Cisco WAN :: REP Support On 6509 Series?
Sep 6, 2012Any plans to support REP on the 6500 series?We have Sup 720 with MSFC3.
View 1 Replies
ADVERTISEMENT
Cisco Switching/Routing :: 6509 Series Switches Support VSS Active-Active Chassis
Feb 7, 2012The 6509 Series Switches support the scenario VSS Active-Active Chassis, I would like to setup both switch's as one virtual switch but working at the same time, not with Active - Stand By Chassis.
My plans it to create PortChannel accross both Switches 6509 in order to have 2 links one connected to one slot/switch and the other connected to slot/switch in the second 6509 for servers redundancy.
Cisco Switching/Routing :: Using 6509 Series As Core Switches
Jun 2, 2012we are using cisco 6509 series switches as core switches. and Cisco 4510,4507 series switches as edge switches. all the vlans are created at core switches and propogating to edge switches through VTP. we are using OSPF as routing protocol at core switch for internal routing. till now we are using 4510,4507 switches as layer 2 switches. Since, 4510 & 4507 switches are hign end swithces i want use them as layer 3 switches instead of layer 2.if i change these switches from layer 2 to layer 3 does it make any impact on our network or better to keep them as layer 2 switches.if i change these switches to layer 3 is there any advantage i will have.
View 3 Replies View RelatedCisco Routers :: Does The RV180 Series Support 6rd
May 10, 2012I'm considering upgrading a small business to the newly released RV180 or RV180W.Does the RV180 series support 6rd (IPv6 rapid deployment?).I see 6rd documented in the other small business routers (e.g. RV110), but I can't find it in the RV180 documentation.
View 1 Replies View RelatedCisco :: Why No Support For 3560 Compact Series In CNA
Jan 9, 2012Is there reason why WS-C3560C-8PC-S and WS-C3560C-12PC-S is not supported in Cisco Network Assistent? According to the data sheets for these switches CNA should be supported. I saw another forum post stating that the Gigabit versions has been added to the supported list as of version 5.7."The Cisco Catalyst 3560-C and 2960-C Series compact switches offer both the traditional Cisco CLI for detailed configuration and Cisco Network Assistant software, a PC-based tool for quick configuration based on preset templates."
View 2 Replies View RelatedCisco Switches :: 200 Series SNMP Support
May 28, 2013Am I correct in thinking that 200 series swiches now support SNMP using v1.3?
View 1 Replies View RelatedCisco WAN :: 6509 - Catalysts Does Not Support Module
Jul 31, 2012we have two 6509 catalyst. we bought two new SFM-capable 16 port 1000mb GBIC/WS-X6516A-GBIC module. but our catalysts doesnt support them. we don't know the reason. we tried on another 6500 series catalyst they worked.
here are the outputs from our 6509:
Core-SW-1#sh module
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 0 1-subslot SPA Interface Processor-600 7600-SIP-600 JAE14090958
2 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL1413DX2B
3 16 CEF720 16 port 10GE WS-X6716-10GE SAL1414EL2Q
4 1 Application Control Engine Module ACE20-MOD-K9 SAD1408036Z
5 5 Supervisor Engine 720 10GE (Active) VS-S720-10G SAL1414ERDT
6 5 Supervisor Engine 720 10GE (RPR-Warm) VS-S720-10G SAL1414ERE3
7 16 CEF720 16 port 10GE WS-X6716-10GE SAL1414ER93
8 16 SFM-capable 16 port 1000mb GBIC WS-X6516A-GBIC SAL1326SVBS(code)
Cisco Wireless :: AP Models Which Support 5500 Series?
May 25, 2012are there any AP models which support 5500 series and dont support 4400 series. Actually we are looking to get some new AP with higher bandwidth and External Antenna How to differentiate between AP models with clean air feature supported and not
View 5 Replies View RelatedCisco WAN :: 2921 ISR G2 Series BGP IPv6 Support Required
May 24, 2011I was slightly dissapointed with the performance of the "pre-sales" phone number of Cisco in the Netherlands so I am asking it here instead.We decided on using 2 Cisco 2921 routers with 2.5GB ram to use for a MultiHomed connection using BGP. We already have our v4 and v6 space assigned as well as our AS number. The connections should turn up soon.What I could not find out with proper certainty on the Cisco Feature Navigator is if the IP BASE on the Cisco 2921 supports both IPv4 and IPv6 routing combined with BGP. This model uses the Universal IOS licensing which I found slightly confusing. I could not find a simple matrix with the supported commands either.
