Cisco Infrastructure :: Can 3600 Support IP Addresses And VLANs And How
May 6, 2012
I am working on my CCENT after getting my A+. I have an old 3600 router and I am following CBT Nuggets to configure it. CBT Nuggets seems to have an IOS that supports VLAN and IP Addresses and it looks like mine only goes up to Token Ring so it doesn't mirror the instruction. I know it's an old router but is there a software release (like the 12.4 maybe?) that would allow me to follow the CBT Nuggets more accurately so that I can set the switch up for IP Addresses and VLAN instead of limiting me to token ring?
View 1 Replies
ADVERTISEMENT
Nov 27, 2012
On an 887VA running 15.x IOS, is there a way to support both public and private addresses on inside vlans? The outside interface is public static ip, so the requirement would be to not nat anything if coming from inside vlan10 but nat if coming from inside vlan20.I didn't think this was possible since the outside interface would have to use an outside nat command that would not be ignored for traffic coming from vlan10.
View 4 Replies
View Related
Nov 4, 2012
I have a router 3600 with a power connector kind RPS but I don't have a RPS system, Do it exist a kind of wire that I can connect directly from my router to AC?
View 1 Replies
View Related
May 2, 2012
We are deploying 3600 AP's with a 2504 and would like to create multiple SSID's that are mapped to unique VLANs so we can control the traffic at the Firewall. We have the 2504 up and running with AP's but there appears to be no where in the 2504 controller Web GUI to configure a VLAN mapping to an SSID. Any pointers to documentation on how to configure?
View 1 Replies
View Related
Feb 13, 2012
Does cisco 3600 support office extend feature? If yes, is there a controller requirement? I know cisco AP 600 supports office extend
View 24 Replies
View Related
Oct 23, 2012
I noticed that the 3600 access point series will get an add-on module to support 802.11ac. This standard will support more than 1 GBit/s.But the 3600 series still do only have got one GBit port. Any extended information about 802.11ac in the upcoming Cisco portfolio?
View 8 Replies
View Related
May 7, 2013
I am in the process of implementing 750 Cisco Access Points acros the business. I need to make a note of the serial numbers and Mac addresses for our inventory before I get these configured and sent out to their relavent destinations. The AP's have have arrived in boxes of 10 (75 boxes). The sticker on the box with the barcode is either covered with a postage sticker, ripped, or my scanner will not scan it becaise it is too small. There is a sticker with the serial bundle which is larger and therefore scanable. Is there a way that I can scan this and get the MAC address and serial number.
I know that this is not a technical question but I don't want too spend the next 3 weeks opening 75 boxes and removing each AP individually and recording it.
View 4 Replies
View Related
Dec 26, 2012
I am trying to setup my 3550 layer 3 switch to do hand out dhcp addresses for different vlans. It is connected to my router address 192.168.1.1. I setup a new vlan 3 and the dhcp pool.. The client gets a 192.168.3.2 address but am not able to ping the router and other clients and get out to the internet.
Here is the config that I have. I deleted the other ports because I am not using them. The vlan 3 client is on port fast Ethernet 0/17 and the router is connected to the fastethernet 0/1.
version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
[code]....
View 12 Replies
View Related
Jan 20, 2013
We have a data center with servers set up for different projects, some servers from partner companies and several small LANs. The traffic between all those needs to be controlled and firewalled. The servers and LANs are divided into different subnets and VLANs. Physically, their traffic is aggregated on a couple of 4506 and then sent to a FreeBSD server, where the logical gateways are set up and traffic is filtered between them.The BSD server is dying and having it there is incorrect in the first place, so we are planning to replace it with two ASA (5520) in failover.The question that arises is how to correctly implement firewalling between VLANs. Originally we thought to set up the firewalls in transparent mode and logically terminate VLANs on a stack of 3750 switches behind them, but would that filter the traffic between the VLANs? Then we thought to perhaps terminate the VLANs on the ASAs, use routing mode, and do filtering there, as well. Or should we implement multiple contexts? We have about 20 VLANs and all of them differ in rules of what should go there. None of this can be concidered an "inside" - trusted - zone, nor "outside". Internet and external links are connected and filtered in a different place.
