Below is my Topo
DUT------router(7600)------Sami module (slot 9)
I have both ipv4 and Ipv6 config on all the three hops. Between Cisco and Sami module, I have the Ip config on vlan interface 1400(say). Its not on a physical interface obviously, I can ping ipv5 from DUT to Sami IPv4 address. But Ipv6 doesnt work. If I add a sttic route to DUT network on SAMI, show ipv6 route does not show it.
I have Cisco router 7606-S. On Sami module led is indicate red. i also test it to other slot,reload the chassis but the problem is same. The module status is unnkown.
(Indicates red one of the following conditions:
• The SAMI is released from reset by the supervisor engine and is booting.
• The boot code failed to run.)
pdsn1#sh mod
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 7 SAMI Module WS-SVC-SAMI-BB-K9 SAL15056HSV
2 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL14480S9Q
5 2 Route Switch Processor 720 (Active) RSP720-3C-GE SAL1538QE8N
6 2 Route Switch Processor 720 (Hot) RSP720-3C-GE SAL1538QHZB
[code]....
1.is this a hardware problem of sami module?
2. is this a boot problem of sami module? is this image problem of modules(supervisor or sami module)?
how i do diagnostics this module?
if the 7600-SIP-200 supported in VSS mode or not ?
I have configured to Cisco Catalyst 6513 as VSS, both of them have the 7600-SIP-200 module, before converting them to VSS I was able to work with the 7600-SIP-200 module, but after I did convert them to VSS, both modules didn't work.
here is the show module output, after VSS conversion:
VSS1#show module Mod Ports Card Type Model Serial No.--- ----- -------------------------------------- ------------------ ----------- 1 0 4-subslot SPA Interface Processor-200 7600-SIP-200 JAE14500GMT 7 5 Supervisor Engine 720 10GE
[Code].....
What are the limitations of Net flow v9 support on the 7600 platform for the SR code releases?
I know that Flexible Net flow is only available on newer releases with some newer hardware. Flexible Net flow gives you the ability to provide full support for Netflow v9 as well as IPFIX.
However, the documentation indicates that Net flow v9 is still supported in the SR code. So I am just trying to find out what are the limitations in how Net flow v9 is implemented without "Flexible Net flow". The Cisco TAC was unable to provide me any documentation about this.
I´m looking for an IOS on a 7609 SUP720/MSF3 that supports the NAT-PT feature (IPv4 to IPv6 translation). I searched on the Cisco Feature Navigator but the tool didn´t show up any IOS for the 760x platforms. I only got the feature "NAT-PT: Support for Overload (PAT)" with IOS 15.xS train.
View 2 Replies View Relatedhow many sessions a BGP Route Reflector can support? is it 10, 100 or 1000 BGP sessions? What degradation of performance may arise in the case of a BGP RR sessions overload? Consider that the RR I'm deal with has both the control plane and teh forwarding plane. Which command I may use for get the output about BGP sessions resurces used level?
The following are the data about the RR:
Cisco 7600
WS-SUP720-3BXL
Version 12.2(33)SRD5
cisco CISCO7609 (R7000) processor (revision 1.2) with 983008K/65536K
i just came to know Assurance feature license doesn't come for free when upgrading from LMS4.2 or NCS1.1. It has to be purchased. Before buying this license, i would like to know if IPv6 netflow is supported.
View 0 Replies View RelatedI need to implement IPv6 for ASA VPN. According to the ASA_8.4_cli_cfg.pdf , IPv6 is not supported on ASA IPSEC vpn and remote client vpn. I do not have a ASA 8.4, any way to verify on ASA8.4 whether the crypto command support ipv6 address ? If the crypto command do support ipv6 address then probably there is chance it will work.what i mean is eg. crypto map xxx set peer <ipv6 address| ipv4 addres> able to set ipv6 address.
View 4 Replies View RelatedDoes cisco LMS v3.2 Support IPV6 in all modules ? We will be migrating from V4 to V6 in some time from now
View 1 Replies View RelatedAccording to the url below, i could find that there is a separate module required for asr 9k, is it so; doesnt it sufficient to have the 4.3.0 Ios-xr version for the cgnat supoort features of nat 44, nat64, ds-lite.. like things?URL
View 1 Replies View RelatedI would like to get it clarified, that Cisco WLC 2504 running the code ( 7.2.110.0 ) does support IPv6 or not ?
From Cisco Documents they are asking to enable IPv6 support under WLAN > Edit Page, and Enabling mulicast on Ethernet Multicast Mode under Controller > General.
But from the GUI am not able to find the above two field, Even in Interface i created under Controller > interface is not accepting IPv6 address. I am able to configure IPv6 ACL .
Is any deployment document is available to show different scenarios with configuration.
Note - Am using Access point AIR-LAP1262N-N-k9
Is there any IPv6 support planned or in the works for RV082?
View 3 Replies View RelatedI want to ask that does ASA 5580 support the nat-pt for IPv6?