View 1 Replies View RelatedCisco Switching/Routing :: IOS For Support Of OSPF And BGP In 6509-E
Sep 13, 2012If i look at the Feature Navigator , it says that IP Base Supports OSPF and EIGRP. But if i look at the Cisco Link it contradicts the Cisco Feature Navigator.
[URL]
if I have 6509-E with VSS-SUP720-10G and want to run OSPF and BGP on the Switch. What is the IOS i require? WIll IP Base Suffice or i need to take Advance or Enterprise Image.
Cisco Switching/Routing :: Support For 6509 Switch
Feb 6, 2013I have number of 6500 switches and we are in the process of getting support contract renewed now when i buy support for my 6500 series switches i have to inform main module serial numbers (Only this one). or do i also have to inform about sub module serial numbers to my support vendor?
View 1 Replies View RelatedCisco Switching/Routing :: 6509-E - IOS Support For Module
Mar 4, 2012I have a switch Cisco WS-C6509-E WS-X6716-10G-3C module ( module for 10 GB) , i have the IOS s72033-ipservicesk9-mz.122-18.SXF9.bin. I want to know if this IOS can support this module or not ? or , if i must do a upgrade , is that the IOS : "s72033-ipservicesk9_wan-mz.122-33.SXH8" work fine ?
View 7 Replies View RelatedCisco Wireless :: 2500 Series Support Mobility Groups?
Dec 1, 2011Do you know if the new 2500 series controller supports things like mobility groups? Could I use 2 of these and do inter-controller roaming. Also do you know if this would work with a 2106 controller and a 2505 controller or are they 2 completely independent controllers only knowing about their own APs??
View 12 Replies View RelatedCisco Wireless :: Does 2500 Series Controllers Support Redundancy
Apr 12, 2012Does 2500 series wireless controllers support redundancy?
View 1 Replies View RelatedCisco WAN :: Does ASR 1000 Series Support DMVPN Hub And Key Server In GetVPN
May 12, 2009Does ASR 1000 Series support DMVPN Hub, and Key Server in GETVPN.
View 2 Replies View RelatedCisco :: When Will Campus Manager 5.2.1 Support 2960S Switch Series
Sep 29, 2011When will Campus Manager support the 2960S switch series?
View 2 Replies View RelatedCisco Routers :: Do SA500 Series Firewalls Support BGP Routing
Feb 5, 2012Do the SA500 Series Firewalls Support BGP Routing?
View 3 Replies View RelatedCisco Switching/Routing :: 3560-C Series L3 Switches Support OSPF?
Jul 16, 2012OSPF normally only comes with IPservices image and not IP Base image. The 3560-C series data sheet says that it only suport IP Base image, yet it mentions that support for OSPF in included. Are there any restictions in the OSPF support?.
View 7 Replies View RelatedCisco WAN :: VS Based 720 Supervisor As Minimum To Support Full BGP On Catalyst 6509-E
Nov 18, 2011I'm currently in the process of evaluating potential equipment options for a Core Router/Switch that will be running BGP with several Tier 1 ISP's, the table download from each ISP will be full (300,000+ Routes). I was looking at a 6509-E with dual SUP720-3BXL supervisors but after reading the below link I'm a little concerned by the maximum routes table: [URL]
Do I have to go to the VS based 720 supervisor as a minimum to support full BGP on a 6509-E? Does any experience of the above switch + supervisor combination under a full BGP table, how well does it work? I'm looking at long term using this as a consolidated core (i.e. a VRF for the Global Internet routing table + a VRF for internal data center traffic, plus maybe some more shared VRF's).
Would I be better keeping a Core switch by itself and just buying edge routers to run BGP?
Cisco Wireless :: 3600 Access Point Series Will Get An Add-on Module To Support 802.11ac
Oct 23, 2012I noticed that the 3600 access point series will get an add-on module to support 802.11ac. This standard will support more than 1 GBit/s.But the 3600 series still do only have got one GBit port. Any extended information about 802.11ac in the upcoming Cisco portfolio?
View 8 Replies View RelatedCisco Switching/Routing :: Does 2600 Series Switch Support 802.1x And DHCP Snooping
Feb 14, 2012does Cisco 2600 series switch support 802.1x and DHCP snooping?
