Cisco WAN :: 891W / Using Private IP To Simulate ISP - Unable To Ping WAN IPs
Jun 21, 2012
i have a home lab network that is connected to my internet. I basically have a linksys router connected to cable modem and in order for my families internet to not go down while testing and learning my CCNA I am trying to treat the Linksys as the ISP.
1. Plugged my 891W router via FASTETHERNET 8 (192.168.1.10) into LAN Switch port 1 of my Linksys E4200 home router(192.168.1.1).
2. I plugged my 891W Gigabit 0 (10.10.10.1) LAN side into my 2950 Catalyst Switch (10.10.10.5 - VLAN 1)
3. my 2950 Catalyst switch (10.10.10.5 - Vlan 1) is plugged into my 2600 series router via the routers FE port (10.10.10.2).
There is a few more routers connected behind r2 but I am not dealing with them right now and there is also a switch connected into s1 but its not being used for this.
891w is labled r1
2950 is labled s1
2600 is labeled r2
I am running RIP Verison 2 for my network protocol.
r1 information below
----------------------------
r1#show ip protocols*** IP Routing is NSF aware ***
Routing Protocol is "rip" Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Sending updates every 30 seconds, next due in 24 seconds Invalid after 180 seconds, hold down 180, flushed after 240 Redistributing: rip Default version control: send version 2, receive version 2 Interface Send Recv Triggered RIP Key-chain GigabitEthernet0 2 2 Vlan4 2 2 wlan-ap0 2 2 Automatic network summarization is in effect Maximum path: 4 Routing for
[code].....
I can ping all over my homelab everything I can reach as long as I have a protocol up but I cannot reach the WAN IPs. I watched video by Jeremy Ciorara and I tried to follow the wan and nat part from a website [URL] And none of its working. I am not sure if this is a case where a private IP cannot function as a ISP and I am breaking some rule thats not mentioned in CCNA studies or if its something else. I tried these commands from Jeremy Video:
r1(config)#ip access-list standard "NAT_ADDRESSES"
r1(config-std-nacl)#permit any
r1(config)ip nat inside source list NAT_ADDRESSES interface fastEthernet 8 overload
However they did not work it was pretty close to whats in the basic website up there I listed as well. I think I went back to the basic configuration in the config file post above. Its really frustrating as I follow directions and they do not seem to work. I understand I am using my private 192.168.1.0 subnet as an ISP and maybe that has something to do with it but when yoru first learning and things dont work its kind of overwelming as you have problems seeing the big picture and dont yet trust in things you have learned as they are unfamiliar so its easy to get lost.
We have had a successful site to site vpn working for several months now. It is an ASA 5510 at HQ to a ASA 5505 at a branch office in another state. We just added a second site to site vpn in another state this time from HQ to a Sonicwall TZ100. After plugging in the Sonicwall to the Qwest modem in bridge mode the tunnel came right up. I was unable to to ping any off the private IPs at HQ from the new branch, but was able to use remote desktop into the servers and workstations at HQ. Also all the computers show up when browsing the network from the new branch.
At the first branch we are able to ping both ways and use remote desktop both ways.When using packet tracer in ASDM on the HQ ASA and pinging from one of the IPs in the HQ protected network to an IP in the new branch network NAT-EXEMPT looks good, but when it hits the first NAT it matches on the "dynamic translation to pool 10 (10.1.255.254) [Interface PAT]" (which is the default route for all the vlans to get to the Internet.)The next NAT (subtype - host-limits) looks better and this one going to the IP address of the outside interface of the HQ ASA 5510, but then the third NAT (Subtype - rpf-check) reverts back to the "10 (10.1.255.254) Interface PAT]" and the packet is DROPPED. Also there is no VPN step in Packet Tracer after NAT.[code]
Is the problem possibly due to the fact that my 2 new ACLs for "encrypt_acl-30" fall after "access-list global_mpc extended permit tcp any any" in the config and it is running into the implicit deny all?
Opening a connection to integrated AP801 wireless device for performing wireless configuration tasks, the connection is established OK, authentication is passed OK using credentials from main configuration file, gaining level 15 privileges with enable command, but after that... no way to enter "Global Configuration mode" because there are no "configure" family commands present!!! Simply can't say "Conf t" because there is no such command!
Any issue creating a guest vlan to use the WIFI on an 891W router? The IOS is version 15.1. I have created discreet Vlan's and setup subinterfaces on both the WLAN_AP0 and GigaEthernet 0 interfaces with dot1q encapsulation. The client will receive an IP from the pool but cannot ping or connect beyond the default gateway.
