Cant find the software version on my NCS .Apparently once we start using 3600 APs then we need to upgrade.Cisco AP 3600 was introduced in the 7.1.91 or later code stream and is supported by the following: Cisco 2500, 7500, 5508 and WiSM2 Series Controllers, and WCS 7.0.220 or later and NCS 1.1 or later.
Problem is no matter where i look i cant find the current software version for it.
I would like to get using of course SNMP, list of client IPs connected to VLAN in Cisco Catalyst 3600.So far, I have pseudo-algorithm made by me which obtains those IP addresses, but I am not sure if this is done in right way :
1) Receive all IP addresses from Catalyst using oid 1.3.6.1.2.1.4.20.1.2. I get something like :
IP-MIB::ipAdEntIfIndex.10.10.2.1 = INTEGER: 152
IP-MIB::ipAdEntIfIndex.10.10.2.251 = INTEGER: 152
IP-MIB::ipAdEntIfIndex.10.10.3.251 = INTEGER: 151 and so on.
2) Get ifIndex of VLAN (oid 1.3.6.1.2.1.4.20.1.2.10.10.2.1.<IP_ADDRESS>) for particular IP address from above list :
IP-MIB::ipAdEntIfIndex.10.10.2.1 = INTEGER: 152
IP-MIB::ipAdEntIfIndex.10.10.2.251 = INTEGER: 152
IP-MIB::ipAdEntIfIndex.10.10.3.251 = INTEGER: 151
3) Get VLAN name (oid 1.3.6.1.4.1.9.9.46.1.3.1.1.4.1.<IF_INDEX>) If_index is borrowed from list above :
IP-MIB::ipAdEntNetMask.152 = No Such Instance currently exists at this OID
IP-MIB::ipAdEntNetMask.151 = No Such Instance currently exists at this OID
In the third step I have this problem, that instance can not be found in OID. It is weird, because for about forty IP addresses i can find about their 10 VLAN names to which they are connected.
How do I know which hardware I have? I can't find a HW version anywhere on the appliance or in WLSE itself. I am guessing 1105 beacuse I saw a 1105 as part of the path in the repository.
View 2 Replies View RelatedI need to find an iOS version that supports BGP, Dot1q, and MPLS for either a 1800 series or 1900 series not sure the best place to find this sort of info out.
View 1 Replies View RelatedI am trying to find out what version my router is, all it has on the model number is "WRT54GS" no version number attached to it.
View 8 Replies View Relatedi went through the website and figured that my firmware is 1.01.05 and there's a new version availble which is 1.01.09 for my Linksys WAG200G modem since im having problem with unstable connection and now, after i updated the firmware, not only that im dropping connection heaps more, my internet connection has slowed down by alot.
View 2 Replies View RelatedIn January 2012 I bought a Linksys E4200v2. I am trying to download a firmware version upgrade and it wants to know what hardware version I have. The top of my router (where the model number is displayed), only has E4200. I have looked through my receipts, the box it came in, and anything else I can find to do with the router - they all have the E4200v2. In case the 'v2' portion is for the hardware version, I do not want to download the wrong firmware version and end up with a router that doesn't work
View 4 Replies View RelatedWhere can i find the lastest version official firmware for my WRT610n V2?
View 9 Replies View RelatedI can't find the correct driver for Belkin F9L1101 Version 1 USB Wireless adapter. When I went here [URL] and installed the software my Windows 7 Pro w/64 bit does not recognize the adapter. When I go to Device Manager it does see the Belkin under other devices. When I choose the folder the drivers are located /program files (x86) it says it can't find the driver in that location.
View 6 Replies View RelatedI cant find the WUSB600n ver.2 drivers on your support page: url...When I click "Version 1.0" it shows me the Win7 driver but by clicking "Version 2.0" it just says: "Guides and Information" but theres no drivers. I suppose it's a bug.I have a new Laptop so I need the Win7 64bit driver for ver.2.
View 2 Replies View RelatedMcAffee scan of acs 1113 appliance running the 4.2 build 124 patch 12 version reports that a medium vulnerability exists because the system has SSH version 1. Any way to specify only version 2 or turn off SSH?
View 9 Replies View RelatedCan we use ACS 4.1 version recovery disc on 4.2 verison to recover the forgotten password.