View 1 Replies
View Related
Aug 3, 2011
I have a customer that has an RSV4000 Router. The customer has also purchased a block of 5 usable public IP addresses. I need to be able to assign these public IP addresses to printers either by configuring a static IP on each printer directly or thru IP mapping or some other method. Does the RSV4000 support using multiple public IP addresses and if so what configuration is needed in the router for the printers to be seen by the outside world.
View 2 Replies
View Related
May 9, 2013
We have ACS 5.3 with built in ACS View, does PI 1.3 support it? We have set up in PI 1.3 but unable to see the authentication records for clients, I wonder if they are compatible.
View 4 Replies
View Related
Nov 18, 2011
i have asa 5505 adaptive security plus. and i have only 3 vlans . outside , inside , DMZ restricted.so it's working fine but i want to connect to my inside another private network, or do i need to buy License.and how i can activate the license key.
View 4 Replies
View Related
Apr 23, 2012
I am thinking about running some third-party unified communications apps under VMWare ESXi5 on a Cisco SRE 900 module. According to the Cisco docs, third-party apps are supported on these modules (see table below) but the app in question is NOT on Cisco's list below.
[URL]
Some questions:
1. As long as the third-party app is capable of running under VMWare/VSphere ESXi5, is there anything on the SRE that would prevent you from running this third-party app even though it's not on Cisco's list?
2. What is Cisco's policy on the use of third-party apps that are not on their list? For example, will they take a support call on the SRE running a non-listed app. (I don't want to void any sort of support contract through the use of a third-party app not on their list).
View 2 Replies
View Related
May 10, 2011
we have a Cisco 2851 router and bought the following IOS::
System image file is "flash:c2800nm-spservicesk9-mz.124-25d.bin"
Cisco IOS Software, 2800 Software (C2800NM-SPSERVICESK9-M), Version 12.4(25d), RELEASE SOFTWARE (fc1)
I thought this version was supposed to have IPv6 support?
TEST(config)#ipv6 unicast-routing ^% Invalid input detected at '^' marker.
TEST(config)#
which IOS should we buy?
View 1 Replies
View Related
Feb 3, 2011
Does WAG160Nv2 support IPv6 addresses primarily for the Gateway's IP and thereafter about all IPs that need to be entered via the web interface?
View 9 Replies
View Related
Apr 10, 2013
I do have a question, is WIC-1SHDSL-V3 able to support ADSL line?
We have WIC-1SHDSL-V3 module used for SDSL line, due to few site need to bring up with ADSL line with 1841 model, but HWIC-1ADSL module already EOS. The replacement model EHWIC-VA-DSL-A is not compatible to 1841. My architect suggest Symmetric Module like WIC-1SHDSL-V3 could be able to tweak the config to support Asymmetric purpose. I did google but do not found such related topic. Can any expert on this area to advice me?
View 1 Replies
View Related
Jul 20, 2011
There is a vlan Finance in my office. The requrement : Vlan Finance is allow to access internet and selected host/network and not allow to access internal network. But from internal network can access to Vlan Finance (Full access). I want to configure using Reflexive ACL, but from Datasheet 4500 doesn't support Reflexive ACL. Intervlan routing is in 4500. Is there any ACL configuration to support my requirement without using Reflexive ACL?
View 1 Replies
View Related
Oct 8, 2012
In setup for old RV042 (V1), when updating / adding Mac addresses, the table is always sorted by IP addresses. But in the new oneRV042 (V3) I have, even with latest firmware 4.2.1.02 the list is random, thereby increasing the chance of user entering DUPLICATE IP addr with diff Mac addr. That will result in conflict.If the firmware sorts the DHCP entries by ip addresses, user would be able to catch duplicate ip errors even if the system does not flag the errors. All Cisco smart engineers can you all get the dhcp entries SORT by ip addresses.
