I was viewing the 3560x switch datasheet and i need network module C3KX-NM-10G. I have dark fiber with over 12 km distance to i guess i will be needing SFP EX for single mode.
View 3 Replieswe're upgrading over 40 of our 3550/3560 switches to the 3560x platform - what I have noticed is that we get quite a few PoE issues when migrating the site - for instance, 90 - 95% of the site's Cisco's phones will come up but not all of them - the best way to resolve that issue is to identify the ports that haven't came up and then shut - wait 10 secs and no shut.
View 9 Replies View RelatedWe have a small site that has an Avaya voice switch connected to a c3560x switch.The avaya tech told us to set this on our ports to which the phone and the desktop are connected.
View 4 Replies View RelatedI acquired a 3560X-24P-L Switch which I wanted to use at our datacenter. However, I need a switch that supports OSPF. It came with a Universal IOS but there was no "Router" command under conf t. I downloaded and applied the latest "IP Base" IOS, but still no Router OSPF. Based on the matrix here > [URL] I thought "IP Base" supported OSPF, but what exactly is "OSPF for routed access" ? Do I actually need an "IP Services" IOS? From my download options, I do not see an IP Services IOS for the 3560X-24P-L so I'm left to assume that the switch does not support L3 / OSPF. So my question is this particular switch supports L3 / OSPF and what is Universal IOS?
View 5 Replies View RelatedI have Cisco 3560X L3 switch and i need to configure DHCP on this switch. I have already configured below mentioned VLANs
VLAN 10 - 192.168.8.254 (USER VLAN)
VLAN 20 - 192.168.152.254 (REMOTE & VPN USERS VLAN)
VLAN 30 - 192.168.0.254 (SERVER VLAN)
After configuring DHCP, all the users needs to get IP from USER VLAN and all the servers should get IP from SERVER VLAN. If yes, what are the steps as I am very new in this kind of configuration.
I am trying to join a Cisco Catalyst 3560X-24T-L to an existing VTP domain, my question is what configurations should I do to this switch?I have already gave it a hostname, setup passwords, enabled telnet, created a management address on port g0/24.I would like it to be on VLAN 13, is this done from my server switch, or done on the new switch?
View 10 Replies View RelatedI haven't worked with infrastructure much lately but planning on replacing a Dell switch used for a small iSCSI SAN with a Cisco 3560x. Switch is sstorage ONLY, network handled through different switches. I believe I want to disable spanning tree and configure trunking for the 4 GB ports connected to the storage array. The switch is providing connectivity to SAN via multiple GB connections and then also multiple GB connections to 3 Vmware hosts.Can you look over the changes I made to config below and let me know if I am on the right track.
I also plan to add a second switch later with the 10GB modules to interconnect for redundancy (but not worried about that part for now). I do not plan on using jumbo frames.
Here are my questions
1) Is the best way to globally disable spanning tree for the switch?
2) Did I trunk the ports correctly below?
3) Should I apply any specific SmartRoles to the 4 SAN NICs (GE1-4) or to host NICs (GE13-20)?
4) Anything additional I should do to handle iSCSI data?
Here is a copy of the config so far with my changes marked in RED.
storage1#wr tBuilding configuration...
Current configuration : 1696 bytes!version 12.2no service padservice timestamps debug datetime msecservice timestamps log datetime msecno service password-
[Code].....
i have a cisco 3560x poe. ny currnet version is 12.2(58)SE2.the cpu process is aboute 30% average.my problem is- ping to the switch itself show me 12ms which is high latency.*note- data between two hosts no this has no latency.i realize the packet go into the cpu itself but, the cpu is not loadedusy. so my question is- is this natural behavior?
View 2 Replies View RelatedDo you have the ability to setup DHCP servers on this layer 3 switch? I know I can with my old 3550 switch. Want to upgrade and make sure this model supports setting up dhcp servers on it.
View 3 Replies View RelatedI like the SG-300 switches for SMB and I'd like use them in our network. Design is quite simple just 6 SG-300 switches connected to one central switch using SFP ports (using 2 port trunks) so I need 12 SFP ports and this is my question. Could you recomend me switch with more then 12 SFP ports from Cisco for this SMB network ? I don't know all the Cisco product lines and I can't find it.
View 2 Replies View RelatedThe default Gateway and DHCP server is connected to port 1 of the switch. I have various other devices on the network plugged into other ports on the switch.I want port 1 to communicate with every port on the switch, but don't want the other ports to be able to see eachother unless I specifically allow them to. For example, port 5 should see port 1, and 7, but nothing else.Everything needs to be in the same subnet. With the older Dlink switches I am used to this feature is called "Port Segmentation" but I see no such option in this switch. I have been playing with the VLAN settings but so far I have not been able to achieve this.
View 7 Replies View RelatedI have a statck of 4 2960s switches, with POE powered access points on 2 of them. All of the access points appear to be functioning normally. For some reason, on 3 interfaces connected to access points, I get the following when issuing show interfaces status:
Gi3/0/9 connected: T 7 a-full a-1000 10/100/1000BaseTX
^
My question is regarding the "T" in the status field. I can't find any documentation on this.
