I remember I did that one time on 2800 router with Gi0/0 and Gi0/1 to connect another port channel in 3560G switch. I have no way to try it in ISR G2 router like 2900 or 3900 now. I know the the ethernet switch module must support it. I wonder if the integrated interfaces support it or not.
View 5 RepliesI am trying to add WCCP to be configured for websense. My first option seems to be either purchase an IPServices license for the stack of 3750E switches, but i am thinking this will require us to license all three switches in the stack. The second option i am looking at is to do the WCCP configuration on the 2800 router we have on the edge. The problem is both Gig ports are in use, one going to the firewall and the second going to the ISP. My first question would be, which option is better in terms of manging as well as cost of implementing it.The second question is, if WCCP on the router is a better option, what is the add on module i should be looking to get to add the additional ports to hook up the Websense cache.
View 8 Replies View RelatedLooking for multicast over IRB interfaces. My full config below, works as expected on a Cisco 1760 router (IOS 12-4) but fails strangely on our Cisco 2800 (IOS 15-1) and Cisco 1941 G2 routers.
I use Windows 7 Enterprise and VLC 2.0.0 Two Flower as the multicast video receiver. On the 1760 router, I open VLC, request the video (rtp://@239.255.0.1:5004) and it plays flawlessly.
We have to upgrade the older outdated unsupported Cisco 1760 routers. We replace the Cisco 1760 router with a Cisco 1941 router. Configuration differs ONLY in the interface speeds; F0/0 to G0/0 and that is just bout it. Using the same Windows 7 Enterprise PC, I open VLC again and request the video -same as before; No video and no voice. We swap the 1941 out and put in the 1760 again, multicast works flawlessly. If we put the 1941 router back in, multicast fails again. We put the Cisco 2800 series router in and it also fails the same as the 1941 router.
Troubleshooting, I open VLC and request the same multicast video. On the same PC, I open Wireshark and start capturing packets, - and instantly the VLC video starts playing. I close Wireshark and the video stops. I open Wireshark and start capturing packets again and the VLC video starts playing again.
Wireshark shows the video packets are being received from the source when VLC is requesting the video. If I close VLC while Wireshark is capturing packets, Wireshark shows the video stream stops.
Shows the correct multicast sources, incoming and outgoing interface details
Incoming interface is Serial
Outgoing interface is BVI
Show ip pim rp
Reveals the correct RP details
[code]...
I came across this Multichassis EtherChannel Features when read about information from Cisco Smart Business Architecture.After checking further, knowing that Cataly stwitch 6500 supports this feature.provide information that beside Catalyst 6500, is there any other model of Catalyst switch can support this feature?
View 4 Replies View RelatedI have a client that that is installing a new network. They have requested the use of an CISCO891W-AGN-A-K9 mostly to be consistent with upgrades perfomed at other sites. I agree with the use of this router, so that's OK. The issue is that they have requested that I use the integrated PoE available on this model. I'm also OK with this as it will make a much neater installation. However, I can't seem to find much information on how to get the integrated PoE. I need clarification as to whether I can get a kit to upgrade this router. I generally purchase from sites like newegg or cdw (I'm an independent contractor) and I can't seem to find one with it. I have found some information on 800-IL-PM-4 and 800-ILPM-4 (who could confuse those ). Are they the same or different? Which one is the correct one and does it include the AC power adapter and can if be retro'ed into a router without the PoE?
View 2 Replies View RelatedI have 3850 switch with integrated WLC and i wonder if i can access the WLC via GUI ,also i need to know if it support Dynamic vlan assignment over SSID.
View 2 Replies View RelatedI configured an Etherchannel two interfaces (Gi0/37 and Gi0/39) in a CiscoWS-C2960G-48TC-L, which is connected to an HP Blade, where they spend 2vlan (16 and 17). The point is that they got these interfaces on a trial and upload these were in sleep mode produces the following log.
Sep 1 16:04:38.649:% EC-5-CANNOT_BUNDLE2: Gi0/37 is not Compatible with Po1 and Will be suspended (trunk mode of Gi0/37 is dynamic, is Po1 trunk)
Sep 1 16:04:38.733:% EC-5-CANNOT_BUNDLE2: Gi0/39 is not Compatible with Po1
and Will be suspended (trunk mode of Gi0/39 is dynamic, is Po1 trunk
I am trying to figure out how to create an etherchannel with sub-interfaces on an asa 5520 running 8.4.1 code. It doesn't seem to allow me to configure any type of sub interface on the port-channel or anywhere else once I create it.
View 4 Replies View RelatedI came accross a Cisco 1801 router. As I understand it supposed to work with a dsl connection for internet access and configuration. I have cable internet access at home and since cisco routers are very versatile, I want to know if I can integrate this router into my home network, as a secondary router, and use it for its SSL vpn capabilities?
