for backup, which is resceiving the time from PUBLIC NTP 2. Is it possible to compare these to times an check if the match? And if not, generate an alarm via e.g. SNMP
2. Is it possible to check via SNMP, if the routers are reaching PUBLIC NTP 1 and PUBLIC NTP 2 for sync?
ASA 5505 Sec plus lic w/OS 9.1
I want to setup a quick and simple VPN server on my ASA. I want to do local authentication and, once authenticated, I want to allow all internal access. I only have 1 WAN IP. I'm finding a ton of conflicting info online. The ASA is already setup and is operational. I just need the correct commands to setup the VPN.
I am trying to setup syslog server on LMS 4.0.Everything seems to be working fine but I have a lot of stragne logs in my syslog.log file.Every single day I receive logs like :
Mar 05 09:31:03 127.0.0.1 100: <30> dmgt[1136]: 3007(I):Started application(1015) "e:CSCOpxincwjava.exe -cw:jre lib/jre -cp e:CSCOpxMDC omcatsharedlibMICE.jar;e:CSCOpxMDC omcatsharedlibNATIVE.jar;e:CSCOpxMDC omcatsharedlibjdom.jar;e:CSCOpxMDC omcatsharedlibxalan.jar;e:CSCOpxMDC omcatsharedlibxerces.jar;e:CSCOpxMDC omcatcommonlibservlet.jar;e:CSCOpxMDC omcatsharedlibcastor-0.9.5.jar;e:CSCOpxMDC omcatsharedlibcastor-0.9.5-xml.jar;e:CSCOpxlibclasspath;e:CSCOpxwwwclasspath;wwwclasspathvbjorb.jar;MDC omcatwebappsupmWEB-INFclasses;libjrelibendorsedjacorb.jar;MDC omcatwebappsupmWEB-INFlibctm.jar;MDC omcatwebappsupmWEB-INFliblog4j.jar;MDC omcatwebappsupmWEB-INFlibjep-3.2.0.jar;MDC omcatwebappsupmWEB-
[code]....
I dont want to get any logs from 127.0.0.1. Is it possible to filter out logs from server ?
I am trying to configure a Cisco 871 to act as a PPTP VPN server on my home network. I have referenced Cisco's documentation regarding this which I will include below as well as a copy of my current running configuration and terminal monitor information from when I attempt to establish a connection.
When I attempt to connect from a Windows machine I receive the following error: 'Error 807: The network connection between your computer and the VPN server was interrupted.' 'The remote device won't accept the connection.'When I attempt to connect VIA my mobile, I get 'The server has hung up'.The 871 does detect the incoming connection which can be seen from the terminal monitor output: url...
How would I set up my own anonymous proxy server with my own ip address without having to go on a proxy list site? I don't care how complicated or time consuming it may be, I'm a very fast learner and I do things extremely quickly.
View 3 Replies View RelatedI host a minecraft server for my friends, but I always have to give them my ip every time because my ip changes everyday, and that is really annoying.
View 11 Replies View Relatedi need a guide to set up a server network.
View 1 Replies View RelatedI setup one acs v5.3 in one server in NYC and another acs v5.3 in SJC.I want to make the acs.nyc as primary and acs.sjc as the secondary, how do i setup it up?
View 1 Replies View RelatedI need to setup a syslog server for PIX w/ 6.2 and was hoping to get detailed instruction how to go about it. I would like exact syntax w/ an example on the pix and any configuration on the computer that will be receiving the log info. I have downloaded tftpd32 onto computer
View 1 Replies View Relatedwe are having some trouble setting up our router (Cisco 861W) webserver on the LAN so that it can be accessed from outside (http via port 80). When we try to access it via the web address, we just get the login window of the Cisco router software?
View 10 Replies View RelatedI've made hotspot ad hoc and then my client try to connect my hotspot but it must setting manually...how to my client connect to my hotspot automatically not manually??? and how to install and setup dhcp server i windows 7...
View 6 Replies View Relatedshow me the necessary steps and a type of hardware/software to buy to setup a network storage server that allows me and my family to access/share all files from anywhere thru the internet?
View 5 Replies View RelatedAbout my internet setup, I receive internet from my ISP via the LAN cable. The IP is static, provided by the ISP. To use the internet, I have to login to their server using a username and password.Earlier, I did not have a router. So, to see if the ISP server was up, I could just ping the IP of the ISP server from my computer using the command prompt, and it would show whether it was up.However, since I got a router, I find that I cannot ping the ISP server from the computer directly as before. To ping the ISP server, I have to open the router administration page using the browser, then use its diagnostics feature to ping the ISP server. It shows only a few pings, and is not like the continuous ping that can be seen when you run ping from the command prompt. So, it's difficult to see the pings, and also diagnose. Also, sometimes the router pages do not open and get stuck, even after being refreshed.Is there any way, or any setting, by which I can ping the ISP server from the command prompt on the computer? Do I have to make changes in firewall settings of computer, or any settings in the router?Why can't I ping the ISP server directly from the computer?I am using Windows 8. The firewall of Windows 8 is on, and the hardware firewall on the router is off.
View 9 Replies View Relatedi want to setup DHCP using my windows xp
View 1 Replies View RelatedHow i should setup my network to include a DNS Server. I have 2008R2 running on a VM on my main desktop machine (this will soon be moved to a dedicated VM Server) with my Virgin Superhub acting as the primary router / modem. I also have a Belkin N+ router in AP mode and a dedicated AP for wireless around the home.I have a few options on how to configure the network adaptor for the VM Server. [code] On my host machine i have the two default VM Network adaptors for "Host only" and "NAT".Im not really sure on how the IPv4 should be configured on these adaptors in order than the VM server is on the same network as my physical machine without conflicting IP's. If i leave it default the VM server gets a default IP of 192.168.13.138.
View 1 Replies View Related