My SG200-50P Switch Log appears as follows with Random ports going up and down. I am trying to find out if this links to another problem I'm having with a Client Server software locking up on the client end. The hardware, thin clients and desktops, are working and have checked all sleep and power settings. All items in working order, now I'm wondering about the switch
2147483369 2013-Feb-20 15:12:07 Warning %STP-W-PORTSTATUS: gi19: STP status Forwarding
2147483370 2013-Feb-20 15:12:02 Informational %LINK-I-Up: gi19
2147483371 2013-Feb-20 15:12:00 Warning %LINK-W-Down: gi19
2147483377 2013-Feb-20 14:51:31 Informational %LINK-I-Up: gi45
2147483378 2013-Feb-20 14:51:28 Warning %LINK-W-Down: gi45
[code]....
I've a 7206VXR (NPE-G1) router. I would like to purchase a PA-GE port adaptor where I've to use a GBIC connector.
1. Is it possible to have a connection between PA-GE and a 3560G switch (4 SFP ports)? If yes, what type of cables & connectors are to be used?
2. Is there any GigabitEthernet port adaptors / modules for 7206vxr where I can connect RJ45 (cat 5) or SFP modules?
I have been reading the postings on this site trying to retrieve the MAC address for the client devices (computers, printers) attached to our switches. We have approximately 500 switches and I need to map the mac address to the switch. It appears the OID information is for SNMP v2. We are restricted to using only SNMP v3. I have tried using the Cisco SNMP Object Navigator without any success.
View 2 Replies View RelatedI have a Cisco 4500. Recently some of the ports seem to have "died"/ will not supply Poe to phones. Some work for data only. Other do not work at all. The switch has been restarted, this made no difference.
View 2 Replies View RelatedI have a 2960 switch and every then and now the ports are flapping, while i was on console i saw ports going down and coming up...when the ping to machine ip addresses timed out the port status on switch was still up...no errors collisions seen on sw port. Below is sh int when the port was flapping
[code]...
I have a got a requirement where a 24 Port Switch should have 4 SFP's and all 4 should be used at a time, So I've chosen " WS-C2960S-24TS-L"
The transeiver should be GLC-LH-SM, so kindly let me no whether I would be able to use all 4 ports at a time or not.
I work at a hospital and we have 3750X-48P switches in stacks in various locations throughout the hospital. We have noticed that when an EKG machine is plugged into one of the ports on some of these switches and the EKG machines are set manually to 100/Full, the ports are no longer usable until the switch is restarted. The switch is configured for auto. If the EKG machine is set to auto, it will work and not cause problems. The link on the interface will show up/up and there will be output packets increasing. However, there will be no inputs on the link and the port is unusable. Unfortunately, even when the device is removed, the port becomes unusable for any device. Is there any way to fix this problem without rebooting the switch?
View 5 Replies View RelatedIn my environment we have 3750x switches running ios 15.0 (1) SE2. We have port security mac address sticky configured on all our switch ports. I noticed that we have several interfaces (on different switches) that are up but have not captured the MAC address from the workstation. Here is one example:
interface GigabitEthernet2/0/11
switchport mode access
switchport port-security
[Code].....
I was checking some things on my Cisco 4500 and spot checking some of the ports. Using CNA it says it is at 10. The web browser to the switch says Full-duplex, 1000Mb/s, link type is auto, media type is 10/100/1000-TX on port 6i/18 The CNA says, so what would cause the difference?
View 3 Replies View RelatedI have a Cisco 3750G-48PS Running IOS 12.2(40) and was wondering how many physical ports are supported in an LACP Configuration. Is it 4 or 8 ports in a single switch.
If I have a dual 3750 stacked together, and I want to configure (8) port LACP, Can I take (4) ports from each switch in the stack and LACP together.
Have our public IP address space masked on /24 at our Internet Router. The router portion of 3845 connects to Internet, while the internal switch connects to my internal network and seeds it with the public address space. The switch had a port configured no switchport (L3) with an ip address with /24 (ie 67.63.145.1 /24) this connects to internal IPS/IDS then to Firewall which NATs to internal, then packet shaper, web filter etc etc etc. I need to test my ISP speed so I need to "break in" to the link between the switch and the IPS/IDS. I figured I could configure another port on the switch on the 3845 but my problem is the port to my network is routed and is masked on entire /24. I tried to configure a port on VLAN 1 and give myself an available address in the L3 address space and this did not work (figured it would not but gave it a try)
Any way to get two ports configured to use the same subnet while one is a L3 routed port and the other is just part of that layer 3 routed network?
i recently deployed cat4507e switch along with 3 nos of WS-X4748-RJ45V+E - 48 port gigabit PoE modules. I am using polycom IP560 phones.
I am facing issue of some switch ports (randomly) stops supplying power to phone at random time. So far there are about 4 incident and i have been plugging those connection to different - usused ports. I am planning to RESET the switch module during weekend and i think it might fix issues with those ports.
But what would be quick and easy way to fix this issue when the issue is faced? How/what to check on switch port interface wrt to power? If switch module is falling short of overall power requirement, is there a way to boost the power?