View 6 Replies View RelatedCisco WAN :: Will 2600 Series Router Support 10Mb 10 / 1000 Traffic From New Modem
Jun 26, 2012We are upgrading our incoming Internet service from 30 Mb 10/100 to 100Mb 10/1,000.Will my 2600 series router support the 10Mb 10/1,000 traffic from my new modem?Do I need to change my interface speed from 100 to 1,000? I to be sure my router will support the upgrade. [code]
View 8 Replies View RelatedCisco WAN :: 6500 Series Router Support Supervisor Module Redundancy Like 7304 Does
Jan 24, 20131) Does the 6500 series router support supervisor module redundancy like the 7304 does? IE, can I put two identical sup720 modules in the chassis for failover?
2) Can I use any ethernet interface on any line card on the 6500 series for router interfaces? If not, which line cards work as router interfaces?
3) Differences between the 6500 series and the 7600 series? Can I use a sup720 modules from a 6500 in a 7600?
Cisco Switching/Routing :: Does The 22xx Series FEX Support Static Or Dynamic LAGs Between Itself And A Server
Nov 18, 2012Does the 22xx Series FEX support static or dynamic LAGs between itself and a server?Imagine a server with dual 10G NICs, and I need to connect them to the SAME 22xx FEX....can I set up a LAG between the two 10G NIC ports and two 22xx FEX Host ports? Does it depend on how the FEX is connected to the parent 55xx?
View 0 Replies View RelatedCisco Switching/Routing :: Does Supervisor 720 Support All Existing Catalyst 6500 Series Interface
Feb 12, 2013Q. Does the Supervisor 720 support all existing Cisco Catalyst 6500 series interface and services module, protecting customer investments?
View 1 Replies View RelatedCisco Wireless :: Controller 4400 Series Work With Aironet 3600 Series
Mar 6, 2012Can Controller 4400 series work with Aironet 3600 series?
View 5 Replies View RelatedCisco WAN :: Can't Use Ehwic-3g-hspa-u Card In 2800 Series And 1841 Series Router
Jun 2, 2012why I can't use cisco ehwic-3g-hspa-u card in cisco 2800 series and 1841 series router?documentation said that it should work with that devices but when I installed it, it doesn't work even as device i can't see I am using cisco latest ios advance ent. 15.1(4)M4?
View 3 Replies View RelatedCisco Wireless :: 1140 AP Series Vs 1260 AP Series Technical Differences
Jul 24, 2012What's the main technical differences among the 1140 AP series and the 1260 AP series?I know that the 1260 supports external antennas while the 1140 supports internal antennas, but apart from that, is there any other important difference ?
View 10 Replies View RelatedCisco Routers :: How Does Quality And Longevity Of SRP500 Series Compare To RV Series
May 27, 2012My Draytek 2710 just dies after 2 years so I was looking for something a little more reliable and noticed the spec of the SRP527W-U.I take it with only one antenna and reading a couple of past discussions, the wireless will only manage n-lite as some people call it i.e. 150Mbps, and not the full 300? Oh, and are the ports still only 100M and not Gig?I know the 547 would tick both these boxes but we are talking twice the price. How does the quality and logevity of the SRP500 series compare to the RV series (which would need an adsl modem) or the Linksys boxes?
View 1 Replies View RelatedCisco :: Does WLC 2500 Series Supports 1262 Series Access Point
Jun 14, 2011Does AIR-CT2504-25-K9 spupports AIR-LAP1262N-E-K9 Access Point? How can I check this?
View 1 Replies View RelatedCisco Switching/Routing :: 6509 To 6509-E Chassis Upgrade?
Nov 21, 2011I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3
I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis?Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
Cisco Switching/Routing :: Upgrade Of 6509 To 6509-E Chassis
Nov 21, 2011I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3.I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis. Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
Cisco WAN :: 1700 Series Router To 2811 Series Router / Going From T1 To Ethernet?
Jan 17, 2011I have not done much with business routers, but we have a 1700 series with a WAN WIC-1ENET card with a RJ45 connection. We had a T1 line and will be moving to ehternet. We are going to be moving to a 20MB line, and i just wanted to make sure I have the right connections before installing. We also have a T1 line in another loaton and would be moving to this same 2811 router there as well.We would also like to copy over the configuration from 1700 series router to the 2811 router. Would it be easier to do it by hyper-terminal? Also if we keep the 1700 routers are they capable of using layer-3?
View 2 Replies View Related
