I would like to setup a VPN to allow employees nomad that connect to our network from outside. Our router is a Cisco SA520 I tried different configurations without success ...Here is the current VPN configuration:I created my users IPSec, I can connect remotely, but I do not have network access ... Unable to access network shares, impossible to ping.
View 1 RepliesI have an RV042 using Quick VPN to connect to a remote network. I have port 1723 forwarded to a static IP address on a Windows 7 Pro 64 bit PC. I can establish the VPN and ping a printer but not the Win 7 PC. I can not acccess any shares on the pc via the IP address. It has Norton Antivirus and Windows Firewall. This remote PC replaced a Windows xp PC that allowed access to the shares. I have tried access with a Windows XP Pro and Windows Vista Home Premium PC. Neither have worked.
View 1 Replies View RelatedI have a site-to-site VPN (no client software) that is up and I can ping all the IPs on the other side.
My computer is connected to .2.0, remote LAN is .1.0
I can view all of the local LAN (.2.0) devices in Network Location, but can't access the shared resources on the remote .1.0 LAN.
ServerFolder shared directories is mapped as a drive and worked yesterday. It now has a red X on in and I can't access it, but can ping \Server's IP address.
I'm currently configuring an ASA5510.I connected a laptop (IP 192.168.96.18/255.255.255.0) to port 0/2 and tried to ping 192.168.100.2 ... impossible to ping outside interface.I resetted the config of the ASA to retest more simple. [code]
View 1 Replies View RelatedUpon attaching my external storage I was able to create a share, copy files and access it successfully from everywhere. Now when I attempt to add an additional share, the router lets me create it but when I try to move access groups over from the available groups, the >> buttons are greyed out. The one working share has the admin and Everyone groups with access. Any additional share I create has the admin group in it by default, but I can't add any more groups. I am logged into the router as admin and logged into the pc as a local admin. I am also unable to change the rights from my pc on a share (access denied). I AM, however, able to map a drive to a new share successfully, but when I copy files over, a few minutes later the filenames are there but they show up as 0 byte files.
View 7 Replies View RelatedThey can connect to the VPN and I can see incoming connections, but they can't access network shares. I mean they don't see them, and in network connections it says NO INTERNET CONNECTION.
View 1 Replies View RelatedI am currently trying to configure a Remote Access VPN on a SA520 (Primary Firmware Version 2.1.51) using Cisco VPN Client (Ver 5.0.07.0410)
Until now i have connectivity from the SA to the LAN and i can connect using the Cisco VPN Client to the AS:
[IKE] INFO: IPsec-SA established[UDP encap 12856->4500]
[IKE] INFO: IPsec-SA established[UDP encap 12856->4500]
It gives me an IP from the pool but i can not reach through ping to my LAN.
I`ll get straight to the point. I have at work a domain of computers. on one of the computers (I have admin rights) I want to share a folder that can be accessed by other computers that are not in the domain. By default accessing that share requires a user/pass. My question is: can I configure something on the computer (running windows 2008 server) to the shared folder so that other computers that are not from the domain will gain access to without user/pass requirement (like a normal share)?
View 3 Replies View RelatedI replaced my old Linksys WRT54G wireless router with the new E3000 wireless router. The installation was a breeze, but not what followed henceforth. I was able to access the internet on my wireless desktop/laptop/Netflix ROKU player/WD TV live media player, but lost access to all the network shares. I spent a lot of useless time with Linksys chat support and phone support, where they said their responsibility is only getting the internet working. They said they are not responsible for file and printer sharing issues, and suggested I use a third-party paid support package to resolve my issues. Over and above spending a hefty amount for the lates top of the line E3000 router, I was not going to shell out additional money for support.
Thinking that it could probably be due to some Windows XP firewall/anti-virus (McAfee) issues, I disconnected the E3000 and connected the old WRT54G back again. Lo and behold, everything started working fine again. I could access the shared folders of my desktop (to which my router is attached) and printer, from the wireless laptop/desktop/media player just as before without any problems. I then switched back to the E3000 and lost the shares again. So I have come to the conclusion, there is definitely some setting within the E3000 that is preventing the file and printer sharing. I just can't figure out what it could be, and am at a point of returning it back to the store as defective. The extra N-speed is useless to me if my devices can't access the network shared content.Also, I tried to set up the UPnP media server feature of the E3000 by attaching USB storage and configuring it via the Linksys web based utility, but my media player is unable to access the content.