View 11 Replies View Relatedopen specific ports on 1941w Integrated Services Router.This specific router is a wireless VPN router that has a wired module and a wireless module and VPN so I'm getting 3 subnets on my network - 192.168.1.. for the wired connections, 10.100.1.... for wireless LAN connections and 10.100.2... for VPN remote connections.I know that by default all connected computers can access my Linux server data through telnet so the telnet port is open by default, the problem is that I have some other software licensing system on my Linux box that needs to be accessed through port 27000 and most of my users are using wireless connections and can't access that license because post 27000 is closed.what is the comand to open this post or any other port that I need to be open on the wired module, wireless module and VPN or at least poit me to somewhere where I can find all the commands that I can use for this router?
View 6 Replies View RelatedAs LACP or even PAgP? I can't believe etherchannel is only supported on 8.4 up...
View 2 Replies View RelatedWhen I try to add an IP address to a port-channel interface on a 3845 ISR I am getting an error that seems to imply that only L2 etherchanneling is possible. Am I missing something?Cisco IOS Software, 3800 Software (C3845-ADVIPSERVICESK9-M), Version 12.4(24)T8,
sfo-c3845-1#sho run int port-channel 1
Building configuration...
Current configuration : 31 bytes
!
interface Port-channel1
end
[code].....
I am trying to implement an etherchannel on a cisco 2901 (IOS 15.1). i have already created the port-channel but i cannot assign the gig interface to the channel group.
View 1 Replies View RelatedI have a problem with an etherchannel between a cisco 2950 and a couple of catalyst 4506. The cisco 2950 is connect via an etherchannel to the catalyst 4506A. The channel consist of two port on both side and is in trunk mode, encapsulation dot1q.Now i have the necessity to connect the 2950 to the other catalyst, 4506B. So, i copy the same configuration on the 4506B, but when I unplug the two rj45 cables from the catalyst 4506A to plug them in the 4506B the etherchannel doesn't go up in any way.
View 8 Replies View RelatedI have two switches 6509 one switch is confire with VTP domain ABC Other switch is configure with ABZ, At present the switch is configure with the L3 interface and one fiber cable is connected between two switches.I want to remove L3 configuration wants to make L2 etherchannel and wants to ceraeate Loop back will assing same ip both side.The OSPF is configure both side , i will not do any changes in the OSPF as L3 ip is advertise in OSPF.
View 1 Replies View RelatedIf the ports on a 5508 can only perform etherchannel(no LACP or PAGP), only on mode, how does a 5508 create a bundle with a nortel switch?
View 1 Replies View RelatedI am about to configure 4 Gig ports for EtherChannel. I've been reading about EtherChannel and it seems easy enough to configure. I have a host (server)which I am going to connect to these 4 - gig ports. This is new for me and would like some feedback for those that have used EtherChannel on their layer 2 switches. The gig ports will be an access port with VLAN XX.
View 6 Replies View RelatedIs it possible to have ether-channel across 2 switches? As an example, having a server with 2 ports connect, 1 port to Switch-A and the other to Switch-B and then use those two links on the sepatate switches but to the same server to form an Etherchannel.
The Switch-A and Switch-B are 3560 series
We have two 6k5 configured as vss and it is working fine. For each floor we have a 3750 stack. In each 3750 stack we have 4 switches. From the first 3750 we have a fiber link to the first 6k5 and from the fourth switch we have another fiber link to the other 6k5 switch, for each floor/3750 stack, both configured as etherchannel. We installled each 3750 stack/floor in different maintenance windows; in all these installations we have problems configuring the etherchannel. After we configure the etherchannel on 3750 stack and in the vss, the etherchannel does not go up/up. We see the etherchannel up/down; after a lot off work, try and error, configuring shut/ no shut, adding and excluding links from the etherchannel; in any aleatory moment the etherchannel goes up/up and works fine. Is there any bug related with these IOS versions, or is there any right procedure to configure etherchannel from vss to 3750 stack?
3750 stack config (IOS
Cisco IOS Software, C3750 Software (C3750-IPBASEK9-M), Version 12.2(50)SE1, RELEASE SOFTWARE (fc2))
interface GigabitEthernet1/0/1switchport trunk encapsulation dot1qswitchport trunk allowed vlan 100,101,371,372switchport mode trunkchannel-group 1 mode on!interface GigabitEthernet4/0/1switchport trunk encapsulation dot1qswitchport trunk allowed vlan 100,101,371,372switchport mode trunkchannel-group 1 mode on!interface Port-channel1switchport trunk encapsulation dot1qswitchport trunk allowed vlan 100,101,371,372switchport mode trunk
[code]....
I am trying to review the port-channel configuration on a 6500 series. I am issuing the "show etherchannel summary" command and the out put shows the Group, Port-Channel, and Ports. It does not show me the protocol that is in use such as PAgP or LACP. Does this have to do with the Etherchannel in the "On" mode rather than "active", or "Auto"?
View 2 Replies View RelatedWe have a problem with the throughput over etherchannel in LACP with 2 or 4 ports. It is iSCSI traffic (vmware esxi 4.1 U3) is going from 2 separate NICs (ports) to the etherchannel (with 2 or 4 ports) that has a SAN connected (Nexenta).
