Cisco Switching/Routing :: 1841 - No Connection Through Gateway With Windows Server?
Aug 26, 2012
Our company has a Cisco 1841 router which provides our connection to the outside world. We also have a windows server which provides our DHCP and DNS services. Our workstations which also get their lease from the server (using DHCP) do have a connection to the outside world.
when we connect a new computer or other device to the network we can only ping as far as the inside interface of the router. But when we assign the ip settings staticly we do get a connection, even if we configure it with the exact same ip as a lease it got a few seconds ago.
[code]...
View 21 Replies
ADVERTISEMENT
Feb 12, 2012
I'm trying to configure an IPSEC VPN + tunnel for multicast data. When the default gateway is set on the router (1841) it works fine but if I only set a route to the IPSEC peer via our gateway then the tunnel fails to come up. The end point is to a 3rd party. [code]
I found that if I add a static route for the tunnel destination via fa0/0, the public facing interface, the tunnel comes up..ip route 10.23.4.2 255. 255. 255. 255 FastEthernet0/0
and I can then ping the tunnel IP at the far end - 10.23.0.5.Why would that be? Is there a better way to do this without using a default route??
View 4 Replies
View Related
May 30, 2012
I am just setting up a simple scenario with a 1841. Server @ 172.31.1.1 cannot ping 172.31.0.254 or 172.31.0.105. It can ping 172.31.1.250. The router can, on the other hand, ping devices on both networks. This is just for testing routing theory so I don't know why hosts on either side of the network cannot ping each other.
I am only using the FastEthernet interfaces on Router 1841.
View 3 Replies
View Related
Jan 22, 2012
I have a 1841 deployed as my NAT device towards internet. NAT is setup so that internal addresses can access WWW. I also have some NAT translations opening speciic ports from outside to inside in the form: ip nat inside source static tcp A.B.C.D 443 A.B.C.D 443 extendable.
Now have an outside address/port setup with a public DNS reference and using NAT from outside to get access to the corresponding inside address. It works when being outside the LAN.
Now to the problem: From the LAN side of the router - i cannot access the public name. I can ping it - but my browser dont find the webserver behind the name. Someone told me it should be setup as "local firewall domain" - and i should set this up as "source NAT".
View 12 Replies
View Related
Dec 15, 2012
I am using Solawinds syslog and trying to get our Cisco routers send syslogs to our syslog server. I followed the procedure on Configuring Cisco Devices to Use a Syslog Server from [URL] Our Cisco swtches are all sending syslog messages but not the routers. I compared the config with our access switches but can't seem to find the problem:
Sample router config:
service nagleno service padservice tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msec localtime show-timezoneservice timestamps log datetime msec localtime show-timezoneservice password-encryption!hostname WWF-RT1boot-start-markerboot-end-marker!security authentication failure rate 10 logsecurity passwords min-length 8logging buffered 4096logging rate-limit all 10logging console critical!aaa new-model!!
[Code] .......
is there a command that prevents the router from sending the syslog to the server?
View 2 Replies
View Related
Apr 9, 2013
I tried to connect a 1841 to a Linksys with a static route. I am able to ping from a computer in the 1841 to a computer in the linksys network, but I can't ping from a computer in the Linksys network to a computer in the 1841 network?
View 7 Replies
View Related
Apr 26, 2013
I am looking to add remote sites that will authenticate with the Windows Server using VPN via Cisco rv042 routers in a gateway to gateway setup.My main concern is the placement of the server to the router and what would be considered best practice.In my mind, option 1 seems to be what I want - however, this would mean disconnecting the WAN feed to the server (my ip is static and tied into the MAC address of the server). While option 2 doesn't look right to me, it would leave the existing configurations in place which would minimize my downtime (I think)
View 10 Replies
View Related
May 14, 2012
I am trying to learn more about networking and system administration. I am practicing allot on VMs i am running here at home. I am not sure if it is allow to ask beginners questions on this site but i will try my luck anyway.
