Since the 5500X series firewalls use a software IPS SSM that is set up differently from the old ones, I am a little confused on the initial setup.
[URL]
we see a proposed setup for L3 management of the IPS
interface GigabitEthernet0/0
nameif outside security-level 0
ip address 203.0.113.1 255.255.0.0
[Code].....
We are working with a contractor to upgrade our network, and I heard from them that the 5596/5548 might not need the Layer 3 module for our inter-VLAN routhing. They have yet to give me an answer.
We do have a few static routes on our current layer-3, core switch too.
Our requirement with that appliance is to do URL blocking and filtering.Are there any other options we can consider or is it SaaS only. Would have preferred Trend Micro, but don't this is possible with this appliance.Will content security be offered on the Cisco ASA 5500-X Series?At this time, content security services are not supported on the Cisco ASA 5500-X Series appliances. However, the ASA 5500-X Series Cisco Cloud Web Security ready. Cisco Cloud Web Security provides content security as a cloud-based software as a service (SaaS).
View 1 Replies View RelatedI bought a 5500 series ASA and SecPlus license for example. Suddenly my ASA hardware got broken and changed for a new one. What about my old license? How i could activate this license on new ASA?
View 2 Replies View RelatedI tried looking in ASA documentations but unable to find out that how many IPSec Tunnels can be terminated to an ASA cluster. I have 5545 running only two IPSec Tunnels so far but need to terminate 18 sites all up and would like to confirm how many tunnels we could terminate? Is there a limitaion to it?
View 2 Replies View RelatedDoes Cisco ASA 5510 and 5505 has module for increase performance VPN ?
View 3 Replies View RelatedWe have the ASA firewalls in our environment - two 5510's and one 5520.Our 5510's are currently used in our production environment and the 5520 is our firewall for pre-production and support personnel. My question is about the AnyConnect VPN licenses we have. Currently we have 100 seats for AnyConnect on our production ASA's, but we'd like to see if we can move half of these to the 5520 ASA?
View 1 Replies View Relatedare there any AP models which support 5500 series and dont support 4400 series. Actually we are looking to get some new AP with higher bandwidth and External Antenna How to differentiate between AP models with clean air feature supported and not
View 5 Replies View Related: %DATACORRUPTION-1-DATAINCONSISTENCY: unterminated string in buffer of length 129, counted: 129 -Traceback= 4027CB2C 402B1E88 4052884C 40528A48 40528D08 40529188 40529358 403247E8 403247D4
Cisco Internetwork Operating System Software
IOS (tm) C5RSM Software (C5RSM-ISV-M), Version 12.2(46), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2007 by cisco Systems, Inc.
Compiled Thu 26-Apr-07 19:41 by pwade
Image text-base: 0x40010948, data-base: 0x410F41D0
[code]....
The access point is reply when I ping it from WLC. But until know it can't join, even discovery packet isn't arrive in WLC.
WLC software version = 6.0.199.4
Management interface address = 192.168.120.10 /24
Model = 5508
Access point software = 1240 Software (C1240-RCVK9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1) AP Model = cisco AIR-LAP1242G-E-K9 Interface address = 192.168.121.151
I have this version Ap "c1200-rcvk9w8-tar.124-21a.JA2" and a WLC 5500. When i connect the ap to the network i can ping from ap to wlc and the wlc to ap, but the proccess of lwapp messages give errors on the Ap when the Ap try to download the image from wlc and could not join the wlc. why this could be? this is the info of the wireless lan controller.
View 6 Replies View RelatedI understand that Cisco have at long last provided a facility to separate HTTP web authentication from HTTPS WLC management on WLC code 7.2.x for the new 5500 series WLCs.
My question is does Cisco intend to provide the same much needed functionality on the 4400 series WLCs that are running 7.0.x code? I was looking through the release notes for v7.0.235.3 code and that did not seem to mention this functionality. I know we can get around the problem by purchasing an SSL certificate so that guest users with web authentication do not have to see the same security warning each time they log in but the idea to separate the HTTP web authentication from HTTPS WLC management seems so much simpler.
The Release Notes for 7.0.116.0 of WLC 5500 has a table which title is "Client Type", and it shows wireless adapters. My question is,
what kind of customer means? Wireless clients or clients for an specific application? If it was the first option, does it mean tha just this adapters could connect to my wireless network?