The external interface is using Nat overload and all wired clients are successful in connecting to outside addresses. I have insert a permit any statement in the acl which affects the external port but still no success.
We have configured a Cisco ASA 5505 with AnyConnect access. This works great. However, these users cannot seem to ping devices on the private network. We have configured all devices on the network with a 10.10.10.0/24 address space. The inside interface of the ASA i 10.10.10.1/24 and the VPN return addresses are 10.10.10.50 - 10.10.10.65/24.They users can utilize SSH and Oracle or MySQL calls but cannot seem to ping. Obviously, I am over looking something.
From My Router that connects to Cable modem i am unable to ping website 4.2.2.2I am able to ping all other websites fines.Same website i can ping from my pc and all other switches fine.Router has only 1 ACL thats for NAT.
I have RV110W connected in private network 192.168.5.0/24, I have redirected pptp port from adsl modem to the RV110W and VPN works OK. DDNS on the adsl modem is not available.I need to use Dynamic DNS functionality on my RV110W. The device supports several DDNS services (TZO.com, Dyn DNS.com, 3322.org and noip.com). For all but TZO the public "Internet IP Address" shows as 192.168.5.110, which also gets auto registered with the DDNS service.I have tested this with free noip.com account and this is obviously undesired behavior. I need the router to register my real public IP.For TZO it shows the proper public IP, but TZO service is no longer available on TZO.com.
I'm an IT student and I've been assigned with homework simulating a network including an ISA server and some clients in Packet Tracer but I can't find anything which can be configured like an ISA (Internet Security and Acceleration) server(this is kind of Microsoft's technology as I know) in Packet Tracer, the generic Server from the devices box has only some basic services such as HTTP, DHCP, DNS, FTP, AAA, ... but none of anything related to ISA, all the servers in Packet Tracer have only 1 interface whereas the ISA server (as far as I know) should have at least two interfaces, and there is also no CLI supported for those servers so I think I can't simulate ISA server in Packet Tracer, can I?
Any good way to force a serial link to delay packets to simulate a hi latency WAN link? Found this command so far:
Router(config-if)# transmitter-delay hdlc-flags
I can dial the speed up/down via clock rate all good but I need to also simulate latency. This is for simulating a WAN bonding scenario so I was going to aggregate a 10M ethernet port with a 2M serial and a 512k serial. But I need to also ensure varying latency.
We have an ACS 4.2 installation and we have users configured on the user setup, they authenicate using the windows database (AD). We ran failure tests and simulated AD failure but disabling the firewall rule. So the ACS server is up, AD is down. Tested user login to a switch and get the following error. External DB user invalid. It looks like as the ACS does not get a response from AD it rejects the user login.
What we want it to do is in the event of AD failure is to be able to login to the switch with the username configured on the switch. (as if ACS server does not respond)
Date Time Message-Type User-Name Group-Name Caller-ID Network Access Profile Name Authen-Failure-Code Author-Failure-Code Author-Data NAS-Port NAS-IP-Address Filter Information PEAP/EAP-FAST-Clear-Name EAP Type EAP Type Name Reason Access Device Network Device Group 02/03/201214:09:13Authen failedtest.testNetwork192.168.1.1(Default)External DB user invalid or bad password....tty310.0.0.1..........SWITCH30Office
I have run into a problem replacing an old Linksys BEFVP41 with a SA520. The BEFVP41 had an address on the LAN defined as a DMZ. That address was another router. It is in the same subnet as the local LAN and I am not sure what ports it uses. It is controlled by an outside group and requires much delay and paperwork to change the address. The new SA520 will only support a DMZ if it is in a different subnet than the LAN. Any way to simulate the old DMZ function on the newer router? I have not yet been able to obtain a list of all ports that should go to the second router. Didn't know if there was a way to forward all ports like the old BEFVP41 does by setting a DMZ address.
*I have 2 cisco routers 2811 router A&B*using 0/0 for WAN and 0/1 for LAN on both routers*both routers are connected together with crossover cable to 0/0. recieve link and activity*both routers are on the same subnet Router A:0/0 192.168.1.1/24 - router A:0/1 192.168.2.1/24 ; Router B:0/0 *192.16.1.2/24 router B:0/1 192.168.3.1/24*I can ping the inside and outside address of both router from PCs connected at its respectable end. *PC A 192.168.2.2/24 PC B 192.168.3.2/24 *when connected to router A 0/1 and I try to ping router B 0/0 it times out in DOS* but I AM (CAN) able to ping from PC A to router B 0/0 in hyperterminal, telnet and Cisco SDM. I just CANNOT ping in DOS?