View 2 Replies
View Related
Oct 18, 2012
I have a server (Windows Server 2003) that randomly looses connection with the default gateway and anything on the outside. When this happens, the server cant ping the gateway (A Juniper SSG5 firewall/router) and the gateway cant ping the server. But the server still can ping anything else on the network and everything inside the network works fine with it. The most reliable remedy is to reboot the router. Rebooting the server or resetting the network card sometimes works. I have tried both onboard network cards and a separate PCI network card on the server. There are no router log entries that correspond to the problem. This server is used as a Terminal Server for a remote office and as a file server.
View 1 Replies
View Related
Mar 27, 2012
I have trouble with a Cisco 892 Router from my Internet service provider.
Last week we switched from a virtual Router to a hardware Router. But after plugging it in our LAN Switch, the Windows DHCP Server stopped leasing IP's. I got many BAD_ADDRESS with MAC like e1:80:10:ac, e2:80:10:ac, e3:80:10:ac, e4:80:10:ac, e5:80:10:ac, ea:80:10:ac, eb:80:10:ac, ec:80:10:ac and so on.
I do not have access to the Router config, so I can not dump the config to you. We have a flat LAN, single SUB-Net(172.16.0.0/16) and no VLAN, no Spanning Tree. A Keep it Simple, Stupid(KISS) System.
A tech guy from service provider, is telling us, the error is not there fault and my switch is not correctly configured. But this is ********. For years we had a another Cisco Router from the precursor ISP and for 2 years the virtual Router from our current ISP. No trouble with my DHCP. But after plugging the new Router in, my DHCP stopped working.On the 892 is no running DHCP, but something interferences with my Windows Server 2008 R2 SP1 DHCP Server.
View 15 Replies
View Related
Aug 28, 2011
I can connect to the internet via wireless just fine, and everything will be hunky-dory for a while. After a while, however (this varies anywhere from a day to a week), there will be a small hiccup on the connection, and then something fails in the Acquiring Network Address stage. My computers will get an IP, but they will not get the default gateway or DNS server.I have tried a plethora of fixes, from simple computer reboots to fiddling with all sorts of settings, and nothing works to reestablish the connection. My father has also tried fixing it, to no avail. I have to go and reset my router, which also interrupts TV service, because it is through AT&T U-Verse. Needless to say, this does not make other people in the household very happy, and I really shouldn't have to be resetting my router every couple of days like that. My PC uses a Netgear WG111v3 adapter and is Windows XP. My laptop has on-board Wifi and is Windows XP Professional.
View 2 Replies
View Related
Oct 2, 2012
Is there a way to configure a DHCP server for my internal subnet of 192.168.20.1 which is on a 3550 layer 3 switch from my 5505 ASA Firewall.My subnet of 10.1.1.0/30 is connecting my 5505 to 3550. All I'm trying to do is run a DHCP server down to my hosts. The only options on ASA 5505 is
dhcpd address 192.168.20.1 - 192.168.20.254 outside or inside, which conflicts with my subnet of 10.1.1.0 used to connect my internal subnet of 192.168.20.1 for the whole network.
When I used my router it did not need the (inside, outside) keywords and just an ip helper-address command. How do I configure my my firewall DHCP server to propagate the 192.168.20.0 network through my 10.1.1.0 connection.
View 3 Replies
View Related
Feb 1, 2011
I've recently installed a new WRT610N router onto my small business network. Previously my network was as follows: Modem - Server - LAN where the server acts as a gateway using routing and remote access.
The addition to the setup now has the router between the modem and the server itself. After configuring everything - and DISABLING the router firewall and as last resort opening the server to the DMZ i'm having serious issues opening specific ports but not others.
To be specific - the server is sitting in the DMZ open right now. In my routing and remote access any port that I have being forwarded over to another computer is open from the internet with no issues. The problem lies with ports that need to be opened on the server itself with 127.0.0.1 where i'm getting a "connection timed out" from canyouseeme.org.
