I am looking upgrade my ASR routers to a newer code. I am running asr1000rp1-advipservicesk9.03.03.01.S.151-2.S1.bin now. Would like input on what a good stable version is. I am not bleeding edge so the latest version I won't trust.
View 5 RepliesI've had the DIR-655 for a few months now, along with a Motorola Surfboard sb6121 DOCSIS 3.0.Modem works fine, the router was working perfectly fine until recently last week.
I have a desktop hardwired and a wireless network going on that I use just for my mobile phone and tablet at times. At first I was having disconnection problems with my wireless, then noticed a neighbor installed a similar router in the area according to my wifi analyzer, so I changed the channels and my wireless started working great. During this process I also did a firmware update and since then I've been receiving some really poor browsing problems, sometimes I'll visit websites like Facebook, or a news website, and it'll say something about the DNS not working, (at this point I'll ping the website and it still pings fine without any loss) so I'll visit the website about 10 minutes later and it works great. I've done extensive research on forums/Google and found it must link up to the new firmware update and something about a DNS relay? My version is: Hardware Version: B1 Firmware Version: 2.10NA
In other words, is there a way I can fix this issue from disconnecting without having to downgrade back to the old firmware? Or is this a common issue they'll continue to happen? If I do downgrade, HOW do I downgrade back to the stable version?
upgrade experience with the 6509E on what IOS version to use. This is a new install, so I want the most current version that supports SSH and works with dual supervisors.
Here is some information:
WS-C5609-E with 983008K/65536K bytes of memory
Current version 12.2(18)SXF17b
Slot 5 Supervisor 720 (Active)
Slot 6 Supervisor 720 (Hot)
Just need a strong base code, no advanced services. Let me know if you any additional information.
I have Cisco 6513 with sup720 running s72033-adventerprisek9_wan-mz.122-18.SXF8.bin. I would like to upgrade with the latest and stable IOS.
View 5 Replies View RelatedLooking for a recommended code on the ASA 5585x firewall. We ran into a bug (CSCtr24705) on version 8.4.2 where it rebooted the primary firewall. The bug has to do with modifying an existing ACL that's part of a custom policy-map inside a service-policy. If we upgrade to 8.4.5 (which has the previous bug fix in it), there is another major bug (CSCud70273) where if you use the packet-tracer input command on an inside interface it causes problems too.
I don't understand why packet-tracer input would have a bug associated with it when it's been around for a long time and we use it on a daily basis for troubleshooting. Is there stable code for the 5585x to upgrade to without running into possibly a major bug? This is our core firewall so there are no VPN tunnels on it. It's setup in active/standby failover in routed mode.
I need to convert some 1142 APs to lightweight mode. They will connect to controllers running 7.3.101.0. I noticed there's two options of Lightweight IOS code available c1140-k9w8-tar.152-2.JA.tar and c1140-rcvk9w8-tar.152-2.JA.tar. Whats the difference between the two versions of code?
View 4 Replies View RelatedJust purchased a 2504 w/15 licenses and to run 10 - 2602i AP's. Code out of the box is 7.0.222.0 but when I go the support site I see 7.2, 7.3 and 7.4 all with relatively recent dates. I found I need 7.2.110.0 at a minimum to run the AP's. All the code versions say ED, which I thought was not final release versions.
View 1 Replies View RelatedI see several code versions that seem to support on ACE30.Is A2.3.4 Or A2(3.5) that latest version for ACE20-MOD-9?Will the version 4 or 5 run on ACE20?I currently user A2(3).
View 3 Replies View RelatedI am looking to upgrade a 5510 that is currently on code version 8.0(4) to code version 9.1. I know I will have to upgrade to 1gb ram, but can i just upgrade straight to version 9.1 or do I need to follow an upgrade path? This is a standalone device so I am planning on downtime.
View 8 Replies View Relatedgive me a link to where I can find the minimum code version for N55-M16UP expansion card for a Nexus 5k?
View 1 Replies View RelatedI have been searching through the cisco docs for a while and i just cant seem to find this info. Can I run aironet 1600's with my wism running 7.0.116? Also, could I run my 1130 series ap's with a wism2? Basically, what is the minimum code level for a lightweight 1600, and what is the maximum code level for a lightweight 1130?
View 3 Replies View RelatedMcAffee scan of acs 1113 appliance running the 4.2 build 124 patch 12 version reports that a medium vulnerability exists because the system has SSH version 1. Any way to specify only version 2 or turn off SSH?
