Cisco :: Unable To Ping In Dos?
Mar 9, 2013
*I have 2 cisco routers 2811 router A&B*using 0/0 for WAN and 0/1 for LAN on both routers*both routers are connected together with crossover cable to 0/0. recieve link and activity*both routers are on the same subnet Router A:0/0 192.168.1.1/24 - router A:0/1 192.168.2.1/24 ; Router B:0/0 *192.16.1.2/24 router B:0/1 192.168.3.1/24*I can ping the inside and outside address of both router from PCs connected at its respectable end. *PC A 192.168.2.2/24 PC B 192.168.3.2/24 *when connected to router A 0/1 and I try to ping router B 0/0 it times out in DOS* but I AM (CAN) able to ping from PC A to router B 0/0 in hyperterminal, telnet and Cisco SDM. I just CANNOT ping in DOS?
View 10 Replies
ADVERTISEMENT
Jan 18, 2013
From My Router that connects to Cable modem i am unable to ping website 4.2.2.2I am able to ping all other websites fines.Same website i can ping from my pc and all other switches fine.Router has only 1 ACL thats for NAT.
View 25 Replies
View Related
Mar 25, 2011
I have created a site to site Ipsec vpn with a cisco 2610 and a linksys RV042. Running a show "crypto isakmp sa" command I get a qm_idle status and when running a "show crypto ipsec sa" I see that packets are being decrypted and encrypted. Also when running the "show ip access-lists" command I do have matches to that connection.The problem is that I am unable to ping hosts from one network to another. For example, from the Cisco router in network 192.168.0.0 I am unable to ping the remote network 192.168.2.0 and vice versa.
I am not sure what is happening. Do I need to create a route to that remote network? I guess it could also be a problem with NAT or an ACL.Here is what running-config shows:
crypto isakmp policy 1
encr 3des
hash md5
authentication pre-share
group 2
lifetime 28800
View 5 Replies
View Related
Oct 26, 2012
I am connecting a 2600 router to an ISP. Interface 0/0 is connected to the ISP using DHCP. Interface 0/1 is connected to the inside providing DHCP services to the inside. At least it should only be providing DHCP services to the inside. I also have a public static IP that is NAT to a private static IP. Everything is working except the computer on the static IP. From the router I am able to ping inside and out from each interface. I am able to ping both interfaces of the router from the computer on the static IP but I cannot ping outside the router. If I do a debug all I see a reject for the gateway of the static IP but it has “mobile IP” in the text string. Not sure what mobile IP is relating to. Networks are as follows:
0/0 DHCP 10.X.X.X
0/1 192x.x.x
Static 75.X.X.X
[Code].....
View 13 Replies
View Related
Apr 26, 2012
I have the following setup where the Cisco ME 3400 provided by the ISP.
My Cisco 2911 is configured as below:
CORE_Router#sh run
Building configuration...
Current configuration : 6075 bytes
[Code].....
View 6 Replies
View Related
Aug 18, 2011
I've been called upon to fix the SSL VPN issues in our ASA5505. The issue I am having is that I am able to log into the vpn, access the internet, but I'm unable to access anything on the LAN. I can't use ping or use DNS.
I'm using ASDM v. 6.2(1) and ASA verison 8.2(1). I'm not comfortable using the CLI and prefer the GUI.
View 13 Replies
View Related
Mar 9, 2011
We have many CT/MRI etc. machines and Servers in the Hospital LAN. Now intermittently we are loosing the LAN connectivity i.e we are not able to ping any system from any node inside the hospital network for sometimes, after some time it will start working and then again it will stops again.We are using procurve switches and also we are not using any router
View 2 Replies
View Related
Sep 14, 2012
I m not able to ping from one to another with the os win XP n other with win 7.
View 1 Replies
View Related
Jul 29, 2011
I'm trying to do port forwarding on my DIR-615...first of all I need to be able to ping the router from outside! I did enable the ping options to allow request from WAN...still don't work!!I removed the router and plug my laptop directly on my cable modem adapter and I'm able to ping my IP address (did put the same address the router had)...so, the IP is OK and it is possible to get in the modem from outside.I did plug back the router, and still not working...I did some trick like enable all IP with the Inbound filter...give access to few MAC address that I have to give more chances to get in and still not working!!!
View 6 Replies
View Related
Sep 9, 2011
I just tried to configure my ASA but unable to ping. My setup is as follows:
Cable Modem (DHCP from IPS)---> ASA (192.168.1.1)--->Belking Router (192.168.5.1)--->Switch (192.168.5.14)--->
ASA Version 8.2(3)
!
hostname WoodHomeASA-1
[Code].....
View 30 Replies
View Related
Oct 10, 2011
I am currently working on a 1941w router. The problem that I am having is that I am unable to ping the switch that is directly connected to it and I am unable to ping from the switch to the router. If I take the address off of vlan 1 and move it to gi0/0.1 the pings work, but then client traffic on the wireless ap inside the 1941w fails.