Why the local opening of ports is having issue? Before the router was installed everything worked great - however the router is needed for wifi and it cannot be configured as an access point only.
View 3 Replies
View Related
Jan 2, 2012
I have an issue with a Cisco 4900M switch with a WS-X4908-10G-RJ45 half card. The link connection between a 10Gbase-T server nic and the switch does not establish, i believe it is an auto negotiation problem. The link fluctuates constantly between connected and disconnected when set to auto negotiate. When the 10G half card port groups are configured for 1G connections it does the same. If i hard code the server nic to 1G the link remains up when the port group is at 1G. If i hard code the server nic to 10G the link stay down, i don't think the port speed and duplex can be hard coded on the switch end. I have tried updating the drivers on the server as well as diagnostic tests on the nic, which passed. The 4900M IOS code is version 15.0.2-SG2. If i plug a laptop into the 1G configured port the switch and the laptop negotiate at 1G. Also, i believe, if the 10G server nic is plugged into another 1G only switch the link auto negotiates to 1G as normal. The server nic is an INTEL Server Adapter AT 10G, which became end of life in 2009. I believe the half card came out in 2010.
View 5 Replies
View Related
Nov 16, 2011
I have a 3845 router. Setup SSH Version 2generated rsa keys (1024)set login localtransport input ssh and telnet is enabled since I can't get ssh connection working When I connect using SSH, I get the following error. server refused authentication protocol.
View 21 Replies
View Related
Sep 20, 2012
I have a question regarding fabric storage and cisco catalyst switch 3650.My plan is connecta a esxi server to a nexus switch and then to a san storage. I want add a new switch to have a redundant link between esxi and the storage.Can I use a cisco catalyst 3650 with a fiber conecction to connect the HBA esxi server card to 3650 sw and the SAN storage to the 3650 sw ?
View 2 Replies
View Related
Feb 6, 2012
I'm just getting started with cisco kit so you will have to bare with me.I have a cisco 1841.i have a very wierd issue of routing...i cannot ping and browse through this.
View 3 Replies
View Related
May 31, 2013
I have a problem accessing my wireless router through VLAN sub-interface on my Cisco 1841 router. My hardware:
Cisco Catalyst 2960 switch (192.168.100.4 /24)
Cisco Catalyst 3550 switch (192.168.100.6 /24)
Cisco 1841 router (192.168.100.7 /24)
Asus RT N66U wireless router (192.168.100.2 /24)
Here's my network topology:
I have two VLANs - 10 and 20. 2 DHCP pools are configured on 2 1841's interfaces - 192.168.1.0 /25 and 192.168.1.128/26 with default router sitting on 192.168.1.1 and 192.168.1.129 respectively. No issues with obtaining IP address from any of those pools.Laptop connects to L3 3550 switch (switchport access vlan 10), which, in turn, connects to 1841 router through trunk (with VLANs 10 and 20 allowed).3550 is connected to 2960 through trunk with VLANs 10 and 20 allowed.Wireless router is connected to 2960.I can successfully ping my wireless router and outside world from 1841 from fa0/1 interface, but not from fa0/1.10 or fa0/1.20 sub-interfaces - all packets got dropped. My laptop can obtain IP from both pools (depending on port I connect it to), but can't ping my wireless router and anything beyond it.