View 2 Replies View Relatedwe have a Cisco 2851 router and bought the following IOS::
System image file is "flash:c2800nm-spservicesk9-mz.124-25d.bin"
Cisco IOS Software, 2800 Software (C2800NM-SPSERVICESK9-M), Version 12.4(25d), RELEASE SOFTWARE (fc1)
I thought this version was supposed to have IPv6 support?
TEST(config)#ipv6 unicast-routing ^% Invalid input detected at '^' marker.
TEST(config)#
which IOS should we buy?
how to add IPv6 support via HE's TunnelBroker to an RV016.
View 0 Replies View RelatedI've got older SOHO97 which I want to use as a backup for Cisco 800 but I can not find any information if it actually supports IPv6. Neither the data sheet [URL] nor the Cisco Feature Navigator [URL] suggest it has any IPv6 support at all.
View 1 Replies View RelatedI was slightly dissapointed with the performance of the "pre-sales" phone number of Cisco in the Netherlands so I am asking it here instead.We decided on using 2 Cisco 2921 routers with 2.5GB ram to use for a MultiHomed connection using BGP. We already have our v4 and v6 space assigned as well as our AS number. The connections should turn up soon.What I could not find out with proper certainty on the Cisco Feature Navigator is if the IP BASE on the Cisco 2921 supports both IPv4 and IPv6 routing combined with BGP. This model uses the Universal IOS licensing which I found slightly confusing. I could not find a simple matrix with the supported commands either.
View 1 Replies View Relatedi want ti migrade lan from ipv4 to ipv6.. how can i check my switch support ipv6?
i am having cisco 3500 and d-link managed and unmanaged switchs.
Does WAG120N Support IPv6 ?
View 1 Replies View RelatedWould like to see IPv6 support on the WAG320N. Some ISPs now support this protocol....should eventually become a standard feature.
View 1 Replies View RelatedI purchased a Latitude E6220 with a 4G WWAN modem (the DW5800). My intention was to support DirectAccess, i.e. Microsoft's clientless VPN, but unfortunately I have not found any way to get the IPv6 protocol installed on the device.
I've searched Verizon Wireless, Dell and Novatel Wireless forums without any success.
was told to allow Ipv6. Does my modem support this?
View 1 Replies View RelatedDoes Nexus 7000 support ipv6 6to4 tunnel?
View 3 Replies View RelatedI have cisco 2960 and Catlyst 4510 switches now we are planning to implement IPV6.
i have the fallowing IOS on my switches.
C2960-lanbasek9-mz.122-50.se5
Cat4500e-entservicesk9-mz.122-54.sg1.bin
The above ios will support for IPV6 or I have to purchase new IOS, which version will support.
I know that the E3000 does not have IPv6 support. I wanted to know if it will get a firmware update to support it?
View 9 Replies View RelatedI find much document, but not found information about whether those support for IPv6 e.g. dual-stack like newer series.
View 3 Replies View RelatedI Have a requirement to migrate from ipv4 to ipv6, I have checked the scalability of all the devices for this migration except ACS 1113 Solution Engine, Version 4.2. I couldnt reach the proper documentation to check its support for ipv6.
View 1 Replies View RelatedI am having WS-C3560G-48TS switch with ios(c3560-ipbasek9-mz.122-58.E2.bin) and I am trying to use IPv6 feature in this switch model. More over I've upgraded this switch with many ios but none of them not supporting IPv6 feature. ios which supports IPv6 feature?
View 3 Replies View RelatedI have the cisco 3640 with IOS Version 12.2(46) , and it with DRAM:32M , Flash:8M.What IOS version can support IPv6 RIP in the hardware limit?
View 3 Replies View RelatedIPV4 IP addresses will be running out in less than a year and I wanted to know, will there be a firmware update for WRT120N to support IPV6?
Also, if I have to buy another router to support IPV6, I'm going to buy a D-Link. It's nothing personal, I just find it absolutely idiotic that a router that supports wireless-N doesn't support IPV6. You have to ask your self, how does the standard IPV6 spec thats a few years old not make it to the final product of a router, but a non-standard wireless-N spec implementation somehow got the O.K....?
Region : Ireland
Model : TL-MR3420
Hardware Version : V2
Firmware Version :
ISP :
I have my router updated with the latest firmware and I'm pretty sure all the settings are correct but I'm only getting a max transfer rate of 144Mbps. I know this because I use InSSIDer 3 to analyse my wifi network etc. I stream movies over my network and while DVD quality movies play fine, HD movies tend to freeze and buffer a lot. I have the router's channel width set to 40Mhz, so I know that's not the problem. Strangely, I also use a Netgear wifi extender with the MR3420 and it's max rate is 300Mbps.
Does WAG160Nv2 support IPv6 addresses primarily for the Gateway's IP and thereafter about all IPs that need to be entered via the web interface?
View 9 Replies View RelatedOne of my client want to upgrade its already installed ASA5540-bun-k9 by adding CSC-20 Module. As per below link CSC-20 is supported with ASA5540. but for any reason the ASA5540 bundle option with CSC Module is not available that create confusion.Will CSC-20 Module work with ASA5540-bun-k9 [URL]
View 2 Replies View Related