Here is the releveant config off of the 1941w
version 15.0
no service pad
service timestamps debug datetime msec localtime show-timezone
[Code].....
View 3 Replies
View Related
Jun 5, 2012
im trying to connect a dell MD3000i to a Cisco 3750-s but i am not abel to ping the server.the status is up and Protocol is up. but still nothing.i configerd the port to be a acces port and also at trunk port but still nothing is happening.
View 1 Replies
View Related
Mar 29, 2012
I have the following setup.
host PC (192.168.9.3) -----> gateway (192.168.9.2) ----- Pix E1 (192.168.9.1)/Pix E0 (81.x.x.250) ------ Internet
The 192.168.9.2 gateway is a 3560 switch connected to the PIX. I can ping out to the Internet via IP from the PIX, but not via the host PC (192.168.9.3) on the LAN. PIX and gateway configs below. Am I missing something that's preventing me pinging out to the Internet from the internal LAN?
PIX config
test-cal-pix01# sh run
: Saved
:
PIX Version 8.0(3)
!
hostname test-cal-pix01
enable password btf1YD.Vq7mE6vEA encrypted
[code]....
View 1 Replies
View Related
Dec 14, 2011
i have a site to site vpn stablished, the vpn works fine (while is up), i have a cisco asa 5520 and the other end of the vpn is a jupiter device that for technical reasons needs to send a continuos ping and when it does not receive a reponse back it brings down the vpn tunnel and reestablish it again. while the vpn is up traffic flows perfectly but because i m unable to repond to the ping the vpn is brought down as reestablished by the jupiter device. the jupiter device pings the encryption domain which is an ip that is natted to the real ip in the inside network. this is my configuration of the vpn:
AAA.AAA.AAA.AAA is the ASA public ip in the outside
BBB.BBB.BBB.BBB is the jupiter device ip (part of the object group IP_LIST)
CCC.CCC.CCC.CCC is the nat ip on the ASA
10.21.0.164 is the real address in the inside(code)
View 1 Replies
View Related
Nov 25, 2011
I have 3 2620xm routers connected via dte/dce serial connections In a lab.One of the routers Is also connected to a 2950 switch.
The 2950 switch connects to an unmanaged tp-link switch that Is connected to a dsl modem/router.I have Internet access via the 2950 to my laptop.
I have ripv2 enabled on all the routers and It's working fine.The dsl modem, switch and connected router are on the same subnet.
When I ping the dsl modem via the 2950 or via the router connected to the 2950 , It works 100%.If I ping the 2950 from either of the other two routers , It also works 100%.I can't ping the dsl modem however from the other two routers.I've only been studying for the ICND1 so maybe there's something I'm missing here.
View 4 Replies
View Related
Feb 28, 2011
This is what I have as a setup:BT Home Hub wifi routerPC with Windows 7 Home premium connected via ethernetMacbook Pro with OSX10.6 connected via wifiIt feels like i've tried everything to get this working. As far as I can see the settings are all ok but I've noticed that I can't ping the PC from the mac although I can ping with success the other way around tried traceroute from the macbook and it gives me this so it is able to see it somehow...Code:traceroute to 192.168.1.66 (192.168.1.66), 64 hops max, 52 byte packets 1 alistair-pc.home (192.168.1.66) 1.724 ms * 1.151 msNot sure where to go from here. I think discovering that ping is failing is a good start to diagnose.
View 19 Replies
View Related
Jan 23, 2011
I have a home network of 3 cmputers. DHCP from router. 1 computer is not getting address. But if I assign it one, with same gateway and dns(not a duplicate ip of others), it can ping internally, and outside. I can do tracert to 8.8.8.8 and ping it (google DNS). But I can't get to internet. So - i can get out, but nothing coming in. I have checked firewall.
View 4 Replies
View Related
Jul 27, 2012
i'm configuring the network using static routing from the information above. can i know why i'm unable to ping from pc 1 to pc2 and pc0 to pc2?
View 8 Replies
View Related
Oct 25, 2012
Recently we have configured new site where we are unable to ping global DNS from routers and switches.Checked in the firewall ICMP is allowed.The thing we did is we made Native vlan as vlan 10 (Data vlan ) instead of vlan1. Do this is the issue for not pinging.
View 6 Replies
View Related
Jan 10, 2013
I need another set of eyes on my config. I am trying to set up my router for a basic connection for the time being. I set my gig 0/0 port to dhcp I see traffic being sent and recieved but I can not ping 8.8.8.8. I am connected to a basic comcast modem from 0/0 I have also tried setting gig 0/0 to 100 full. I do have IP routing enabled. I believe I have my acl's configured correctly. I am wondering at this point if I need a static block of IP's from comcast.
hostname vpn-router-2901
username ****** password *****
enable secret *****
[Code].....