I understand that the NM-1FE Fastethernet modules are not compatible with Cisco 2600 series routers, just the Ethernet 1-E module. With that being said, are there ANY modules supported by the 2600, 2621 or 2621XM series routers that have fastethernet port(s) outside of the pricey NM-16ESW module? I don't need a 16 port module!
View 3 Replies View RelatedI am trying to add WCCP to be configured for websense. My first option seems to be either purchase an IPServices license for the stack of 3750E switches, but i am thinking this will require us to license all three switches in the stack. The second option i am looking at is to do the WCCP configuration on the 2800 router we have on the edge. The problem is both Gig ports are in use, one going to the firewall and the second going to the ISP. My first question would be, which option is better in terms of manging as well as cost of implementing it.The second question is, if WCCP on the router is a better option, what is the add on module i should be looking to get to add the additional ports to hook up the Websense cache.
View 8 Replies View RelatedI noticed that the 3600 access point series will get an add-on module to support 802.11ac. This standard will support more than 1 GBit/s.But the 3600 series still do only have got one GBit port. Any extended information about 802.11ac in the upcoming Cisco portfolio?
View 8 Replies View RelatedI have a 7K running 6.1 code, on F series line cards. I need to set it to prioritise DSCP EF marked traffic, that's all at this stage, but am unclear on the configuration steps required. The packets will already be marked, I just need to ensure they end up in a priority queue.
View 2 Replies View Related1) Does the 6500 series router support supervisor module redundancy like the 7304 does? IE, can I put two identical sup720 modules in the chassis for failover?
2) Can I use any ethernet interface on any line card on the 6500 series for router interfaces? If not, which line cards work as router interfaces?
3) Differences between the 6500 series and the 7600 series? Can I use a sup720 modules from a 6500 in a 7600?
We have been deploying ASA 5500 series devices for longer than I've been around. We have always used a script from a tftp server that would use the "wr net" command to send the running-config to the tftp server for daily backups. The script was setup to automatically name these "hostname-mm/dd/yyyy" for each device. We cannot seem to get this working on devices running ASA 8.43. In fact I can't even get the "wr net" command to work from the ASA at all even though I have the tftp server defined correctly (note this is going over the "outside" interface so I always get the warning regarding using the interface with the lowest security level). I'm sure there is something out there that I have overlooked, however I have not been able to come across this. Have there been any changes in the setup, or functionality of the wr net command or the tftp configuration with ASA 8.43?
View 1 Replies View Relatedis it possible to setup a Cisco ISR 881W so it connects to a Cisco ASA 5500 series head via network extension mode? We did this in the past with our PIX connecting to 3000 series concentrator.
View 1 Replies View RelatedHow to you setup ip routing on a Nexus 5500 I want to do vlan routing between an Nexus 5500 and Catalyst 3750. Nothing clever just have the 2 switches talk and vlans route between the two.
View 3 Replies View RelatedCan any ASA 5500 in particular the ASA5510 firewall support jumbo frames (i.e. greater than the default standard 1500 Bytes frames)?. I plan to use the ASAs to setup a point-to-point IPSec tunnel and need an Application frame of 4Kbytes intact and not segment it.I have done little checking on the Cisco Website and see it mention of Jumbo frames on the 5580 on 10Gig interface but didn't see mention 5510. 5580s are way over-kill and expensive for what I need is to run a mission critical one IPSec point-to-point with maximum of no more than 100Kbps so 5510 is perfect for me but not sure if it can carry the jumbo frame?
On the routers and switches it's the MTU settings and they are configurable per interface and I am OK and the circuit is T1 which the Telcos said it's OK since it's physical layer so the only unkown is the firewall.
We are looking to purchase some addidtional 48 port swithches for our network. Currently we have the following swtiches setup
2 of 3750 POE-24 (These two are stacked and have our servers plugged into them). Currently no SFP modules.
3 of 3560 POE-24 (These each have two 1000BASE-T SFP modules in them, with UTP connecting back to the 3750 switches above)
We are looking to get 2 of 48 port C2960S-48TS-L switches with two 1000BASE-T SFP modules in each that then will also connect back to the 3750 switches.
I had a few of question about this:
Will the cisco lite version (rather than the more expensive cisco base software) support the 1000BASE-T SFP modules?
The 1000BASE-T SFP modules, are they auto-config? Have you the link for commands we can use, if required?
We don't have budget for stack modules, apart from that would you recommend we change anything with the new setup?
