Cisco Switching/Routing :: 3560X Not Booting And No Lights Except On PS Module
Mar 3, 2013
I have a brand new 3650x switch that I was configuring via console and left it on overnight; this was friday night ( I forgot to keep the air conditioner on). When I returned Sunday afternoon and checked the switch I realized that the SYS and STAT lights on the front were not on, however the Leds on the PS module were still on. I powered it down and turn it on again but still there are no lights on the front. The PS OK and AC OK leds on the PS module are on but I noticed the leds on the two fan modules are not green or even amber; they are off.When I first turned on the switch I remembered distinctly that there were loud noice and if all fans were in overdrive mode for a few seconds then the went to normal. I'm not gettgin this loud noise phenomenom.
View 9 Replies
ADVERTISEMENT
Jan 17, 2013
My management has tasked me to give them a high level overview of the different switching we can choose for our new building.
This is what I know so far.4 Closets, each closet has 450 ports,One MDF room that is will contain one UCS Chassis and a Nimble iSCSI SAN.
I am working on the spreadsheet and it looks like this (Not totally filled):
2960s3560x3750x45064510Approx cost (Each, 48PORT, POE+, 10G uplink, Dual PS, IP BASE)
6K7K8K45K75KMax Capacity192432432192384Backplane speed206464520520ProLeast ExpensiveStackable to 9Stackable to 9ProDual PSDual PSDual PSDual PSDual PSProLayer 3 opt
Layer 3 optDual SupsDual SupsConExpensiveExpensiveConNo Dual PSConLayer 2 OnlyCannot stack more than 4
For the MDF I would like to use 2 Nexus 5548's with FEX's, and the layer 3 daughter board. For the IDF's I was thinking of two 4010's.
View 12 Replies
View Related
Nov 17, 2012
Yesterday a coleagu accdently removed the CF card from the router now the router does no longer want to boot completely. It extracts the image from the CF card but when it has to initialize the configuration it stucks there for hours. Can it be that the startup config is somehow corrupted?
When i try to tftpdnld is says that the mac address is illegal.
The first line of the cookie looks like 04 ff 08 86 ff ff ff ff ff ff ff ff ff ff ff ff
System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)Technical Support: [URL], Inc.PLD version 0x10GIO ASIC version 0x127c2801 platform with 196608 Kbytes of main
[Code]......
View 7 Replies
View Related
Aug 13, 2012
i facing problem with my switch cisco 3560G, when it power on only System light is green and noting happen. i check with serial cable ( Console) but noting happen no booting.
View 2 Replies
View Related
Feb 3, 2012
I have a 6500 that keeps booting into Rommon, even though it has a valid image file on the sup-bootdisk, and the config register is 0x2102. When it reloads I see this on the screen: [code] It seems like the repeating error is "error - on read during ELF program load". I can boot the system off of a CF card, but I'd like to use the sup-bootdisk.
View 11 Replies
View Related
Apr 7, 2012
Yesterday I've faced a Problem that is not letting me boot with the new IOS.
Actually I'm planning upgrade IOS which supports SSH. As part of plan I've downloaded the new IOS image and uploaded via TFTP server to the switch.
After uploading to the switch. I've verified image and MD5 hash also. Everthing is fine. Then after I set the boot variable for the newly uploaded Image.
When I'm rebooting the Device it is not taking the new IOS. It's booting with the OLD image. Even It's not showing any error message while rebooting (ACTIVITY FILE ATTACHED FOR YOUR REFERENCE) I can't take risk by deleting the old IOS.
View 1 Replies
View Related
Nov 3, 2012
I tried to upgrade the IOS on my internal AP and now I am in a reboot cycle. I have tried to manually boot the old and new IOS images from the rommon but neither are working. here is the output I am getting:
ap: dir flash:
Directory of flash:/
2 -rwx 6563840 <date> ap801-k9w7-tar.124-21a.JY.tar
4 drwx 256 <date> ap801-k9w7-mx.124-21a.JA1
152 -rwx 548 <date> env_vars
153 -rwx 2775 <date> cpconfig-ap801.cfg
154 -rwx 2775 <date> back_up.txt
155 -rwx 3763 <date> config.txt
[code]....
