Cisco WAN :: 6509 - Catalysts Does Not Support Module

Jul 31, 2012

we have two 6509 catalyst. we bought two new SFM-capable 16 port 1000mb GBIC/WS-X6516A-GBIC module. but our catalysts doesnt support them. we don't know the reason. we tried on another 6500 series catalyst they worked.
 
here are the outputs from our 6509:
 
Core-SW-1#sh module
Mod Ports Card Type                              Model              Serial No.
--- ----- -------------------------------------- ------------------ -----------
  1    0  1-subslot SPA Interface Processor-600  7600-SIP-600       JAE14090958
  2   48  CEF720 48 port 10/100/1000mb Ethernet  WS-X6748-GE-TX     SAL1413DX2B
  3   16  CEF720 16 port 10GE                    WS-X6716-10GE      SAL1414EL2Q
  4    1  Application Control Engine Module      ACE20-MOD-K9       SAD1408036Z
  5    5  Supervisor Engine 720 10GE (Active)    VS-S720-10G        SAL1414ERDT
  6    5  Supervisor Engine 720 10GE (RPR-Warm)  VS-S720-10G        SAL1414ERE3
  7   16  CEF720 16 port 10GE                    WS-X6716-10GE      SAL1414ER93
  8   16  SFM-capable 16 port 1000mb GBIC        WS-X6516A-GBIC     SAL1326SVBS(code)

View 7 Replies


ADVERTISEMENT

Cisco Switching/Routing :: 6509-E - IOS Support For Module

Mar 4, 2012

I have a switch Cisco WS-C6509-E WS-X6716-10G-3C module ( module for 10 GB) , i have the IOS s72033-ipservicesk9-mz.122-18.SXF9.bin. I want to know if this IOS can support this module or not ? or ,  if i must do a upgrade , is that the  IOS : "s72033-ipservicesk9_wan-mz.122-33.SXH8" work fine  ?

View 7 Replies View Related

Cisco LAN :: 6509-e Best Way To Swap Out Supervisor Module

Mar 28, 2012

We have a 6509-e (WS-C6509-E V04) with (4) (WS-X6148-GE-TX) 48 port modules and a supervisor 32 (WS-SUP32-GE-3B).We purchased a supervisor 720 (WS-SUP720-3B) and (2) (WS-6708-10G-3C) 8 port fiber modules and (1) WS-X6748-GE-TX)48 port module to add to the switch. My question is what is the best way to swap out the supervisor module? Can the SUP720 be added as a standby module so that the config can be transferred? Probably a long shot. Is there anything in this swap that I should be concerned with? The other three modules should be pretty straight forward.

View 4 Replies View Related

Cisco Switching/Routing :: 10Ge Between Catalysts 6500

Nov 18, 2012

I am in front of a choice what to select to deploy 10Ge in my datacenter to get four 6504e and two 3750x units connected to each other.All devices are located in 3-7 meters away from each other.The choice is whether to go for a multimode fiber and 10GBASE-SR X2 Modules OR cat7 UTP and 10GBASE-T X2 pluggable transceiver.Money wise it doesn't matter.Fiber looks less attractive since it's fragile and a bit harder to put in underfloor area.Cat7 is more attractive but there are 2 points:

1) I couldn't find ANY single photo of a 10GBASE-T (a module with a single RJ45 port). How does it look? Does it come with a cable or...??

2) How stable is it to run 10Ge over UTP?

View 1 Replies View Related

Cisco :: 6509 - Can't Access WS-SVC-NAM-2 Module Through HTTP Or Telnet

Jun 16, 2011

I try to access to WS-SVC-NAM-2 module in the Switch 6509. But is not work although the HTTP port is enabled (I tested with the command telnet  @ip 80).
 
I try telnet access to the module to check the config , but I always the message that the lo gin / password is wrong even though they are valid.

View 4 Replies View Related

Cisco WAN :: Remove IPSec VPN SPA Module From 6509 Chassis?

Feb 29, 2012

Need to remove the IPSec VPN SPA module from the 6509 chassis. Does the module is hot swappable or does the 6509 need to be turned off prior to removal.

View 2 Replies View Related

Cisco Switching/Routing :: 6509-E / IOS Requirements For VSS And ACE Module?

Sep 10, 2012

I have a pair of 6509-E Switches running VS-720 Supervisors. We are planning to add Ace Module onto the 6509-E. Will IP Base Image suffice the requirement? Will Ace Module work with only IP Base Image?