The SAN is configured in passive LACP and the switch is in active LACP. Actually it does not matter if we do LACP or just MODE ON, still same result: ~1GBit/s throughtput in either direction. Like already mentioned, 2 or 4 ports in the etherchannel make no difference, or the configuration of the etherchannel.
I will post some config data below, but here is the question: Why can't we see traffic beyond 1GBit/s? Source and destination are capable of doing much more than that (vmware esxi RAID 5 of 1TB SATA; SAN 16 x 1TB NL-SAS). If we look with CNA, we can see that the traffic is balanced equally over the etherchannel ports. With or without QOS or flowcontrol, no difference. This whole traffic happenes on this switch.
!
port-channel load-balance src-dst-ip
!
interface Port-channel5
[Code]....
When you aggregate multiple fiber GBICs together on the 3508G, do you configure it as an etherchannel, or as fibre-channel? I've looked around online for hours, but can't find it mentioned anywhere.
View 3 Replies View RelatedI have made an etherchannel between 6509 and 7606 with two giga interfaces on eatch one to have more bandwidth (2Go), but the Etherchannel does not exceed 1 GB (Below is a capture for Etherchannel taken from Solarwinds).the both 6506 and 7606 use ws sup 720 3bxl
View 8 Replies View RelatedIs it possible to to build a Layer 3 ether channel from two separate physical switches (layer3) that are trunked together?I know you can easily do this on a single switch and on stacked switches which I've done but in this case the customer have purchased two 3560X's which are not stackable yet want redundancy. The purpose of the etherchannel is to connect both switches to a private circuit provided by the hosted partner then route to the same setup in the DR location to different subnets.
View 4 Replies View Relatedseeking for configuration assitance on etherchannel between catalyst 3750 and 6506
View 3 Replies View RelatedI was configuring link aggregation between a Cisco3750 and Cisco SG200 and the switched network went down just a few minutes after the port channel came on.I rebooted the SG200 and all hosts came back up for a minute before I lost them again. The etherchannel was between two trunking ports. I never set link aggregation on the SG200, could that be the reason? All machines are connected to the SG200. The 3750 is only being used as a layer 3 device for inter vlan traffic.
View 1 Replies View RelatedMaybe this was listed in the release notes for the product and I missed it, but can this item support Etherchannel in a 2801 router? I installed the module into the router and the router recognizes the module. I can configure the ports as access or trunk ports, but I am unable to configure the channel-protocol or the channel-group for the Etherchannel. The IOS on the router is 15.1 M with the upgraded Bootloader version 12.3.
View 1 Replies View RelatedWe have a new building where we added 3 network closets with 3750x stacks.We have 2 fiber gig ports connected to 2 microwave units and etherchanneled the to ports
We have the same setup at the corporate office except the connection is 2 fiber gig ports on a 6509. The 6509 is doing the routing
Now the problem is that we lost the connection to the management interface on only one of the three closets after a few days running. But some workstations at the corp office could reach it... others could not. The workstation were on the same VLAN. We solved the problem for a few days by shutting on of the fiber ports on the etherchannel. But is started happening again... now with PCs being installed at the new location.
The PC that was not working on the 3750x side could ping across to the 6509 but no further then that. It seems like an arp issue not routing because some devices are reachable and fully operational throughout the network.
Here is the configuration:
3750x:Cisco IOS Software, Version 12.2(55)SE1
Current configuration : 118 bytes!interface Port-channel1switchport trunk encapsulation dot1qswitchport mode trunkno snmp trap link-statusend
!interface GigabitEthernet1/1/1description 2gig to STB-6509switchport trunk
[Code]......
I been practicing with the configuration of layer 3 etherchannel configuration and i am facing a problem here. I have two 3560 switches and i want a layr 3 ether channel configuration setup between the first 2 ports of bothe the switches. I assign IPs to the Port-channel 1 of both the switches "10.1.1.1 /24 and 10.1.1.2 /24" but i am unable to get a successful ping. what am i doing wrong. below are the configs for bothe of my switches.
3560_1
Building configuration...
Current configuration : 1274 bytes
!
version 12.2
no service timestamps log datetime msec
no service timestamps debug datetime msec
[code].....
I would just like to confirm if it is possible to create a 2x10G etherchannel on a 4948.
View 4 Replies View RelatedWe have to cisco WS-C4900M with Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500e-IPBASE-M), Version 12.2(53)SG5, RELEASE SOFTWARE (fc1).We have four gigabit link connected between those two switches.We have create a LACP port channel with those four ports on both switches. Ether-channel is up and running and defined with a load-balancing method of src-dst-ip.But when we test the load-balancing, it's not using the src-dst-ip rule with the XOR: [code]
View 5 Replies View RelatedI'm trying to configure and etherchannel between 2 switches. A 3750 and a 3750G, but the port channel is down: 3750. [code]
View 2 Replies View Relatedon 7600 SUP720 3B.I have port channel and there are two ports on that port channel. is it possible to apply this command? does it work?
View 1 Replies View Related