View 2 Replies
View Related
Aug 11, 2012
I'm having an issue with 2 of my 3560s which are not booting. The last thing I did on both switches before it hangs was:
>write erase
>reload
restarted as normal
[Code]....
I've tried powering-off the switch and pressing the Mode button and power on. I got to swtch: mode switch:reset
It restarted past the POST but just hang halfway at the same bootp-up process as shown on the attached. The SYST LED is Green color when it hangs.
View 9 Replies
View Related
Oct 25, 2012
I bought a CISCO SG200-18 switch. I added the Switch to my LAN and started the Switch (as described in the manual). The Switch starts the booting procedure (green blinking status LED) After a while, the LED starts to blink orange and green, instead of steady green.
In generally the Switch seems to work. I can access my whole network, but not the web interface of the switch itself. I also can't see the switch in the ADSL / DHCP rooter.
I also tried to boot the switch only connected to the PC. But ping on 192.198.1.254 is not working. The switch is in the same subnet like my other LAN components.
Subnetzmaske . . . . . . . . . . : 255.255.255.0
Standardgateway . . . . . . . . . : 192.168.1.1
I exchanged the switch. But the new switch shows the same behavior.
View 3 Replies
View Related
Aug 22, 2012
I have a new cisco 1941 router that I am setting up with pxe-booting. I have never setup pxebooting before and i have this setup so far ip dhcp pool Admin
-option 66 ip 192.168.1.4
-option 67 ascii pxelinux.0
and i can pull an ip but it keeps getting hung up when it comes to the TFTP part.
View 4 Replies
View Related
Jul 3, 2012
An ASA 5505. Device boots to rommon #0> and stays there. The complete boot record follows:
CISCO SYSTEMS
Embedded BIOS Version 1.0(12)13 08/28/08 15:50:37.45
Low Memory: 632 KB
High Memory: 507 MB
[Code]....
View 15 Replies
View Related
Mar 6, 2013
i cant find any difference in these two devices when i am trying to compare throughput.I need upgrade our new POP and there will be around 4900 MAC adresses in VLAN 150 and 130 MAC adresses in vlan 200.Uplink is 1 gig routed internet connection and there is 14 downlinks to separate villages.i found a few differences for eg stack interface on 3750x but i dont need it.
View 2 Replies
View Related
Oct 24, 2012
i am facing time daely issues on cisco 2960 s series switch while booting .It is taking time for electing masrer and sleeve for stacking.can i disable the election process for stcking while booting.
View 4 Replies
View Related
Jul 23, 2012
One of the 6500 was going in bootrom mode, so I have formated the flash disk using the other Cisco 6500 switch and copied IOS file to the boot disk. But the 6500 booting failed.
View 6 Replies
View Related
May 23, 2012
I unpacked a new 3560x and went to put our standard code version on it c3560e-ipbasek9-mz.122-53.SE2. Everything seemed to upgraded fine but it won't boot to a console prompt. It seems like it loads the IOS image fine but can't get passed the Front-end Microcode IMG MGR: Programming device 0. [code]
View 4 Replies
View Related
Feb 9, 2012
We have a small site that has an Avaya voice switch connected to a c3560x switch.The avaya tech told us to set this on our ports to which the phone and the desktop are connected.
View 4 Replies
View Related
Feb 29, 2012
today I received a Cisco 1841 Router with a problem i have never seen before. Maybe this my 1st really,really broken Cisco Router. When I power the Router on, the fan and all lights turn on (green) and that's it. Nothing changes, also after minutes of wating. On console i don't get any messages and I already tried every BAUD rate possible. Switched the router off/on again and again. And no, it's obviously not a console problem of my computer, because i tried with different routers.
View 3 Replies
View Related
Dec 5, 2011
I have a 4507R with a WS-X4515 supervisor V. It was booting into rommon mode, so I attempted to boot to an IOS image from TFTP. The boot process hangs at at the end of the below output and the then the status light blinks orange. I left it sit like this overnight, and it remained the same.
rommon 23 >boot tftp://x.x.x.x/cat4500-entservicesk9-mz.122-53.SG2.bin
Tftp Session details are ....