View 1 Replies View Related

Cisco Application :: 6509 - ACE Module In Bridge Mode?

May 16, 2011

We have a 6509 with an ACE module. For reasons I don't fully understand the ACE is running using a BVI in bridge mode. It has loads of secondary interfaces.

[Code]...

I can ping all of the IPs on the BVI, but only servers in Subnet 10.7.42/42 can ping out of the the layer 3 on the 6509. I have all the routes configured properly on the 6509 pointing to the ACE for these subnets. The question is though the config has been excepted, is there a limit to the number of secondary on a BVI. 

View 1 Replies View Related

Cisco Switching/Routing :: To Reload The Module 3 On The 6509 Switch

Jul 31, 2012

Suffered a big outage on the network, the fix was to reload the module 3 on the 6509 switch, we had these errors on the log %CONST_DIAG-SW1_SP-3-HM_PORT_TEST_FAIL: Switch 1 Module 3 TestUnusedPortLoopback Port(s)[24,46] failed. System operation continues.in the end, we reloaded the card and it was all ok. is there anything I can do to check the card / or any deeper logs? would that error cause the card to crash?

View 1 Replies View Related

Cisco :: NAM Module On 6509 Doesn't Ping Via Management Port

Apr 27, 2010

I have a cisco 6509 configured with a cisco NAM module. I have reset the config of the NAM module by the config clear command. Since this moment I can't no more ping the NAM module via the management port:  OK via the 127.0.0.91 address and log in ok via the ios cli session command. [code] I have already tried to reboot the module via the ios cli hw module command and nothing better.

View 12 Replies View Related

Cisco Switching/Routing :: 6509 Has Four Module Slots Empty

Apr 1, 2013

I have a cisco 6509 (ws-c6509-e) IOS 12.2.(18)SXF6 with the following modules and submodules: [code] I would like to add another module, I have WS-6816-GBIC or WS-6516-GBIC which one will work with my 6509 ? The 6509 has four module slots empty: 4-7-8-9, Can I add the card in one of these slots ?

View 10 Replies View Related

Cisco Switching/Routing :: 6509 Shuts Down Module While Running VSL

Oct 21, 2012

How I can shutdown a module when I am running vsl.I can use the following command #hw-module module 2 shutdown.As I have modules in both switch 1 and switch 2 how can I ensure I only shut down module 2 in switch 1.

View 1 Replies View Related

Cisco Switching/Routing :: Cat 6509 - VSS - Minor Error (Sup Module)

Mar 17, 2012

We have a VSS environment with two Cisco 6509-Es. IOS image:s72033-ipservicesk9_wan-mz.122-33.SXI5 when I switch on or reload the  Core switches(VSS), I find a Minor Error in the "Show module switch all" command.I also did a "show diagnostic result switch 1 module 5"Switch 1 Module 5: Supervisor Engine 720 10GE (Active)  SerialNo : SAL1521E035

Overall Diagnostic Result for Switch 1 Module 5 : MINOR ERROR
Diagnostic level at card bootup: complete
Test results: (. = Pass, F = Fail, U = Untested)
45) TestVslLocalLoopback:
Port  1  2  3  4  5
-------------------
U  U  U  .  F
 
This issue temporarily relieves when reseating the X2 module, but reappears after reloading the switch.

View 5 Replies View Related

Cisco Application :: 6509 - ACE Module Context On Bridged Mode

May 8, 2013

I am desiging a topology with two Cat 6509 and Two ACE Module, one ACE per Catalyst. I am thinking to  use bridge mode for the customer contexts, I would like to know if the Bridged mode is an Assymetric topology.
 
The server gateway is the ip address of the ACE or the Router?

View 6 Replies View Related

Cisco Switching/Routing :: Expansion Module Required At Existing 6509?

Jan 7, 2013

We have a requirement to build a datacenter within a datacenter for a new project. The existing Core network is 2 x Cisco 6509 in VSS configuration. We would like to connect the new datacenter to the existing Core switch from the new low-end Core switch. This datacenter would have a SAN network and blader chassis.
 
Listing the Cisco Switches requirements and expansion module requirements ?
 
- What expansion module is required at existing 6509 ? Can we have one 10Gibit modules on each switches and crate a port-channel connection from new datacenter core switch ?

