Configuring Network - Unable To Ping PCs
Jul 27, 2012i'm configuring the network using static routing from the information above. can i know why i'm unable to ping from pc 1 to pc2 and pc0 to pc2?
View 8 Replies
ADVERTISEMENT
Cisco Application :: Configuring Load Balancer (ACE 4710) - Unable To Ping VIP
May 13, 2013I have trouble with new installation LB ACE 4710 for Oracle application load balance. Problem: Unable to PING VIP - 10.11.10.55 / 24
Below are the simple configuration parameters:
1. ACE 4710 is connected with Cisco 3560 Switch - L2 Trunk (Channel Group)
2. Cisco 3560 Switch is connected with Cisco 6500 Switch (Core) also L2 Trunk
3. There are 3 Vlans,(255, 310, and 370), Vlan 255 is management Vlan
4. Real Servers and Virtual IP are part of Vlan 310
- VIP - 10.11.10.55
- Real Server1 - 10.11.10.46
- Real Server2 - 10.11.10.47
5. Gateway is 10.11.10.1 (vlan 310), 10.11.70.1 (Vlan 370)
Home Network :: Unable To Ping Static Ip From Outside Campus
Nov 7, 2012I have 5 Static Ip pool all IPs are working fine. I have deploy a IIS Server on Windows2008 and configure the Static IP on that server. earlier it was working fine . but since last month the IP is not pinging from Out Side but internal IP Pool its working. I have checked the SERver firewall and another Setting is Ok. if i changed the Ip from the server the new IP is also not pinging.
View 1 Replies View RelatedCisco Routers :: ASA5520 - Unable To Ping From Corporate Network
Sep 14, 2012I have created an IPSEC VPN tunnel using a Cisco ASA5520 (corporate) to a Cisco SRP541W (remote). The corporate subnet is 10.1.0.0/16, and the remote subnet is 192.168.1.0/24. From the remote subnet, I can ping anything on the 10.1.0.0 corporate network, but I cannot ping from the corporate network to the remote subnet. At first I thought this was something obvious, perhaps an incorrect acl or something easy on the corporate firewall. However, we have several other vpn tunnels established, all set up the same, and they work just fine. After looking at it a bit more closely, if I ping the remote subnet I see the hit counter increment by one each time, which leads me to believe that traffic is in fact being routed properly.Now I'm thinking that something in the remote SRP541W that is not allowing icmp traffic, but I can't find it anywhere. To be honest I have never used this type of firewall before, they have all been Cisco PIX501/506e and ASA5500 models.
View 2 Replies View RelatedCisco Wireless :: Unable To Ping Pc On Same Network Through 857w Router
Feb 13, 2012I am missing something and i dont no what but i am trying to ping a pc on the same network but get a destination host is unreachable. Can any one think of anything that could be causing this, i can ping the default gateway and internet address's?
!
interface FastEthernet0
no cdp enable
[Code].....
Home Network :: Remote Ip Address Is Updating DNS Server But Unable To Ping It?
Apr 20, 2011i have a new smc router and my local ip address and remote ip addresses are very similar. The remote ip address is updating my dns server but i am unable to ping it. Its something like 122.61.xxx.1 ?
View 8 Replies View RelatedCisco VPN :: SA520 / Unable To Access Network Shares / Impossible To Ping
Apr 23, 2013I would like to setup a VPN to allow employees nomad that connect to our network from outside. Our router is a Cisco SA520 I tried different configurations without success ...Here is the current VPN configuration:I created my users IPSec, I can connect remotely, but I do not have network access ... Unable to access network shares, impossible to ping.
View 1 Replies View RelatedCisco Firewall :: ASA 5512-X / VPN Client Is Connected But Unable To Ping Internal Network
Mar 17, 2013I have created a VPN connection for ASA 5512-X by using the wizards and nothing seems to be wrong on the wizards's config.I am able to connect to the network by using the VPN but unable to ping internal network.Below is my config for your reference:
Result of the command: "sh run"
: Saved
:
ASA Version 8.6(1)2
!
hostname FAA-ASA-1
enable password crzcsirI44h2BHoz encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
[code].....
