Cisco Routers :: RV042 1 To 1 NAT Stopped Working
Jan 6, 2012
I've had 1 to 1 NAT setup for years now with no issues and the other day it simply stopped working. Rebooted everything, had ISP clear arp on their cable modem yet nothing going. As soon as I remove the 1 to 1 NAT on the router the PC has internet access. Add the 1 to 1 back and no out going internet. The configuration is pretty basic and has not changed.Thinking it could be a hardware issue I swapped it out with another RV042 I have with the exact config, same thing 1 to 1 NATs have no internet access. Upgraded one of the RV042 firmware to Firmware Version: 1.3.13.02-tm, had cable modem replaced, spent numerous calls with ISP. nada
I have found one interesting thing however, any internal machine which is set to dhp works fine, and static ip that does not have a 1 to 1 nat works fine and the last ip in the 1 to 1 nat range works fine. If I extend the range it is always only the last ip that works. Even if I add 1 to 1 nats one line at a time, it is always the last entry that works..
View 4 Replies
ADVERTISEMENT
May 16, 2012
My organization has deployed 3 Cisco RV042 (v3) at our 3 sites. They have been working pretty well up until about a week ago. One of them continues to route traffic and perform port-forwarding, but the VPN has completely stopped working and I can no longer access the web administration interface. I get the standard login page, but any attempt to login (with correct or incorrect password) takes maybe 5 minutes with a spinning status icon, followed by a blank page leaving the browser at: url...
I have the router logs e-mailed to me, and I can see that the system boots up with Jan 1 2010 as the system date, but it eventually gets the correct date from NTP, so I'm doubting this is causing the problem.
These were working for months prior to this happening, and even a reboot of the affected RV042 does not allow me to log into it or setup the VPN tunnels. I have found similar threads on this forum: url...
View 2 Replies
View Related
Sep 30, 2012
I have a 6 month old RV042 with the newest firmware (v4.2.1.02). Over the weekend I configured the DMZ which after a lot of trial and error, was able to get working. Prior to configuring DMZ, I was able to log in with remote management. However now remote management no longer works. I've tried:
- Rebooting the router
- Turning the firewall off/on
- Turning remote management off/on
- Changing the remote management port
The only step I haven't taken is resetting the router back to factory defaults and trying to reconfigure it all again. This router is so finicky I have no faith I'd be able to get my current functionality back again.
View 2 Replies
View Related
Mar 1, 2013
I have the router for over two years, Present Firmware is V2.0.1.3, I have Polycom phone connected to the router using 8 x 8 VOIP service. The phone was working fine untill yesterday. 8 x 8 tech support suggested getting a different router. I have the same router at home and tried the same phone on my home router - it worked. So, the problem is not the phone but int he router. I tried to call Cisco tech support but found out that the warranty support expired and I need to buy a support plan. Called to buy the support, and gave up after an hours on hold. Left message.
View 1 Replies
View Related
Dec 20, 2010
My Linksys WRP400 router has stopped working. power led blinks red and orange - phone led 1 and 2 light green - wifi connection not work - ethernet LAN connection not work - ethernet WAN connection not work - router now work in bridge mode - factory reset using Reset switch not work - connected analogue phone not work I try dump traffic using ngrep on LAN and WAN port but no packet comes from the router.
View 2 Replies
View Related
Dec 8, 2011
I tried to configure two RV042 working together. [code] WAN2 of both Router1 and Router2 are unused (unplugged). However, the Host2 can never ping to Host1. So as to Host1. Should I need to configure the protocol binding for all the traffic to the WAN1?
View 3 Replies
View Related
Oct 21, 2011
So have a RV042 VPN router that is directly connected to the ethernet port of our comcast cable modem.
If I connect to it using QuickVPN (1.4.2.1) from a PC that is connected using AT&T 3G Network it works fine!
If I connect to it using QuickVPN (1.4.2.1) from a different PC that is connected using home WiFi (linksys wrtxxx) then it fails. In the VPN log all I see is failure messages for ping.
2011/10/22 15:47:28 [WARNING]Failed to ping remote VPN Router!
If I open a regular command prompt and attempt to ping the VPN router it works so not understanding why the QuickVPN is unable to ping.
how I can troubleshoot this further. Makes me think the RV042 config is fine otherwise it would not work on a 3G connection. Something on the home PC or the home network. Not sure what to check.
View 2 Replies
View Related
Jun 21, 2012
Updated to newest firmware 4.2.1.02 and wanted to perform a backup of the startup configuration. I get a "The webpage cannot be found" HTTP 400 error when trying to do this backup. I have changed some settings since my last backup, but that backup was done using the last firmware revision.
