Cisco Infrastructure :: ASA 5500 - Changes To Wr Net Setup In ASA 8.43
Jun 3, 2012
We have been deploying ASA 5500 series devices for longer than I've been around. We have always used a script from a tftp server that would use the "wr net" command to send the running-config to the tftp server for daily backups. The script was setup to automatically name these "hostname-mm/dd/yyyy" for each device. We cannot seem to get this working on devices running ASA 8.43. In fact I can't even get the "wr net" command to work from the ASA at all even though I have the tftp server defined correctly (note this is going over the "outside" interface so I always get the warning regarding using the interface with the lowest security level). I'm sure there is something out there that I have overlooked, however I have not been able to come across this. Have there been any changes in the setup, or functionality of the wr net command or the tftp configuration with ASA 8.43?
View 1 Replies
ADVERTISEMENT
Oct 9, 2012
I am thinking of upgrading the WCS to Cisco Prime NCS in our environment, but i read NCS is replaced by Prime infrastructure. Now I am confused if I should go for the NCS or Infrastructure. option for a smaller environment with 200APs and 4-5 WLCs(5500, 4400 and 2100) and future proof for the next 5 years. I heard WCS is going to be obsolete soon but didnt find any official announcement except for legacy licenses?
View 5 Replies
View Related
Mar 11, 2003
I need to do one Catalyst 5500 as a TFTP server.Can I do it?Is the catalyst available to be a tftp server?
View 4 Replies
View Related
Feb 14, 2012
how to export objects (net and security) from an ASA 5500 firewall to a .csv file?
View 1 Replies
View Related
Feb 23, 2011
is it possible to setup a Cisco ISR 881W so it connects to a Cisco ASA 5500 series head via network extension mode? We did this in the past with our PIX connecting to 3000 series concentrator.
View 1 Replies
View Related
May 16, 2013
Since the 5500X series firewalls use a software IPS SSM that is set up differently from the old ones, I am a little confused on the initial setup.
[URL]
we see a proposed setup for L3 management of the IPS
interface GigabitEthernet0/0
nameif outside security-level 0
ip address 203.0.113.1 255.255.0.0
[Code].....
View 1 Replies
View Related
Apr 19, 2013
How to you setup ip routing on a Nexus 5500 I want to do vlan routing between an Nexus 5500 and Catalyst 3750. Nothing clever just have the 2 switches talk and vlans route between the two.
View 3 Replies
View Related
Jan 5, 2012
Steps to repeat the bug:
1) Physical Reset of SR520-FE to factory defaults
2) Run CCA 3.1(1) and connect to 192.168.75.1 using the default cisco/cisco login
3) Under the Home Menu, click the Device Setup Wizard
4) In Step 1, sellect the SR520 and observe that there is also a photograph of the SR520-FE(W) model displayed as feedback for Step 1
5) Try variations of Steps 2 through 4
Note: Step 4 has a problem because it says to plug the power into the device, but if the power was not already plugged in to begin with, we could not run the Device Setup Wizard in the first place.
6) Step 5 prompts for a user name and password.
BUG: No permutations of the documented default usernames and passwords "cisco" or "admin" work. The result is always the error dialog:Device Connectivity Status - "Failure: Not Connected.""Return to Step 1. Make sure that your PC is not connected to a network and you follow all the instructions."A search of the web indicates others are also had this unresolved issue with previous CCA releases.
View 1 Replies
View Related
Jun 17, 2012
I would like to set up a POTS Dial connection between 2 Cisco routers, using the modem card WIC-1AM-V2. I'd like to use this as an out-of-band connection to a remote site, if the primary internet connection fails. So, this setup will only be used in one direction, 1 router placing calls, the other one receiving calls.Here's my config of the receiving router:
chat-script dial "" ATZ AT OK "ATX3D T" ATS0=8 TIMEOUT 120 CONNECT C
interface Async0/2/0 description out of band for network no ip address encapsulation slip async mode interactive
line 0/2/0 session-timeout 5 absolute-timeout 10 script connection dial login local modem InOut transport input all escape-character BREAK autoselect ppp stopbits 1 speed 115200 flowcontrol hardware
[code]....
This config is working fine, when dialing in via a Windows Hyperterminal Dial connection. After a while of dialing I get the login prompt of the router.Now I want to have a router placing calls instead of a Windows Server. I can't figure out how to tell a router to place calls to a POTS phone number.
Receiving router: 2811, WIC-1AM-V2, IOS c2800nm-ipbasek9-mz.124-25a
Calling router: 1841, WIC-1AM-V2, IOS c1841-advsecurityk9-mz.124-25a
View 5 Replies
View Related
Apr 19, 2012
I got the task of setting up a Guest wireless network for one of our remote campuses. We already have some APs that are connecting to our WLC.
The Enviroment:WLC Cisco 5500 is at our Corporate office. Connects to our Core Switch then to our Router Router connects to our remote campuses over mpls.
We currently already have APs at this campus that are connecting back to our WLC.
We have a DSL line at the remote campus that we want this Guest wireless routed to.
I have already created the guest network on the WLC and a guest VLAN on the Core switch.
My main question is how to configure the two routers for this and have this go out the DSL modem?
View 9 Replies
View Related
Jan 23, 2012
How to successfully manage to configure ACS 5.1 to accept log in request from a 5500 WLC?
I've managed to get it configured following the follow link [URL], but when I try to log in to the WLC using my ACS credentials I just get the log in screen again. I've checked the ACS logs and it says my username has passed the authentication process and it matches all the rules I've set. The only thing I've noticed is my "Privilege Level" is only 1 but I'm not sure if thats correct for a HTTP log in.
View 21 Replies
View Related
Jun 5, 2011
We have a WLC 5500 apliance, but i have a problem, the APs have a administrative IP in a diferent segment, only conected to WLC the AP have same segment of the management interface, the 5500 don´t have APmanager interface.How configurate the WLC to conected and administrate all AP with different segment IP
Product Version.................................. 6.0.182.0
chasis: AIR-CT5508-K9
View 3 Replies
View Related
Jun 27, 2011
Due to lack of address space, I have to go to NAT for our wireless guest users.Are there any limitation with WLC/NGS when comes to NAT?I have four 5500 WLCs, should I put them in 1 mobility group, at 2 different locations?
View 1 Replies
View Related
May 3, 2011
We have a customer requirement of providing secure connectivity from Remote Office to HQSame time to provide certain level of layer 3 redundancy via secondary link should the primary link fail We are looking at ASA5500 series firewall for both Remote office and HQ.Can this be done?
View 3 Replies
View Related
Nov 8, 2011
Is there a way to set up Quick VPN on the RV120W without changing the internal subnet? I have just taken over responsibility for a network and I don't know all of the nooks and crannies yet, so I'd rather not change the internal sub net. I've tried setting up a user then changing the LAN settings afterward, but it automatically removed the VPN user when I did so.
View 1 Replies
View Related
Jan 1, 2012
I've just purchased a couple of SRP527W routers. I've been unable to even browse to the default 192.168.15.1 to start my configuration. My local network is 192.168.1.x. At risk of showing my stupidity, what am I doing wrong.
View 5 Replies
View Related
May 30, 2012
We have a single 4404 that was setup long before I arrived with Guest networks that timeout and other such tweaks. Is there a document somewhere that shows a way to migrate the old settings to a new 5508 that we are purchasing? By the time the 5508 arrives I will have a very small window to setup the unit before a new wing goes live. I need the new unit as we have reached our limit of licensed AP's on the old 4404. It seems like everyone keeps talking about an easy way but no one says how to do it.
I have never setup one of these units before from scratch so I don't know how long it will take.
View 6 Replies
View Related
Feb 10, 2011
I have been trying to conect a Cisco VPN client through an ASA and it makes the connection but doesn't allow any traffic through. The ASA does have a site to site VPN attached to the outside interface.I suppose the first question is it possible to allow VPN client to connect through an ASA 5500 from the inside network when there are Site to Site VPN's already attached to the outside interfaces?If possible then what have I missed. I have tried adding NAT exempt for the traffic between the internal networks and "an IPSEC pass thru Inspect Map".
View 4 Replies
View Related
Mar 18, 2013
I have a 3750X set up with a number of VLANs and have connected a WLC5500 to this. I've assigned the port on the switch to the correct VLAN, given the WLC a management address on that VLAN and it has the correct gateway. I can ping to this gateway from other devices, but not from the WLC and can't ping or browse to the management address of the WLC (I can browse to it when plugged directly into the SP).
When checking the switch arp table, it shows the IP entry of the WLC as INCOMPLETE yet show cdp nei detail shows the device on the correct IP and all the device details. I have changed the port on the switch, the port on the WLC, the cable and the GBIC, cleared the arp and rebooted all devices and it hasn't made any difference. On the switch, I tried assigning the burned-in MAC to that IP statically but it didn't work - does each port have an individual MAC?
View 3 Replies
View Related
Nov 15, 2011
We have the ASA firewalls in our environment - two 5510's and one 5520.Our 5510's are currently used in our production environment and the 5520 is our firewall for pre-production and support personnel. My question is about the AnyConnect VPN licenses we have. Currently we have 100 seats for AnyConnect on our production ASA's, but we'd like to see if we can move half of these to the 5520 ASA?
View 1 Replies
View Related
Feb 8, 2011
i have a query regarding the no. of isakmp policy priority creating..when i create a new policy in ASA 5500 firewall, i get the below error...i assume it will support only 20 nos, where as we can use between 1-65535.. can anyone from cisco confirm it...running version is 8.x & VPN Plus license.Policy limit reached. No more than 20 isakmp policies can be configured.”
View 2 Replies
View Related
Aug 13, 2012
i have to open ports for vedio conferencing in my Firewall configuration ,
View 1 Replies
View Related
May 11, 2011
we are looking forward to monitoring the cpu, environment variables and the memory of a wireless lan controller via snmp. but we are not able to find in the mibs the right oid to manage this.can the exact oid be given in order to monitor these three elements on a cisco WLC 5500 series.
View 1 Replies
View Related
Dec 15, 2011
I have an ASA 5500 series and am looking to set up the AnyConnect VPN. Looking at this guide everything seems fairly straightforward. However, on the inside private network DHCP is setup and I was wondering if it was possible to just use DHCP instead of providing a static address pool? I did not see any option to do this.
View 1 Replies
View Related
Aug 2, 2012
I want to use ASA B as a forwarder between ASA A and ASA C so that intranet A is connected securely from intranet C, something likes: intranet A <-- ASA A --> internet <-- ASA B --> internet <-- ASA C --> intranet C because connections between A and B and between B and C are good, but connections between A and C are bad. I just completed the IPSec settings between A and B and between B and C, but how should I tell ASA A, B, and C to work like this?
View 5 Replies
View Related
Aug 1, 2011
l need change a wlc 4400 to 5500, but l don´t know what l need back up, and how can I do to join the H Reap APs in the new 5500 WLC because all H Reap APs that l have, are not in the same city , and I understand if l want join AP in the new WLC l need to connect in the same network segment, is it rigth ?
View 7 Replies
View Related
Aug 21, 2011
My problem includes little bit design issue.I have site2site vpn between customer and my cisco router.But the customer wants to add L2TP traffic in this site2site tunnel.I have no experince about L2TP tunneling.I have also ASA 5500 series which locates behind the Cisco router.ASA interfaces have not public IP.Question is that Can I use my ASA firewall for just L2TP tunelling?Every document says ASA use IPSEC over L2TP. But IPsec tunneling is already done by Cisco Router. Or should I have to do both tunnel in same network device? I mean ASA or Router?
View 1 Replies
View Related
Aug 16, 2011
How much the CPU is impacted by SSL VPNs on Cisco ASA 5500's?I believe that the ASA offloads a lot of its encryption/decryption on a built in VPN accelerator rather than placing load on the main CPU. Is this correct?
According to the ASA 5520 specs - it can handle a throughput of up to 225Mbps of VPN traffic. Of course, it does not say whether this is SSL or IPSEC but I would like to understand what impact say 100Mbps of SSL VPN traffic would have on the main CPU.
We need this information to gauge whether an existing firewall has enough capacity to cope with existing load plus additional new SSL VPNs.
View 1 Replies
View Related
Feb 28, 2013
My client has two ASA-5500 in failover (8.4.4.1).To create AnyConnectVPN, the package must be uploaded on both machines - uncomfortable, but it can be accepted. The REAL problem is that the profiles (.xml file) are not synchronized.When I make a change of any of the parameters, after failover switching I loos alle the change.
View 1 Replies
View Related
Aug 18, 2011
Our client ( a webhost, they have a lot of servers ) has a an older Cisco Pix, everything works fine with the PIX. They have a Cisco ASA 5500 with ASA version 8.3 , to replace the PIX. Upon migrating the PIX config to the ASA we are running into issues with Dynamic NAT. The static NAT entries are working flawlessly (there is a lot of them), however when Dynamic is enabled for the remainging hosts, outside communication works then drops off. The remaining hosts need outside access for updates. We have access lists set up but I dont se ehow that could cause a problem when the original ACL's were working fine with the PIX, they have not been altered.
The NAT config may be wrong or cluttered, have a look at the full NAT config.
The static NAT addressing is the same, example 207.11.129.65 will equal 10.10.10.65
View 1 Replies
View Related
Mar 12, 2013
I want to upgrade the WLC 5500 from 7.0.220.0 to 7.3.112.0, coul be any risk if i do the upgrade..?
View 2 Replies
View Related
Jan 16, 2013
I have a Cisco 5500 Software Version 6.0.199.4. Today I've been able to succesfully add a few newly purchased 1242G APs to my WC so I know everything is setup properly. They got the proper DHCP info and I was up and running in a few minutes.
I'm now trying the same thing with a newly purchased Air-Lap1262N-a-KP
I can read the bootup because I'm attached to it on the console.I see that it gets the proper IP#
But then I keep getting a "failed to decode the discovery response" error.
[code]....
View 9 Replies
View Related
Jun 14, 2011
I have two ASA 5510 with Security Plus license and Shared SSL VPN licensing enabled.
The problem is that the client get “Session could not be established: session limit of 25 reached” but ther is only 6 ssl vpn user connected with AnyConnect.The software on the firewall’s is 8.2(1)Is there any BUG in this software related to this problem?
View 1 Replies
View Related