View 9 Replies View RelatedI want to make a small LAN, not connected to the internet. I open control panel/networking and find my Ethernet adapter. I unchecked IPv6 and click on IPv4 and select "Properties". I gave a fixed IP address of 192.168.1.1 butI can't ping 192.168.1.1
And a program I wrote can't access a MySql database on that address. I am using Xampp, the program can access the database if its connect string says localhost, not 192.168.1.1 Also, I can access through PhpMyAdmin and invoking MySql from a Dos box - so, MySql seems to be ok. Wondering why I can't ping, I run IPCONFIG and my Ethernet adapter's address is the old one, not the new fixed one that I assigned.
[UPDATE] I haven't attached a router yet, it's a stand-alone PC. Thanks for pointing out that the router, when added, will probably be 192.168.1.1 so I should probably make my PC 192.168.1.2. but my point here is that I can't ping what I thought I set as my static IP and, indeed, it does not show up when I run IPCONFIG - I get the previous value.
I have a fixed external ip address.I have port forwarding setup for accessing a NAS inside my LAN, lets say port 12345.Now when I use my laptop outside my own LAN, e.g. 99.99.99.99:12345 resolves nicely to my NAS. But when I use the same 99.99.99.99:12345 inside my LAN, it does not resolve. Instead, it gives me a 'server takes too long to answer' error
I have also setup a virtual host to an ip cam inside my network. That one resolves just fine. I tried enabling remote management on the DIR-655 and also that works fine using 99.99.99.99:8888.When I replace the external ip address with the internal ip address of my NAS, thus bypassing port forwarding, it obviously also works ok.
Why the forwarded ports are not accessible when I use my own external fixed IP address? Does the DIR-655 treat it different than other external IP addresses?
We have 2911 with HWIC-4ESW. System image file is "flash0:c2900-universalk9-mz.SPA.152-1.T1.bin"_2911#sh inv NAME: "CISCO2911/K9 chassis", DESCR: "CISCO2911/K9 chassis" PID: CISCO2911/K9 , VID: V05 , SN: FGL16011005
[Code]....
The problem was that HWIC-4ESW no longer pass traffic although showing that the interfaces are up rebooting the router solved the problem. What IOS is more stable and not subject to this problem?
I need to create several VLans on my switch.After reading the admin guide pdf, i still don't understand how to create any simple VLan.some tutorial or steps (with IE or Mozilla browser) how to create and use VLan, and to connect one VLan to another.For example,i need to create 3 VLans.
First Vlan consist of 5 ports (Vlan Name = Red)
Second Vlan consist of 15 ports (Vlan Name = Green)
Last Vlan consist of the rest of the ports (VLan Name = White)
I have a running L2TP/IPsec VPN setup with authentification against a radius server (freeradius2 witch mysql). I would like to have some of my VPN users get a fixed IP address instead of the dynamically assigned IP Pool.
The radius server is returning the correct parameters, I think.
It´s a Cisco 892 Integrated Service Router. Code...
When I read Nexus 5K install guide , I found the follow :The Cisco Nexus 5596UP switch has the following features: # •48 fixed 1- and 10-Gigabit Ethernet server connection ports on the back of the switch AND The 48 fixed ports support 8-, 4-, 2-, or 1-Gbps Fibre Channel transceivers and 1- or 10-Gigabit Ethernet transceivers. Does these is a conflict ?The 48 fixed port on this switch support only 1- and 10-Gigabit Ethernet or 8-, 4-, 2-, or 1-Gbps Fibre Channel and 1- or 10-Gigabit simultaneously ？
View 2 Replies View RelatedMy company requires each user dial-in must be a fixed IP; The old acs4 can,but I cannot find the same configration item in the ACS5.2
View 2 Replies View Related I have an ADSL connection and have configured the PPPoE subinterface on WAN1 (ADSL) this connection has a static IP, and I know that the ISP gives that to me through DHCP however I have 4 or 5 additional IP addresses also provided to me on that same link, and they are not given to me via DHCP.
How do I configure this router to have multiple fixed IP addresses on a PPPoE interface?
I also need to port forward some ports for each of the IP's but I assume this will be easy after i have the IP addresses setup.
Is the onboard interfaces on an ASR router (4x on ASAR1002, 6x on ASR1002-X) are fixed gigabit or are they 10/100/1000 ?
I assume the interfaces on the 8port Gigabit SPA module are fixed gigabit speed ports (why otherwise sell a 10/100 8port SPA module also ?) no ?
i wanted to know the reason of why my ping drops or how to make it more stable. For example i play a game called League Of Legions, which i think my connection and pc exceeds the system requirements. (Except my Video card since im using a standard which was with the MOBO.)