View 1 Replies View Relatedwhich version of prime infrastructure supports wlc5508 version 7.4
View 2 Replies View Relatedprovide me with the important links which can show me how to do the software upgrade for my ASA 5520 ver 7.0(1) to ver 8.4 ? as well as the ASDM
View 10 Replies View Relatedi am using Cisco ASA 5510 with ASA Version 8.0(4) and memory 256MB. me to Upgrade it to 8.3
View 6 Replies View RelatedWe are looking to upgrade our WiSMs to version 7.0.230.0, but the Cisco compatibility matrix suggests we need to upgrade WCS to the same version (it is currently on 7.0.172.0). My question is can we upgrade the WiSMs and do the WCS at a later date with no issues or do we need to do them at the same time to keep visibility of everything?
The reason I ask is that some of my clients use lobby ambassador for some of their users and they will need wireless access on the day we are due to upgrade WCS (the WiSMs are due to be upgraded and rebooted earlier that morning.
How to reset DSP on the 2600 and 3600 without reset the controller or reset the routers.
View 2 Replies View RelatedI got a few Cisco Aironet 3602i. The minimum WLC version to support these is 7.1.91.0. I am planning to upgrade to 7.2.103.0. The minimum WCS version to support these WAP is 7.0.220.0 and the next available 7.0.230.0. Checking the release notes for both of these WCS versions, there is no mention of support for WLC versions listed above.
URL
Am I missing something here ? What versions would be required on WCS and WLC to make all the three entities (WLC, WCS, WAP) inter-operable ?
we have this:1x wlc 5508 7.2.1031x cisco prime infrasture physical appliance 1.2And for test of clean air 1x ap 3600 seriesBut i have a question if i would like see bluetooth device in neighborhood. On the cisco web i founded 3355 or virtual appliance.
View 1 Replies View RelatedI have currently a Cisco 3600 router, it has three interfaces (all ethernet interfaces only).We being a client, our requirement is, we want two links one being the primary and one secondary for the fail over.My ISP has done certain configurations, but I am so puzzled what really has been done. I asked with them and they told that they have provided us one public IP 202.166.217.248 via Fibre--> Media Converter-->Ethernet 0/0.At the same time, they have given us a pool of addresses of the network 202.166.216.48/29 through the interface Ethernet 2/1.And we have used all the available public IPs in the server farm.They have told that, for the failover purpose via wireless, they have even used an IP address 202.166.213.114/25.
Now, where my confusion lies is, cant they provide the pool address via fibre? What is the significance of the ip that has been provided via fibre? What actually is its purpose? Isn't it consuming an extra interface ?Cant we have both the primary and secondary link excluding that one additional process?Or, am not understanding the real working mechanism how ISP distribute the internet?
Can you use a Cisco 3600 to do a P2P bridge? Using the MAP's ethernet port to connect to a remote LAN? On that remote LAN can you have lightweight APs that connect to a controller on the RAP side?
View 13 Replies View RelatedThis is one I am having a hard time finding an answer for. How many clients can a 3600 AP support? For 150 clients on one of these, what would the throughput be for each client?
If my calculations are correct, the device can deliver 420 Mbps, which gives each client roughly 2.8Mbps. Is this correct?
I have a router 3600 with a power connector kind RPS but I don't have a RPS system, Do it exist a kind of wire that I can connect directly from my router to AC?
View 1 Replies View Relatedwe have a customer with a wifi deployment aruba 3600 controller based. Corporate SSID authentication is EAP-TLS double machine and user authentication through ACS 4.2 against AD and Microsoft AC PKI infraestructure based; it was working ok. After migrating from ACS 4.2 to 5.2, both authentication (machine and user) are reported as succeed by ACS but aruba controller does not recognize machine authentication. It seems that controller sees two authentication users and not an machine followed by and user one. We have revised configuration in detail and it seems correct. We begin thinking it could be a bug .
View 2 Replies View Relatedif the mounting bracket for 3600 AP is the same as the 3500/1140/1040 mounting bracket? I'm suspecting it's not as you can get modules that fit onto the back of the 3600 APs.
View 4 Replies View RelatedI am not having much luck getting it converted via normal ways.
It times outs on TFTP server when you hold the mode button (a 3500 is working fine doing the same thing).
I try the old school way of archive download-sw but it isn't fast enough before it re-dhcp's because it can't find a controller. "*Mar 1 01:17:51.123: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP..' Even if I set a static IP address.
