Cisco Switching/Routing :: Minimum Code Version For N55-M16UP?
Apr 28, 2013give me a link to where I can find the minimum code version for N55-M16UP expansion card for a Nexus 5k?
View 1 Replies
ADVERTISEMENT
Cisco Switching/Routing :: What Should Be Minimum IOS Version On WS-C6509-E
Sep 26, 2012what should it be the minimum IOS version that I require on my WS-C6509-E equipments to support "logging origin-id" command?
Cisco documentation says that this command was introduced in 12.2(15)T, and integrated into 12.2(33)SXH.
BUT my Cisco switches have 12.2(33)SXH5 IOS version......and they do not support "logging origin-id".
(config)#logging ? Hostname or A.B.C.D IP address of the logging host buffered Set buffered logging parameters buginf Enable buginf logging for debugging cns-events Set CNS Event logging level console Set console logging parameters count Count every log message and timestamp last occurance esm Set ESM filter restrictions event Global interface events exception Limit(code)
Cisco Wireless :: Maximum Code Level For Lightweight 1130 / Minimum WLC Code For 1600 Series APs?
Feb 19, 2013I have been searching through the cisco docs for a while and i just cant seem to find this info. Can I run aironet 1600's with my wism running 7.0.116? Also, could I run my 1130 series ap's with a wism2? Basically, what is the minimum code level for a lightweight 1600, and what is the maximum code level for a lightweight 1130?
View 3 Replies View RelatedCisco Switching/Routing :: N55 M16UP Module In Nx5548up
Jun 24, 2012Was wondering if anyone has ever hot ADDED, not swapped, an expansion module in a 5548up. Is a switch reboot required?I looked at the H/W install guide and it does not mention anything.
View 3 Replies View RelatedCisco Switching/Routing :: Hot Add - N55 M16UP Module In NX5548up?
Dec 16, 2012Hot ADDED, not swapped, an expansion module in a 5548up. Is a switch reboot required?
View 2 Replies View RelatedCisco Wireless :: AIR-CAP1552I - Minimum WISM Support Code?
Feb 15, 2012I am looking to install 2 1552I outdoor AP's. I can't find what the minimum code version is on the WISM controller that supports this AP.I am running 7.0.98.0 on the WISM. Where can I find this information?
View 4 Replies View RelatedCisco Switching/Routing :: Minimum UPS For Catalyst 3560G-48-Poe?
Oct 2, 2012We have 2 catalyst 3560g-48-PoE protected by a 1000Va 800Watt tripp-lite and I was cheking to see if that is really sufficient. Looking at the charts from Cisco suppport I would think I should have more, but have not had any issues with a few power outages
View 1 Replies View RelatedCisco Switching/Routing :: Minimum Power / Voltage Of Switch 3750
May 20, 2013I want to know how much minimum power required for swicth catalyst 3750.I want to know cause in my building place, the power in unstable so it make my switch corrupt/damage even i add power consistancy....
How much amount power to the ups and ups to switch?
Cisco Switching/Routing :: Possible To1941 Security Bundle Router Support Minimum Of 2k Of VLAN ID
Dec 17, 2012Is it possible to cisco 1941 security bundle router Support minimum of 2k of VLANs ID and shall support upto 60 vlans?
View 4 Replies View RelatedCisco Wireless :: 1142 What Version Of Code To Be Used
Dec 9, 2012I need to convert some 1142 APs to lightweight mode. They will connect to controllers running 7.3.101.0. I noticed there's two options of Lightweight IOS code available c1140-k9w8-tar.152-2.JA.tar and c1140-rcvk9w8-tar.152-2.JA.tar. Whats the difference between the two versions of code?
View 4 Replies View RelatedCisco Wireless :: WLC 2504 Needs Which Code Version?
Apr 23, 2013Just purchased a 2504 w/15 licenses and to run 10 - 2602i AP's. Code out of the box is 7.0.222.0 but when I go the support site I see 7.2, 7.3 and 7.4 all with relatively recent dates. I found I need 7.2.110.0 at a minimum to run the AP's. All the code versions say ED, which I thought was not final release versions.
View 1 Replies View RelatedCisco Application :: What Version Of Code Are Supported On ACE20
Mar 18, 2012I see several code versions that seem to support on ACE30.Is A2.3.4 Or A2(3.5) that latest version for ACE20-MOD-9?Will the version 4 or 5 run on ACE20?I currently user A2(3).
View 3 Replies View RelatedCisco Firewall :: 5510 Code Version Upgrade?
Feb 3, 2013I am looking to upgrade a 5510 that is currently on code version 8.0(4) to code version 9.1. I know I will have to upgrade to 1gb ram, but can i just upgrade straight to version 9.1 or do I need to follow an upgrade path? This is a standalone device so I am planning on downtime.
View 8 Replies View RelatedCisco WAN :: ASR 1002 Fixed Stable Code Version
Jan 22, 2013I am looking upgrade my ASR routers to a newer code. I am running asr1000rp1-advipservicesk9.03.03.01.S.151-2.S1.bin now. Would like input on what a good stable version is. I am not bleeding edge so the latest version I won't trust.