My company is using an RV016 router as a gateway to our internal network. My end goal is to allow remote users to access network shares via Samba.I've been trying to create a VPN using the router with absolutely no luck. I've tried QuickVPN. I've tried creating a client-to-site group vpn. I've tried creating a client-to-site tunnel vpn. I've tried pptp. Nothing will allow me to establish a VPN connection. Sometimes there is information logged in the router but most of the time there is not.
View 1 Replies View RelatedI have a network with 2 WRT54Gs in it. One in the besement connects to my cable modem and serves as a gateway and DHCP server as well as a wireless access point. That WRT54G is perfectly accessible. I have another in my room set up as a router and access point only, connected by its ethernet port to the gateway. This one proves a bit trickier. Thet network works flawlessly, and if I couldn't see it sitting right there I would doubt it even existed. I can't ping it (I forgot the IP but tried all the ones that seemed logical), it doesn't show up in my network map, etc. From what I gather that's how a switch is supposed to work. But since this is also a managed router, I would think there should still be some way to connect to it to administer it. How can I log in to this router to change settings if I need to?
I'm not sure if maybe 192.168.2.0 is the other router or if that's some kind of special address (My network is on the 192.168.2.* subnet, don't even ask why...). I've seen it in other posts about routing tables but they all had it routing to 0.0.0.0 instead of the router's own IP. I tried pinging 192.168.2.255 and got no responses at all, not from any computers or from either of the routers, so that was not useful. Tracert from my computer to the gateway doesn't show the router (my computer connects to the gateway through the router).
I have a Windows 7 machine sending shares across the network. Other Windows 7 machines have no problems connecting, but XP machines cannot connect. (Win7 can connect to XP shares).
I have adjust every setting that I have seen to no avail. This includes turning off HomeGroups, turning off password. Removing my password from my user account. Adding "Everyone" to each of the shares. I have even messed with the Local Group Policy Editor to send unencrypted passwords to third party SMB's.
I am unable to isolate DMZ and LAN traffic with an SA520 running 2.1.7.1 firmware. I have the optional port configured as DMZ and DHCP server enabled. I tired leaving the firewall as default. Also tried creating firewall rules to deny traffic from LAN to DMZ and DMZ to LAN for any address and any service.I am still able to ping devices both from LAN to DMZ and DMZ to LAN. I am also able to see network resources in both directions.
View 5 Replies View RelatedI have a home network of 3 cmputers. DHCP from router. 1 computer is not getting address. But if I assign it one, with same gateway and dns(not a duplicate ip of others), it can ping internally, and outside. I can do tracert to 8.8.8.8 and ping it (google DNS). But I can't get to internet. So - i can get out, but nothing coming in. I have checked firewall.
View 4 Replies View RelatedI have been working on figuring out a VPN problem on my companies ASA5510. I was accessing the device via: ASDM, SSH using Putty, and even initially with a console cable (also using Putty) using a computer in the networking closet. All 3 of these access methods worked properly for me.I believe I may have inadvertently changed something as of Friday using ASDM. I am mostly assuming this because, as of yesterday I can no longer connect to the device. I actually cannot even communicate with it (ping the interface I normally use to manage, which I could previously ping). No computer on the same subnet as me is able to ping the interface. The device is still accepting VPN connections, dishing out DHCP addresses and everything else it normally does, but I really need to be able to gain access to it again. I am thinking to reboot the device when there is some downtime, in the hopes that ASDM doesn't save to startup-config and only to running-config.
View 5 Replies View RelatedI'm trying to setup my home network so that I can access it when away from home but I've ran into problems and I can't figure out what is causing the problem.I've setup the router to forward incoming requests on port 80 to be directed to my PC running WAMP. The PC has a static IP and if I access it from another PC on my network I get the WAMP page load as expected.I've also setup an account with no-ip.com to resolve my (dynamic) ip. If I use the address they have setup while I'm on my network I get the login page for the router, again this is what I expect.The problem begins when I try and access my home address (whatever.no-ip.biz) from outside my network. I've tried it from 2 different locations and via a dial-up account and I get nothing.