View 3 Replies
View Related
Apr 16, 2012
I have set up an RV042 v1 and v3 both in Load Balancing mode. Set in Router mode.I want one of the WAN ports to be preferred so I added a static route to 0.0.0.0 metric 5 to that WAN.Sometimes the route shows in the routing table and sometimes it goes away!!
View 2 Replies
View Related
Apr 1, 2012
When my RV042 is accessed for long transmissions (svn check out, usually after 20 minutes ) the client receives a message "Gateway not responding, do you want to wait".
When this happens I see the following in the RV042 system log (the first 3 lines of the log below are normal):
Apr 2 17:36:53 2012Connection AcceptedTCP 192.168.2.2:8888->192.168.1.5:50046 on ppp1Apr 2 17:36:54 2012Connection AcceptedTCP 192.168.2.2:8888->192.168.1.5:50046 on ppp1Apr 2 17:36:54 2012Connection
[Code]....
View 10 Replies
View Related
Aug 12, 2011
We bought an RV042 at the end of June. It is used as a gateway and VPN router. DHCP server is disabled and all IPs are configured manually.Every once in a while (Tuesday night, then Friday night - yesterday, it has hapened once or twice before that) the router appears to restart (see log below) then comes back up with system time of Jan 01 2010. At this point the router will no longer load its configuration page (https://10.29.238.197:16443/) and VPN connection to our customer in Africa drops. However, devices behind the router can be reached and can access the internet. The only way to fix this is to power cycle the router at which point everything starts working flawlessly again.The PID VID is RV042 V03 running firmware v4.0.3.03-tm (May 12 2011 21:27:37). Our RV042 is a newer one with Cisco SMB Router branding not the older Linksys branding.
From the log when the router reboots:
Aug 12 22:38:42 2011VPN Log(g2gips0) #141: retransmitting in response to duplicate packet; already STATE_QUICK_I2Jan 1 01:00:05 2010System Logheart : System is upJan 1 01:00:13 2010System LogWAN connection is up : 10.29.238.197/255.255.255.192 gw 10.29.238.225 on eth1Jan 1 01:00:15 2010VPN Log(g2gips0) #1: [Tunnel Negotiation Info] >>> Initiator Send Main Mode 1st packet
I looked at the log more and all the usual messages assosciated with VPN being established are there - the last thing in the log before the router coming back up again is:
Jan 1 01:03:49 2010VPN Log(g2gips0) #4: [Tunnel Negotiation Info] Quick Mode Phase 2 SA Established, IPSec Tunnel ConnectedJan 1 01:03:49 2010VPN Log(g2gips0) #4: [Tunnel Negotiation Info] Quick Mode Phase 2 SA Established, IPSec Tunnel ConnectedJan 1 01:03:49 2010VPN Log(g2gips0) #4: sent QI2, IPsec SA established {ESP=>0x575a01c0 <0x6534ae4e
So it even claims the tunnel should be up but I can never reach anything on the far side.
View 3 Replies
View Related
Feb 8, 2012
We have an RV042 on firmware version 1.3.13.02 and 2 ISPs:
WAN1 = Telepacific T1
1.5Mbps down and 1.5Mbps up
WAN2 = AT&T U-Verse
12Mbps down and 5Mbps up
I have it set to Load Balance, Primary WAN = WAN2
Network Service Detection enabled, only pinging the Remote Host of 4.2.2.2 and set to Generate Log
Bandwidth is set to:
WAN1 = 1000Kbps upstream & downstream
WAN2 = 5040Kbps upstream & 12000Kbps downstream
It seems to pick WAN1 a lot of the time. Do I have something setup wrong?
View 12 Replies
View Related
Dec 23, 2011
I have my RV042 set up in Dual WAN mode and both WANs are working properly. I would like to configure WAN1 to handle all traffic, unless it fails and then have everything to go to WAN2. Pretty much what Smart Link Backup does, however with that enabled only 1 of the WANs is live at any given time. I'd like both WANs to always be live as I'm going to see the second one as a back-door into the network. Is this possible to do with routing? I tried setting a routing rule to have everything to go WAN1, but when WAN1 goes down, nothing is rounted via WAN2.
View 0 Replies
View Related
Nov 11, 2010
Any working configuration to connect the iPad VPN-client (IPSEC) to the RV042?
View 16 Replies
View Related
Jun 4, 2013
I have a RV042 router on a single WAN and an internal LAN. I have configured port forwarding as follows: HTTP[TCP/80~80]->10.0.0.6HTTPS[TCP/443~443]->10.0.0.6IMAP[TCP/143~143]->10.0.0.5IMAP SSL[TCP/993~993]->10.0.0.5SMTP SSL[TCP/587~587]->10.0.0.5
Everything works just fine when I have the firewall DISABLED. However, when I enable it the behaviour is erratic. 1 out of 10 attempts to connect to ANY port forwarded works. Almost all attempts time out. Notice that this happens even if using only the default firewall rules (which should be bypassed by the port forwarding as I read in other posts).
