Cisco Switching/Routing :: Setup And 1000BASE-T SFP Transceiver Module
Feb 17, 2013
We are looking to purchase some addidtional 48 port swithches for our network. Currently we have the following swtiches setup
2 of 3750 POE-24 (These two are stacked and have our servers plugged into them). Currently no SFP modules.
3 of 3560 POE-24 (These each have two 1000BASE-T SFP modules in them, with UTP connecting back to the 3750 switches above)
We are looking to get 2 of 48 port C2960S-48TS-L switches with two 1000BASE-T SFP modules in each that then will also connect back to the 3750 switches.
I had a few of question about this:
Will the cisco lite version (rather than the more expensive cisco base software) support the 1000BASE-T SFP modules?
The 1000BASE-T SFP modules, are they auto-config? Have you the link for commands we can use, if required?
We don't have budget for stack modules, apart from that would you recommend we change anything with the new setup?
View 2 Replies
ADVERTISEMENT
Nov 13, 2011
I'm unable to get the N7K-M108X2-12L 10 Gbps Ethernet XL Module within our Nexus 7009 chassis to recognise the individual X2-10GB-SR transceiver modules. I have the same issue on another 7009 chassis.If I perform a 'show interface'. I get the following output saying SFP not inserted.
-Ethernet3/5 is down (SFP not inserted)
-Dedicated Interface
-Belongs to Po51
-Hardware: 10000 Ethernet, address: 7081.0599.d458 (bia 7081.0599.d458)
I also get the same result if I issue the following command. Are their any additional features I need to enable? or would this be a license issue?
Have already tried different X2-10GB-SR modules, reloading the card, re seating the card. [code]
View 6 Replies
View Related
May 6, 2013
I will like to know if I can replace a 1gi fiber transceiver for a 10 Gi transceiver, without any changes on the switch config.the switch is a 3750G.
View 4 Replies
View Related
Dec 19, 2012
I wonder if Cisco 1000BASE-T SFP can work with CAT-6 cable. I believe it can. But in the Cisco datasheet, it only mentions that “The 1000BASE-T SFP operates on standard Category 5 unshielded twisted pair copper cabling of up to 100m (328 ft) link length”.
View 3 Replies
View Related
Dec 31, 2012
Unforunately I have not been able to find any IOS version requirement for a brand-new 1000BASE-LX10 SFP (MGBLH1) in the internet.
The IOS version in use on this stack is:Cisco IOS Software, C3750 Software (C3750-IPBASEK9-M), Version 12.2(55)SE6, RELEASE SOFTWARE (fc1)
[Code]...
I have searched for this error and beside a third-party module (this is a Cisco SFP) the reason could be that newer IOS version is required. Before I'll request an IOS update to the stack with our internal team, IOS version required for this module to run properly and maybe a link to an overview to lookup such requirements in the future.
View 5 Replies
View Related
Jun 14, 2012
[URL]
To do that I would like to be able to sniff the traffic traversing our 7k. However, as the 7k doesn't support remote span we have to span locally. This means that I have to connect a pc to the Nexus and sent the span output to that port. However, our 7K is only equipped with N7K-M108X2-12L modules, which contains X2 10G ports. I found the CVR-X2-SFP10G X2 to SFP+ convertor module, but I wonder whether this supports a 1G copper SFP. If it doesn't it would be wasteful to buy one. On the page concerning the module I only found 10G fiber sfp's which are supported.
View 8 Replies
View Related
Dec 18, 2011
I am looking for optical transceivers that are compatible with the Cisco 5509 switch. Preferably 1G.
View 3 Replies
View Related
Feb 7, 2012
Does the X2-10GB-T copper transceiver is supported on the WS-X45-SUP6L supervisor?
View 1 Replies
View Related
Jun 18, 2012
I have the follow error in a SW3750:
%SFF8472-5-THRESHOLD_VIOLATION: Te2/0/1: Voltage low alarm; Operating value: 0.00 V, Threshold value: 3.07 V.
I used the command:
#sho interfaces transceiver
If device is externally calibrated, only calibrated values are printed.
++ : high alarm, + : high warning, - : low warning, -- : low alarm.
NA or N/A: not applicable, Tx: transmit, Rx: receive.
[Code]....
