I have a switch Cisco WS-C6509-E WS-X6716-10G-3C module ( module for 10 GB) , i have the IOS s72033-ipservicesk9-mz.122-18.SXF9.bin. I want to know if this IOS can support this module or not ? or , if i must do a upgrade , is that the IOS : "s72033-ipservicesk9_wan-mz.122-33.SXH8" work fine ?
View 7 Replies
we have two 6509 catalyst. we bought two new SFM-capable 16 port 1000mb GBIC/WS-X6516A-GBIC module. but our catalysts doesnt support them. we don't know the reason. we tried on another 6500 series catalyst they worked.
here are the outputs from our 6509:
Core-SW-1#sh module
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 0 1-subslot SPA Interface Processor-600 7600-SIP-600 JAE14090958
2 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL1413DX2B
3 16 CEF720 16 port 10GE WS-X6716-10GE SAL1414EL2Q
4 1 Application Control Engine Module ACE20-MOD-K9 SAD1408036Z
5 5 Supervisor Engine 720 10GE (Active) VS-S720-10G SAL1414ERDT
6 5 Supervisor Engine 720 10GE (RPR-Warm) VS-S720-10G SAL1414ERE3
7 16 CEF720 16 port 10GE WS-X6716-10GE SAL1414ER93
8 16 SFM-capable 16 port 1000mb GBIC WS-X6516A-GBIC SAL1326SVBS(code)
I have a pair of 6509-E Switches running VS-720 Supervisors. We are planning to add Ace Module onto the 6509-E. Will IP Base Image suffice the requirement? Will Ace Module work with only IP Base Image?
View 1 Replies View RelatedSuffered a big outage on the network, the fix was to reload the module 3 on the 6509 switch, we had these errors on the log %CONST_DIAG-SW1_SP-3-HM_PORT_TEST_FAIL: Switch 1 Module 3 TestUnusedPortLoopback Port(s)[24,46] failed. System operation continues.in the end, we reloaded the card and it was all ok. is there anything I can do to check the card / or any deeper logs? would that error cause the card to crash?
View 1 Replies View RelatedI have a cisco 6509 (ws-c6509-e) IOS 12.2.(18)SXF6 with the following modules and submodules: [code] I would like to add another module, I have WS-6816-GBIC or WS-6516-GBIC which one will work with my 6509 ? The 6509 has four module slots empty: 4-7-8-9, Can I add the card in one of these slots ?
View 10 Replies View RelatedHow I can shutdown a module when I am running vsl.I can use the following command #hw-module module 2 shutdown.As I have modules in both switch 1 and switch 2 how can I ensure I only shut down module 2 in switch 1.
View 1 Replies View RelatedWe have a VSS environment with two Cisco 6509-Es. IOS image:s72033-ipservicesk9_wan-mz.122-33.SXI5 when I switch on or reload the Core switches(VSS), I find a Minor Error in the "Show module switch all" command.I also did a "show diagnostic result switch 1 module 5"Switch 1 Module 5: Supervisor Engine 720 10GE (Active) SerialNo : SAL1521E035
Overall Diagnostic Result for Switch 1 Module 5 : MINOR ERROR
Diagnostic level at card bootup: complete
Test results: (. = Pass, F = Fail, U = Untested)
45) TestVslLocalLoopback:
Port 1 2 3 4 5
-------------------
U U U . F
This issue temporarily relieves when reseating the X2 module, but reappears after reloading the switch.
We have a requirement to build a datacenter within a datacenter for a new project. The existing Core network is 2 x Cisco 6509 in VSS configuration. We would like to connect the new datacenter to the existing Core switch from the new low-end Core switch. This datacenter would have a SAN network and blader chassis.
Listing the Cisco Switches requirements and expansion module requirements ?
- What expansion module is required at existing 6509 ? Can we have one 10Gibit modules on each switches and crate a port-channel connection from new datacenter core switch ?
- Which model of Switch you recommend for the new Datacenter Core which is only going to have one SAN Enclosure and two blade chassis? Will it be a good option to use 3750E ? If yes do we need any additional modules there ?
- Which aggregation switch should we use for the blade enclosure ?