My second try was to create firewall rules manually, overriding the default ones. I tried adding rules from source WAN1 (where my connection is) to ANY and to SINGLE IP's on every port. Nothing seems to work.
I don't know what I'm doing wrong, this is really bugging me. I had to turn the firewall off so we can access our servers from outside the office. This shouldn't have to be done.
Just found out that my firewall is getting LOTS and LOTS of Blocked - SYN Flood entries. I think this is why we are having trouble with the firewall. Could this be the problem? I have no idea where all these SYN packets are coming from since they appear with spoofed IPs or come from different bots all over.
View 1 Replies
View Related
Jun 1, 2012
My internet stopped working all of the sudden on my 2nd computer my 1st computer works fine (using atm) my 2nd computer stopped working all of the sudden it worked fine for about 2 years but the internet just went off for some reason it shows a computer with a yellow triangle with a black exclamation point on the bottom right corner it says connected but with limited connectivity ive tryed everything i know it is a windows XP i even bought a new internet cable today and the computer still does not work im new to these forums.
View 1 Replies
View Related
Sep 26, 2012
I was installing a IIS server to our client and created access - rules for http server and port translations. After that i noticed i lost local lan access trough vpn. Anyconnect and ipsec vpn. No other changes made to asa than those access-rules and nat changes. I'm trying to find out what is wrong, vpn connects okay, i can ping ASA but nothing else on inside network (for example dns server). Dns is not either working. When i ping local server, i can see in log.
View 8 Replies
View Related
Mar 27, 2012
I can no longer SSH to a primary active firewall. It had all of a sudden stopped working. However I am able to SSH to the secondary standby firewall without any problems. I did try to regenerate the RSA key on the primary fw, but still unable to connect. The only way I can connect to it is by using telnet.
I ran the "show asp table socket" command and I'm seeing port 22 listening on the primary IP address (not the standby), foreign address is 0.0.0.0:*. I did a packet capture on port 22 on the inside inside, seeing my request hit the fw and then right away a reset back from the fw.
version 8.2.(5)
model ASA5520
I'm hitting a bug in the software version I'm running? Or what else can I check before rebooting the primary fw?
View 6 Replies
View Related
Dec 13, 2011
it stopped booting up and now i cant talk to it.
View 5 Replies
View Related
May 25, 2012
I have tried a lot of drivers and even tried installing Vista 64 bit drivers (something that worked for someone in some thread), but it won't work.The adapter is recognized by the computer, but the smart wizard won't launch.
[code]...
View 4 Replies
View Related
Jun 30, 2011
My router has been working for close to 4 years now with minor problems, just stopped yesterday, All my PCs lost wifi access and then when I looked at my Linksys WRT300N only the 4 Ethernet port lights were on. Unplugged plugged it again, I connected one of the PCs to the one of the Ethernet port, the PC is reporting that there is nothing connected to the other side. It's been 4 years already, I do have a Linksys wireless G router even older than this which is till working. I guess its spoiled, I don't mind replacing it
View 4 Replies
View Related
Nov 11, 2011
I have been using a d-link router for some time now and since yesterday it has stopped working ( I have an orange 'world' light on all the time) After looking around this site I have tried resetting etc and nothing works. If I plug the ethernet cable into the modem I can get on the internet if I plug the cable into the router then nothing. These are the details I got from the config all when I plugged the ethernet into the router.
View 3 Replies
View Related
Jun 22, 2011
Randomly my router stopped working in the middle of the night. I didn't think the issue was with the router so i called the Tech Support people from Brighthouse and they told me to connect directly to the modem so i did that and I had internet. But why would my router randomly stop working, I've had this Linksys Dual N bound router for a year and never had a problem with it. I want to think that its the internet providers fault but I guess I really don't know.
View 2 Replies
View Related
Mar 3, 2013
I have a toshiba satellite laptop (windows 7) with wireless on-board and an ethernet cable port. Up until last night, both worked flawlessly since I bought the computer a few years ago.
Now, the wireless still works in three different locations I have tried (i.e. three different networks), but the ethernet cable will not work. I thought it was the ethernet connection on the mobo at first, but then after acquiring a USB-NIC connection, I found I had the exact same problem... I can't connect to my router or even direct to the DSL modem using a ethernet cable. I know my system is good since all my other computers (7) work with wired connections, and my laptop doesn't work on other cables on which other computers do. Essentially, it appears that my computer has lost the ability to get an i.p. address using an ethernet cable of any kind. Both the onboard card and the usb-nic cable tell me they are 'working correctly' in the systems/devices/network adapters section. I have tried disabling one while trying the other. I have tried disabling the wireless while trying either, and still nothing.