Filename : /cat4500-entservicesk9-mz.122-53.SG2.bin
[Code]......
View 9 Replies
View Related
Jul 7, 2012
One of my customer had a problem with A/C and the room temperature reached almost 50 C. We came to the site and saved the configuration, took a backup and shutdown the switch.
After the A/C problem is resolved, we tried to power-on the switch .. and we found that it is going to the rommon.
I put "boot" command to boot from the bootdisk, but I am getting the following error:
Code...
I tried to search it, But it is resulting in that most probably it is a hardware failure on the SUP.
View 6 Replies
View Related
Jul 17, 2012
I have 2950 switch booting through MOnitor Mode.Analyzed there is no Cisco IOS image in flash.
View 1 Replies
View Related
Dec 12, 2012
I have a Catalyst 4506e that works fine but if reload, it boots in rommon mode. I can start it with a boot command, but by default, i must type a command. My config-register is 0x2102.
View 5 Replies
View Related
Feb 28, 2012
I have a cisco 7606-S with dual RSP720-3CXL. Devices reloaded and now none of the RSPs are booting.When I have tried to take the console using only one RSP, card going to rommon mode after that it hangs. I guess its firmware is corrupted.
View 4 Replies
View Related
Nov 3, 2012
I noticed on my new cisco 2960s switches, that all the lights went orange for about 10 seconds then went off again, this was during normal operation, all ports were shutdown at the time apart from a few,the ones that were enabled, the led's went off.
View 3 Replies
View Related
May 8, 2012
I have a Cisco catalyst switch 3750G has all LED lights staying amber still without blinking, I cannot console into it and it can’t boot past the POST.
THE ISSUE HAPPENED ON THE NETWORK AND IT WAS ISOLATED FROM THE NETWORK, SO NOW I AM TRYING TO RESOLVE IT OUTSIDE THE NETWORK
View 3 Replies
View Related
Sep 2, 2012
I was called into a company today to look at their Cisco 7604 router as it had stopped working. The supervisor has all it LED in orange state, there was no blinking of the lights at power on they went straight to orange. Tried removing all cards, having only supervisor card in, etc but always the orange lights.
View 2 Replies
View Related
May 14, 2013
I have seen a similar post here from last year about a 10/half connection, but this is different. I have a provider using a 2950 switch (they left CDP on so we can see it). And we have to be set to 10/full to make this connection (as you know 10/half connected here would be or is horrible). I have had this connection running on my 2921 router w/o issue but when I connect it to my 3560X, then I get no link light (shows down/down, not connected).
What else to know about what has been tried: Connecting link to switch with switch set to auto/auto (sp/dup). Speed is 10 (as it should be) but of course w/o the other side pulsing the voltage to know what to auto to, it defaults to half so this is unacceptabel, but, I do get a link light and can pass traffic, it's just a horrible experience.
Also tried the same setting speed and duplex vs. auto disco speed and duplex on other ports of the switch, no difference, same results. Also different patch cables, same results.
My current work around is to connect the providers 2950 (10/full) to my 2921 router @ (10/full) with a BVI to another port on the router which continues on to my 3560X at 1G/full. And this works just fine. Here's more info from my 3560X and the providers 2950:
3560X:
License Level: ipservices
License Type: Permanent
Next reload license Level: ipservices
[Code].....
View 11 Replies
View Related
May 23, 2013
If the 3560 or 3750 "X" series support GRE.I am pretty certain the older 3750-E does not support GRE (both in hardware and software)Was hoping the new super duper X series do. If not, it could get expensive
View 5 Replies
View Related
Feb 18, 2013
I have a 3560X switch with interfaces 36-48 on the same LAN. All interfaces are switchports. Hosts on 38, 39 and 40 are multicast senders: all sending to the same single multicast address. Hosts on 36 and 37 are receivers, having joined that multicast group. I created an SVI for the LAN and put it in ip pim passive. (That is the only PIM mode allowed for an SVI with my IOS.) Show ip igmp snooping groups shows that 36 and 37 are the only interfaces in this group. I attach a laptop to interface 42 and Wireshark, and the laptop is receiving the multicast traffic. The laptop does not join the group. I expect it would not see the traffic.