View 6 Replies View RelatedIt works on the mobile site at times maybe twice a day but only able to access for 10 minutes maximum. I tried the command prompt and ping facebookm and noticed that I didnt recieve files back and it was just timing out is that whats causing it?
View 3 Replies View Relatedi'm configuring the network using static routing from the information above. can i know why i'm unable to ping from pc 1 to pc2 and pc0 to pc2?
View 8 Replies View RelatedI have created an IPSEC VPN tunnel using a Cisco ASA5520 (corporate) to a Cisco SRP541W (remote). The corporate subnet is 10.1.0.0/16, and the remote subnet is 192.168.1.0/24. From the remote subnet, I can ping anything on the 10.1.0.0 corporate network, but I cannot ping from the corporate network to the remote subnet. At first I thought this was something obvious, perhaps an incorrect acl or something easy on the corporate firewall. However, we have several other vpn tunnels established, all set up the same, and they work just fine. After looking at it a bit more closely, if I ping the remote subnet I see the hit counter increment by one each time, which leads me to believe that traffic is in fact being routed properly.Now I'm thinking that something in the remote SRP541W that is not allowing icmp traffic, but I can't find it anywhere. To be honest I have never used this type of firewall before, they have all been Cisco PIX501/506e and ASA5500 models.
View 2 Replies View RelatedI am missing something and i dont no what but i am trying to ping a pc on the same network but get a destination host is unreachable. Can any one think of anything that could be causing this, i can ping the default gateway and internet address's?
!
interface FastEthernet0
no cdp enable
[Code].....
Two computers on the home network:Dell desktop running Vista (computer name PJ) is wired to a Belkin routerThinkPad laptop running Win7 (computer name ThinkPad) connected wirelessly to routerThe desktop (PJ) can see the laptop (ThinkPad) and access it's shares.On the laptop the desktop name (PJ) shows up under NETWORK but clicking on the computer name shows: "Windows cannot access \PJ"I have turned off Windows Firewall and AVG anti-virus on PJ but CANNOT ping PJ from ThinkPad[CODE]
View 18 Replies View RelatedI have 5 Static Ip pool all IPs are working fine. I have deploy a IIS Server on Windows2008 and configure the Static IP on that server. earlier it was working fine . but since last month the IP is not pinging from Out Side but internal IP Pool its working. I have checked the SERver firewall and another Setting is Ok. if i changed the Ip from the server the new IP is also not pinging.
View 1 Replies View RelatedI want to use Cisco VPN Client to VPN to my SA520 to manage a UC320W. I can establish a VPN connection to the SA and ping both the SA and a switch that I have on the network, but I cannot ping my UC. I've set up firewall rules to allow ANY-ANY access from LAN-WAN, and a WAN-LAN rule to allow a certain range of IP addresses (the IP addresses assigned from the VPN DHCP pool, in this case, 192.168.12.x) access to the UC.
My SA IP address is 192.168.75.1 and my UC is 192.168.75.2 (I can ping both when I am directly connected to a LAN port on either equipment).
I'm trying to configure a VPN remote access type on a SA520-k9 but i don't know why doesn't work.
My Internal network is 192.168.131.0/24 and my Wan Ip is 87.216.xxx.xxx.
on Remote WAN's IP Address / FQDN i put the WAN IP 87.216.xxx.xxx on Local WAN's IP Address / FQDN I put the cisco SA520 Ip. I think this is the problem.
I create a IPsec user. I create a firewall rule from WAN interface to SA520 Ip with IPSEC-UDP-ENCAP service.
I have created a VPN connection for ASA 5512-X by using the wizards and nothing seems to be wrong on the wizards's config.I am able to connect to the network by using the VPN but unable to ping internal network.Below is my config for your reference:
Result of the command: "sh run"
: Saved
:
ASA Version 8.6(1)2
!
hostname FAA-ASA-1
enable password crzcsirI44h2BHoz encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
[code].....
I have a PPTP VPN setup in RRAS on Windows SBS 2008.