- Should we have a Cisco Embedded Switch module on the chassis to create trunk with aggregation switch ?
- How the SAN director switch is connecting to the LAN ? should we have any particular module at new Core switch ?
I m planning to implement VSS in core but want some inputs on IOS as i have FWSM as a service module Core :- Ii am running 12.2(33)SXH2a on my Core 6509 and i checkd cisco sites and Fwsm release notes but it states only I-Train of IOS while mine is H-Train so can I directly upgrade to I-Train or I was thinking of SXH8b IOS.
View 2 Replies View RelatedWe are facing a strange issue, our ACE 20 got failed due to power issue , after RMA once we are installing ACE 20 to 6509 , the status LED is showing ORANGE . The sh module shows it as " Others " ... The IOS is same as it was previously in 6509 .
View 2 Replies View Relatedswitch 6506 E with supp 720 does it support 10 GIG module ?
View 3 Replies View RelatedWe have two 6509 switches with one WS-X6704-10GE module in each of them. There is an optical cable between the two switches plugged in WS-X6704-10GE module on both sides. When you shut down the port on one side the other port still stays as up and you need phisycally to unplug the cable to have it down. The same behaviour is seen no matter on which of the two switches you shut down the port, the opposite one always stays as up and only removal of the cable makes it go down.
The ports are configured quite simply:
interface TenGigabitEthernet1/1
switchport
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1-10
no ip address
udld port
The IOS version is 12.2(18)SXF8
I am trying to install SFP-GE-T module on Nexus 5548UP Switch, but is giving the ‘SFP validation Failed’ error. The details of the switch is given below
Model : N5K-C5548UP-FA
The interface is configured with speed 1000 before inserting the module, still we are getting the same error. PFA logs for more details We have 8 Nos of SFP-GE-T modules , all are giving same error. We tried to insert the module on onboard as well as expansion module.
The same module is working fine on Cisco 3750X-24T-L Switch As per the Hardware installation guide , SFP-GE-T transciever is supported on N5K platform. Please extend your support in configuring SFP-GE-T module on N5K platform? We tried with SFP-GE-S module on the same switch , and the same is found working fine.
We have a design of two 6509 running in a VSS with dual supervisor each having fthree 10/100/1000mb etherner modules. We have diagnosed a wierd problem that none of the switchports in module 1 and 2 on either switches are having layer2/layer 3 connectivity.
Tried everything from changing the cables to changing the end device but no luck with it.
Module results show pass and no errors in the logging.
If i look at the Feature Navigator , it says that IP Base Supports OSPF and EIGRP. But if i look at the Cisco Link it contradicts the Cisco Feature Navigator.
[URL]
if I have 6509-E with VSS-SUP720-10G and want to run OSPF and BGP on the Switch. What is the IOS i require? WIll IP Base Suffice or i need to take Advance or Enterprise Image.
I have number of 6500 switches and we are in the process of getting support contract renewed now when i buy support for my 6500 series switches i have to inform main module serial numbers (Only this one). or do i also have to inform about sub module serial numbers to my support vendor?
View 1 Replies View RelatedCan 10Gbase SFP+ module support 1GB traffic on a Nexus 5596T.
The module for 10Gb is Cisco SFP-10G-SR. My scenario is connecting the 10GB SFP+ module to an access switch 1GB fiber uplink, will this work?
I've been researching the 3750-x Netflow support but I'm not 100% sure of how much support it has. From what I've read the only way to get NetFlow support is to install a specific module that provides NetFlow. I also heard about how it might support s-flow but I haven't found out for sure.
View 8 Replies View RelatedWe got a requirement for 2 number of X2-10GB-SR line card WS-X45-SUP6-E in WS-C4506-E.Customer want to connect with Fujitsu primary server . they have 10 gig module so i guess it will support with that.Also a doubt this X2-10GB-SR we can directly connect the firber sc multimode cable write no additional sfp required write .And for my knowledge if i use CVR-X2-SFP. I think to multimode sfp we have to insert write so do we get to 10 gig ports in one slot or how is it .
View 1 Replies View RelatedThe 6509 Series Switches support the scenario VSS Active-Active Chassis, I would like to setup both switch's as one virtual switch but working at the same time, not with Active - Stand By Chassis.