View 5 Replies View RelatedCisco Switching/Routing :: How To Know WOL Is Supported On N7K With 6.x Code And F2 Line Cards
May 11, 2012I would like to know whether WOL is supported on a N7K with 6.x code and F2 line cards. I also would like a how to for this. If it is not supported will an ip helper address to the broadcast address of the destination vlan SVI will suffice to get it workinng. If so I can restricht the forwarded broadcast to only the wol traffic.
View 1 Replies View RelatedCisco Switching/Routing :: Nexus 7K 6.1 Code And F2 Series Module - How To Enable Priority
Jul 7, 2012I have a 7K running 6.1 code, on F series line cards. I need to set it to prioritise DSCP EF marked traffic, that's all at this stage, but am unclear on the configuration steps required. The packets will already be marked, I just need to ensure they end up in a priority queue.
View 2 Replies View RelatedCisco Switching/Routing :: 3550 - Hard Code Speed And Duplex Settings
Mar 31, 2013I am trying to hard code the speed and duplex settings on interfaces gigabit 0/1 - 2 interfaces with out success.
DSW121(config)#interface range g0/1 - 02
DSW121(config-if-range)#speed ?
Nonegotiate Do not negotiate speed
[Code]...
Cisco Switching/Routing :: 2911 With IOS Version Is 15.1 - Routing Table Not Updating
Oct 2, 2012I am using Cisco 2911 & IOS version is 15.1. My problem is that after some days (e.g. 15-20 days), the routing table suddenly stops updating & then I have to enter the default route again to make it up. I am using Track 1 to track default route here. After primary link goes down, the Track is also going down but after coming the primary link up, the track is not coming up. So, I have to add the default route again to make it up.
View 2 Replies View RelatedCisco Switching/Routing :: Show Version On VSS 6509?
Apr 7, 2013Is there a way I can check the version of each device on two Cisco 6509 if they are Virtually connected (VSS)? When I enter the command show version, it only shows one result, unlike show module, you have an option to choose which switch by entering 1 or 2.
View 3 Replies View RelatedCisco Switching/Routing :: IOS Version For C3500XL Switch?
Nov 13, 2007im trying to find out what is the latest ios version for 3500xl switch for upgrade it .
View 4 Replies View RelatedCisco Switching/Routing :: 5505 Latest OS Version - 9.0.2 Or 9.1.1?
Apr 23, 2013On the downloads page there's a 9.0.2.ED listed as the 'latest' but then if I expand the '9' below it I get to 9.1.1.ED. Which one is the actual latest? is there any way to tell the one that is not an 'interim' version I think 9.1.1 is also listed under interim?
View 4 Replies View RelatedCisco Switching/Routing :: Upgrading IOS On 2811 From Version 12.2.X To 15
Apr 25, 2012I purchased several Cisco 2811 with Advanced IP Services - they are version 12.2.X
The product number looked like this
CISCO2811-HSEC/K9 2811 Bundle w/AIM-VPN/SSL-2,Adv IP Serv,10 SSL lic,128F/512D
I need to upgrade the IOS to version 15.1 - Do I require a license ? What happens if I install it without a License ? Am I entitled to a free license as I am not changing the software type (ADV IP Serv) ?
Cisco Switching/Routing :: 4900M - Upgrade IOS Version
May 7, 2012I have this 4900M running version 12.2(54)SG1. I the log I get this 3 lines:
May 8 08:32:15: %C4K_SWITCHINGENGINEMAN-4-TCAMINTERRUPT: (Suppressed 429 times)flCam0 aPErr interrupt. errAddr: 0xC48 dPErr: 1 mPErr: 0 valid: 1
May 8 08:32:24: %C4K_L3HWFORWARDING-4-FLTCAMPARITYERROR: (Suppressed 866 times)FL Tcam Perr with no FwdEntry Hw index: 3144 Hw entry: Sw entry:
May 8 08:32:45: %C4K_SWITCHINGENGINEMAN-4-TCAMINTERRUPT: (Suppressed 432 times)flCam0 aPErr interrupt. errAddr: 0xC48 dPErr: 1 mPErr: 0 valid: 1
They seems to be coming on regular basis, repeating every minute. I've tried Google and the most relevant info I can find is this {URL}. But it says "Upgrade software to IOS version 12.2(52)SG or later OR 12.2(50)SG4 or later. ". I'm already running 12.2(54), so why does this 3 line repeatedly show up in the log every minute.
Cisco Switching/Routing :: 1000BASE-LX10 - SFP IOS Version Requirement?
Dec 31, 2012Unforunately I have not been able to find any IOS version requirement for a brand-new 1000BASE-LX10 SFP (MGBLH1) in the internet.
The IOS version in use on this stack is:Cisco IOS Software, C3750 Software (C3750-IPBASEK9-M), Version 12.2(55)SE6, RELEASE SOFTWARE (fc1)
[Code]...