I have a router 819 with 3G built-in. Are there any manual for how to setup the interface celluar 0 for this router out there? I have Verizon as my 3G provider.
View 4 Replies View RelatedI purchased the license P/N: ASA-CSC20-250U-1Y with Description: ASA 5500 CSC-SSM-20 250-User License Only Renewal (1-year)
But I had a mistake because I need support to 500 users. Now, to solve my mistake I want to know Do I can purchase another ASA-CSC20-250U-1Y to provide the 500 users suppor?
I mean, ¿are two (2) ASA-CSC20-250U-1Y equivalent to the 500 user license listed below?P/N, ASA-CSC20-500U-1Y with Description: ASA 5500 CSC-SSM-20 500-User License Only Renewal (1-year)
Trying to set-up a p2p link between a L2 fast ethenet module (within a 2900) to a 6506.Have created a subinterface SVI on the 2900 and put the fast ethernet port in the respective VLAN. However on 6506, am I correct in thinking I can do a no switchport and just create a L3 interface? Do I need to put the 6506 in the same vlan and the fast ethernet module and create a L3 SVI on it? As it's not a trunk port between the 6506 and the fastethernet module, the packets won't be tagged?
View 3 Replies View Relatedhow to setup the 5508 Series LAN wireless controller. The online documentation are not details. What different between Service Interface IP and Management interface IP. The device IP is using what type service or management interface.
View 2 Replies View RelatedI would like to setup RDP on my cisco router so I can access my server from outside my network. I also have a router from my ISP that has DHCP for my external IP address and DHCP for my internal as well.
View 3 Replies View RelatedI'm new to the Cisco Aironet Access Point. I got a new STANDALONE Aironet 1260 series access point device. The part # AIR-AP1262N-A-K9. The shipping package did not come with any guide, CD, and power adapter. I searched the Cisco sites, but could not find appropriate manuals. I did find a getting started guide but not for standalone AP, it's for Controller-based AP. Question - where can I find manuals / guides to set up and configure my new standalone Cisco Aironet Access Point 1260?
View 3 Replies View RelatedI just setup my homelab today, after having Cat5e installed so I can run my servers and network equiptment over wired network as well as setting up a wireless system. I got everything setup and its going great I can access everything from my office now including a E4200 Linksys router that I setup to do RiP (was only choice pretty much, or NAT), and my 891 Cisco Router which is my internet connection.
I use to have the linksys setup to do port forwarding but now I need to figure out how to do it on the cisco 891 router via command line.
Below is my current configuration. I need to be able to access my server which is behind my router by Remote Desktop. I also have a web server, and the kids also play minecraft, and have a server setup so I need to be able to forward their port as well.
[URL]
Ths is from the link above, would I just do like that but then put in my IPs and is that my Private IP I use this or my public facing. Also he has "interface Dialer1 6881" again after the port in the second and third row. I dont really understand what they have there. I understand basic access list and such though I am extremely rusty.
!
ip nat inside source list 102 interface Dialer1 overload
ip nat inside source static tcp 10.0.0.2 6881 interface Dialer1 6881
[Code].....
I am planning to implement wireless network in my work place. Plan is to have two networks one for guests and one for employee. I am trying to find a guide for 2500 WLC but couldn't find one.I've been reading couple of articles about setting up radius server and CA. I want to know what the best way to approach this.In my environment I got a CA server windows server 2003 and current DC's are windows server 2008 R2.I got 2500 WLC with POE switch and 4 aironet AS 1142.
View 16 Replies View RelatedI am planning to implement wireless network in my work place. Plan is to have two networks one for guests and one for employee. I am trying to find a guide for 2500 WLC but couldn't find one.
I've been reading couple of articles about setting up radius server and CA. I want to know what the best way to approach this.
In my environment I got a CA server windows server 2003 and current DC's are windows server 2008 R2.
I got 2500 WLC with POE switch and 4 aironet AS 1142.
I got the task of setting up a Guest wireless network for one of our remote campuses. We already have some APs that are connecting to our WLC.
The Enviroment:WLC Cisco 5500 is at our Corporate office. Connects to our Core Switch then to our Router Router connects to our remote campuses over mpls.
We currently already have APs at this campus that are connecting back to our WLC.
We have a DSL line at the remote campus that we want this Guest wireless routed to.
I have already created the guest network on the WLC and a guest VLAN on the Core switch.
My main question is how to configure the two routers for this and have this go out the DSL modem?