View 2 Replies
View Related
Jun 1, 2012
WE have to deploy ASA5585 in between User vlans & server vlans. we have to find all the ports that needs to be opened on firewall. any tools to do same.
View 2 Replies
View Related
Jul 2, 2002
How to reset DSP on the 2600 and 3600 without reset the controller or reset the routers.
View 2 Replies
View Related
Mar 5, 2012
I got a few Cisco Aironet 3602i. The minimum WLC version to support these is 7.1.91.0. I am planning to upgrade to 7.2.103.0. The minimum WCS version to support these WAP is 7.0.220.0 and the next available 7.0.230.0. Checking the release notes for both of these WCS versions, there is no mention of support for WLC versions listed above.
URL
Am I missing something here ? What versions would be required on WCS and WLC to make all the three entities (WLC, WCS, WAP) inter-operable ?
View 4 Replies
View Related
Apr 25, 2013
we have this:1x wlc 5508 7.2.1031x cisco prime infrasture physical appliance 1.2And for test of clean air 1x ap 3600 seriesBut i have a question if i would like see bluetooth device in neighborhood. On the cisco web i founded 3355 or virtual appliance.
View 1 Replies
View Related
Jul 9, 2012
I have currently a Cisco 3600 router, it has three interfaces (all ethernet interfaces only).We being a client, our requirement is, we want two links one being the primary and one secondary for the fail over.My ISP has done certain configurations, but I am so puzzled what really has been done. I asked with them and they told that they have provided us one public IP 202.166.217.248 via Fibre--> Media Converter-->Ethernet 0/0.At the same time, they have given us a pool of addresses of the network 202.166.216.48/29 through the interface Ethernet 2/1.And we have used all the available public IPs in the server farm.They have told that, for the failover purpose via wireless, they have even used an IP address 202.166.213.114/25.
Now, where my confusion lies is, cant they provide the pool address via fibre? What is the significance of the ip that has been provided via fibre? What actually is its purpose? Isn't it consuming an extra interface ?Cant we have both the primary and secondary link excluding that one additional process?Or, am not understanding the real working mechanism how ISP distribute the internet?
View 1 Replies
View Related
Oct 18, 2012
Can you use a Cisco 3600 to do a P2P bridge? Using the MAP's ethernet port to connect to a remote LAN? On that remote LAN can you have lightweight APs that connect to a controller on the RAP side?
View 13 Replies
View Related
May 7, 2012
This is one I am having a hard time finding an answer for. How many clients can a 3600 AP support? For 150 clients on one of these, what would the throughput be for each client?
If my calculations are correct, the device can deliver 420 Mbps, which gives each client roughly 2.8Mbps. Is this correct?
View 9 Replies
View Related
Mar 26, 2012
we have a customer with a wifi deployment aruba 3600 controller based. Corporate SSID authentication is EAP-TLS double machine and user authentication through ACS 4.2 against AD and Microsoft AC PKI infraestructure based; it was working ok. After migrating from ACS 4.2 to 5.2, both authentication (machine and user) are reported as succeed by ACS but aruba controller does not recognize machine authentication. It seems that controller sees two authentication users and not an machine followed by and user one. We have revised configuration in detail and it seems correct. We begin thinking it could be a bug .
View 2 Replies
View Related
Jun 25, 2012
if the mounting bracket for 3600 AP is the same as the 3500/1140/1040 mounting bracket? I'm suspecting it's not as you can get modules that fit onto the back of the 3600 APs.
View 4 Replies
View Related
Jan 28, 2013
Cant find the software version on my NCS .Apparently once we start using 3600 APs then we need to upgrade.Cisco AP 3600 was introduced in the 7.1.91 or later code stream and is supported by the following: Cisco 2500, 7500, 5508 and WiSM2 Series Controllers, and WCS 7.0.220 or later and NCS 1.1 or later.