View 1 Replies
View Related
Jul 30, 2012
When I insert the TwinGig Converter in a Catalyst 4900M you get the following error message: Failed to read transceiver serial eeprom on port Te2/1, try reinserting.This error is probably because the device expects 10Gig transceivers to be connected to the device not 1Gig.I used the TwinGig 4 module and 8 SFP ports are connected. But when i type in the the "hw-module module <slot> port-group <group> select gigabitethernet" the command is not available. [code]
View 1 Replies
View Related
Sep 22, 2011
I have a catalyst 4506 switch with one sup-engine WS-X45-SUP6 L-E, which consist of two X2-10GB-SR Transceiver( CISCO).IOS on the sup-engine is cat4500e-ipbase-mz.150-2.SG1.bin. IOS detected only one X2-10GB-SR Transceiver in Ten1/2. When I insert the X2-10GB-SR Transceiver in Ten1/1
C4K_GLMMAN-3-X2PLUGGABLESEEPROMREADFAILED: Failed to read seeprom on port Te1/1. Reinsert X2 m
But the problem is i need two X2-10GB-SR Transceiver for Uplink.
View 3 Replies
View Related
Oct 15, 2012
I want to connect a Cisco small business switch (sf302-8) to a Cisco catalyst 2960S over a multi mode fiber. The transceiver I am using in the catalyst is a GLC-SX-MM. I presume in the SF302, I will have to use a MGBSX1. My question is "are these transceiver compatible with each other and if not, is there a transceiver that will suit both pieces of hardware?
View 2 Replies
View Related
Dec 9, 2012
I have a Cisco 5548 Nexus switch with 10Gbase-SR interface transceiver. This interface is connected to Server chasis.
The show interface transceiver details output shows High ++ alarm for Current. Additionally, i am getting output errors on this interface.
View 1 Replies
View Related
Oct 4, 2012
I am struggling to find an SFP transceiver, single mode, that operates at 100Mbps in a 1000Mbps port in an ME3600 or ME3800.
View 5 Replies
View Related
Jun 10, 2013
i have a cisco router (3900 series) and a add on module (4 x 1 Gig port module). For some reason i cant seem to port channel them and cant do routing (can set an ip address on those ports). I can do port channel and routing on on-board ports. Do i have to enable any commands to do this ?
View 3 Replies
View Related
Jun 24, 2012
Was wondering if anyone has ever hot ADDED, not swapped, an expansion module in a 5548up. Is a switch reboot required?I looked at the H/W install guide and it does not mention anything.
View 3 Replies
View Related
Dec 3, 2011
My C6506 USING ws-sup720-3B, i upgrade the IOS to the latest release of 12.2(33) SXJ1 IOS version. After upgrade and reload the machine got one module cannot be detect..WS-X6416-GE-MT, 16 port 1000mb MTRK ethernet module. The version of this are:
-HW 1.0
-FW 5.3 (1)1
-SW 8.5 (0.46) RFW
Question 1: Any tools available on cisco to check out the hardware/software compabiity feature?
Question 2: Any release note, compability matrix table etc resources.
View 1 Replies
View Related
Sep 4, 2012
Recently we ha a Nexus 7010 with a module frozen that was OIR (Online Remote and Insert) but do not work until reload the Nexus 7k.The command "show tech-support" has the following:
exception information --- exception instance 64 ----
Module Slot Number: 1
Device id : 147
Device Name: 0x93
Device Errorcode: 0x9329201
[code].....
Was is Excessive Interrupt Events? Can this "Minor Error" frozen the system?Is the port 42 on module 1 affected? o was 42 ports?
View 2 Replies
View Related
Jun 25, 2012
Can the encryption module (DES/ 3DES/AES/SSL VPN Encrytion/compression) for Cisco Router 3845 able to support the external connection from other high end router, for example cisco 7200? What is the maximum bandwidth, load and concurrent connection it can support?
View 1 Replies
View Related
Feb 3, 2013
why is not possible to put a WS-X4712-SFP+E - module into an R-E chassis?The module has the same connection to backplane as the WS-X4748-UPOE+E and this one works in a R-E chassis.I know the restriction of Cisco that the 4712 is only supported in 4503-E, 4506-E,4507+E and 4510+E, but why?Are there hardware-restrictions, is the backplane different?
View 2 Replies
View Related
Sep 10, 2012
I have a pair of 6509-E Switches running VS-720 Supervisors. We are planning to add Ace Module onto the 6509-E. Will IP Base Image suffice the requirement? Will Ace Module work with only IP Base Image?
View 1 Replies
View Related
Dec 16, 2012
Hot ADDED, not swapped, an expansion module in a 5548up. Is a switch reboot required?
View 2 Replies
View Related
Jan 6, 2013
Do you have any document that states whether WS-X4606-X2-E module is hot swappable or not?
View 2 Replies
View Related
Feb 20, 2012
confirm the C3KX-NM-10G module is hot-swappable.i have checked the cisco's website and it says " Although network modules are hot-swappable, we recommend installing a network module before powering the switch"
What steps i need to follow to install the module?
View 5 Replies
View Related
Apr 12, 2012
Using the new SUP-2T, need to clarify one query. If we are using the new SUP-2T in VSS mode, will the new ASA service module and NAM-3 are supported? From Cisco site, ASA module FAQ:
Q. Will the ASA Services Module support the Cisco Catalyst Virtual Switching System (VSS) at FCS?
A. Yes, depending on which supervisor you use. The ASA Services Module supports VSS either as a single firewall or as a failover pair of firewalls, when used with the Supervisor 720-10G (VS-S720-10G-3C and VS-S720-10G-3CXL). Transparent and multi- context modes also work with the VSS in this configuration. However, though the SUP 720-3B (WS-SUP720-3B and WS-SUP720-3BXL) is supported by the ASA Services Module, it is not capable of supporting the VSS. No reference to Supervisor-2T.
View 2 Replies
View Related
May 4, 2013
switch 6506 E with supp 720 does it support 10 GIG module ?
View 3 Replies
View Related
Jan 4, 2012
I have a client whom has a 4900M switch as their SAN switch. They are getting ready to upgrade their SAN to use 10G.I had quoted them a price for an X2 module, but I am unclear based on pictures I have seen of the part number
X2-10GB-SR
whether or not the X2 module plugs into the X2 slot on the switch, AND then also has to have a transceiver put in it to receive the SC ends of the Fiber jumper, or whether the SC ends of the fiber jumper plug into the X2 module directly.
View 5 Replies
View Related
Mar 4, 2012
I have a switch Cisco WS-C6509-E WS-X6716-10G-3C module ( module for 10 GB) , i have the IOS s72033-ipservicesk9-mz.122-18.SXF9.bin. I want to know if this IOS can support this module or not ? or , if i must do a upgrade , is that the IOS : "s72033-ipservicesk9_wan-mz.122-33.SXH8" work fine ?
View 7 Replies
View Related
Aug 24, 2012
i have a cisco Netowtk Analysis module installed on a 6513 core switch which is NAM-1, the version on the NAM is 5.1 and we need to upgrade to the latest version which is 5.1(2)
View 1 Replies
View Related
Mar 10, 2013
we are planning to implement a VSS solution with a 6500 series switches with sup 2T. We also need to include an ASA service module on the design, however the budget is not enough to buy two asa service modules. So i want to know if is possible run a VSS cluster, whit only one ASA service Module. and also i would like know what happens if the single ASA service module fails? can the switch cluster continue operating just as if there is not a firewall installed?
View 1 Replies
View Related
Mar 3, 2013
I have a brand new 3650x switch that I was configuring via console and left it on overnight; this was friday night ( I forgot to keep the air conditioner on). When I returned Sunday afternoon and checked the switch I realized that the SYS and STAT lights on the front were not on, however the Leds on the PS module were still on. I powered it down and turn it on again but still there are no lights on the front. The PS OK and AC OK leds on the PS module are on but I noticed the leds on the two fan modules are not green or even amber; they are off.When I first turned on the switch I remembered distinctly that there were loud noice and if all fans were in overdrive mode for a few seconds then the went to normal. I'm not gettgin this loud noise phenomenom.
View 9 Replies
View Related
Oct 31, 2012
Can Nexus 5596 support more than 1 N55-M160L3-V2 layer 3 module?
View 4 Replies
View Related
Jan 28, 2013
its a hardware problem or just not get power to module 1 for module WS-X6748-GE-TX? this is the capture from show module and sh log :
------------------ show module ------------------
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX xxx
5 2 Route Switch Processor 720 (Active) RSP720-3CXL-GE xxx
Mod MAC addresses Hw Fw Sw Status
[code].....
View 4 Replies
View Related