Cisco Switching/Routing :: 4.2.2 Unable To Ping 1 Internet Site From Edge Router Able To Ping
Jan 18, 2013From My Router that connects to Cable modem i am unable to ping website 4.2.2.2I am able to ping all other websites fines.Same website i can ping from my pc and all other switches fine.Router has only 1 ACL thats for NAT.
View 25 Replies View RelatedCisco Routers :: Rv042 Quick VPN Windows 7 Unable To Access Network Shares Or Ping
Nov 26, 2011I have an RV042 using Quick VPN to connect to a remote network. I have port 1723 forwarded to a static IP address on a Windows 7 Pro 64 bit PC. I can establish the VPN and ping a printer but not the Win 7 PC. I can not acccess any shares on the pc via the IP address. It has Norton Antivirus and Windows Firewall. This remote PC replaced a Windows xp PC that allowed access to the shares. I have tried access with a Windows XP Pro and Windows Vista Home Premium PC. Neither have worked.
View 1 Replies View RelatedCisco WAN :: 2911 - Site-to-site IPsec Vpn / Unable To Ping Remote Network
Apr 3, 2013I have two Cisco routers - 2911 in HQ and RV180 in branch office. Because in HQ LAN network I have some development servers, to which guys from branch office need to have acces, I decided to setup VPN site-to-site between HQ and branch office. Everything went quite smoothly, on both devices I see, that ipsec connection is established. Unfortunately I am not able to ping resources from one network to other one and vice versa. Below is the configuration of 2911 router (I skipped som unimportant (imho) configuration directives) :
crypto isakmp policy 1
encr 3des
hash md5
[Code].....
Cisco VPN :: Configuring L2TP IPSEC VPN On ASA 5505 / Can’t Ping Or Access Resources
May 2, 2011I’m configuring a L2TP IPSEC VPN on a 5505 asa so that windows 7 clients can natively connect. It connects correctly during Phase 1 and 2, but I can’t ping anything or access resources on the internal network. This is my first time working with an ASA.
Master# sh run
: Saved
:
ASA Version 8.2(2)
!
hostname Master
domain-name service.local
[code]....
Unable To Connect To The Internet Wirelessly After Configuring A Range Extender?
May 28, 2011I recently configured a linksys range extender to my modem and since doing that, I'm getting a message stating that there is an IP address conflict with another system on the network. When I set up the range extender, I assigned an IP address to it that was different from the modem but yet this message still appears. Also even though my wireless connection is connected, I'm unable to connect to the internet - I keep getting the message 'internet explorer cannot display webpage'.
View 3 Replies View RelatedCisco :: Unable To Ping In Dos?
Mar 9, 2013*I have 2 cisco routers 2811 router A&B*using 0/0 for WAN and 0/1 for LAN on both routers*both routers are connected together with crossover cable to 0/0. recieve link and activity*both routers are on the same subnet Router A:0/0 192.168.1.1/24 - router A:0/1 192.168.2.1/24 ; Router B:0/0 *192.16.1.2/24 router B:0/1 192.168.3.1/24*I can ping the inside and outside address of both router from PCs connected at its respectable end. *PC A 192.168.2.2/24 PC B 192.168.3.2/24 *when connected to router A 0/1 and I try to ping router B 0/0 it times out in DOS* but I AM (CAN) able to ping from PC A to router B 0/0 in hyperterminal, telnet and Cisco SDM. I just CANNOT ping in DOS?
View 10 Replies View RelatedUnable To Ping Any System In LAN?
Mar 9, 2011We have many CT/MRI etc. machines and Servers in the Hospital LAN. Now intermittently we are loosing the LAN connectivity i.e we are not able to ping any system from any node inside the hospital network for sometimes, after some time it will start working and then again it will stops again.We are using procurve switches and also we are not using any router
View 2 Replies View RelatedUnable To Ping From One Another With OS XP And Windows 7
Sep 14, 2012I m not able to ping from one to another with the os win XP n other with win 7.
View 1 Replies View RelatedD-Link DIR-615 :: Unable To Ping It
Jul 29, 2011I'm trying to do port forwarding on my DIR-615...first of all I need to be able to ping the router from outside! I did enable the ping options to allow request from WAN...still don't work!!I removed the router and plug my laptop directly on my cable modem adapter and I'm able to ping my IP address (did put the same address the router had)...so, the IP is OK and it is possible to get in the modem from outside.I did plug back the router, and still not working...I did some trick like enable all IP with the Inbound filter...give access to few MAC address that I have to give more chances to get in and still not working!!!