View 14 Replies
View Related
Nov 12, 2012
I have 2 routers, one is an Apple AirPort Extreme with a static outside IP address, I also have a Cisco 871 with a static outside IP address. The Airport Extreme connects to a switch on the private network and has an IP address ending in .1. The Cisco 871 connects to the same Private network and it ends in .2. The 871 is setup as a VPN Server. now when clients connect to the VPN they can ping the VLan IP Address on the 871, but they can t ping any other hosts on the smae network. The hosts on the private network can ping the vlan on the 871.
View 7 Replies
View Related
Apr 5, 2013
I have setup 5505 ASA for Testing purposes. It has static route to layer 3 switch on outside interface that goes to the internet.
ciscoasa# sh route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
[Code].....
View 20 Replies
View Related
Dec 1, 2012
I' d like to have some support for a very-basic PIX firewall configuration. I 'm dealing with PIX 515E. Inside hosts can ping inside interface , outside hosts outside interface and so on. Simply i cannot ping outside interface from inside hosts, Inside host-192.168.1.0
Outside - any host like google.com, or to check my isp link's dns ip. I have attached the pix configuration text file to test.
View 10 Replies
View Related
Jun 21, 2012
i have a home lab network that is connected to my internet. I basically have a linksys router connected to cable modem and in order for my families internet to not go down while testing and learning my CCNA I am trying to treat the Linksys as the ISP.
1. Plugged my 891W router via FASTETHERNET 8 (192.168.1.10) into LAN Switch port 1 of my Linksys E4200 home router(192.168.1.1).
2. I plugged my 891W Gigabit 0 (10.10.10.1) LAN side into my 2950 Catalyst Switch (10.10.10.5 - VLAN 1)
3. my 2950 Catalyst switch (10.10.10.5 - Vlan 1) is plugged into my 2600 series router via the routers FE port (10.10.10.2).
There is a few more routers connected behind r2 but I am not dealing with them right now and there is also a switch connected into s1 but its not being used for this.
891w is labled r1
2950 is labled s1
2600 is labeled r2
I am running RIP Verison 2 for my network protocol.
r1 information below
----------------------------
r1#show ip protocols*** IP Routing is NSF aware ***
Routing Protocol is "rip" Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Sending updates every 30 seconds, next due in 24 seconds Invalid after 180 seconds, hold down 180, flushed after 240 Redistributing: rip Default version control: send version 2, receive version 2 Interface Send Recv Triggered RIP Key-chain GigabitEthernet0 2 2 Vlan4 2 2 wlan-ap0 2 2 Automatic network summarization is in effect Maximum path: 4 Routing for
[code].....
I can ping all over my homelab everything I can reach as long as I have a protocol up but I cannot reach the WAN IPs. I watched video by Jeremy Ciorara and I tried to follow the wan and nat part from a website [URL] And none of its working. I am not sure if this is a case where a private IP cannot function as a ISP and I am breaking some rule thats not mentioned in CCNA studies or if its something else. I tried these commands from Jeremy Video:
r1(config)#ip access-list standard "NAT_ADDRESSES"
r1(config-std-nacl)#permit any
r1(config)ip nat inside source list NAT_ADDRESSES interface fastEthernet 8 overload
However they did not work it was pretty close to whats in the basic website up there I listed as well. I think I went back to the basic configuration in the config file post above. Its really frustrating as I follow directions and they do not seem to work. I understand I am using my private 192.168.1.0 subnet as an ISP and maybe that has something to do with it but when yoru first learning and things dont work its kind of overwelming as you have problems seeing the big picture and dont yet trust in things you have learned as they are unfamiliar so its easy to get lost.
View 1 Replies
View Related
Aug 12, 2012
I configured a new Asa 5505 with Ios 8.44-1-k8.bin and when I installed the Asa the client's after about 1 hour were unable to ping or map drives to the Asa. I got the following error,%ASA-2-106007: Deny inbound UDP from XXXX to XXXX due to DNS Query. I added the command same-security-traffic permit intra-interface they were then able to ping the server and connect to the Internet, but still unable to map drives i could see the connections from the Pc's to the server in a show conn with was tcp port 445 with Saa? I reverted back to Ios 8.25 and everything works.
View 2 Replies
View Related
Oct 22, 2012
I have been working on figuring out a VPN problem on my companies ASA5510. I was accessing the device via: ASDM, SSH using Putty, and even initially with a console cable (also using Putty) using a computer in the networking closet. All 3 of these access methods worked properly for me.I believe I may have inadvertently changed something as of Friday using ASDM. I am mostly assuming this because, as of yesterday I can no longer connect to the device. I actually cannot even communicate with it (ping the interface I normally use to manage, which I could previously ping). No computer on the same subnet as me is able to ping the interface. The device is still accepting VPN connections, dishing out DHCP addresses and everything else it normally does, but I really need to be able to gain access to it again. I am thinking to reboot the device when there is some downtime, in the hopes that ASDM doesn't save to startup-config and only to running-config.