I have searched for this error and beside a third-party module (this is a Cisco SFP) the reason could be that newer IOS version is required. Before I'll request an IOS update to the stack with our internal team, IOS version required for this module to run properly and maybe a link to an overview to lookup such requirements in the future.
Cisco Switching/Routing :: SUB7-E/2 Running Version 15 IOS Will Not Support NAT
Aug 23, 2012I need to confirm that the 4510R+E switch with the SUB7-E/2 running version 15 IOS will not support NAT. I am 99% convinced that it does not but i am looking for confirmation, as i am a bit surprised by the lack of NAT support on this platform.
View 0 Replies View RelatedCisco Switching/Routing :: Ios Version That Supports 4 Byte BGP In Me3600
Jul 10, 2012Which IOS version for me3600 supports 4-byte BGP?
View 1 Replies View RelatedCisco Switching/Routing :: Check IOS Version On A Standby Sup On Cat6500?
Jan 11, 2012I wonder whethere it is possible to check the the IOS version on the standby sup720 of a 6500? if yes, what command would you use?
View 5 Replies View RelatedCisco Switching/Routing :: Stack C2960S High CPU Version 12.2(58)SE2
Jan 14, 2013I have a customer with a stack of two switches C2960S-24TS-L that are running 12.2(58)SE2 universal K9, we see that the CPU load increase over time, to 95% and stays there reload solves the problem.the process that akes a lot of CPU is also the SNMP ENGINE, I see that it is running 30 minutes on 95% and then 10 minutes on 35%, this is the only stack were we see this problem. Is there also a SNMP bug in this version ?
View 1 Replies View RelatedCisco Switching/Routing :: 2960 Which IOS Version Supported Stp Feature
Dec 19, 2012i want to know of the IOS verstion of cisco switch which support STP,some one told me that this feature is activated by deafalut if it not activated,how to turn on this Feature.i am using cisco 2960 Switch.
View 2 Replies View RelatedCisco Switching/Routing :: 3750 Stack - Recommended IOS Version?
Apr 4, 2011I have 8 switches (different models) configured in stack:
Switch Ports Model SW Version SW Image------ ----- ----- ---------- ---------- 1 28 WS-C3750G-24TS-1U 12.2(55)SE C3750-IPSERVICESK9-M 2 26 WS-C3750-24P 12.2(55)SE C3750-IPSERVICESK9-M 3 30 WS-C3750X-24P 12.2(55)SE C3750E-UNIVERSALK9-M 4 30 WS-C3750X-24P 12.2(55)SE C3750E-UNIVERSALK9-M* 5 12 WS-C3750G-12S 12.2(55)SE C3750-IPSERVICESK9-M 6 30 WS-C3750E-24PD 12.2(55)SE C3750E-UNIVERSALK9-M 7 30 WS-C3750E-24PD 12.2(55)SE C3750E-UNIVERSALK9-M 8 30 WS-C3750X-24P 12.2(55)SE C3750E-UNIVERSALK9-M
Now I'm have IOS ver. 12.2(55)SE but from time to time I'm experiencing strange system freezing. It means that all systems connected to the stack are working very, very slow. It hapens ones, sometimes twice a month and takes 5 minutes. I didn't find anything strange in logs (neither on switch nor router). I would like to install other IOS version. Could you recomend me the most stable version for this stack (built from these different models) ?And the secound question: - Is it possible to copy SE1 manualy to every switch and reload one by one manualy. Will they join the stack and work fine after reload or maybe there will be a IOS mismatch ?
Cisco Switching/Routing :: 6513E What Current IOS Version Should Run On Sup720
Jan 23, 2012We are close to receiving our new 6513E chassis which I will be running Sup720 cards in. This will be replacing our existing 6509 Sup2 setup in production. What current IOS version should I run on the Sup720 ? I would like to support SSH. The chassis will be populated with a couple of 6724 SFP cards, 2 6704 10 gig cards and a few 6748 line cards.Is there a good intitial config guide ?
View 6 Replies View RelatedCisco Switching/Routing :: Best Current Stable IOS Version For 6509E?
Jul 2, 2012upgrade experience with the 6509E on what IOS version to use. This is a new install, so I want the most current version that supports SSH and works with dual supervisors.
Here is some information:
WS-C5609-E with 983008K/65536K bytes of memory
Current version 12.2(18)SXF17b
Slot 5 Supervisor 720 (Active)
Slot 6 Supervisor 720 (Hot)
Just need a strong base code, no advanced services. Let me know if you any additional information.
Cisco Switching/Routing :: 3845 Show Version Interpretation
Mar 25, 2012I change only a chasis in a router 3845, but the "show version" command should be the same , except for the serial number and other parameter of time.. however, the number of serial interface change from 4 up to 2.The hardware module of 3845 are 3.
1.- VWIC E1/T1 with 2 port
2.- Fastethernet 36 port
3.- Supervisor engine with 2 Gigabit port