Is there a switch that handle its 24/48 ports at 10 Gbps with copper?. I have checked 3750 X but just handle 2 SFP with 10 Gbps.The requirement is to use this switch as CORE and connect 12 switches (access) using its uplinks at 10 Gbps with copper ( in this case 3750 X can be used).using copper at 10 Gbps the distance is still 100 m?
View 9 Replies View RelatedI have to configure failover Active/Standby on my ASA 5510.I am wondering how i could do for the outside interface, i mean, actually the ASA1 outside interface is linked directly to our Internet router.So now if i have to add ASA2 connecting to that router i will need a switch between them.I have already a switch for DMZ & LAN.The thing is that i will have to allow 3 switchs ports to communicate with each others.
- 1 for ASA1--outside
- 1 for ASA2--outside
- 1 for Internet router
How could i isolate these 3 ports to make them communicate alone ? Should i use VLAN for that ?And if i use VLAN, will this require to make any change of configuration on my firewalls (ASA1 & ASA2) outside interface ?I am a bit lost with this, if i am correct i will not have to do some "vlan tagging" on the firewall itself ?
My network generally runs older routers (2600 series) with 16 port switch modules (NM-ESW-16). This has always worked great since I can configure the router and the switch ports on the fly, making changes to either as necessary. Well I am upgrading to 2811 routers, and we wanted to get gigabit ethernet ports on our switch modules. I think I made an error when I purchased a few of these switch modules: NME-16ES-1G.
The first problem, is that the switch ports don't even show up on the router config, I have to establish a session into the switch, (And I can't seem to get back to the router unless I manually switch off power and restart). I don't like this type of switch module, it's like I'm running a completely separate device, and while having a layer 3 switch is cool, It doesn't let me setup routing protocols so I don't like doing it this way. I want to go back to using a switch module that simply adds a ton of ports to my router like the NM-ESW-16. (Note: The NM-ESW-16 does actually work in the 2811 and would be perfect if it were Gigabit speed.)
The seconds problem is that the NME-16ES-1G isn't actually a Gigabit switch. It has a single gigabit port, but the 16 ports are all Fastethernet, and not gigabitethernet. So ideally, I am looking for a switch module that I can fully configure from the router interface that has 16 gigabitethernet ports, and works with a 2811. IE I want to do this. [code]
I am working on a request to clean up alot of excess cabling in one of our IDF's. I noticed that many of the connections have no lights on them and probably haven't been used in a long while. I would like to know if there is a CLI command I can run on the Cisco 3750 switch will allow me to bring up a list of ports which have not seen any activity for a period of time - for example, 30, 60, or 90 days.
View 3 Replies View RelatedCan i configure access ports into port channel on Nexus 7K switch.If possible then provide the complete configuration.....
View 2 Replies View RelatedI have 4 cisco 2960 switches to which many users are connected. No vlans are the only default vlan 1 is there. Now I want to make ether channel on switch 1 whcih has 24 fast etherenet ports. Can I make port 1- 8 as one ether channel which are connected to users or i can only make ethere channel of ports that are connectd to other switchs. If I can, how the other switchs will comnicate with the switch ports bundalled in the ether channel in switch 1.
View 6 Replies View RelatedI have a Cisco 6509 with IOS "s222-ipservicesk9_wan-mz.122-18.SXF16.bin"I need to enable dot1x on user's ports on the switch. each user is connected to the switch through the IP phone.
I just found out that I can not enabled dot1x on trunk port. I have tried to use "switchport voice vlan " but I got:
Switch(config-if)#switchport voice vlan 123
Command rejected: Gi7/20 is Dot1x enabled port.
let me know what should I do to get dot1x working?
Note: I have connected a laptop directly to the port and dot1x is working fine.
Can you configure a Cisco 1941 to use an 8 port EHWic module and the 2 onboard GE ports in a single LAN?
I've discovered you can't have the on GE ports associated with a VLan, and I'm when I've previously researched for a solution, bridging was mentioned but I cannot seem to get it to work (or completely understand it)The reason I would like to use all 10 ports on for the LAN is becuase I have 10 devices I need to connect to the 1941?
My management has tasked me to give them a high level overview of the different switching we can choose for our new building.
This is what I know so far.4 Closets, each closet has 450 ports,One MDF room that is will contain one UCS Chassis and a Nimble iSCSI SAN.
I am working on the spreadsheet and it looks like this (Not totally filled):
2960s3560x3750x45064510Approx cost (Each, 48PORT, POE+, 10G uplink, Dual PS, IP BASE)
6K7K8K45K75KMax Capacity192432432192384Backplane speed206464520520ProLeast ExpensiveStackable to 9Stackable to 9ProDual PSDual PSDual PSDual PSDual PSProLayer 3 opt
Layer 3 optDual SupsDual SupsConExpensiveExpensiveConNo Dual PSConLayer 2 OnlyCannot stack more than 4
For the MDF I would like to use 2 Nexus 5548's with FEX's, and the layer 3 daughter board. For the IDF's I was thinking of two 4010's.