I attach my configs:Cisco Catalyst 3550:interface FastEthernet0/1 switchport trunk encapsulation dot1q switchport mode trunk switchport port-security mac-address sticky speed 100!interface FastEthernet0/2 switchport trunk encapsulation dot1q switchport mode trunk!interface FastEthernet0/3 switchport access vlan 10 switchport mode access!interface FastEthernet0/4 switchport access vlan 20 switchport mode access!Cisco 1841:
ip dhcp pool Vlan10DHCP network 192.168.1.0 255.255.255.128 default-router 192.168.1.1 dns-server 208.67.220.220 domain-name home.local
!ip dhcp pool Vlan20DHCP network 192.168.1.128 255.255.255.192 default-router 192.168.1.129 dns-server 208.67.220.220 lease 0 12
interface FastEthernet0/1 ip address 192.168.100.7 255.255.255.0 duplex auto speed auto!interface FastEthernet0/1.10 description VLAN10 Sub Interface encapsulation dot1Q 10 ip address 192.168.1.1 255.255.255.128!interface FastEthernet0/1.20 description VLAN20 Sub Interface encapsulation dot1Q 20 ip address 192.168.1.129 255.255.255.192!
Routing table on 1841:
[code]....
View 19 Replies
View Related
Feb 8, 2011
we do have 2 Rv042, one in my office and one in my house.. in the office we do have static ip and at home none.. question is can i connect the two RV042?
View 1 Replies
View Related
Mar 22, 2011
I have some problems in my network with Gateway to Gateway Vpn Connection using two Rv042 routers.
I cannot ping the computers with static ip configuration.
In local an remote computers who have DHCP ip configuration i can ping each other .
View 1 Replies
View Related
Nov 12, 2012
We have two Cisco 3560E layer 3 switches at the core of our network. The switches are configured as an HSRP pair and the clients on our network point to the HSRP address as their default gateway. So if CORE-A dies, then CORE-B will pick up the address and the default route for the clients will continue to be available.We also need to specify a few static routes on the core switch to allow us to get to specific networks. Is there a way to do this so that the routes failover in the same way that the default gateway does?
View 2 Replies
View Related
Feb 26, 2012
If client gateway = 192.168.64.9 then next-hop = 192.168.64.8 else use default-route 0.0.0.0
I know it's possible to do a route-map match ip-address ACL list. But is it possible to match on gateway?
Some info about hardware and config:
6509-E in VSS (IOS 12.2(17r)SX5) withVS-S720-10G supervisor.
All routes are static, IP for 192.168.64.9 is on SVI vlan.
View 3 Replies
View Related
Mar 6, 2012
I have two ISPs. Each is on it's own subnet connected to the 6509 MSFC/Switch. FW1 is on 100.1.100.0/30 and FW2 is on 200.1.200.0/30 subnet. My goal is route all traffice going to the Internet from subnet 10.133.3.0/24 to FW1 and all other subnets across the organization to FW2. I am not sure if I need to use ACL / Static route combo, or just a static routes or ACLS?
View 5 Replies
View Related
Mar 11, 2012
I'm running into what seems a basic ip routing config problem with a Catalyst 3750 (IP Base) switch. I have several VLANS configured on the switch with IP routing enabled, and the switch is connected to the inside interace of a new ASA 5520 as follows:
ASA5520 IP (Default gateway): 192.168.1.1Switchport Gi1/0/1 is configured as a routed port, IP address 192.168.1.3 255.255.255.0Example VLAN is VLAN 100, IP address 192.168.100.1 255.255.252.0 From the switch CLI, I can ping all VLAN addresses, as well as the ASA5520, and the client laptop I'm testing with from VLAN 100.
From the client laptop on VLAN 100, I can ping all switch interface and VLAN addresses (inter-VLAN routing is working), including 192.168.1.3, but I CANNOT ping the default gateway at 192.168.1.1.
Here is the relevant configuration information on the 3750:
!
no aaa new-model
switch 1 provision ws-c3750x-24
system mtu routing 1500
[Code]....
View 4 Replies
View Related
Feb 25, 2013
We have two catalyst 3560 switches running c3560-ipbasek9-mz.122-58.SE2.bin They are connected using etherchannel using gi 0/21 - 24 interfaces.
on 3560-1 switch, there isn't any ip-default gateway or ip route configured. It only have 1 interface vlan configured.
on 3560-2 switch, there is ip default gateway configured along with 1 interface vlan.