- Which model of Switch you recommend for the new Datacenter Core which is only going to have one SAN Enclosure and two blade chassis? Will it be a good option to use 3750E ? If yes do we need any additional modules there ?

- Which aggregation switch should we use for the blade enclosure ?

- Should we have a Cisco Embedded Switch module on the chassis to create trunk with aggregation switch ?

- How the SAN director switch is connecting to the LAN ? should we have any particular module at new Core switch ?

View 0 Replies View Related

Cisco Application Networking :: Catalyst 6509 - ASN Traffic Ace10 Module

Aug 26, 2012

I trying configure ASN traffic load balance, but doesn't works.I have one Cisco Catalyst 6509 and onde Cisco Ace10 module, in my context "PanWEB" i have the interfaces above: [code] If i try to establish a telnet session(telnet 10.96.202.10 80) i see the SYN packet passing through the ACE and going to the real server, but, the server do not response the SYN packet. I done a capture in the server using wireshark and could see that the IP address of the destination is the VIP and not the rserver ip address , this is a problem? Why can not I have the SYN + ACK from the server?

View 5 Replies View Related

Cisco Switching/Routing :: 6509 VSS Implementation As A Service Module Core

Jun 8, 2011

I m planning to implement VSS in core but want some inputs on IOS as i have FWSM as a service module Core :- Ii am running 12.2(33)SXH2a on my Core 6509  and i checkd cisco sites and Fwsm release notes but it states only  I-Train of IOS while mine is H-Train so can I directly upgrade to  I-Train or I was thinking of SXH8b IOS.

View 2 Replies View Related

Cisco Switching/Routing :: 6509 ACE Application Control Engine Module

Oct 4, 2012

We are facing a strange issue, our ACE 20 got failed due to power issue , after RMA once we are installing ACE 20 to 6509 , the status LED is showing ORANGE . The sh module shows it as " Others " ... The IOS is same as it was previously in 6509 .

View 2 Replies View Related

Cisco Firewall :: 6509 - Replacing Faulty FWSM Module In Cluster

Apr 15, 2013

We have a faulty FWSM module in Cisco 6509 switch in Active/Standby cluster mode
 
We have purchased a refurbished FWSM module to replace it. It has the same FWSM OS 4.0 (4) and is in factory default configuration
 
What procedures should I follow to make this unit live and sync the config between the current active unit to this one.

View 1 Replies View Related

Cisco Security :: Does ASA5540-bun-k9 Support CSC-20 Module

Dec 13, 2011

One of my client want to upgrade its already installed ASA5540-bun-k9 by adding CSC-20 Module. As per below link CSC-20 is supported with ASA5540. but for any reason the ASA5540 bundle option with CSC Module  is not available that create confusion.Will CSC-20 Module work with ASA5540-bun-k9 [URL]

View 2 Replies View Related

Cisco Switching/Routing :: 6509 / WS-X6704-10GE Module And Port Status?

Dec 7, 2011

We have two 6509 switches with one WS-X6704-10GE module in each of them. There is an optical cable between the two switches plugged in  WS-X6704-10GE module on both sides. When you shut down the port on one side the other port still stays as up and you need phisycally to unplug the cable to have it down. The same behaviour is seen no matter on which of the two switches you shut down the port, the opposite one always stays as up and only removal of the cable makes it go down.
 
The ports are configured quite simply:
 
interface TenGigabitEthernet1/1
switchport
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1-10
no ip address
udld port
 
The IOS version is 12.2(18)SXF8

View 2 Replies View Related

Cisco WAN :: Does 3745 1FE2W Module Support MPLS

Jan 16, 2011

I have a couple of these routers in the lab with a very basic MPLS configuration on them.  Everything works fine on the fixed interfaces but I cannot get the ldp neighborship to form between the 1FE2W interfaces on each router.  Does this module support MPLS?

View 3 Replies View Related

Cisco VPN :: Sami Module On 7600 IPv6 Support

Apr 3, 2013

Below is my Topo
 
DUT------router(7600)------Sami module (slot 9)

I have both ipv4 and Ipv6 config on all the three hops. Between Cisco and Sami module, I have the Ip config on vlan interface 1400(say). Its not on a physical interface obviously, I can ping ipv5 from DUT to Sami IPv4 address. But Ipv6 doesnt work. If I add a sttic route to DUT network on SAMI, show ipv6 route does not show it.