Problem is no matter where i look i cant find the current software version for it.
View 1 Replies
View Related
Jan 13, 2013
I am not having much luck getting it converted via normal ways.
It times outs on TFTP server when you hold the mode button (a 3500 is working fine doing the same thing).
I try the old school way of archive download-sw but it isn't fast enough before it re-dhcp's because it can't find a controller. "*Mar 1 01:17:51.123: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP..' Even if I set a static IP address.
Is there way to disable the join process while I upgrade the software? I guess fire up a controller for it to join. I hope I don't have to have a controller to convert these.
View 31 Replies
View Related
Jul 27, 2011
Have been struggling with a connectivity issue following a recent power surge from a storm. A BVI from Cisco Catalyst 3600 cannot communicate with our local network.
We have several satellite connections which connect to us via ADSL. From these satellite offices I can talk to the Cisco 3600 we have here at our central office (BVI 10.60.112.1). There is a connection from the ATM port on the Cisco 3600 which goes to an ATM port on a Cisco Catalyst 8510 and there is an Ethernet connection from that 8510 to the core switch on our local network (Catalyst 6509).
Since I can talk to the 3600 without issue, I believe that the issue is the 8510 config.
There are only two ports in use on the 8510.The ATM port on the 3600 is connected to the 8510's ATM0/0/1.The 8510's ATM1/0/0 (622MM) is connected to our local network's core.There is activity on both ports of the 8510, but from the local network I cannot see 10.60.112.1 and from the 3600 I cannot see the core.
The 8510 config looks pretty default, like some things were "lost" during the surge (we had backups of the 3600 and not the 8510). The config goes as follows for the 8500:
[code]....
View 1 Replies
View Related
Nov 21, 2011
i still newbie to configure eBGP, i have Router 3600 series, and i configure BGP neighbor to my ISP, but the peer still don't established,there is warning like this, Connections established 339; dropped 339 "Last reset 2w4d, due to Peer closed the session No active TCP connection"
any one can explain to me about "due to Peer closed the session"? i've read some documents for troubleshooting BGP, and do some step to troubleshoot.
View 15 Replies
View Related
Jul 22, 2012
I have an AP group on a Cisco 5508 WLAN controller. Currently, it is populated with 13 Cisco 1142 lightweight access points. When I try to add a Cisco 3602i access point to the group, I get the following error in NCS: Error: OfficeExtend requires primary, secondary, or tertiary controller management IP to be set.I am using DNS to allow my AP's to find the controller and they work just fine. Is there a reason I can't add the 3600 series AP's to the AP group?
View 13 Replies
View Related
May 8, 2012
i'm going to upgrade a 5508 wlc code from 7.0.116.0 to 7.1.91.0 to add 3600 series access points having it all manageable via WCS ver 7.0.230.0 it seems to be possible, as it is explained in the compatibility matrix found on [URL]now I have to download the file to the controller...
AIR-CT5500-K9-SPECIAL-7-1-91-0.aes
(direct update possible)
before doing that I'd like to know if I will loose my configuration on the controller i'm concerned about that because the release document is not clear:
- We highly recommend that you back up your controller's configuration files prior to upgrading the controller software. Otherwise, you must manually reconfigure the controller.
- For busy networks, controllers on high utilization, or small controller platforms it is advisable to disable the 802.11a/b/g networks as a precautionary measure.
- Step 5 Disable any WLANs on the controller.
- Step 19 Re-enable the WLANs......
- Step 22 If desired, reload your latest configuration file to the controller. (reload config after reenabling wlans?another controller another question .....: a cisco wlc 2100
found 2 update files
AIR-WLC2100-K9-7-0-230-0-ER.aes
AIR-WLC2100-K9-7-0-230-0.aes
why 2 update files this time? what file to update first?
View 9 Replies
View Related