View 4 Replies
View Related
Jan 25, 2013
last week we have changed the connection of small town from licensed radio to direct fiber with clasic 1gig sfp.After that we have connected the new fiber , we can see 5 min outages of customer internet connection. If we are conncted on the same subnet anywhere on network, we can ping the customer all the time. But if we try to ping the customers public IP it is each 5 min for 5 min unreachable. I have tryed to sho logg in all switches but there are no mesasages. I just see, when comunication have lost, the MAC and IP of customer will disapear from routers ARP tabbel. What is going on?When i enter sho mac address-table i can see customers MAC address in all switches. There are exactly 5 min outages. 5min it runs ok, 5 min outage and it repeats agan.
I looks like the swith blocks the ARP packets from customers to their default gateway.The routers are connected to catalyst 3560x lan base ios, This switch is connected to another 3560x lan base ios and it is connected with fiber to ME3400 where are customers connected.
View 2 Replies
View Related
Jan 24, 2013
I have 3560X-24T-S switches with IP Services loaded at remote sites that I have been having troubles with. Originally, they had IOS 12.2(58)SE1 on them. I have up to four diverse paths via point-to-point microwave at the remote sites. The Microwave equipment is by Microwave Networks and is a Prodeus M series which Ethernet support. The original issue manifested itself as hardware loopback errors on some of the ports that were connected to the microwave links.
My experience in the past has been that when a hardware loopback error occurred it is usually a bad switch port. In this case however, if I disconnected all of the microwave Ethernet links and rebooted the switch and then connected the Ethernet connections to the microwave links again, everything works fine. No hardware loopback errors. That is, until the next switch reboot. Then the hardware loopback error would return. Interestingly, it would come back on different ports connected to the microwave links every time. So if a reboot was done without disconnecting the microwave Ethernet links the hardware loopback error would change from one microwave link to another after each reboot.
I then went through and read the lengthy release notes for IOS version 15.0(2)SE and found several fixes that I thought could fix my issue. So I downloaded it and updated a couple of the offending switches (not all of them were having this problem). After going through the second update required to resolve the 'open file error' that happens going between 12.2(58)SE1 and 15.0(2)SE the problem seemed to be resolved on the offending switches. So, I went ahead and updated the IOS on all of the switches with point-to-point microwave connections.
I now have one switch that was updated that is crashing and rebooting continuously when the Ethernet links for the point-to-point microwave are connected. Again, if I disconnect all the microwave links and reboot, it comes up fine ands stays fine when the microwave links are connected back up. It will work fine until the next reboot and then the crash and reboot loop starts over again. Below is a portion of the putty log when the crash occurs:
----------------------------------------------------------------------------------------------------------------------
previous memory block, bp = 0x59BF838,
memorypool type is Processor
data check, ptr = 0x59BF860
========= Dump bp = 0x59BF87C ======================
59BF77C: 0 0 0 FD0110DF AB1234CD FFFE0000 56 383FDB4
59BF79C: 212AC68 59BF838 59BF6F4 80000042 1 0 A504F53 543A2050
59BF7BC: 6F727441 53494320 506F7274 204C6F6F 70626163 6B205465 73747320 3A20456E
[code].....
View 1 Replies
View Related
Oct 12, 2012
It would be so easy but failed to upgrade 3560X switch to ip services licence is bought and paid for mail and log from the CLI and tftp server attached
View 17 Replies
View Related
Mar 14, 2012
Im going to be ordering a new 3560X L3 switch (ws-3560x-48pf-s). We currently have a 3560 V2 switch and I've read it supports stacking, but looking at the back I just see a console port. Is there an extra card I have to get for this 3560V2 to make it stakable with the 3560X?
View 3 Replies
View Related
Feb 20, 2013
I was viewing the 3560x switch datasheet and i need network module C3KX-NM-10G. I have dark fiber with over 12 km distance to i guess i will be needing SFP EX for single mode.
View 3 Replies
View Related