View 1 Replies View Related

Cisco Switching/Routing :: 6506E With SUP 720 Support 10 GIG Module?

May 4, 2013

switch 6506 E with supp 720 does it support 10 GIG module ?

View 3 Replies View Related

Cisco Switching/Routing :: 6509 Module Results Show Pass And No Errors In The Logging

Sep 18, 2012

We have a design of two 6509 running in a VSS with dual supervisor each having fthree 10/100/1000mb etherner modules. We have diagnosed a wierd problem that none of the switchports in module 1 and 2 on either switches are having layer2/layer 3 connectivity.
 
Tried everything from changing the cables to changing the end device but no luck with it.
 
Module results show pass and no errors in the logging.

View 2 Replies View Related

Cisco Firewall :: ASA 5585X URL Filtering / Unable To Support CSC Module?

Aug 22, 2011

Because ASA5585X doesn't support CSC module, how can do URL filtering on ASA5585X

View 1 Replies View Related

Cisco Application :: Does ACE Service Module Support SHA2(256) Certificates

Sep 1, 2010

Does ACE service module support SHA2(256) certificates? I see that private key generation defaults to SHA1 and does not provide any option, also the cipher suites in SSL parameters map do not show SHA2 options. Can it handle SHA2 in any software release? I am currently running A2(2.3) build 3.00

View 6 Replies View Related

Cisco :: 1130AG Access Point Module Will Support Radius

Nov 4, 2012

In our Environment we used to Connect to wifi using   Radius Authentication Through AD Account  (Encryption: TKIP and  CIpher, Authentication Open+EAP and Network EAP,  Key management WPA) this settings  which will be done And pushed through AD Itself.We Use CIsco 1130AG, 1200 Series in most of the areas which have no Issues.But We Have Some trouble with Cisco WAP4410N Access point.In This Access point users were not able to Connect to wifi through Radius Authentication.However users were able to Connect  to these Access point, but  it is unsecured, whoever configure's the correct client settings in their PC. They can connect to SSID. This Access point is capable of supporting Radius Authentication?

View 4 Replies View Related

Cisco Switching/Routing :: SFP-GE-T Module Support On Nexus 5548?

Jan 7, 2013

I am trying to install SFP-GE-T module on Nexus 5548UP Switch, but is giving the ‘SFP validation Failed’ error. The details of the switch is given below

Model : N5K-C5548UP-FA

The interface is configured with speed 1000 before inserting the module, still we are getting the same error. PFA logs for more details We have 8 Nos of SFP-GE-T modules , all are giving same error. We tried to insert the module on onboard as well as expansion module.

The same module is working fine on Cisco 3750X-24T-L Switch As per the Hardware installation guide , SFP-GE-T transciever is supported on N5K platform. Please extend your support in configuring SFP-GE-T module on N5K platform? We tried with SFP-GE-S module on the same switch , and the same is found working fine.

View 2 Replies View Related

Cisco WAN :: REP Support On 6509 Series?

Sep 6, 2012

Any plans to support REP on the 6500 series?We have Sup 720 with MSFC3.

View 1 Replies View Related

Cisco WAN :: 2911 - Support Interface ADSL Module Like Backup Link?

Apr 27, 2011

i will going to buy a router 2911 but i want know if support a interface ADSL modulo like backup in case that my primary link WAN Ethernet down and up the adsl link with a module HWIC ADSL pots.

View 1 Replies View Related

Cisco Wireless :: 3600 Access Point Series Will Get An Add-on Module To Support 802.11ac

Oct 23, 2012

I noticed that the 3600 access point series will get an add-on module to support 802.11ac. This standard will support more than 1 GBit/s.But the 3600 series still do only have got one GBit port. Any extended information about 802.11ac in the upcoming Cisco portfolio?

View 8 Replies View Related

Cisco WAN :: 6500 Series Router Support Supervisor Module Redundancy Like 7304 Does

Jan 24, 2013

1) Does the 6500 series router support supervisor module redundancy like the 7304 does? IE, can I put two identical sup720 modules in the chassis for failover?

2) Can I use any ethernet interface on any line card on the 6500 series for router interfaces? If not, which line cards work as router interfaces?

3) Differences between the 6500 series and the 7600 series? Can I use a sup720 modules from a 6500 in a 7600?

View 4 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved