Cisco VPN :: Does ASA 5500 Has Module Increase Performance
Jul 21, 2012Does Cisco ASA 5510 and 5505 has module for increase performance VPN ?
View 3 Replies
ADVERTISEMENT
How To Increase Internet Performance / Signal
Jul 5, 2011I currently have a dlink dir-655 in my basement. my computer on the second floor is connected via DWA-160. I Only have around 2-3 signal bars, and never get the 300mbs like described. i would like to know all the possibilities to extend my range (to have 5 bars) or get better connection speed. do you recommend an access point or an extender? Which models? also, if i have an dir-615, can i use it as an acesspoint/range extender for my computer on the 2nd floor? if so, how? I am looking for the cheapest alternative in order to have better signal and speed. The modem is stuck in the basement therefore I cannot move it.
View 3 Replies View RelatedCisco Switching/Routing :: SUP720 / Performance Increase From 30mbps To 400mbps
Jan 21, 2012Supervisor Engine 720 options support centralized forwarding rates up to 30Mbps and distributed forwarding rates up to 400Mpps. I never understood the claim of forwarding rate logic in mbps. How i can load the 6509 box to check this forwarding rate?How can the performance increase from 30mbps to 400mbps? is this just because of DFC on all the line cards if yes does it mean i have to add the DFC on SUP as well .
View 3 Replies View RelatedCisco Application :: ACE20 Module Upgrade Performance
Jun 28, 2011I have a ACE20 module with a performance of 4 Gbps. I want to upgrade the performance from 4 Gbps to 8 Gbps. Is correct the following SKU for the upgrade?
ACE30-UPG-08-K9=ACE10 or ACE20 to ACE30 Upgrade for 8 Gbps Throughput
And if i want to upgrade the performance to 16Gbps is correct the sku?
ACE30-UPG-16-K9=ACE10 or ACE20 to ACE30 Upgrade for 16 Gbps Throughput
I noticed that the price list of both codes is the same....
Is it right for the SKUs listed I get the new module with the performance ACE30 requested?
Cisco Firewall :: IPS Module Setup On 5500-X Series ASA
May 16, 2013Since the 5500X series firewalls use a software IPS SSM that is set up differently from the old ones, I am a little confused on the initial setup.
[URL]
we see a proposed setup for L3 management of the IPS
interface GigabitEthernet0/0
nameif outside security-level 0
ip address 203.0.113.1 255.255.0.0
[Code].....
Cisco Switching/Routing :: Layer 3 Module Required For 5500 Series Switch?
May 16, 2013We are working with a contractor to upgrade our network, and I heard from them that the 5596/5548 might not need the Layer 3 module for our inter-VLAN routhing. They have yet to give me an answer.
We do have a few static routes on our current layer-3, core switch too.
Cisco :: Way To Increase PoE Budget
Dec 16, 2011If you have a PoE capable switch, is there any way to increase the PoE budget? Especially the 3750 range. I've heard people say that by adding another power supply in the switch you can increase the budget.I've got a 48-port 3750 and I may need to connect a lot of Class III (15.4W) PoE devices. Power budget of a 3750 is 370 Watts, enough for 24 Class III, but likely I'll need more.
View 2 Replies View RelatedCisco :: Increase The TTL Of An OSPF Hello Packet?
Jul 12, 2012Isn't there a way to increase the TTL of an OSPF Hello packet or am I thinking of a different protocol? Or is it only with virtual links? I can't seem to find it in my ROUTE cert book or on the Intarwebz outside of setting TTL security, but I could have sworn I remembered configuring something like this in my ROUTE lab book that I unfortunately do not have at work.
View 8 Replies View RelatedAny Way To Increase Amount Of Bandwidth
Feb 6, 2013Recently I bought a new router and it works great but I'm still having bandwidth issues. On average there are 6 devices running at once, but only two of which do anything that takes up a significant amount of bandwidth and the router is a good distance away from my computer and my brothers (we do online computer gaming). Is there any way to increase the amount of bandwidth we get up here with out having to move the modem and router?
View 1 Replies View RelatedHow To Increase Network Speed
Jun 25, 2011how to increase speed in my network (10 pc)
View 1 Replies View RelatedHow To Increase Bandwidth For Windows 7
Jul 28, 2011Today I purchased a Gatway laptop from Best Buy. Here is all the information NV51B15U, 4GB DDR3 Memory, AMD Dual-Core Processor E-350, 250 GB HDO. My internet is Virgin Mobile EVDO Mobile Broadband. I have know knowledge of computers or this USB internet I have. When I try to go onto Youtube to watch videos the video will play for about 2 sec stop and starts to buff the play then stop and so on. I have java and flash player 10 installed. I was told that I may need to go through another internet provider as the speed from the USB cord will never get any faster. Is this true? Is there something I can do to be able to watch videos without having to wait 10-15 minutes for it to load?
View 6 Replies View RelatedHow To Increase Internet Availability
Dec 10, 2011what fields of IT increase internet availability. I have lived in South Korea for the last six months. I can't say how much better life is because there seems to be universal high-speed internet access, even at 24/7 fast food places like Dunkin' Donuts, McDonalds, etc.).
View 3 Replies View RelatedCisco WAN :: JN7700 - Tunnel Causes Increase In Latency
Feb 19, 2011I have one hub router connected to an ISP cloud and then a spoke router connected to the same ISP cloud. There is a dmvpn connection from the spoke to the hub router and i have attempted to do a few tests from the spoke to the hub router.
When i do a ping from the wan interface (tunnel source) of the spoke router to the wan interface (tunnel source) of the hub router i get a return time of about 700ms on the average. However when i ping from the LAN of the spoke to the LAN side of the HUB, my return time increases to 1000ms and sometimes as high as 3000ms. I suspect the hughes modem HN7700 on the wan side of my spoke to be the cause of the problem.
Cisco VPN :: Increase Of SSL VPN User Licenses On ASA5510?
Nov 9, 2011is that possible to increase the number of SSL VPN User Licenses on ASA5510-SSL100-K9 using for example L-ASA-SSL-50= ?Is there any limitation ?
View 3 Replies View RelatedCisco WAN :: How To Increase HWIC Density In 3845
Dec 27, 2011I have got 3845/3945, I would like to increase HWIC slot density for HWIC 4 PORT ISDN BRI S/T ports through the NM/NME/NMX slots, Is there any measns to do that?
View 2 Replies View RelatedBroadband :: How To Increase Replication Speed
Mar 17, 2013My company has 2 sites. Between them we have 100 MGB link. We do replication every day our data. Recently we had a issue on replication then we stopped about 20 replication. And now issue is fixed, we are started replication. Average replication is 75%, we need to reach it 100% ASAP. But me and my co-worker have little bit different mind about replications are running in same time. I thought there is no difference for total time between one by one and all running in same. But co-worker saying one by one is much quicker.
View 2 Replies View RelatedNew Setup Due To The Increase In Devices Of Internet
Jul 9, 2011I have a new setup in my home due to the increase in devices needing internet access.I bought a 8 port netgear switch and have it connected to my router.My question is this, will the speed/performance of my internet be lower(via switch) compared to if I was just connected straight to the router,
View 2 Replies View RelatedHow To Increase Internet Speed On Computer
Jan 11, 2011I am having trouble with my internet speed at my computer my provder says the speed is fine from their end 100mbps but when i check the speed at my end i am only getting 32mbps the other clue is when I am on a web page it constantky flickers. I have reset the router by turning off the power and then back on the other thing i have done is change the ethernet cable.
View 1 Replies View RelatedBroadband :: How To Increase Download Speed
Oct 4, 2011I AM USING "1" M.B.P.S.LOCAL AREA NETWORK. I AM GET ONLY "100" KBPS DOWNLOAD SPEED HOW TO INCREASE MY DOWNLOAD SPEED?
View 1 Replies View RelatedHow To Increase Youtube Upload Speed
Aug 26, 2012I uploaded an .avi media file, which filled 2.81GB and it took me 7 hours!I was like holy ***, how is it even possible for it to take so long time for an file that only fills 2.81GB?
View 4 Replies View RelatedHow To Increase Wifi Signal Strength
Jun 3, 2012I have computers scattered across our home, and in many areas it is not feasible to run ethernet cable. At one location (less than 30 feet away) but through multiple walls, I can barely connect to any POS (I have two). I added a stand alone antenna extension with long antennas on both the router and the WiFi card on the PC, however, this made zero improvement.What should I be looking to purchase to increase the signal strength? I've already tried different routers.
View 5 Replies View RelatedUpgrade Antenna To Increase Range?
Jul 18, 2011I have one AP with dual antennas and I want to upgrade one of the antenna to 7Dbi to increase the range. will it work
View 1 Replies View RelatedHow To Increase Laptop Wireless Range
Jul 1, 2011How to increase my Laptop wireless range?
View 2 Replies View RelatedCisco :: Cannot Increase MTU To Support Extra Four Bytes Of VLAN Tag
Oct 22, 2012We have an EHWIC for a 2900 router. Apparently, this card supports QinQ.. However, there is no usual MTU command. Therefore we cannot increase the MTU to support the extra four-bytes of VLAN tag. We have tried 15.2 and 15.1 code. May be the command is different. I'm about to go and do some digging elsewhere.The card is EHWIC-4ESG.
View 6 Replies View RelatedCisco Wireless :: WAP4410N To Increase The Number Of Users
Apr 15, 2013I am considering deploying several of these for our church to provide internet access. When reading the manual, I found on the last few pages that the device only supports a max of 63 users at a time. Is that correct? If so, any way to add more ?
View 1 Replies View RelatedCisco VPN :: Increase Timeout Value On IPSECtunnel Running On ASA5520?
Sep 28, 2011How can I increase the timeout value on an IPSEC VPN tunnel running on an ASA5520? The users claim the tunnel is timing out causing transactions to stop flowing.
View 2 Replies View RelatedCisco Switching/Routing :: How To Increase PoE Power On 2960-s
Oct 16, 2012I got a Cisco 2960-S LAN (support PoE+) switch installed in one of my customers' office. The customer needs to plug some cameras to the switch and need inline power from the swtich.
Two of the cameras requires 24W power in order to work correctly, if just use normal PoE power, can't get all functions working and get an error message on the screen says "not enough power" or something like that. I have configured those two port to static power inline (on a max value which is 30W). Once the configuration applied, shut/ no shut the port, the error message disappeares for a few minutes, and then comes back. Looks like the power level is still on PoE not PoE+.
Is there anything I can do on the configuration to increase the inline power and provide a stable power to that kind of devices?
SW02#sh power inline
Module Available Used Remaining (Watts) (Watts) (Watts) ------ --------- -------- ---------1 370.0 141.7 228.3Interface Admin Oper Power
[Code]....
Cisco WAN :: 878 Default Counters Doesn't Increase To Indicate Any Traffic
Feb 11, 2011we have a 878 router and we want to mark traffics when entering on its lan interface.its lan interface is a layer 2 interface and we have created vlan interface and assosiated lan interface to that vlan.on vlan interface itself there is no service-policy command so we have to put serive-policy command on interace fast 0 itself which is layer 2 port.when we assign service-policy to fast 0 it doesnt work and it does not mark any traffic also class default counters doesnt increase to indicate any traffic is passing even it is not getting marked. ios version is advipservices.124.9T. How to mark traffic on this port. ii dont know why service-policy command is supported on layer 2 interface when it doesnt work at all.
View 3 Replies View RelatedCisco Wireless :: 4402 - DHCP Scope Increase And Changes In Wlc
Feb 6, 2013i am using wlc 4402 with a mgt ip 172.26.150.x/24 and ap manager ip 172.26.150.x/24, my all ap get the ip address from dhcp . currently in dhcp server 172.26.150.3 to 254 dhcp scope is configured. at mysite some devices are configured like ipad,iphone or galaxy tab with mac binding in dhcp server. now this pool is almost full. i have a policy configured for these devices for mac binding is done in DHCP. to increase pool what are the changes i need to do in wlc. what are the changes i need to do in dhcp server . is policy made for mac binding in dhcp server will get affected by this ?
View 2 Replies View RelatedCisco :: Increase Disk Size On LMS 4.2 Virtual Appliance
Dec 18, 2012I am low on available disk space to perform backups on my LMS 4.2 installation. Is there a way to force the appliance to recognize the increased disk space allocated by ESX VMware?
View 2 Replies View RelatedWay To Increase Local Area Connection Speed
Oct 9, 2011how to increase local area conection speed 10mbps to 100mbps?
View 2 Replies View RelatedIncrease Flash USB Modem Download Speed?
Jul 10, 2011my upload speed show 3.1MB and download speed just 11 to 70KBps is there any software to increase download speed and decrease upload speed ? i use flash USB modem for net. actually i think uplaod speed is not true speed coz at Iraq they cheating alot
View 2 Replies View RelatedServers :: Run Box Command To Increase Internet Speed?
Nov 5, 2011what i type in run box to increase INTERNET speed i saw my net provider doing this just little bit time he just type in run box ping o (.......................)/ and some numbers like IP address and then black window opened and INTERNET speed increase tell me what i type in my run box to increase speed.
View 2 Replies View Related