I have created a site to site Ipsec vpn with a cisco 2610 and a linksys RV042. Running a show "crypto isakmp sa" command I get a qm_idle status and when running a "show crypto ipsec sa" I see that packets are being decrypted and encrypted. Also when running the "show ip access-lists" command I do have matches to that connection.The problem is that I am unable to ping hosts from one network to another. For example, from the Cisco router in network 192.168.0.0 I am unable to ping the remote network 192.168.2.0 and vice versa.
I am not sure what is happening. Do I need to create a route to that remote network? I guess it could also be a problem with NAT or an ACL.Here is what running-config shows:
I am connecting a 2600 router to an ISP. Interface 0/0 is connected to the ISP using DHCP. Interface 0/1 is connected to the inside providing DHCP services to the inside. At least it should only be providing DHCP services to the inside. I also have a public static IP that is NAT to a private static IP. Everything is working except the computer on the static IP. From the router I am able to ping inside and out from each interface. I am able to ping both interfaces of the router from the computer on the static IP but I cannot ping outside the router. If I do a debug all I see a reject for the gateway of the static IP but it has “mobile IP” in the text string. Not sure what mobile IP is relating to. Networks are as follows:
I've been called upon to fix the SSL VPN issues in our ASA5505. The issue I am having is that I am able to log into the vpn, access the internet, but I'm unable to access anything on the LAN. I can't use ping or use DNS.
I'm using ASDM v. 6.2(1) and ASA verison 8.2(1). I'm not comfortable using the CLI and prefer the GUI.
We have many CT/MRI etc. machines and Servers in the Hospital LAN. Now intermittently we are loosing the LAN connectivity i.e we are not able to ping any system from any node inside the hospital network for sometimes, after some time it will start working and then again it will stops again.We are using procurve switches and also we are not using any router
I'm trying to do port forwarding on my DIR-615...first of all I need to be able to ping the router from outside! I did enable the ping options to allow request from WAN...still don't work!!I removed the router and plug my laptop directly on my cable modem adapter and I'm able to ping my IP address (did put the same address the router had)...so, the IP is OK and it is possible to get in the modem from outside.I did plug back the router, and still not working...I did some trick like enable all IP with the Inbound filter...give access to few MAC address that I have to give more chances to get in and still not working!!!
I have a client that that is installing a new network. They have requested the use of an CISCO891W-AGN-A-K9 mostly to be consistent with upgrades perfomed at other sites. I agree with the use of this router, so that's OK. The issue is that they have requested that I use the integrated PoE available on this model. I'm also OK with this as it will make a much neater installation. However, I can't seem to find much information on how to get the integrated PoE. I need clarification as to whether I can get a kit to upgrade this router. I generally purchase from sites like newegg or cdw (I'm an independent contractor) and I can't seem to find one with it. I have found some information on 800-IL-PM-4 and 800-ILPM-4 (who could confuse those ). Are they the same or different? Which one is the correct one and does it include the AC power adapter and can if be retro'ed into a router without the PoE?
Alright, well I have a Cisco 891w router and have just about everything up and ready to deploy. I'm primarily using Cisco CP 2.4 to provision the router with minor tweaks being done in the CLI. I want to set up a filter to allow access to roughly 20 websites for the majority of my network which is all on the same VLAN. The ip ranges are x.x.x.10 - x.x.x.169 which I have set into a Network Object group called limitac. The second group ranges at x.x.x.170 - x.x.x.199 and is called allowac. I have set up DHCP bindings for all the devices that will connect to the network but I want to set up a web filter for only the first group. I cannot seem to find anything in the Cisco CP manual or the IOS manual for setting up filtering for a range of IPs only. Primarily there are a few computers that need full access to the web while the others should only have access to the sites I set up in the filter.
I am having problems connecting an 891w to a WLC, is it possible to have to separate vlans, one for the Lan ports and another for the AP module.
I do not want the AP part of the 891w in autonomous mode. The WAN port of the router will be connected to a DSL type service.
Is there a guide or something to get a 891W to connect to the WLC?
I would like to have users on a data vlan (vlan1) connecting to the network like a normal router, then the AP module to connect to the WLC via a different IP probably vlan 2
On the WLC itself i do not see any attempts in the logging.
What I currently have is a Cisco 891W Router as well as two ISP's (both with dynamic IP's) in. I'm currently just running one of my modems into the 891 through the FE8 port and then if for some reason I have an internet failure switching the ISP modems. What I'm wondering is if there is a fairly simple way to configure (and attach) both modems to this router and then set it up to handle this failover automatically?
I believe I have the steps done at the IOS to config the WAN port for SSH, but I still can't connect to it. I have "logging console 7" on so I am able to see that the router is dropping my TCP session requests. I figure this is just the built-in zone-based firewall at work.
Is there a very straightforward process, via the IOS, to allow SSH inbound on the WAN port? I'm not very familiar with the IOS other than basics so while I know how to do things like "transport input ssh" and "login local" and such on the vty 0 4 line, I have no idea whatsoever on what I should do with the firewall stuff. I believce the WAN interface is already a member of the outside zone though so I imagine one just has to somehow include ssh (preferably on a non-standard port) in the exceptions on the firewall somehow.
I have been poking around for a step-by-step IOS guide for this but only find info on configuring SSH itself but not how to open the firewall to allow the connection for it through.
I am currently working on a 1941w router. The problem that I am having is that I am unable to ping the switch that is directly connected to it and I am unable to ping from the switch to the router. If I take the address off of vlan 1 and move it to gi0/0.1 the pings work, but then client traffic on the wireless ap inside the 1941w fails.
Here is the releveant config off of the 1941w
version 15.0 no service pad service timestamps debug datetime msec localtime show-timezone
im trying to connect a dell MD3000i to a Cisco 3750-s but i am not abel to ping the server.the status is up and Protocol is up. but still nothing.i configerd the port to be a acces port and also at trunk port but still nothing is happening.
host PC (192.168.9.3) -----> gateway (192.168.9.2) ----- Pix E1 (192.168.9.1)/Pix E0 (81.x.x.250) ------ Internet
The 192.168.9.2 gateway is a 3560 switch connected to the PIX. I can ping out to the Internet via IP from the PIX, but not via the host PC (192.168.9.3) on the LAN. PIX and gateway configs below. Am I missing something that's preventing me pinging out to the Internet from the internal LAN?
PIX config
test-cal-pix01# sh run : Saved : PIX Version 8.0(3) ! hostname test-cal-pix01 enable password btf1YD.Vq7mE6vEA encrypted
i have a site to site vpn stablished, the vpn works fine (while is up), i have a cisco asa 5520 and the other end of the vpn is a jupiter device that for technical reasons needs to send a continuos ping and when it does not receive a reponse back it brings down the vpn tunnel and reestablish it again. while the vpn is up traffic flows perfectly but because i m unable to repond to the ping the vpn is brought down as reestablished by the jupiter device. the jupiter device pings the encryption domain which is an ip that is natted to the real ip in the inside network. this is my configuration of the vpn:
AAA.AAA.AAA.AAA is the ASA public ip in the outside BBB.BBB.BBB.BBB is the jupiter device ip (part of the object group IP_LIST) CCC.CCC.CCC.CCC is the nat ip on the ASA 10.21.0.164 is the real address in the inside(code)
I have 3 2620xm routers connected via dte/dce serial connections In a lab.One of the routers Is also connected to a 2950 switch.
The 2950 switch connects to an unmanaged tp-link switch that Is connected to a dsl modem/router.I have Internet access via the 2950 to my laptop.
I have ripv2 enabled on all the routers and It's working fine.The dsl modem, switch and connected router are on the same subnet.
When I ping the dsl modem via the 2950 or via the router connected to the 2950 , It works 100%.If I ping the 2950 from either of the other two routers , It also works 100%.I can't ping the dsl modem however from the other two routers.I've only been studying for the ICND1 so maybe there's something I'm missing here.
This is what I have as a setup:BT Home Hub wifi routerPC with Windows 7 Home premium connected via ethernetMacbook Pro with OSX10.6 connected via wifiIt feels like i've tried everything to get this working. As far as I can see the settings are all ok but I've noticed that I can't ping the PC from the mac although I can ping with success the other way around tried traceroute from the macbook and it gives me this so it is able to see it somehow...Code:traceroute to 192.168.1.66 (192.168.1.66), 64 hops max, 52 byte packets 1 alistair-pc.home (192.168.1.66) 1.724 ms * 1.151 msNot sure where to go from here. I think discovering that ping is failing is a good start to diagnose.