The VPN seems to works fine, I can ping everything on the other end of the tunnel. RDP into workstations, access shares on the workstations. I can telnet into the exchange server and send mail. Get the default IIS page at http://server.
From the SBS I could even map shares I have on my local workstations, but when I try to access any of the shares on the server over the VPN using hostname or IP it fails, "The network path was not found".
Not really sure whats going on here, I've shut the firewall off without success. I reconfigured the VPN from scratch and rebooted the server and it didn't change a thing. I'm unsure how long this has been like this since no one uses the VPN to access file shares on the server. The few that use it just RDP into their workstations, no issue there. Though recently they started replacing a few desktops with laptops and they have nothing to RDP into, they only need access to a few spreadsheets while at home or on the road so I thought the VPN would work, I guess not..
i have a new smc router and my local ip address and remote ip addresses are very similar. The remote ip address is updating my dns server but i am unable to ping it. Its something like 122.61.xxx.1 ?
View 8 Replies View RelatedFrom My Router that connects to Cable modem i am unable to ping website 4.2.2.2I am able to ping all other websites fines.Same website i can ping from my pc and all other switches fine.Router has only 1 ACL thats for NAT.
View 25 Replies View Relatedi purchased vaio with win8. Under network icon, I can not see any other computers in the local network therefore not able to access shares unless i explicitly map the shares which is tedious.
On other computers running win7 and xp, each of them can see each other under network icon.However that is not the case with my laptop running 8. Actually i have seen once or twice all pc-s show up but most of the time, they dont appear.
I read somewhere that following service need to be checked to make sure they are running: upnp, ssdp in services. I checked those and they are all running.
I also enabled "turn on network discovery" under network and sharing->advanced sharing. setting. To make it more complicated there are private and public and all network setting. I enabled all items as follows:
1. Private Turn on network discovery is checked along with Turn on automatic setup of network connected devices Turn on file and printer sharing is selected Allow Windows to manage homegroup connections is selected.
2. Guest or public Turn on network discovery is selected Turn on file and printer sharing is selected.
With these settings I still dont see the local computers and their shares. Do I need to check anything else?
Ive just updated my hardware including hard drves, and now I have a couple of redundant shared folders showing on the network trees (in my file manager) How do I delete these obsolete shared folders that dont exist?
View 2 Replies View RelatedI am finally switching over my work computer from Windows XP to Windows 7. I have multiple network connections I connect to when I boot up. I've set myself as a new user on the servers I have to connect to, Windows 7 asked me to put in my username and password for each share, all connects fine but when I shutdown and restart, I see all my Shares as red x'ed "disconnected" and as I click on each one, I have to put in my username and password again. Windows XP always remembered my connections and logged me onto each share at boot up. I've checked "remember my credentials" but it's not doing it, Am I missing something? on any restart or shutdown, I have to click on each share and put in my login credentials.
View 1 Replies View RelatedI recently did a clean install of Win 7 64-bit Pro on my workstation. This was previously connected to my DNS (Windows server 2008 R2) which i use to host my files, music etc for my home network. I was previously able to see my network shares in windows explorer (client side) but now I don't. If i go to search box and \server the shared folders will then be displayed in windows explorer under network and i have access to them. I've done a small amount of digging but have so far found nothing to point me in the right direction. So while i have access i would like to be able to point windows media player to my shared music on the server, which i can't do now because I have no way to navigate to that folder. Same with other programs such as outlook, when i want to attach a file to an email i'm not able to navigate to the share. Weird as i have access to the share by search \server?
View 3 Replies View RelatedI have 3 or 4 devices connected via a wireless connection, 2 of which are in the same room. Roughly a week ago, my desktop (Vista OS) started to suffer from severely reduced download speeds (5-30kb/s), while my laptop (also Vista OS) which is on the same wireless network continues to run at normal speeds (500kb/s-1mb/s).
I have tried a system restore, scanning for viruses, updating/disabling antivirus and firewalls, connecting directly to LAN, changed wireless interface speed from g to b to mixed, changed wireless channels from 1-6-11, nothing seems to work.
I have a Thomson TG782T router with a D-Link wireless card (which is rather old).