What i dont understand here is that, i can reach out to other subnets from 3560-1 switch in which the routing is not enabled?
View 4 Replies
View Related
Sep 2, 2012
I have a Cisco 1841 router at home with version 12.4(13r)T advanced ip services. The setup is extremely simple:
1) PPPOE dialer to my service provider over ADSL
2) Nat overload on the dialer interface.
3) 2 V LAN s one for home network (wired) and one for wireless both v LAN's are connected through interface v LAN s respectively.
My problem is when I configure static NAT to map RDP or any other protocol to inside hosts this does n`t work.
"
ip nat source static tcp 192.168.20.3 2222 interface Dialer1 2222
ip nat source static tcp 192.168.20.3 3389 xx.xx.xx.xx 3389 extendable
ip nat inside source list 20 interface Dialer1 overload
"
When I open wire shark and sniff the traffic on home computer which is the one I`m trying to reach I can't see any traffic. And While performing Nat debugging I am also not able to see traffic going to that port (for example 3389).
View 7 Replies
View Related
Nov 16, 2011
I've got an 1841 router and am using NAT to expose certain IPs and ports to the outside world so that external users can see internal resources (namely, web sites). However, I can't seem to get it running such that I can visit the external IP address from inside the network and get the router to turn the request around so that it is redirected back inside the network. Shouldn't this be possible? Our previous router (a non-Cisco) was able to do this, but I can't seem to get the new one to do it.
A couple of key config lines:
interface FastEthernet0/0
ip address a.b.c.178 255.255.255.240
[Code].....
View 1 Replies
View Related
Jan 5, 2013
I guess i am just getting old and forgot how this works, or i have an IOS load with an undocumented feature in it.A customer of ours wishes to have their exchange server appear to the outside world on a seperate IP address as their public pool address is.in the past this has not been an issue, however in the current configuration we are unable to get the source address to appear per the NAT statement it always sources on the overloaded IP. below is the relevant NAT config, am i missing something, or have i hit a IOS feature? [code] There is a 45% chance i have forgotten everything i learned on the NOC desk and a 50% chance that it is somethine really stupid and 5% IOS is broken
View 5 Replies
View Related
May 2, 2012
I want to SSH into a Cisco 1841 router and depending on the suffix added to the SSH (i.e ssh myrouter.myroute.com 2002), would like it to forward this request to a terminal server.Can this be done? If so, how does one accomplish this? I have done something similar with RDP but I was not sure about SSH.
View 3 Replies
View Related
Oct 28, 2012
What is the command to shutdown a cisco 1841 (say, to add a module)? I know how to reload / reboot, but does not seem to find any command with an obvious name.
View 1 Replies
View Related
Jan 19, 2013
I have an 1841 running Advanced Enterprise Services 12.4(22)T3 that is functioning as a DHCP server and DNS server. What I am trying to figure out how to do is have the DNS service respond to queries about the clients of the dhcp service. I have successfully enabled it as a caching server for other requests, like "google.com" and "cisco.com", but what about the hosts on the local LAN?
As an example, let's say a Windows computer connects to the network with the hostname "computer" and receives an IP address from the 1841 with the domain name "test.net". I would like the 1841 to serve DNS queries for "computer.test.net" with the IP address that it assigned.
View 7 Replies
View Related
Mar 7, 2012
We have a Cisco 1841 router that requires 2 levels of access, at the moment we have network admins logging in with a single username via SSH and with privilege 15 but we also need our helpdesk to login to run certain commands but not chaneg anything
View 4 Replies
View Related
Jan 3, 2013
we've to configure our router 1841 to use both 2 interface Fe for two different vlan (also the second has to go on internet).
Actually we have int Fe0/0 configured with an ip address 192.168.1.1 for lan1 192.168.1.0/24 and we will use the second int Fe0/1 with another ip address like 192.168.2.1 for lan2 192.168.2.0/24.
see below configuration:
[code]...
View 5 Replies
View Related