When im playing this game, i have a ping of 50-80, suddenly it drops to 300-500, which causes me lag (Happens multiple times in a 45min game or any). I think thats not normal, since other players dont suffer from that.
[url]....
It works fine on both my pc and wifi laptop, provided I give a fixed DNS server that was entered by my internet provider. My IP address is set to 'obtain IP address automatically' but my DNS is set to a preferred DNS by the provider. I have to set this on my notebook as well in order to access internet. If I set it to obtain DNS server automatically, internet stops working on that machine.roblem is when I try to access internet through my phone it does not work, because I have no option to enter a DNS server there. Internet works fine on my phone using another wifi router where the obtain dns address automatically is enabled.
View 1 Replies View RelatedI live in an area where there are lots of wireless modems and since most broadcast on the default frequencies, here is often interference. I'd like to set my AC900 to broadcast on a fixed channel that is not often used, e.g. 2 or 3 or 8.
View 2 Replies View RelatedWe have recently purchased some Cisco 3750x switches and we are getting complaints from users that the performance is poor when both the PC's NIC and switch port are fixed at 100/Full?
There are no errors or collisions on the switch interfaces so there is no obvious problem on the switch. The PC's are standard DELL Optiplex 755/760's
or gx 520's.
Any performance issues when configuring the switchport to 100/FULL?
This is IOS 15.1(4)M3 on a 1921 router. The LAN is 192.168.42.1/24. (DHCP config is further down.) We have a small range that we want to assign via DHCP to devices; .200 through .220 . At the same time, we have a handful of Macintosh systems to which we want to assign a specific address that is not in that 200-220 range. I don't want to configure the assignment based on the Ethernet MAC addresses because these systems might connect via UTP or wireless; that is to say, they have more than one MAC address. They only ever connect using one interface/MAC address at a time, but it's their choice; in some areas wi-fi is available, and in some areas they have to cable-up.
The Mac OSX network settings has a field for "DHCP Client ID". It would be much easier to tell the users of these systems to put their Mac's name in the Client ID field for both their wired and wireless DHCP configs. (As opposed to having them all lookup, and then give me their Ethernet MAC addresses for both of their interfaces.) I tried this with my Mac's (named "shrike") wi-fi interface, but I don't get the 192.168.42.14 address that I expected. I get an address from the .200 to .220 range.
Here's the DHCP-related config from the router:
router#sh run | s dhcp
ip dhcp excluded-address 192.168.42.1 192.168.42.199
ip dhcp excluded-address 192.168.42.221 192.168.42.254
ip dhcp pool OurOffice
network 192.168.42.0 255.255.255.0
[code]....
Is "client-name" the wrong place to configure the DHCP Client ID?
my prepaid broadband connection always drops to 0 every after 30s - 1min. It increases its speed only if I load a page or download, after finish loading, speed drops again to 0.
View 6 Replies View RelatedI have a Belkin Play N600 HD router. Does it have the capability to let me assign fixed IP addresses to devices like printers, NAS drives, and cameras so I know where they are?
View 2 Replies View RelatedIn cisco 1841 clock time is not stable.Every time the clock time is changed.
View 4 Replies View Relatedwhat is a good IOS version to stick on a 3750 (normal, no X or G series) switch? This is being used for a Cisco Lab in my CCNP - SWITCH studies.Normaly I referance INE's site though they dont have a 3750 (only 3560) IOS recommendations.
View 6 Replies View RelatedI am having some difficulties to have a stable connection on a Cisco 881. I have a IP Sla running with an ICMP-ECHO towards the uplink router. Linked with this is a tracking on the IP SLA so I can shutdown an HRSP instance with the tracking. The desired result is with this that when the nexthop becomes unavailable HSRP switches to the second router with the backup connection.
Regardless whatever timeout or threshold, the tracking switches at a random point when the line is somewhat congested. Debugging it shows me only a time-out on the IP SLA.
Is there anything possible to get the icmp-echo to retry it 2-3 times or so before going it's status is set to failure? [code]
Site-to-site tunnel between 881 router and ASA 5510 don't work stable,When PHASE 2 completed and Ipsec Tunnel has been builded, 881 resend some entities which will increment error counters.
View 1 Replies View RelatedSometimes even if my connection is cable my router gets a yellow light..what can be the most stable firmware to use?
View 3 Replies View Related