Is there way to disable the join process while I upgrade the software? I guess fire up a controller for it to join. I hope I don't have to have a controller to convert these.
Have been struggling with a connectivity issue following a recent power surge from a storm. A BVI from Cisco Catalyst 3600 cannot communicate with our local network.
We have several satellite connections which connect to us via ADSL. From these satellite offices I can talk to the Cisco 3600 we have here at our central office (BVI 10.60.112.1). There is a connection from the ATM port on the Cisco 3600 which goes to an ATM port on a Cisco Catalyst 8510 and there is an Ethernet connection from that 8510 to the core switch on our local network (Catalyst 6509).
Since I can talk to the 3600 without issue, I believe that the issue is the 8510 config.
There are only two ports in use on the 8510.The ATM port on the 3600 is connected to the 8510's ATM0/0/1.The 8510's ATM1/0/0 (622MM) is connected to our local network's core.There is activity on both ports of the 8510, but from the local network I cannot see 10.60.112.1 and from the 3600 I cannot see the core.
The 8510 config looks pretty default, like some things were "lost" during the surge (we had backups of the 3600 and not the 8510). The config goes as follows for the 8500:
[code]....
i still newbie to configure eBGP, i have Router 3600 series, and i configure BGP neighbor to my ISP, but the peer still don't established,there is warning like this, Connections established 339; dropped 339 "Last reset 2w4d, due to Peer closed the session No active TCP connection"
any one can explain to me about "due to Peer closed the session"? i've read some documents for troubleshooting BGP, and do some step to troubleshoot.
I have an AP group on a Cisco 5508 WLAN controller. Currently, it is populated with 13 Cisco 1142 lightweight access points. When I try to add a Cisco 3602i access point to the group, I get the following error in NCS: Error: OfficeExtend requires primary, secondary, or tertiary controller management IP to be set.I am using DNS to allow my AP's to find the controller and they work just fine. Is there a reason I can't add the 3600 series AP's to the AP group?
View 13 Replies View Relatedi'm going to upgrade a 5508 wlc code from 7.0.116.0 to 7.1.91.0 to add 3600 series access points having it all manageable via WCS ver 7.0.230.0 it seems to be possible, as it is explained in the compatibility matrix found on [URL]now I have to download the file to the controller...
AIR-CT5500-K9-SPECIAL-7-1-91-0.aes
(direct update possible)
before doing that I'd like to know if I will loose my configuration on the controller i'm concerned about that because the release document is not clear:
- We highly recommend that you back up your controller's configuration files prior to upgrading the controller software. Otherwise, you must manually reconfigure the controller.
- For busy networks, controllers on high utilization, or small controller platforms it is advisable to disable the 802.11a/b/g networks as a precautionary measure.
- Step 5 Disable any WLANs on the controller.
- Step 19 Re-enable the WLANs......
- Step 22 If desired, reload your latest configuration file to the controller. (reload config after reenabling wlans?another controller another question .....: a cisco wlc 2100
found 2 update files
AIR-WLC2100-K9-7-0-230-0-ER.aes
AIR-WLC2100-K9-7-0-230-0.aes
why 2 update files this time? what file to update first?
I am using Cisco 7609 IOS15.0(1)S1 and Cisco 3600 IOS 15.1(2)EY.I am trying to provision VPNs over MPLS network.All I found in the documentation is how I attach a whole interface to a VRF.However, I need to be able to attach a VLAN (or any other matching criteria, for that matter) to a VRF.In other words, I want to be able to attach port 1/1 vlan 100 to VRF-A and port 1/1 vlan 200 to VRF-B.
View 1 Replies View RelatedI´m trying to test anntenas in a AIR-CAP3062E-A-K9 the problem is that when I´m below the AP the speed is weak, the AP es with a WLC, so I was wondering if do you know a command or a form to test the anntenas or the Radio.
View 7 Replies View RelatedI have a 5508 controller with a bunch of 3600 Series APs. I did all the basic config on the controller and added all the APs through distribution port #1. Now I was trying to config a second interface ( port #2) and use it for the Guest SSID on a separate VLAN. After I rebooted the controller, it dumped all the APs. I would like to know if this is normal, If I need to enroll the APs everytime I reboot the controller.
View 1 Replies View Related