View 6 Replies View RelatedCisco :: Unable To Ping Over Ipsec VPN?
Mar 25, 2011I have created a site to site Ipsec vpn with a cisco 2610 and a linksys RV042. Running a show "crypto isakmp sa" command I get a qm_idle status and when running a "show crypto ipsec sa" I see that packets are being decrypted and encrypted. Also when running the "show ip access-lists" command I do have matches to that connection.The problem is that I am unable to ping hosts from one network to another. For example, from the Cisco router in network 192.168.0.0 I am unable to ping the remote network 192.168.2.0 and vice versa.
I am not sure what is happening. Do I need to create a route to that remote network? I guess it could also be a problem with NAT or an ACL.Here is what running-config shows:
crypto isakmp policy 1
encr 3des
hash md5
authentication pre-share
group 2
lifetime 28800
Cisco :: Unable To Ping From Static IP?
Oct 26, 2012I am connecting a 2600 router to an ISP. Interface 0/0 is connected to the ISP using DHCP. Interface 0/1 is connected to the inside providing DHCP services to the inside. At least it should only be providing DHCP services to the inside. I also have a public static IP that is NAT to a private static IP. Everything is working except the computer on the static IP. From the router I am able to ping inside and out from each interface. I am able to ping both interfaces of the router from the computer on the static IP but I cannot ping outside the router. If I do a debug all I see a reject for the gateway of the static IP but it has “mobile IP” in the text string. Not sure what mobile IP is relating to. Networks are as follows:
0/0 DHCP 10.X.X.X
0/1 192x.x.x
Static 75.X.X.X
[Code].....
Unable To Ping Windows 7 Machine On LAN?
Feb 28, 2011This is what I have as a setup:BT Home Hub wifi routerPC with Windows 7 Home premium connected via ethernetMacbook Pro with OSX10.6 connected via wifiIt feels like i've tried everything to get this working. As far as I can see the settings are all ok but I've noticed that I can't ping the PC from the mac although I can ping with success the other way around tried traceroute from the macbook and it gives me this so it is able to see it somehow...Code:traceroute to 192.168.1.66 (192.168.1.66), 64 hops max, 52 byte packets 1 alistair-pc.home (192.168.1.66) 1.724 ms * 1.151 msNot sure where to go from here. I think discovering that ping is failing is a good start to diagnose.
View 19 Replies View RelatedUnable To Access Internet But Able To Ping?
Jan 23, 2011I have a home network of 3 cmputers. DHCP from router. 1 computer is not getting address. But if I assign it one, with same gateway and dns(not a duplicate ip of others), it can ping internally, and outside. I can do tracert to 8.8.8.8 and ping it (google DNS). But I can't get to internet. So - i can get out, but nothing coming in. I have checked firewall.
View 4 Replies View RelatedCisco WAN :: 2911 Unable To Ping From LAN To WAN
Apr 26, 2012I have the following setup where the Cisco ME 3400 provided by the ISP.
My Cisco 2911 is configured as below:
CORE_Router#sh run
Building configuration...
Current configuration : 6075 bytes
[Code].....
Cisco VPN :: ASA 5505 - Unable To Ping Or Use DNS On LAN
Aug 18, 2011I've been called upon to fix the SSL VPN issues in our ASA5505. The issue I am having is that I am able to log into the vpn, access the internet, but I'm unable to access anything on the LAN. I can't use ping or use DNS.
I'm using ASDM v. 6.2(1) and ASA verison 8.2(1). I'm not comfortable using the CLI and prefer the GUI.
Routers / Switches :: Two PCs On Same Switch Unable To Ping Each Other
Jan 13, 2012I have two windows 2008 machines on vmware. I assign 10.0.0.1/8 and 10.0.0.2/8 to them. Both connected to same virtual switch. Now should these two PCs ping each other? In my case they dont ping. What i get is Repy from <ip address>: Destination host unreachable.
