Cisco Switching/Routing :: 1000BASE-LX10 - SFP IOS Version Requirement?
Dec 31, 2012
Unforunately I have not been able to find any IOS version requirement for a brand-new 1000BASE-LX10 SFP (MGBLH1) in the internet.
The IOS version in use on this stack is:Cisco IOS Software, C3750 Software (C3750-IPBASEK9-M), Version 12.2(55)SE6, RELEASE SOFTWARE (fc1)
[Code]...
I have searched for this error and beside a third-party module (this is a Cisco SFP) the reason could be that newer IOS version is required. Before I'll request an IOS update to the stack with our internal team, IOS version required for this module to run properly and maybe a link to an overview to lookup such requirements in the future.
View 5 Replies
ADVERTISEMENT
Dec 19, 2012
I wonder if Cisco 1000BASE-T SFP can work with CAT-6 cable. I believe it can. But in the Cisco datasheet, it only mentions that “The 1000BASE-T SFP operates on standard Category 5 unshielded twisted pair copper cabling of up to 100m (328 ft) link length”.
View 3 Replies
View Related
Feb 17, 2013
We are looking to purchase some addidtional 48 port swithches for our network. Currently we have the following swtiches setup
2 of 3750 POE-24 (These two are stacked and have our servers plugged into them). Currently no SFP modules.
3 of 3560 POE-24 (These each have two 1000BASE-T SFP modules in them, with UTP connecting back to the 3750 switches above)
We are looking to get 2 of 48 port C2960S-48TS-L switches with two 1000BASE-T SFP modules in each that then will also connect back to the 3750 switches.
I had a few of question about this:
Will the cisco lite version (rather than the more expensive cisco base software) support the 1000BASE-T SFP modules?
The 1000BASE-T SFP modules, are they auto-config? Have you the link for commands we can use, if required?
We don't have budget for stack modules, apart from that would you recommend we change anything with the new setup?
View 2 Replies
View Related
Jun 14, 2012
[URL]
To do that I would like to be able to sniff the traffic traversing our 7k. However, as the 7k doesn't support remote span we have to span locally. This means that I have to connect a pc to the Nexus and sent the span output to that port. However, our 7K is only equipped with N7K-M108X2-12L modules, which contains X2 10G ports. I found the CVR-X2-SFP10G X2 to SFP+ convertor module, but I wonder whether this supports a 1G copper SFP. If it doesn't it would be wasteful to buy one. On the page concerning the module I only found 10G fiber sfp's which are supported.
View 8 Replies
View Related
Jun 2, 2013
I am looking the power requirement for 6506E in data sheet and it shows that is support 3000, 4000, 6000 & 8700W. I have currentely 4000W power source for my new 6506E switch. will it work with below modules in new 6506e ?
View 2 Replies
View Related
Nov 9, 2011
I have cisco 3750 with ipservices license and I am running with c3750e-universal-mz.122-50.SE2. And I would like to upgrade the IOS " k9" IOS. ie c3750e-universalk9-mz.122-50.SE2. Is there any license required for that ?Also any difference in the IOS upgrade procedure.
View 1 Replies
View Related
Mar 8, 2013
I have Catalyst 4507 R-E with one supersor engine n 3 other modules.My question is related to routing of different networks through this switch.I already have certain routes configured which are going to my ISP thru Juniper firewall.(192.168.0.9)I also have Cisco ASA 5510 which i want to use as a backup in case the first one goes down.
View 3 Replies
View Related
Apr 22, 2012
I went through the configuration guide for 4500 series switches for NSF/SSO for failover between Sup's. I just wanted to know that that are we supposed to run the SSO command on both of the supervisors? Secondly, are we only supposed to run the nsf process under EIGRP on the secondary supervisor and routing peers and not on the primary supervisor?
View 2 Replies
View Related
Oct 2, 2012
I am using Cisco 2911 & IOS version is 15.1. My problem is that after some days (e.g. 15-20 days), the routing table suddenly stops updating & then I have to enter the default route again to make it up. I am using Track 1 to track default route here. After primary link goes down, the Track is also going down but after coming the primary link up, the track is not coming up. So, I have to add the default route again to make it up.
View 2 Replies
View Related
Apr 7, 2013
Is there a way I can check the version of each device on two Cisco 6509 if they are Virtually connected (VSS)? When I enter the command show version, it only shows one result, unlike show module, you have an option to choose which switch by entering 1 or 2.
View 3 Replies
View Related
Nov 13, 2007
im trying to find out what is the latest ios version for 3500xl switch for upgrade it .
View 4 Replies
View Related
Apr 23, 2013
On the downloads page there's a 9.0.2.ED listed as the 'latest' but then if I expand the '9' below it I get to 9.1.1.ED. Which one is the actual latest? is there any way to tell the one that is not an 'interim' version I think 9.1.1 is also listed under interim?
View 4 Replies
View Related
Apr 25, 2012
I purchased several Cisco 2811 with Advanced IP Services - they are version 12.2.X
The product number looked like this
CISCO2811-HSEC/K9 2811 Bundle w/AIM-VPN/SSL-2,Adv IP Serv,10 SSL lic,128F/512D
I need to upgrade the IOS to version 15.1 - Do I require a license ? What happens if I install it without a License ? Am I entitled to a free license as I am not changing the software type (ADV IP Serv) ?
View 2 Replies
View Related
Sep 26, 2012
what should it be the minimum IOS version that I require on my WS-C6509-E equipments to support "logging origin-id" command?
Cisco documentation says that this command was introduced in 12.2(15)T, and integrated into 12.2(33)SXH.
BUT my Cisco switches have 12.2(33)SXH5 IOS version......and they do not support "logging origin-id".
(config)#logging ? Hostname or A.B.C.D IP address of the logging host buffered Set buffered logging parameters buginf Enable buginf logging for debugging cns-events Set CNS Event logging level console Set console logging parameters count Count every log message and timestamp last occurance esm Set ESM filter restrictions event Global interface events exception Limit(code)
View 2 Replies
View Related
May 7, 2012
I have this 4900M running version 12.2(54)SG1. I the log I get this 3 lines:
May 8 08:32:15: %C4K_SWITCHINGENGINEMAN-4-TCAMINTERRUPT: (Suppressed 429 times)flCam0 aPErr interrupt. errAddr: 0xC48 dPErr: 1 mPErr: 0 valid: 1
May 8 08:32:24: %C4K_L3HWFORWARDING-4-FLTCAMPARITYERROR: (Suppressed 866 times)FL Tcam Perr with no FwdEntry Hw index: 3144 Hw entry: Sw entry:
May 8 08:32:45: %C4K_SWITCHINGENGINEMAN-4-TCAMINTERRUPT: (Suppressed 432 times)flCam0 aPErr interrupt. errAddr: 0xC48 dPErr: 1 mPErr: 0 valid: 1
They seems to be coming on regular basis, repeating every minute. I've tried Google and the most relevant info I can find is this {URL}. But it says "Upgrade software to IOS version 12.2(52)SG or later OR 12.2(50)SG4 or later. ". I'm already running 12.2(54), so why does this 3 line repeatedly show up in the log every minute.
View 2 Replies
View Related
Mar 28, 2011
I have two desktop PCs connected via PRO/100VE LAN and am about to replace one of these with a desktop that has Integrated 10/100/1000Base-T. Will the two machines be able to communicate? One machine will use XP Home and the new machine Windows 7.
View 2 Replies
View Related
Aug 23, 2012
I need to confirm that the 4510R+E switch with the SUB7-E/2 running version 15 IOS will not support NAT. I am 99% convinced that it does not but i am looking for confirmation, as i am a bit surprised by the lack of NAT support on this platform.
View 0 Replies
View Related
Jul 10, 2012
Which IOS version for me3600 supports 4-byte BGP?
View 1 Replies
View Related
Jan 11, 2012
I wonder whethere it is possible to check the the IOS version on the standby sup720 of a 6500? if yes, what command would you use?
View 5 Replies
View Related
Jan 14, 2013
I have a customer with a stack of two switches C2960S-24TS-L that are running 12.2(58)SE2 universal K9, we see that the CPU load increase over time, to 95% and stays there reload solves the problem.the process that akes a lot of CPU is also the SNMP ENGINE, I see that it is running 30 minutes on 95% and then 10 minutes on 35%, this is the only stack were we see this problem. Is there also a SNMP bug in this version ?
View 1 Replies
View Related
Dec 19, 2012
i want to know of the IOS verstion of cisco switch which support STP,some one told me that this feature is activated by deafalut if it not activated,how to turn on this Feature.i am using cisco 2960 Switch.
View 2 Replies
View Related
Apr 4, 2011
I have 8 switches (different models) configured in stack:
Switch Ports Model SW Version SW Image------ ----- ----- ---------- ---------- 1 28 WS-C3750G-24TS-1U 12.2(55)SE C3750-IPSERVICESK9-M 2 26 WS-C3750-24P 12.2(55)SE C3750-IPSERVICESK9-M 3 30 WS-C3750X-24P 12.2(55)SE C3750E-UNIVERSALK9-M 4 30 WS-C3750X-24P 12.2(55)SE C3750E-UNIVERSALK9-M* 5 12 WS-C3750G-12S 12.2(55)SE C3750-IPSERVICESK9-M 6 30 WS-C3750E-24PD 12.2(55)SE C3750E-UNIVERSALK9-M 7 30 WS-C3750E-24PD 12.2(55)SE C3750E-UNIVERSALK9-M 8 30 WS-C3750X-24P 12.2(55)SE C3750E-UNIVERSALK9-M
Now I'm have IOS ver. 12.2(55)SE but from time to time I'm experiencing strange system freezing. It means that all systems connected to the stack are working very, very slow. It hapens ones, sometimes twice a month and takes 5 minutes. I didn't find anything strange in logs (neither on switch nor router). I would like to install other IOS version. Could you recomend me the most stable version for this stack (built from these different models) ?And the secound question: - Is it possible to copy SE1 manualy to every switch and reload one by one manualy. Will they join the stack and work fine after reload or maybe there will be a IOS mismatch ?
View 10 Replies
View Related
Jan 23, 2012
We are close to receiving our new 6513E chassis which I will be running Sup720 cards in. This will be replacing our existing 6509 Sup2 setup in production. What current IOS version should I run on the Sup720 ? I would like to support SSH. The chassis will be populated with a couple of 6724 SFP cards, 2 6704 10 gig cards and a few 6748 line cards.Is there a good intitial config guide ?
View 6 Replies
View Related
Apr 28, 2013
give me a link to where I can find the minimum code version for N55-M16UP expansion card for a Nexus 5k?
View 1 Replies
View Related
Jul 2, 2012
upgrade experience with the 6509E on what IOS version to use. This is a new install, so I want the most current version that supports SSH and works with dual supervisors.
Here is some information:
WS-C5609-E with 983008K/65536K bytes of memory
Current version 12.2(18)SXF17b
Slot 5 Supervisor 720 (Active)
Slot 6 Supervisor 720 (Hot)
Just need a strong base code, no advanced services. Let me know if you any additional information.
View 2 Replies
View Related
Mar 25, 2012
I change only a chasis in a router 3845, but the "show version" command should be the same , except for the serial number and other parameter of time.. however, the number of serial interface change from 4 up to 2.The hardware module of 3845 are 3.
1.- VWIC E1/T1 with 2 port
2.- Fastethernet 36 port
3.- Supervisor engine with 2 Gigabit port
View 7 Replies
View Related
Nov 24, 2012
i have a big problem because i configure a vlans with vrf and HSRP but, when i do "show hsrp brief", dont show this interfaces and, i can ping virtual IP. it seems hsrp dont work.
SWSERVSCAMILO_N7010_A#
interface Vlan405
description smsc-fwatlas1
no shutdown
[Code] ....
View 1 Replies
View Related
Feb 26, 2013
I have a 2 Cisco 3750X stacked working as CORE switches but not in production yet showing a high CPU utilization and I would like to see with you whether you think this is normal or a IOS upgrade/downgrade should be performed.
I have very low traffic coming through as this is not yet in production:
122222333331111122222222222222222222222221111122222222222222 933333999999999922222777772222277777333339999922222111111111 100 90 80 70 60 50 40 ***** 30 ***** ***** ***** 20 ********************************************************** 10
[Code].....
View 4 Replies
View Related
Jun 3, 2012
I have several older 2950's running on my network. This one in particular became of interest to me because I couldn't set up SSH on it or enable any QoS features on it, so I did some research. What I found was there are basically 2 versions of the IOS, c2950-i6q4l2 or c2950-i6k2l2q4. I also read that the c2950-i6q4l2 IOS versions (like the one in the switch I am referring to) have both the SI and EI feature sets integrated, but the one that gets enabled is entirely dependent upon the switch model you are running it on. Did I understand this correctly? Does the IOS check the hardware on the switch and then decide with feature set to use? If so, what is prohibiting the EI feature set from being enabled on this switch? Is there a way to force the EI feature set to be enabled since it is integrated in this image?
Cisco Internetwork Operating System Software
IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(22)EA12, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2008 by cisco Systems, Inc.
Compiled Mon 07-Jul-08 23:39 by amvarma
Image text-base: 0x80010000, data-base: 0x80570000
[code]....
View 8 Replies
View Related
Feb 18, 2013
I'm able to upgrade the master of a 3750 stack, but the member fails to upgrade. [code] I couldn't do rmdir flash:update unless I reload chassis... but even after reloading still cannot make the 2nd member to load with the newer IOS.
View 3 Replies
View Related
Dec 10, 2012
know if Private Vlans are supported on the Cisco 4900m switch when set in VTP version 3 and VTP disabled?Most documents just specify VTY transparent mode without mentioning the version, trying not to assume since this is production.
View 1 Replies
View Related
May 30, 2013
I am going to upgrade a number of catalyst 2960s-switcher to the latest IOS- version. The best solution for me would be if all the switches could be reloaded at the same time to shorten the maintenance-windows. So my question is: If I run the upgrade (archive down load -sw) before the maintenance-windows WITHOUT the reload-option, will then the switches continue to run without interruptions with the current IOS- version and config until I run reload manually?
View 3 Replies
View Related
Oct 19, 2012
Trying to configure 1811w for wi fi . Need to use authentication shared keys but current IOS seems does not support ir
Router(config)#int dot11Radio 0
Router(config-if)#ssid manvee1
Router(config-if-ssid)#a?
% Unrecognized command
Router(config-if-ssid)#
(C181X-ADVIPSERVICESK9-M), Version 12.4(24)T8.
Need to know which IOS will support wi fi and authentication command under dot11 radio 0?
View 4 Replies
View Related