My plans it to create PortChannel accross both Switches 6509 in order to have 2 links one connected to one slot/switch and the other connected to slot/switch in the second 6509 for servers redundancy.
I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3
I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis?Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3.I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis. Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
We have a 6509-e (WS-C6509-E V04) with (4) (WS-X6148-GE-TX) 48 port modules and a supervisor 32 (WS-SUP32-GE-3B).We purchased a supervisor 720 (WS-SUP720-3B) and (2) (WS-6708-10G-3C) 8 port fiber modules and (1) WS-X6748-GE-TX)48 port module to add to the switch. My question is what is the best way to swap out the supervisor module? Can the SUP720 be added as a standby module so that the config can be transferred? Probably a long shot. Is there anything in this swap that I should be concerned with? The other three modules should be pretty straight forward.
View 4 Replies View RelatedI try to access to WS-SVC-NAM-2 module in the Switch 6509. But is not work although the HTTP port is enabled (I tested with the command telnet @ip 80).
I try telnet access to the module to check the config , but I always the message that the lo gin / password is wrong even though they are valid.
Need to remove the IPSec VPN SPA module from the 6509 chassis. Does the module is hot swappable or does the 6509 need to be turned off prior to removal.
View 2 Replies View RelatedWe have a 6509 with an ACE module. For reasons I don't fully understand the ACE is running using a BVI in bridge mode. It has loads of secondary interfaces.
[Code]...
I can ping all of the IPs on the BVI, but only servers in Subnet 10.7.42/42 can ping out of the the layer 3 on the 6509. I have all the routes configured properly on the 6509 pointing to the ACE for these subnets. The question is though the config has been excepted, is there a limit to the number of secondary on a BVI.
I have a cisco 6509 configured with a cisco NAM module. I have reset the config of the NAM module by the config clear command. Since this moment I can't no more ping the NAM module via the management port: OK via the 127.0.0.91 address and log in ok via the ios cli session command. [code] I have already tried to reboot the module via the ios cli hw module command and nothing better.
View 12 Replies View RelatedI am desiging a topology with two Cat 6509 and Two ACE Module, one ACE per Catalyst. I am thinking to use bridge mode for the customer contexts, I would like to know if the Bridged mode is an Assymetric topology.
The server gateway is the ip address of the ACE or the Router?
I trying configure ASN traffic load balance, but doesn't works.I have one Cisco Catalyst 6509 and onde Cisco Ace10 module, in my context "PanWEB" i have the interfaces above: [code] If i try to establish a telnet session(telnet 10.96.202.10 80) i see the SYN packet passing through the ACE and going to the real server, but, the server do not response the SYN packet. I done a capture in the server using wireshark and could see that the IP address of the destination is the VIP and not the rserver ip address , this is a problem? Why can not I have the SYN + ACK from the server?
View 5 Replies View RelatedWe have a faulty FWSM module in Cisco 6509 switch in Active/Standby cluster mode
We have purchased a refurbished FWSM module to replace it. It has the same FWSM OS 4.0 (4) and is in factory default configuration
What procedures should I follow to make this unit live and sync the config between the current active unit to this one.
One of my client want to upgrade its already installed ASA5540-bun-k9 by adding CSC-20 Module. As per below link CSC-20 is supported with ASA5540. but for any reason the ASA5540 bundle option with CSC Module is not available that create confusion.Will CSC-20 Module work with ASA5540-bun-k9 [URL]
View 2 Replies View RelatedI have a couple of these routers in the lab with a very basic MPLS configuration on them. Everything works fine on the fixed interfaces but I cannot get the ldp neighborship to form between the 1FE2W interfaces on each router. Does this module support MPLS?
View 3 Replies View RelatedBelow is my Topo
DUT------router(7600)------Sami module (slot 9)
I have both ipv4 and Ipv6 config on all the three hops. Between Cisco and Sami module, I have the Ip config on vlan interface 1400(say). Its not on a physical interface obviously, I can ping ipv5 from DUT to Sami IPv4 address. But Ipv6 doesnt work. If I add a sttic route to DUT network on SAMI, show ipv6 route does not show it.