View 2 Replies View RelatedBroadband :: Unable To Goto Or Ping Google
May 12, 2011unable to access or ping google.com on WinXP - have two computer side by side. only having the problem on one of them. Have replaced the network card, did have malware but cleaned it up with malwarebytes.
View 1 Replies View RelatedUnable To Ping External Home Ip And No Access?
Jul 11, 2011I'm trying to setup my home network so that I can access it when away from home but I've ran into problems and I can't figure out what is causing the problem.I've setup the router to forward incoming requests on port 80 to be directed to my PC running WAMP. The PC has a static IP and if I access it from another PC on my network I get the WAMP page load as expected.I've also setup an account with no-ip.com to resolve my (dynamic) ip. If I use the address they have setup while I'm on my network I get the login page for the router, again this is what I expect.The problem begins when I try and access my home address (whatever.no-ip.biz) from outside my network. I've tried it from 2 different locations and via a dial-up account and I get nothing.
View 6 Replies View RelatedUnable To Ping Or Connect To Remote Desktop On Xp Pro Sp3
Jun 11, 2011I have two computers side by side 192.168.1.7 and 192.168.1.8 both running xp pro sp3. On 8 I can RDC to the 7, but on 7 I cannot RDC to 8. I can see port 3389 listening on both using netstat -a. But 7 just can't RDC connect to 8. 7 cannot ping 8 either. I have the firewall turned off on 8, I had tried allowing RDC 3389 earlier with the firewall but that didn't work either.I don't have any extra firewalls running.Life will be like perfect, if I can just RDC to 8.Both are on the same wired belkin wireless router, 4' from itl.I tried taking the no ping no rdc computer to work and it didn't work there either.
View 19 Replies View RelatedUnable To Access Facebook - Ping Timing Out
Aug 2, 2011It works on the mobile site at times maybe twice a day but only able to access for 10 minutes maximum. I tried the command prompt and ping facebookm and noticed that I didnt recieve files back and it was just timing out is that whats causing it?
View 3 Replies View RelatedUnable To View Websites - Able To Ping Sites
Dec 22, 2012I have been accessing my webmail account everyday for the past 3yrs with not problem until this week. Stopped working mid week. No changes to computers. Have 3 and none will access this site any longer. Just times out. Sometimes I can ping and other times not. Can log onto other networks and access with out any problems. My ISP says it is not their problem. (Site is [URL]).
View 1 Replies View RelatedUnable To Ping Public IP Of 3G Router From Internet
Apr 3, 2013I have just setup the 3G Wifi Router (Huawei 3G21WE) for my company at remote site for temporary use.Now we want to monitor the DVR and cameras installed on the site from head office but i am unable to do it.I have done the port forwarding on the router and using Dyn DNS and configured it correctly, but i cannot browse it from internet.I have also noticed that i am unable to ping the public IP/DynDNS from internet. also i cannot find any option to disable the firewall on my router.
View 3 Replies View RelatedBelkin F5D8236-4 - Unable To Ping Router
Sep 6, 2011O.S - Windows Vista
Router - Belkin F5D8236-4
When I check with PFPortChecker, it says "We were not able to ping your router" I have done everything correctly, or maybe I thought I have. I have try 69.165.255.1 a default gateway but it just goes to Unidentified Network and I can't access the Internet
D-Link DIR-655 :: Unable To Ping External IPs When Used As Wireless AP
Mar 14, 2013Both my DIR-655 and DIR-815, when setup as wireless access points, are unable to ping external IP addresses and thus cannot contact the dlink ntp servers. I've disabled UPnP, disabled DHCP, changed the LAN IP address to an available address on the network. The wireless works, devices are getting an IP from the network DHCP server and can surf the internet. But the DLink router itself cannot ping any external IP addresses. But the DLink router itself cannot ping any external IP addresses.
View 3 Replies View RelatedCisco Firewall :: ASA 5505 Unable To Ping
Sep 9, 2011I just tried to configure my ASA but unable to ping. My setup is as follows:
Cable Modem (DHCP from IPS)---> ASA (192.168.1.1)--->Belking Router (192.168.5.1)--->Switch (192.168.5.14)--->
ASA Version 8.2(3)
!
hostname WoodHomeASA-1
[Code].....