View 5 Replies
View Related
Jun 17, 2012
I have installed 2 Cisco 1310's, connecting two buildings that are about 1000 yards apart. One access point is connected to an existing 3560 24 port switch, the other access point has a new 3560 24 port switch connected to it. Also installed 4 1240 access point in the newly connected building to the new switch. Issue is my router and existing switches can not ping any devices on the other side of the bridge. They can ping both access points that make the bridge. I consoled the new switch and could ping the existing switches and router, after doing that the other switches and router are now able to ping the new switch. Now my main issue is I have a user using a 7921 phone connected to one of the new 1242's, when he makes a call to a person in the first building they can hear him, however he can not hear them. Our call manager is in another state were I am located. I can call him and vise versa, and we can hear each other. I have went over my configs server times, and doubled check my IOS versions to make sure they are up to date. I will be glad to provide configs upon request.
View 1 Replies
View Related
Jun 25, 2012
We have had a successful site to site vpn working for several months now. It is an ASA 5510 at HQ to a ASA 5505 at a branch office in another state. We just added a second site to site vpn in another state this time from HQ to a Sonicwall TZ100. After plugging in the Sonicwall to the Qwest modem in bridge mode the tunnel came right up. I was unable to to ping any off the private IPs at HQ from the new branch, but was able to use remote desktop into the servers and workstations at HQ. Also all the computers show up when browsing the network from the new branch.
At the first branch we are able to ping both ways and use remote desktop both ways.When using packet tracer in ASDM on the HQ ASA and pinging from one of the IPs in the HQ protected network to an IP in the new branch network NAT-EXEMPT looks good, but when it hits the first NAT it matches on the "dynamic translation to pool 10 (10.1.255.254) [Interface PAT]" (which is the default route for all the vlans to get to the Internet.)The next NAT (subtype - host-limits) looks better and this one going to the IP address of the outside interface of the HQ ASA 5510, but then the third NAT (Subtype - rpf-check) reverts back to the "10 (10.1.255.254) Interface PAT]" and the packet is DROPPED. Also there is no VPN step in Packet Tracer after NAT.[code]
Is the problem possibly due to the fact that my 2 new ACLs for "encrypt_acl-30" fall after "access-list global_mpc extended permit tcp any any" in the config and it is running into the implicit deny all?
View 8 Replies
View Related
Jan 31, 2011
I have to sites connected togather using 4 MBps Link over the tunnel terminated on asa 5510,the call manager in site 1 and the other users on the site 2 unable to register with call mamager on site while i have a suceesull ping goes from site 2 to site 1 (call manager ip) so why this phone its not registered ,so in term of network no problems coz the ping gets through and am rely on ping to confirm that no network problem
----is there any udp traffic problem that prevent the phone registration
View 20 Replies
View Related
Mar 1, 2010
I have a 1760-v router set up at my home lab and I am unable to access IP addresses outside my local network. I have my Cisco router's fast Ethernet port connected to a small net gear router which then connects to my cable modem. The Cisco router is able to ping local address fine, but when I try to ping an outside address or domain name it times out. However, when I am at the CLI and type something like Ping { URL}, it resolves Google's IP address but it will not ping it. I have IP DEFAULT-GATEWAY and IP NAME-SERVER both pointing to my net gear router and pointing to my ISP's DNS server.
View 3 Replies
View Related
Jan 13, 2012
I have two windows 2008 machines on vmware. I assign 10.0.0.1/8 and 10.0.0.2/8 to them. Both connected to same virtual switch. Now should these two PCs ping each other? In my case they dont ping. What i get is Repy from <ip address>: Destination host unreachable.
View 2 Replies
View Related
May 12, 2011
unable to access or ping google.com on WinXP - have two computer side by side. only having the problem on one of them. Have replaced the network card, did have malware but cleaned it up with malwarebytes.
View 1 Replies
View Related
Jul 11, 2011
I'm trying to setup my home network so that I can access it when away from home but I've ran into problems and I can't figure out what is causing the problem.I've setup the router to forward incoming requests on port 80 to be directed to my PC running WAMP. The PC has a static IP and if I access it from another PC on my network I get the WAMP page load as expected.I've also setup an account with no-ip.com to resolve my (dynamic) ip. If I use the address they have setup while I'm on my network I get the login page for the router, again this is what I expect.The problem begins when I try and access my home address (whatever.no-ip.biz) from outside my network. I've tried it from 2 different locations and via a dial-up account and I get nothing.
View 6 Replies
View Related