View 1 Replies
View Related
Sep 11, 2011
I currently own a Sony Vaio Laptop that has been working fine for the last 2 years, I was happily on facebook when all of a sudden, my laptop started lagging massively and it disconnected me from wifi, I was shocked to find that when I tried reconnecting, the laptop decided to stop working for a second and my wifi stopped working completely, every time I disconnect the Ethernet cable from my laptop even though my wireless switch is on, it won't even pick up my Virgin Media superhub I have about 5 meters from my laptop, it indicates that there is NO wifi anywhere, just the ascending bars with a big red X on it
View 1 Replies
View Related
Jun 29, 2011
My desktop was wirelessly connected to a router. It was working perfect, I did a wired connection from the modem to the desktop and when I tried to get the wireless connection again it has not been possible. When I try network trouble shooting I get DNS server might be unavailable. Been reading around and tried many of the things that I've read but none has worked so far.
View 4 Replies
View Related
Jan 24, 2012
I have been a loyal customer of a hosting company for over 10 years. The main reason I have a dedicated server is to eliminate those shared-hosting issues.For the past 4 years the service has been getting crappier. In fact; this week alone the ftp stopped working, mysql stopped working, and email.It is now to the point I have to move all my domains, mssql databases, mysql databases, email servers and countless files.I have been contemplating to set up my own dedicated server (Mac) and hook it up to my ISP. Most of the websites I host are local - only one or two are national/international.
View 5 Replies
View Related
Jun 24, 2011
I recently reinstalled Vista on my Dell laptop.Before that,I could view and open shared files on my XP desktop, although the PC couldn't see the laptop.Now, I can get online, but can't see the PC in Network places.I've ensured both have same workgroup name.I think it may be due to Norton Internet Security,which I've renewed and reinstalled from new disk.But the former one didn't prevent file-sharing, albeit one way,XP to Vista.Before I uninstall Norton again, is there anything else I should have done after Vista reinstall ?
View 1 Replies
View Related
Mar 5, 2012
My Linksys router stopped working. Resetting it didn't restore it.I bought a new Linksys E4200 router and configured it to the same settings as my old router. However, now I can't access certain website like Hotmail, Facebook, a weather site and others.But I can connect to most other websites, stream video, etc. Any suggestions why I can't connect to Hotmail, Facebook, etc???? I have 4 computers (3 wired, 1 wireless) connected through the router and they all do the same thing.
View 5 Replies
View Related
Jul 10, 2011
My router suddenly stopped working yesterday and I've tried everything I can think of to fix it. I have one computer wired directly in to it and a few laptops that use wireless connections.The power LED and the internet LED light up, but the status LED and the WLAN LED do nothing. Pushing the factory reset button on the back doesn't seem to do anything.Can't connect to the router site (192.168.0.1) The internet works fine when I plug in to it directly, so its definitely the router.
View 3 Replies
View Related
May 25, 2012
I used the wireless adapter (Netgear - WG111v3) on my computer for weeks without any trouble at all. (At the time i installed it, I remember I found out it didn't work/didn't work well on windows 7 so I downloaded some driver or something -- Don't really remember -- and it worked fine.) Suddenly, today, it stopped working. I have tried a lot of drivers and even tried installing Vista 64 bit drivers but it won't work. The adapter is recognized by the computer, but the smart wizard won't launch.
View 6 Replies
View Related
Mar 30, 2012
My computer stopped being able to Remote Desktop to my server on my network. My backup software also doesn't recognize my server. But, I can access its folders using Windows Explorer. Any other PC on the network can remote desktop to the server and connect. What happened to my machine? This message appears when i try to connect: "Remote Desktop can't connect to the remote computer for one of the following reasons:
1) Remote access tot he server is not enabled
2) The remote computer is turned off
3)The remote computer is not available on the network
Make sure the remote computer is turned on and connected to the network, and that remote access is enabled."
My computer is:
AMD: Athlon 64 X2 5200+ 2991 MHz
Mobo: Gigabyte M57SLI-S4 v.2
RAM: 4GB Mushkin DDR2 PC2-6400
OS: Win 7 64bit
VC: Geforce GTX 470
View 1 Replies
View Related
Mar 18, 2012
"Ethernet Connection has stopped working".Its stopped working again and I've run the Network Test and the results are in the file REG.txt attached. I can connect to the internet via wireless OK but I had wireless turned off to run this test.I've proven the ethernet cable OK by connecting another pc to it which works OK.
View 12 Replies
View Related
